User Manual

ManualsBrandsTE Connectivity - AMP ManualsConnector ToolsHand Crimp Tool, 18 ... 14 AWG

Instruction Sheet

408--8547

LOC B

1 of 4

. 2014 TE Connectivity Ltd. family of companies

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.

TOOLING ASSI STANCE CENTER 1- - 800 - -722- -1111

PRODUCT INFORMATION 1--800--522--6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com

14 JAN 14 Rev LCERTI- CRIMP* II Straight Action Hand Tools

1. INTRODUCTION

The CERTI--CRIMP II Straight Action Hand Tools are designed to crimp a variety of loose piece terminals.

Refer to http://tooling.te.com/data.asp “Documentation” -- “Data Sheets” for a list of loose piece terminals that may be crimped by the

CERTI--CRIMP II Straight Action Hand Tool. The website also contains instructions in various languages.

The wire crimper bottoms against the anvil before the ratchet releases. This is a design feature that assures maximum electrical and

tensile performance of the crimp. Do NO T re--adjust the ratchet.

http://tooling.te.com/data.asp “Documentation”--“Data Sheets”

1. INTRODUCTION

Les pinces à action directe CERTI--CRIMP II permettent de sertir différents types de cosses en vrac.

La liste complète des cosses en vrac sertissables à l’aide de la pince à action directe CERTI--CRIMP II est consultable sur le

site http://tooling.te.com/data.asp “Documentation” -- “Data Sheets” Ce site comporte également des instructions dans

différentes langues.

Le poinçon du fil vient en butée contre l’enclume avant le déblocage de la crémaillère CERTI--CRIMP. Cette fonctionnalité

permet d’assurer des performances de sertissage optimales tant sur le plan électrique que sur celui de la tenue en traction du

fil. NE PAS retoucher au réglage de la crémaillère.

http://tooling.te.com/data.asp“Documentation” --“Data Sheets”

1. EINFÜHRUNG

Die CER TI--CRIMP II Handzange ist dazu vorgesehen, unterschiedliche Klemmen zu crimpen.

Siehe http://tooling.te.com/data.asp “Documentation” -- “Data Sheets” für eine Aufstellung von LP--Kontakte, die mit der

CERTI--CRIMP Handzange gecrimpt werden können. Die Website enthält auch Anleitungen in verschiedenen Sprachen.

Das Werkzeugoberteil fährt immer auf Block mit den Amboß, bevor die CERTI--CRIMP Handzange die Ratsche freigibt. Dies

ist ein Konstruktionsmerkmal, welches maximale Verpressung und Zugfestigkeit des Crimp--Kontaktes gewährleistet. Die

Ratsche darf nicht verstellt werden.

1. INTRODUZIONE

Gli attrezzi manuali CERTI--CRIMP II Straight Action sono progettati per aggraffare vari tipi di terminali sciolti.

Per la lista dei terminali sciolti che possono essere aggraffati con l’attrezzo manuale CERTI--CRIMP II Straight Action,

consultare il sito multilingua

http://tooling.te.com/data.asp “Documentation” -- “Data Sheets”.

Prima del rilascio del cricchetto, la matrice di aggraffatura è appoggiata sull’incudine. Tale condizione garantisce prestazioni ottimali

dell’aggraffatura in termini di elettricità e tensione. NON modificare la regolazione del cricchetto.

ORIGINAL INSTRUCTI O NS

NOTE

CAUTION

REMARQUE

ATTENTION

ANMERKUNG

VORSICHT

NOTA

ATTENZIONE

Summary of content (4 pages)

PAGE 1
Instruction Sheet CERTI- CRIMP* II Straight Action Hand Tools 408-- 8547 14 JAN 14 Rev L The CERTI--CRIMP II Straight Action Hand Tools are designed to crimp a variety of loose piece terminals. NOTE Refer to http://tooling.te.com/data.asp “Documentation” - “Data Sheets” for a list of loose piece terminals that may be crimped by the CERTI--CRIMP II Straight Action Hand Tool. The website also contains instructions in various languages.
PAGE 2
408- 8547 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume applications. A wide selection of powered application equipment for extended-- use, production operations is available. Insulation Adjustment Knob(Shown in Position 1) 3. CRIMPING PROCEDURE Front of Tool Refer to the table at http://tooling.te.com/data.
PAGE 3
408- 8547 To determine the proper insulation crimp setting, test crimp a loose piece contact using the setting that corresponds to the insulation diameter: (1) small, (2) and (3) medium, or (4) large. If the crimped insulation barrel is too tight or loose, change the setting by pulling out and rotating the adjustment knob to the desired setting. 2. Close tool handles until ratchet releases and then allow them to open freely.
PAGE 4
08- 8547 4. Hold the wire in place and squeeze the handles until the ratchet releases. Hold the handles in this position, maintaining just enough tension to keep the dies closed. 5. Check the clearance between the bottoming surfaces of the wire crimper and the wire anvil. See Figure 1. If the clearance is 0.025 mm [.001 in.] or less (on at least two of the bottoming surfaces), the ratchet is satisfactory. If clearance exceeds 0.025 mm [.001 in.], the ratchet is out of adjustment and must be repaired.