Manualshelf

User manual

ManualsBrandsTDK-LAMBDA ManualsLaboratory & Bench PSUs19" bench PSU (adjustable voltage) 0 - 20 Vdc 0 - 250 A 1 x RS232, RS485, Ethernet
11121314151617181920
10
CHAPTER 2 SPECIFICATIONS
1.Vout voltage programming
2.Iout voltage programming (*13)
3.Vout resistor programming
4.Iout resistor programming (*13
5.On/off control
6.Output current monitor (*13)
7.Output voltage monitor
8.Power supply OK signal
9.Parallel operation
10.Series operation
11.CV/CC indicator
12.Enable/Disable
13.Local/Remote analog control
14.Local/Remote analog indicator
)
2.5 ANALOG PROGRAMMING AND MONITORING
---
---
---
---
---
---
---
---
---
---
---
---
---
---
0~100%, 0~5V or 0~10V, user selectable. Accuracy and linearity: +/-0.5% of rated Vout.
0~100%, 0~5V or 0~10V, user selectable. Accuracy and linearity: +/-1% of rated Iout.
0~100%, 0~5/10Kohm full scale, user selectable. Accuracy and linearity: +/-1% of rated Vout.
0~100%, 0~5/10Kohm full scale, user selectable. Accuracy and linearity: +/-1.5% of rated Iout.
By electrical Voltage: 0~0.6V/2~15V or dry contact, user selectable logic.
0~5V or 0~10V, user selectable. Accuracy: +/-1%.
0~5V or 0~10V, user selectable. Accuracy : +/-1%.
4~5V-OK, 0V-Fail. 500ohm series resistance.
Possible , up to 4 units in master/slave mode with two wires current balance connection.
Possible (with external diodes), up to 2 units. 600Vdc max.from chassis ground.
Open collector. CC mode: On, CV mode: Off. Maximum voltage : 30V, maximum sink current: 10mA
Dry contact. Open: Off, Short: On. Max. voltage at Enable/Disable in: 6V.
By electrical signal or Open/Short: 0~0.6V or short: Remote, 2~15V or open: Local.
Open collector. Local: Open, Remote: On. Maximum voltage: 30V, maximum sink current: 10mA.
2.1 OUTPUT RATING
1.Rated output voltage(1*)
2.Rated output current (*2)
3.Rated output power
V
A
W
MODEL
GEN
8-600
8
600
4800
10-500
10
500
5000
16-310
16
310
4960
20-250
20
250
5000
30-170
30
170
5100
40-125
40
125
5000
60-85
60
85
5100
80-65
80
65
5200
100-50
100
50
5000
150-34
150
34
5100
200-25
200
25
5000
300-17
300
17
5100
400-13
400
13
5200
500-10
500
10
5000
600-8.5
600
8.5
5100
10
2.2 INPUT CHARACTERISTICS
3-Phase, 200V models:
3-Phase, 400V models:
---
---
%
0.94 @200/380Vac, rated output power.
3-Phase, 200V models: 170~265Vac, 47~63Hz
3-Phase, 400V models: 342~460Vac, 47~63Hz
3-Phase 200V models: Less than 50A
3-Phase 400V models: Less than 20A
V
8
10
16
20
30
60
40 150
200
300
500
100
80
600
400
21
10.5
22
11
22
11
22
12
22
11
22
11
22
11
22
11
22
11
22
11
22
11
22
11
22
11
22
11
22
11
3.Power Factor (Typ)
4.Efficiency (*4)
5.Inrush current (*5)
2.Maximum
Input current
at 100% load
1.Input voltage/freg. (*3)
---
A
83
84
84
86
88
86
88
88
90
88
88
88
88
88
88
8
10
16
30
20
40
60
80
150
100
200
300
400 500
600
2.3 CONSTANT VOLTAGE MODE
1.Max. Line regulation (*6)
2.Max. Load regulation (*7)
3.Ripple and noise (p-p , 20MHz) (*8)
4.Ripple r.m.s., 5Hz~1MHz
5.Temperature coefficient
6.Temperature stability
7.Warm-up drift
8.Remote sense compensation/wire
9.
11.Transient response time
12.Hold-up time (Typ)
Up-prog. response time, 0~Vomax.(*9)
10.Down-prog. response time
Full load(*9)
No load(*10)
V
---
---
mV
mV
---
---
V
mS
PPM/ C
o
mS
mS
mS
0.01% of rated output voltage
0.015% of rated output voltage +5mV
75
8
70
10
75
8
75
10
70
8
80
15
120
20
200
60
300
70
350
70
450
100
70
10
70
8
90
15
200
45
50PPM/ C from rated output voltage, following 30 minutes warm-up.
O
0.01% of rated Vout over 8 hrs interval following 30 minutes warm-up. Constant line, load & temp.
Less than 0.05% of rated output voltage +2mV over 30 minutes following power on.
2
2
2
2
5
5
5
5
5
5
5
5
5
65
135
5
80
170
5
100
200
15
30
50
400
500
600
700
80
800
900
100
50
1000
1200
1500
2000
2500
3000
3000
3000
Time for output voltage to recover within 0.5% of its rated output for a load change 10~90% of rated output
current. Output set-point: 10~100%, Local sense.
Less than 1mS, for models up to and including 100V. 2mS, for models above 100V.
5mSec Typical. Rated output power.
V
8
10
16
20
40
30
60
80
100
150
300
400
500
600
200
2.4 CONSTANT CURRENT MODE
1.Max. Line regulation (*6)
2.Max. Load regulation (*11)
3.Load regulation thermal drift
4.Ripple r.m.s. 5Hz~1MHz (*12)
5.Temperature coefficient
6.Temperature stability
7.Warm-up drift
---
---
---
---
---
mA
PPM/ C
o
0.05% of rated output current
0.1% of rated output current
70PPM/ C from rated output current, following 30 minutes warm-up.
0.01% of rated Iout over 8hrs interval following 30 minutes warm-up. Constant line, load & temperature.
O
Less than 0.1% of rated output current over 30 minutes following load change.
1600
1000
700
1700
180
350
50
50
120
80
50
20
10
10
15
8~16V model: Less than +/-0.5% of rated output current over 30 minutes following power on.
20V~600V model: Less than +/-0.25% of rated output current over 30 minutes following power on.