User manual

ManualsBrandsTDE INSTRUMENTS ManualsPanel-Mount InstrumentsDigalox DPM72-AV Graphical DIN-panelmeter for Voltage and Ampere

Digalox DPM72-AV

Instruction manual

Package contents:

Panel meter Digalox DPM72,

1. Intended use

• Indoor use non

condensing

• Panel mounting.

•

Failure to comply with these instructions will

2. Safety instructions

•

Note: the measurement inputs of the device can carry life

voltages!

• When working on the

device

the device!

•

The device must not be used as the only protective device or protective

shutdown.

•

Read instruction manual

•

The device is not intended to protect persons or facilities against harm. Specific

devices must be used to

• When

connecting switches

whose isolation voltage

is at least

voltage. For example,

when measuring

least 500V.

• Do not open the

housing!

• Do not use

the instrument

• All cables

carrying hazardous

separators.

----- 1 -----

Instruction manual

(Rev-2015-04)

Panel meter Digalox DPM72,

5x jumpers, 1

condensing

, non corrosive.

Failure to comply with these instructions will

void

all guarantee and warranty.

Note: the measurement inputs of the device can carry life

device

hazardous voltages must not be connected

The device must not be used as the only protective device or protective

Read instruction manual

carefully before operating the device!

The device is not intended to protect persons or facilities against harm. Specific

devices must be used to

guarantee safety (protection

relays

connecting switches

to the terminals J1-J6 only

switches must

is at least

twice the

maximum occurring

when measuring

250V AC switch

must be isolated

housing!

the instrument

in the presence of explosive or

flammable substances!

carrying hazardous

voltages must be secured

with external

mounting bracket

all guarantee and warranty.

Note: the measurement inputs of the device can carry life

-threatening

hazardous voltages must not be connected

The device must not be used as the only protective device or protective

carefully before operating the device!

The device is not intended to protect persons or facilities against harm. Specific

relays

, off-switches, etc).

switches must

be used

maximum occurring

measurement

must be isolated

for at

flammable substances!

with external

Summary of content (7 pages)

PAGE 1
Digalox DPM72-AV Instruction manual (Rev-2015-04) Package contents: Panel meter Digalox DPM72, 5x jumpers, 1xx mounting bracket 1. Intended use • Indoor use non condensing, condensing non corrosive. • Panel mounting. • Failure to comply with these instructions will void all guarantee and warranty. 2.
PAGE 2
3. Description The measuring modes Volt olt AC/DC, Ampere, mpere, frequency and 5A current transformer are supported. Scale endpoint of the indicator as well as scaling of the analogue signal and current transformer measurement can be adjusted freely via the DIP switch, alternatively the option for automatic adaption of the scale endpoint can be used. The unit can be switched between volt and ampere measurement via an external switch.
PAGE 3
4. Electrical Connections The device may only be operated in one of the connection options shown below. Fuse 250mA 10-24V Us Us Ilow Fuse 250mA 10-24V Us Us Supply Supply DPM72 AV/P DPM72 AV/P Voltage and current direct measurement Voltage direct, current via current transformer Measurement inputs Measurement inputs Ihigh max. 10A Uhigh Load Ulow Ilow Ihigh Uhigh max. 500V max. 500V +/L -/N Ulow Current Load +/L -/N transformer 5.
PAGE 4
Configuration via DIP switches and jumpers if it is required to switch between multiple measurement modes via an external switch (Save mode) The required measurement modes are configured and saved sequentially. 1. Connect supply voltage. 2. Set DIP-switch 10, 11 and 12 to OFF position. 3. Set the measurement mode with jumpers at J4-J6 according to table "Measurement mode”, column “Save mode". 4. Set DIP switch 10 to ON position. 5.
PAGE 5
Table common switch combinations Value 10 Combination (DIP switch 1-9) ON Value Combination (DIP switch 1-9) Value 50 200 ON 1 2 3 4 5 6 7 8 9 10 11 12 20 250 ON 1 2 3 4 5 6 7 8 9 10 11 12 100 ON 1 2 3 4 5 6 7 8 9 10 11 12 ON 1 2 3 4 5 6 7 8 9 10 11 12 25 ON 1 2 3 4 5 6 7 8 9 10 11 12 100 ON Combination (DIP switch 1-9) 1 2 3 4 5 6 7 8 9 10 11 12 500 ON 1 2 3 4 5 6 7 8 9 10 11 12 ON 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 12 Table measurement mode Measurement mode V
PAGE 6
. Other settings The following functions can be activated independently by short-circuiting short connectors J1-J3 by jumper or switch during operation: Graphical historic data display To activate the graphical historic data display connector J1 is shorted. The unit displays the stored values within the set time base as a graphical trend. The time base can be set to days (7, 14), hours (6, 12, 24, 48, 72) or minutes (3, 15, 30, 60).
PAGE 7
. Mounting Carefully insert the instrument into the panel cutout. Insert the mounting bracket from the back and push towards the panel until instrument sits tight. Make sure the mounting bracket is snapped into the side of the housing. To ensure IP65 protection (dust and water jet) when mounting in a front panel, use optional gasket. 8.