Instructions / Assembly

ManualsBrandsTCP ManualsKitchenConnected Smart Gateway

step #3 step #4 step #5

5A TURN OFF POWER TO LIGHT SOCKETS AT

WALL SWITCH OR LAMP.

step #7

7 PRESS THE SYNC BUTTTON ON THE

GATEWAY UNTIL THE GREEN ACTIVITY

INDICATOR BEGINS TO ROTATE.

step #1 step #2

GATEWAY AND BULBS

FOR CONNECTED BY TCP

PURCHASED SEPARATELY

SETUP GUIDE

QUICKSTART

1A PLUG ONE END OF INCLUDED ETHERNET

CABLE INTO THE CONNECTED BY TCP GATEWAY.

2A PLUG INCLUDED POWER ADAPTER

INTO THE CONNECTED BY TCP GATEWAY.

step #6

6A TURN POWER BACK ONTO BULBS AT

WALL SWITCH OR LAMP.

REQUIRED FOR SETUP:

• CONNECTED BY TCP GATEWAY

• CONNECTED BY TCP BULB(S)

• HOME WiFi ROUTER W/INTERNET ACCESS

• ANDROID OR APPLE SMART DEVICE

5A 6A

OFF

1B PLUG OTHER END INTO AN ETHERNET

PORT ON YOUR HOME WI-FI ROUTER.

2B PLUG THE POWER ADAPTER INTO ANY

STANDARD WALL OUTLET.

TIP: THE ETHERNET CABLE WILL “CLICK”

WHEN INSERTED COMPLETELY

5B SCREW CONNECTED BY TCP BULBS INTO

DESIRED SOCKETS.

6B YOUR CONNECTED BY TCP BULBS WILL

START SLOWLY DIMMING UP AND DOWN.

3 MAKE SURE THAT YOUR SMART DEVICE IS

CONNECTED TO YOUR HOME WI-FI NETWORK.

TIP: IF UNCERTAIN, CHECK THAT

WI-FI IS ENABLED ON YOUR SMART DEVICE.

TAP “TOOLS” FOR AN ANDROID DEVICE OR

“SETTINGS” FOR AN APPLE DEVICE.

IN THE WI-FI SECTION, LOOK FOR YOUR WI-FI

ROUTER NAME, SELECT IT, ENTER YOUR

ROUTER’S PASSWORD, AND LOG IN. YOU MUST

KNOW THE PASSWORD TO YOUR WI-FI ROUTER.

THE GATEWAY WILL ALSO STOP THE

SEARCH PROCESS AUTOMATICALLY 2

1/2

MINUTES AFTER FINDING THE LAST LIGHT

BULB.

AS EACH BULB JOINS YOUR NETWORK,

IT WILL TURN ON TO FULL BRIGHTNESS.

AFTER ALL OF THE BULBS HAVE JOINED,

YOU MAY PRESS THE SYNC BUTTON

AGAIN TO STOP THE NETWORK SEARCH

PROCESS.

4 DOWNLOAD THE “TCP LIGHTING” APP TO

CONTROL CONNECTED BY TCP BULBS WITH

YOUR ANDROID OR APPLE SMART DEVICE.

IN THE iTUNES APP STORE (APPLE

DEVICES) OR THE GOOGLE PLAY

STORE (ANDROID DEVICES)

NOTE: IF A BULB IS NOT DIMMING UP AND

DOWN, YOU CAN RESET IT BY TURNING POWER

TO THE BULB OFF AND THEN ON THREE TIMES

CONSECUTIVELY. WAIT ONE SECOND BETWEEN EACH

EVENT. (after the third cycle, leave the power on)

SEARCH FOR:

tcp lighting

All trade names are registered trademarks

of respective manufacturers listed. Apple,

iPhone and iTunes are trademarks of Apple

Inc., registered in the U.S. and other

countries. Wi-Fi is a registered trademark of

the Wi-Fi Alliance. Android and Google play

are trademarks of Google Inc.

step #8

8 TAP THE TCP ICON TO OPEN THE “TCP

LIGHTING” APP ON YOUR SMART DEVICE.

YOUR LIGHT BULBS ARE NOW READY TO

BE CONFIGURED USING THE APP.

TIP: IF THE LOGIN SCREEN COMES UP

JUST TAP “LOGIN.” DO NOT ENTER A

USERNAME OR PASSWORD.

Summary of content (2 pages)

PAGE 1
QUICKSTART SETUP GUIDE step #1 step #2 1A PLUG ONE END OF INCLUDED ETHERNET CABLE INTO THE CONNECTED BY TCP GATEWAY. 2A PLUG INCLUDED POWER ADAPTER INTO THE CONNECTED BY TCP GATEWAY. 1A step #3 3 MAKE SURE THAT YOUR SMART DEVICE IS CONNECTED TO YOUR HOME WI-FI NETWORK.
PAGE 2
step #9 9 ONCE THE APP IS LAUNCHED, IT WILL DETECT YOUR NEW CONNECTED BY TCP LIGHT BULBS, AND WALK YOU THROUGH THE SETUP PROCESS, ONE BULB AT A TIME. TAP “YES” TO GET STARTED. step #10 10 AFTER ALL OF THE BULBS HAVE BEEN FOUND BY THE APP, TAP “NEXT.” step #11 step #12 step #13 11 YOUR BULB(S) IS(ARE) NOW CONNECTED TO YOUR SYSTEM. TO IDENTIFY IT, THE BULB THAT IS NOW GETTING SET UP WILL BE DIMMING UP AND DOWN. FOR THE INITIAL SETUP, YOU CAN JUST ACCEPT THE INITIAL DEFAULT SETTINGS.