Datasheet

ManualsBrandsTE Connectivity - AMP ManualsConnectorsCrimp Socket, 24 ... 20AWG, Tin

108

36034

Product

Specification

11 Mar 11 Rev

Commercial Single Line, High Voltage, LGH Connector

a TE Connectivity Ltd. Company

| Indicates Change

*Trademark

For latest revision, visit out website at www.te.com/documents

For Regional Customer service, visit our website at www.te.com

1 of 6

TE logo is a trademark. Other products, logos, and company names might be trademarks of their respective owners. LOC B

1. SCOPE

1.1. Content

This specification covers the performance, tests and quality requirements for a family of commercial

single line high voltage LGH* connectors. The connectors are designed for industrial environments.

These connectors cover three operating dc and ac voltage ranges, 10, 20 and 30 kvdc and 4, 8 and 12

kvac (rms) 60 Hertz respectively.

1.2. Qualification

When tests are performed on the subject product line, the procedures specified in 109-Series Test

Specifications shall be used. All inspections shall be performed using the applicable inspection plan

and product drawing.

2. APPLICABLE DOCUMENTS

The following documents form a part of this specification to the extent specified herein. In the event of

conflict between the requirements of this specification and the product drawing, the product drawing

shall take precedence. In the event of conflict between the requirements of this specification and the

referenced documents, this specification shall take precedence.

2.1. TE Connectivity (TE) Documents

A. 109-1: General Requirements for Test Specifications

B. 109 Series: Test Specifications as indicated in Figure 1.

C. 108-10015: Contact Stamped and Formed Type XI

D. 108-10037: Contact Stamped and Formed Type XII

E. 108-10042: Contact Stamped and Formed Type III+

F. 114-10002: Application Specification

G. 501-117: Test Report

3. REQUIREMENTS

3.1. Design and Construction

Product shall be of the design, construction and physical dimensions specified on the applicable

product drawing.

3.2. Material and Finish

A. Insulating housing and cap: Polyester, glass filled, UL94V-0

B. O ring: Silicone rubber

C. Contacts

1. Type III+, Copper alloy, tin plated

2. Type XI, Copper alloy, tin plated

3. Type XII, Copper, tin plated

3.3. Ratings

A. Current: See Figure 5 for applicable current carrying capability

B. Voltage: 10, 20 and 30 kvdc

C. Temperature: -15ø to 85°C

Summary of content (6 pages)

PAGE 1
08-36034 Product Specification 11 Mar 11 Rev A Commercial Single Line, High Voltage, LGH Connector 1. SCOPE 1.1. Content This specification covers the performance, tests and quality requirements for a family of commercial single line high voltage LGH* connectors. The connectors are designed for industrial environments. These connectors cover three operating dc and ac voltage ranges, 10, 20 and 30 kvdc and 4, 8 and 12 kvac (rms) 60 Hertz respectively. 1.2.
PAGE 2
108-36034 3.4. Performance and Test Description The product is designed to meet the electrical, mechanical and environmental performance requirements specified in Figure 1. All tests are performed at ambient temperature unless otherwise specified. 3.5.
PAGE 3
108-36034 Test Description Requirement ENVIRONMENTAL See Note. Thermal Shock Humidity-Temperature Cycling NOTE Procedure 100 megohms final insulation resistance and DWV between connector and ground. See Figure 5 at sea level and 1500 feet for test voltage. Subject mated to 5 cycles between -15° and 85°C; Test Specification 109-22. Subject mated connectors insulation resistance and to 10 humidity-.
PAGE 4
108-36034 3.7. Retention of Qualification Test or Examination Examination of Product Termination Resistance, Specified Current Dielectric Withstanding Voltage Insulation Resistance Mating Force Separating Force Thermal Shock Humidity-Temperature Cycling NOTE Test Group (a) 1 2 Test Sequence (b) 1, 8 1, 7 3, 6 3, 7 2, 6 2 4 4 5 5 (c) (a) See Para 4.1.A. (b) Numbers indicate sequence in which tests are performed. (c) Precondition samples with 10 cycles durability. Figure 3 4.
PAGE 5
108-36034 4.5. Quality Conformance Inspection The applicable quality inspection plan will specify the sampling acceptable quality level to be used. Dimensional and functional requirements shall be in accordance with the applicable product drawing and this specification. Type Contact XI III+ XII NOTE Wire Size AWG Test Current amperes 20 22 16 18 20 24 12 14 16 4.0 3.0 13 10 7.5 3.0 23* 17 13 Resistance, milliohms maximum initial 11.0 11.5 6.5 7.5 9.0 14.5 1.4 1.7 2.
PAGE 6
108-36034 Figure 6 Termination Resistance Measurements Points Typical Figure 7 Separating Force Gage Pin Rev A 6 of 6