User manual

ManualsBrandsTDE INSTRUMENTS ManualsPanel-Mount InstrumentsDPM72-MP

Digalox DPM72-MPN

Instruction manual

Visit www.digalox.com

to download

Package contents:

Panel meter Digalox DPM72,

1. Intended Use

• Indoor use non

condensing

• Panel mounting.

•

Failure to comply with these instructions will

•

Preferred supply of USB devices via scre

via USB in operation, USB supply voltage must be at least 5V.

2. Safety instructions

•

Note: the measurement inputs of the device can carry life

voltages!

• When working on the

device

the device!

•

Read instruction manual

• The device is not

intended to protect persons or facilities against harm. Specific

devices must be used to guarantee safety (prote

• When

connecting switches

whose isolation voltage

is at

voltage. For example,

when measuring

least 500V.

• Do not open the

housing!

• Do not use

the instrument

• All cables

carrying hazardous

----- 1 -----

Instruction manual

(Rev-2015-04)

to download

software “Digalox

Manager”

Panel meter Digalox DPM72,

5x jumpers, 1

condensing

, non corrosive.

Failure to comply with these instructions will

void

all guarantee and warranty.

Preferred supply of USB devices via scre

w terminals with 10 to

via USB in operation, USB supply voltage must be at least 5V.

Note: the measurement inputs of the device can carry life

device

hazardous voltages must not be connected

Read instruction manual

carefully before operating the device!

intended to protect persons or facilities against harm. Specific

devices must be used to guarantee safety (prote

ction relais, off

connecting switches

to the terminals J1-J6 only

switches must

is at

least twice the

maximum occurring

when measuring

250V AC switch

must be isolated

housing!

the instrument

in the presence of explosive or

flammable substances!

carrying hazardous

voltages must be secured

with external

Manager”

mounting bracket

all guarantee and warranty.

w terminals with 10 to

24V AC/DC. Supply

via USB in operation, USB supply voltage must be at least 5V.

Note: the measurement inputs of the device can carry life

-threatening

hazardous voltages must not be connected

carefully before operating the device!

intended to protect persons or facilities against harm. Specific

ction relais, off

-switches, etc).

switches must

be used

maximum occurring

measurement

must be isolated

for at

flammable substances!

with external

separators.

Summary of content (8 pages)

PAGE 1
Digalox DPM72-MPN Instruction manual (Rev-2015-04) Visit www.digalox.com to download software “Digalox Manager”. Manager” Package contents: Panel meter Digalox DPM72, 5x jumpers, 1xx mounting bracket 1. Intended Use condensing non corrosive. • Indoor use non condensing, • Panel mounting. • Failure to comply with these instructions will void all guarantee and warranty. • Preferred supply of USB devices via screw screw terminals with 10 to 24V AC/DC.
PAGE 2
3. Description The multi display with RGB backlight is able to display up to 4 parameters simultaneously. Thresholds can be associated with individual warning backlight colors. The unit can be switched between measurement modes via an external switch. Minimum and maximum values for each parameter are recorded and can be displayed optionally using an external switch. Measured values of one parameter are recorded over a time span of three minutes up to 14 days.
PAGE 3
4. Electrical Connections The device may only be operated in one of the connection options shown below. Fuse 250mA 10-24V Fuse 250mA 10-24V Us Us Us Us Supply Supply DPM72 MPN DPM72 MPN Voltage direct, current via external shunt Voltage direct, current via external shunt, high side, max. 50V Measure inputs Measure inputs U1low U1high U2high U1low U1high U2high U2low max. 200mV max. 500V max. 200mV Shunt U2low Load Shunt Load max.
PAGE 4
5. Configuration The device can be configured via DIP switches and jumpers manually or with the corresponding software “Digalox Manager” via USB interface. When configuring via DIP switches and jumpers the basic settings can be made computer-independent. The configuration with the software “Digalox Manager” allows full functionality. Setting scale via DIP switch When setting the scaling via DIP switch to represent the correct measurement value (e.g.
PAGE 5
Configuration via DIP switches and jumpers if it is required to switch between multiple measurement modes via an external switch (Save mode) The required measurement modes are configured and saved sequentially. 1. Connect supply voltage. 2. Set DIP-switch 10, 11 and 12 to OFF position. 3. Set the measurement mode with jumpers at J4-J6 according to table "Measurement mode”, column “Save mode". 4. Set DIP switch 10 to ON position. 5.
PAGE 6
Table common switch combinations Value Combination (DIP switch 1-9) 10 Value 50 ON 1 2 3 4 5 6 7 8 9 10 11 12 100 ON 1 2 3 4 5 6 7 8 9 10 11 12 100 ON 1 2 3 4 5 6 7 8 9 10 11 12 ON 1 2 3 4 5 6 7 8 9 10 11 12 500 ON ON 1 2 3 4 5 6 7 8 9 10 11 12 250 ON 1 2 3 4 5 6 7 8 9 10 11 12 25 Value Combination (DIP switch 1-9) 200 ON 1 2 3 4 5 6 7 8 9 10 11 12 20 Combination (DIP switch 1-9) 1 2 3 4 5 6 7 8 9 10 11 12 ON 1 2 3 4 5 6 7 8 9 10 11 12 Table measurement mode Measurement mode Displ
PAGE 7
6. Other settings The following functions can be activated independently by short-circuiting short connectors J1-J3 by jumper or switch during operation: Graphical historic data display To activate the graphical historic data display connector J1 is shorted. The unit displays the stored values within the set time base as a graphical trend. The time base can be set to days (7, 14), hours (6, 12, 24, 48, 72) or minutes (3, 15, 30, 60).
PAGE 8
7. Mounting Carefully insert the instrument into the panel cutout. Insert the mounting bracket from the back and push towards the panel until instrument sits tight. Make sure the mounting bracket is snapped into the side of the housing. To ensure IP65 protection (dust and water jet) when mounting in a front panel, use optional gasket. 8.