MSDS

SDS-001 - Issue Date: 3-16-09
Safety Data Sheet (SDS) LED Lamps
PRODUCT AND COMPANY IDENTIFICATION
Description: Trade Name (As labeled) LED Lamps (For general lighting application) (Consists of LEDs and drivers as a unit)
Manufacturer: Technical Consumer Products, Inc. • Shanghai, Jensen LTD. • 325 Campus Drive • Aurora, Ohio 44202 • 1-800-324-1496
COMPOSITION/INFORMATION ON INGREDIENTS
THERE ARE NO KNOWN HEALTH HAZARDS FROM EXPOSURE TO LAMPS THAT ARE INTACT.
Lamp Assembly – Glass and Plastic – Lamps may be manufactured from plastic or glass parts. The glass is made from soda lime similar to that used throughout
the glass industry for other common consumer items. None of these materials would present a potential hazard in the event of breakage of the lamp, aside
from the hazard due to broken glass.
PHYSICAL PROPERTIES Not applicable to intact lamp.
EXPLOSION HAZARDS When exposed to high temperature, toxic fumes may be released from broken lamps.
HEALTH CONCERNS THERE ARE NO KNOWN HEALTH HAZARDS FROM EXPOSURE TO LAMPS THAT ARE INTACT.
No adverse effects are expected from occasional exposure to broken lamps. As a matter of good practice, avoid prolonged or
frequent exposure to broken lamps unless there is adequate ventilation. The major hazard from broken lamps is the possibility of
sustaining glass cuts.
Glass Glass dust is considered to be physiologically inert and as such has an OSHA exposure limit of 15-mg/cubic meter for
total dust and 5-mg/cubic meter for respirable dust. Perform normal first aid procedures. Seek medical attention as required.
Inhalation If discomfort, irritation or symptoms of pulmonary involvement should develop, remove from exposure and seek
medical attention.
Ingestion In the unlikely event of ingestion of a large quantity of material, seek medical attention.
Contact
Wash eyes/skin, including under eyelids, immediately with copious amounts of water and Seek medical attention.
Eye/Skin
INFORMATION AND APPLICABILITY
Technical Consumer Products believes that under the Occupational Safety and Health Administration (OSHA) Hazards Communications Standard, a
lamp (light bulb) is exempted as an “article”, and that as such, does not require a SDS. The original OSHA Standard defined an article as something that:
1) is formed to a specific shape and design, 2) has end use functions dependent upon its shape and design, and 3) does not release or otherwise result
in an exposure to a hazardous chemical under normal conditions of use. In February 1994, OSHA amended the Hazard Communication Standard and
modified part 3 of the above to read: 3) does not release more than very small quantities of a hazardous chemical under normal conditions of use. State
and local regulations also contain similar exemptions for such articles.
Materials contained in the lamp are not released during normal use and operation.
The following information is provided as a courtesy to our customers.
Phosphor in LEDs – (nuisance dust) phosphate mix using manganese, rare earth elements such as lanthanum, and yttrium as either an oxide or as a
phosphate, along with a barium/aluminum oxide all are tightly bound in the phosphor matrix. These phosphors produce better lamp efficiency and color
rendition. The phosphor components may vary slightly depending on the color of the lamp. Some lamps may contain a thin coating of tin oxide inside the
glass.
LEDs – The LEDs consist of metal and InGaN (Indium Gallium Nitride) semiconductor chip. Due to their insolubility and inertnes, these materials do not
present a significant hazard.
PROCEDURES FOR DISPOSAL OF LAMPS Take usual precautions for collection of broken glass. Place materials in closed
containers to avoid generating dust.
ALTHOUGH TECHNICAL CONSUMER PRODUCTS, INC. attempts to provide current and accurate information herein, it makes no representa-
tion regarding the accuracy of completeness of the information and assumes no liability for any loss, damage or injury of any kind which may
result from or arise out of the use of/or reliance on the information by any person.
©TCP 2014/52722
TCP
®
325 Campus Dr. | Aurora, Ohio 44202 | P: 800.324.1496 | F: 877.487.0516 | tcpi.com
Phosphor There have been no significant adverse effects on humans by ingestion, inhalation, skin contact, or eye contact.
Antimony, manganese, yttrium and tin compounds are characterized by OSHA as hazardous chemicals, however, due
to their insolubility, relatively low toxicity and small amount present in the phosphor and lamp, these materials do not
present a significant hazard in the event of breakage of the lamp.
Capsule Lamps T20, T24 Series SpecificationsLED Lamp Safety Specification