TWAC-15CD/K8R1 TWAC-18CD/K8R2 TWAC-22CD/J3R2 TWAC-24CD/J3R2
INTRODUCTION IMPORTANT SAFETY INSTRUCTION ...........................................................................1 ELECTRICAL REQUIREMENTS ................................................................................... 2 PACKING LIST ............................................................................................................3 INSTALLATION&ASSEMBLY INSTRUCTIONS .............................................................. 4 USING YOUR AIR CONDITIONER .................................
1
15K 2 18K/22K/24K
/16" Long Hex-head Screw 5/8" Long Hex-head Screw 1/2" Long Hex-head Screw 5/8" Long Flat Head Bolt and Locknut Sill Angel Bracket 1/2" Long Flat Head Bolt and Locknut Gasket Support Bracket(with R and L remark) 3
15K/18K 22K/24K 17.91 18.625 23.625 26.50 19.00 19.50 28.00 30.00 41.00 41.
(15K/18K See FIG.1/FIG.2 ; 22K/24K See FIG.3/FIG.4). FIG.1 FIG.2 SASH SASH 19 MIN 1/2 MIN 19 MIN 1/2 MIN 1/2 MIN Storm Window Frame or Obstruction Storm Window Frame or Obstruction FIG.3 FIG.
FIG.5 FIG.6 FIG.5 FIG.6 FIG.7 & 8 FIG.9 FIG.9 FIG.7 FIG.
6.Remove the six screws from the cabinet.(Every side for top,left and right has two screws.) (FIG.10) FIG.10 FIG.11 FIG.11 8.Take the pearl cotton for 24K(FIG.12). FIG.
FIG.13a FIG.13a 5/16 Long Hex-head Screw FIG.13b14. FIG.13b 5/16" Long Hex-head Screw FIG.14 (Suggest to keep a downward oblique, to let accumulated rain water to drain out, from back side of the unit bottom.
Long Flat head Bolt and Locknut 5/8" Long Flat Head Bolt 5 (It should set on the gasket for 22K/24K) Long Flat head Bolt and Locknut 5/8" Long Hex-head Screw Gasket 5/8" Long Hex-head Screw 1/2" Long Hex-head Screw 9
sash lock Sash Lock 5/8" Long Hex-head Screw FIG.
15K/18K 22K/24K 18 1/4 (46.4 cm) 19 1/2 (49.5 cm) 23 7/8 (60.6 cm) 26 9/10 (68.3 cm) FIG.16 Y (Page 6 and 7) FIG.17 FIG.
FIG.19 FIG.
Cool Mode: The cooling function allows the air conditioner to cool the room and at the same time reduces Air humidify. Press the MODE button to activate the cooling function. To optimize the function of the air conditioner, adjust the temperature and the speed by pressing the button indicated. Dry Mode: This function reduces the humidity of the air to make the room more comfortable. Press MODE button to set the DRY mode. An automatic function of alternating cooling cycles and air fan is activated.
10. Directional Louvers: To direct the airflow, 6. Eco Button: When the unit is in ECO mode, the horizontal wheel to control the horizontal direction, light will turn on. In ECO mode, the unit will air deflector to control the vertical direction. turn-off once the room is cooled to the user set temperature. The fan will also be off at this point. The unit will turn back on when the room temperature rises above the user set temperature.
1 5. Timer: Use these buttons on the control panel and remote to set the Timer. Timer Off: The timed stop is programmed by pressing TIMER button. Set the rest time by pressing the button or until the rest time displayed is to your demand then press TIMER button again. Timer On: When the unit is off, press TIMER button at the first time, set the temperature with pressing the button or . Press TIMER button at the second time, set the rest time with pressing the button or .
FIG.21 FIG.
17
18