Data Sheet

ManualsBrandsTE Connectivity ManualsConnectorsTE Connectivity Socket enclosure - cable AMP-Superseal 1.5mm Series Total number of pins 2 Contact spacing: 6 mm 0-28208

Product

Specification

108-20090

Rev. C1

Description.

AMP SUPERSEAL 1,5 SERIES CONNECTORS

REVISED M.G. 22/01/2008 R.M. 31/01/2008

REVISED AND REDRAWN M.G. 24/11/2007 R.M. 25/11/2007

rev letter rev. record DR Date CHK Date

DR. DATE

APVD DATE

A.BRUNI SEP. ‘91

This specification is a controlled

document.

This information is confidential and is

disclosed to you on condition that no

further disclosure is made by you to other

than AMP personnel without written

authorization from AMP Italia.

Page 1 of 14

* Trademark of AMP Incorporated

LOC I

FTEC174 rev. 1 - July 99

AMP SUPERSEAL 1,5 SERIES CONNECTORS

Product Code: 0933 GPL: 444

Summary of content (14 pages)

PAGE 1
Product Specification 108-20090 Rev. C1 Description. AMP SUPERSEAL 1,5 SERIES CONNECTORS AMP SUPERSEAL 1,5 SERIES CONNECTORS Product Code: 0933 C1 C GPL: 444 REVISED M.G. 22/01/2008 R.M. 31/01/2008 REVISED AND REDRAWN M.G. 24/11/2007 R.M. 25/11/2007 DR Date rev letter DR. A.BRUNI This specification is a controlled document. * Trademark of AMP Incorporated FTEC174 rev. 1 - July 99 rev. record DATE APVD SEP. ‘91 A.
PAGE 2
108-20090 1.0 SCOPE: This specification covers the requirements for products performance, test methods and quality assurance provisions of following products: FEMALE CONNECTORS (Housings assemblies for receptacle contacts, 1 to 6 positions, with NR.
PAGE 3
108-20090 REQUIREMENTS: 2.0 DESIGN AND CONSTRUCTION: Product shall comply with the design, construction and physical dimensions specified in the applicable product drawing. 2.1 MATERIALS: Components Material Receptacle contacts: Phosphor Bronze Contacts Tab contacts: Brass Finish, for contacts only PreTin plated Housings / Sec. Lock PA 6.6, Glassfiber filled / Radial Sealing / Single wire seals Liquid silicone rubber / 2.2 RATINGS: A. Current Rating : 14A max. with 1,5 mm² wire B.
PAGE 4
108-20090 3.0 TEST REQUIREMENTS AND PROCEDURES SUMMARY: FEATURES 3.1 Voltage Drop TEST CONDITIONS (mated connectors) Between two points on wires at 1cm from the housing edges. LIMITS ≤ 3 mV/A on new contacts. The voltage drop of wire must be subtracted Test currents: 6A for 0,5sqmm wire 11A for 1,0sqmm wire 14A for 1,5sqmm wire 3.2 Contact resistance (mated contacts) ≤ 3 mΩ on new contacts. Between the ends of crimps. Test current: 10mA 3.
PAGE 5
108-20090 FEATURES 3.7 Single contact engaging force 3.8 Single contact disengaging force 3.9 Retention force of the single contact in the housings 3.10 Crimping Tensile Strength 3.11: Corrosion Test 3.11a Salt spray corrosion TEST CONDITIONS LIMITS Engage single rec.ctc. onto tab counterpart using a free floating fixture with a rate of 25100mm/min of travel speed (tab as shown in Fig.1) ≤ 8N Separate single rec.ctc.
PAGE 6
108-20090 FEATURES 3.12 Water resistance: Static immersion TEST CONDITIONS LIMITS Mated connectors subjected to 5 cycles composed of: -Insulation resistance: ≥200MΩ - 30 min. in oven at +125°C -No leakage detected to a visual examination - 30 min. immersed in water with 5% of NaCl under a pressure of 0,01bar at a temperature of 23°C 3.13 Water resistance: Dynamic immersion 3.
PAGE 7
108-20090 FEATURES 3.16 Thermal cycling 3.17 Ageing resistance TEST CONDITIONS Mated connectors subjected to: - 14 cycles composed of: • 16 hours at +40°C, 95% r.h. • 2 hours at -40°C • 2 hours at +125°C • 4 hours at +23°C (max.time to change condition: 3min.) - exposure for 24 hours at +40°C and 95% r.h. - 10 mating and unmating operations - No damages - Insulation resistance and dielectric withstanding resistance as above specified.
PAGE 8
108-20090 FEATURES 3.20 Vibration Test 3.21 High temperature resistance with current load 3.22 Current overload TEST CONDITIONS Mated connectors placed on a platform as per Fig.3, subjected to vibrations with following parameters: - Frequency: 10 - 500 - 10Hz - Speed of frequency variation: 1octave/min. - Displacement: 0,75mm for frequencies below 70Hz.
PAGE 9
108-20090 GROUPS AND SEQUENCE NUM. TEST DESCRIPTION 3.0 VISUAL EXAMINATION 3.1 VOLTAGE DROP 4, 9 3.2 CONTACT RESISTANCE INSULATION RESISTANCE DIELECTRIC WITHSTANDING VOLTAGE CONNECTOR MATING FORCE CONNECTOR UNMATING FORCE CTC. ENGAGING FORCE CTC. DISENGAGING FORCE CONTACT RETENTION IN HSG. CRIMP TENSILE STRENGHT SALT SPRAY CORROSION KESTERNICH CORROSION STATIC IMMERSION 5, 1 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11a 3.11b 3.12 3.13 DYNAMIC IMMERSION 3.14 IP X6K TEST 3.15 IP X9K TEST 3.
PAGE 10
8-20090 TEST TAB DIMENSIONS FIG. 1 Rev. C1 Page 10 of 14 LOC I FTEC174 rev.
PAGE 11
108-20090 DYNAMIC IMMERSION TEST SETUP FIG. 2 Rev. C1 Page 11 of 14 LOC I FTEC174 rev.
PAGE 12
108-20090 VIBRATION TEST SETUP FIG. 3 Rev. C1 Page 12 of 14 LOC I FTEC174 rev.
PAGE 13
108-20090 IP X6K TEST SETUP FIG. 4 Rev. C1 Page 13 of 14 LOC I FTEC174 rev.
PAGE 14
108-20090 IP X9K TEST SETUP FIG. 5 Rev. C1 Page 14 of 14 LOC I FTEC174 rev.