Information

ManualsBrandsTE CONNECTIVITY ManualsD-SUB ConnectorsD-SUB pin strip 180 ° Number of pins: 9 Print AMPLIMITE HD-20 1 pc(s)

Product

Specification

108-1092

11Mar11 Rev F

AMPLIMITE* HD-22 Front Metal Shell, PCB Mounted Connector

1. SCOPE

1.1. Content

This specification covers performance, tests and quality requirements for AMPLIMITE* HD-22 right

angle and vertical printed circuit board mounted connectors.

1.2. Qualification

When tests are performed on the subject product line, procedures specified in Figure 1 shall be used.

All inspections shall be performed using applicable inspection plan and product drawing.

1.3. Qualification Test Results

Successful qualification testing on the subject product line was completed on 14Dec89. The

Qualification Test Report number for this testing is 501-104. Additional testing was completed on

09Jan02, the Engineering Report number for this testing 502-1125. This documentation is on file at and

available from Engineering Practices and Standards (EPS).

2. APPLICABLE DOCUMENTS

The following TE Connectivity (TE) documents form a part of this specification to the extent specified

herein. Unless otherwise specified, the latest edition of the document applies. In the event of conflict

between the requirements of this specification and the product drawing, the product drawing shall take

precedence. In the event of conflict between the requirements of this specification and the referenced

documents, this specification shall take precedence.

! 109-1: Test Specification (General Requirements for Test Specifications)

! 109 Series: Test Specifications as indicated in Figure 1

! 114-40021: Application Specification (AMPLIMITE* HD-22 Right Angle Front Metal Shell

Connectors)

! 114-40022: Application Specification (AMPLIMITE* HD-22 Straight Front Metal Shell PC Board

Connector)

! 501-104: Qualification Test Report (AMPLIMITE* HD-22 Front Metal Shell, PCB Mounted

Connector)

! 502-1125: Engineering Report (AMPLIMITE* HD-22 Front Metal Shell, PCB Mounted Connector)

3. REQUIREMENTS

3.1. Design and Construction

Product shall be of design, construction and physical dimensions specified on applicable product

drawing.

3.2. Materials

Materials used in the construction of this product shall be as specified on the applicable product

drawing.

a TE Connectivity Ltd. Company

| Indicates change

*Trademark

For latest revision, visit our website at www.te.com/documents.

For Regional Customer Service, visit our website at www.te.com

1 of 8

TE logo is a trademark. Other products, logos, and company names might be trademarks of their respective owners. LOC B

Summary of content (8 pages)

PAGE 1
Product Specification 108-1092 11Mar11 Rev F AMPLIMITE* HD-22 Front Metal Shell, PCB Mounted Connector 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for AMPLIMITE* HD-22 right angle and vertical printed circuit board mounted connectors. 1.2. Qualification When tests are performed on the subject product line, procedures specified in Figure 1 shall be used. All inspections shall be performed using applicable inspection plan and product drawing. 1.3.
PAGE 2
108-1092 3.3. Ratings ! ! ! 3.4. Voltage: • UL: 250 volts Ac • CSA: 125 volts AC Current: • Right angle: 2 amperes maximum per contact • Straight posted: 1.5 amperes maximum per contact Temperature: • Regular housing: -55 to 105°C • High temperature housing: -55 to 130°C Performance and Test Description Product is designed to meet electrical, mechanical and environmental performance requirements specified in Figure 1.
PAGE 3
108-1092 Test Description Requirement Procedure Physical shock. No discontinuities greater than 1 microsecond. See Note. TE Spec 109-26-1. Subject mated connectors to 50 G's half-sine shock pulses of 11 milliseconds duration. 3 shocks in each direction applied along 3 mutually perpendicular planes, 18 total shocks. See Figure 4. Mating force. Force in pounds maximum. Grounding Indents Size Positions W/O With 1 15 5.6 33 2 26 9.8 38 3 44 16.5 46 4 62 23.3 52 5 78 29.3 58 TE Spec 109-42, Condition A.
PAGE 4
108-1092 Test Description Requirement Procedure Humidity-temperature cycling. See Note. TE Spec 109-23-3, Condition B. Subject mated connectors to 10 humidity-temperature cycles between 25 and 65°C at 95% RH. Mixed flowing gas. See Note. TE Spec 109-85-3. Subject mated connectors to environmental class III for 20 days. Temperature life. See Note. TE Spec 109-43. Subject mated connectors to temperature life at 105°C for 500 hours.
PAGE 5
108-1092 4. QUALITY ASSURANCE PROVISIONS 4.1. Qualification Testing A. Sample Selection Connector housings and contacts shall be prepared in accordance with applicable Instruction Sheets and shall be selected at random from current production. Test groups 1 and 3 shall consist of 5 samples each of 30 µin gold plating and gold flash of a right angle receptacle connector.
PAGE 6
108-1092 4.2. Requalification Testing If changes significantly affecting form, fit or function are made to the product or manufacturing process, product assurance shall coordinate requalification testing, consisting of all or part of the original testing sequence as determined by development/product, quality and reliability engineering. 4.3. Acceptance Acceptance is based on verification that the product meets the requirements of Figure 1.
PAGE 7
108-1092 Figure 3 Termination Resistance Measurement Points Rev F 7 of 8
PAGE 8
108-1092 Figure 4 Vibration & Physical Shock Mounting Fixture Rev F 8 of 8