Datasheet

ManualsBrandsTE CONNECTIVITY ManualsPCB ConnectorsPin enclosure - PCB Mini-Universal-MATE-N-LOK Total number of pins 12 1 pc(s)

Application Specification

114--16017

LOC B

1 of 12

E2011 T yco Electronics Corporation, a TE Connectivity Ltd. Company

TE logo is a trademark.

*Trademark. Other product names, logos, or company names might be trademarks of their respective owners.

TOOLING ASSISTANCE CENTER 1 --800 --722 --1111

PRODUCT INFORMATION 1--800--522--6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com

Mini-Universal MATE-N-LOK* Connectors

17 MAR 11 Rev L

All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and

inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2_.

Figures and illustrations are for identification only and are not drawn to scale.

1. INTRODUCTION

This specifi cation covers the requirements for application of Mini--Universal MATE--N--LOK connectors for

free--hanging, panel--mount, and printed circuit (pc) board applications. These connectors provide a reliable

and economic means of groupi ng multiple--lead connections in computers, computer/peripheral equipment,

business machines, entertainment centers, and appliances.

The connectors are available in hermaphroditi c housing and positively polarized: plug housing, vertical pin

header , right--angle pin header, and cap housing. The housings accept socket contacts and pin contacts.

Each contact features a contact stop to ensure proper insertion depth of the contact in the contact cavity of the

housing. The contacts are available in strip form for machine application and loose piece for manual tooling

application.

The hermaphroditic housing is availabl e with 2, 3, or 4 circuits for free--hanging applications. The cap housi ng

is avail able in 1, 2, or 3 circuits for free--hanging application and 2, 3, 4, 6, 9, 12, or 15 circuits for panel

mounting or free--hanging application.

The plug housing and vertical pin header is available w ith 2, 3, 4, 6, 8, 9, 10, 12, 14, 15, 16, 18, 20, 22, or 24

circuits; the vertical bli nd--mate pin header is available in 4, 6, 8, 9, 10, 12, or 15 circuits for panel mounting or

free--hanging application. The right--angle pin header is available in 2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, or

24 circui ts for pc board application.

To avoid personal injury, these connectors are not to be used for inter rupting current.

When corresponding with personnel, use the terminology provided in this specification to facilitate your

inquiries for information. Basi c terms and features of this product are provi ded i n Fi gure 1.

Figure 1

Locking

Latch

Locking

Tab

Mounting

Ear

Right- Angle Pin Header

Cap Housing

Plug Housing Vertical Pin Header

Boardlock

Solder

Tine

Standoff

Pin ContactSocket Cont act

Insulation

Barrel

Wire

Barrel

Locking

Lance

Contact

Stop

Solder

Tine

Hermaphroditic Housing

Locking

Latch

Locking

Tab

NOTE

DANGER

Summary of content (12 pages)

PAGE 1
Application Specification 114-- 16017 Mini- Universal MATE- N- LOK* Connectors NOTE i 17 MAR 11 Rev L All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2_. Figures and illustrations are for identification only and are not drawn to scale. 1.
PAGE 2
114-- 16017 2. REFERENCE MATERIAL 2.1. Revision Summary Revisions to this application specification include: S Updated application specification to corporate requirements S Added DANGER to Section 1 and CAUTION to Paragraph 3.3 S Added hermaphroditic housing to Figure 1 and contact stop to Section 1, Figures 1 and 10, and Paragraph 3.2,C S Replaced superceded hand crimping tools in Section 5, and added NOTE to Paragraph 5.1 2.2.
PAGE 3
114-- 16017 3.2. Contact Crimp Requirements A. Carrier Cutoff There shall be no burrs on the cutoff tab. The carrier cutoff tab length shall not exceed the dimension given in Figure 2. B. Crimp Height The insulation barrel shall be formed around but not cut into the wire insulation. The wire barrel and insulation barrel crimp height and width is given in Figure 2. NOTE i The applied crimp dimension (within the function range of the product) is dependent on the termination tooling being used.
PAGE 4
114-- 16017 AUTOMATIC MACHINE WIRE (Stranded Only) SIZE (AWG) INSULATION DIAMETER WIRE BARREL CRIMP HEIGHT +0.05 [+.002] 30 WIDTH INSULATION BARREL CRIMP WIDTH (Ref) 1.06 [[.042] 042] 1.78 [[.070] 070] 1.22 [[.048] 048] 2.03 [[.080] 080] 1.57 [.062] 2.79 [.110] 1.78 [.070] 3.56 [.140] 0.50 [.020] 0.88--1.27 [.035--.050] [ 035-- 050] 28 26 26 0.55 [.022] 0.60 [.024] D0.63 [.025]D 1.20--1.75 [ 047-- 069] [.047--.069] 24 22 0.69 [.027] 0.78 [.031] 22 0.81 [.032] 20 18 22 (2 Wires) 1.
PAGE 5
114-- 16017 G. Wire Barrel Seam The wire barrel seam shall be closed adequately to confine all strands of the wire. There shall be no loose strands. Wire strands should not be embedded in the outside of the wire barrel. H. Straightness The contact, including the cutoff tab, shall not be bent above or below the datum line more than the amount shown in Figure 3. I. Twist and Roll There shall be no twist or roll in crimped portion that will impair usage of the contact. See Figure 3.
PAGE 6
114-- 16017 Cap Housing Panel Cutout 1.6 [.063] A B C 3.4 [.132] 5.4 [.211] D PANEL DIMENSION CAP HOUSING NUMBER OF CIRCUITS A B C D 02 10.69 [.421] 06.15 [.242] 2.49 [.098] 10.34 [.407] 03 10.69 [.421] 06.15 [.242] 4.60 [.181] 14.55 [.573] 04 14.91 [.587] 10.34 [.407] 2.49 [.098] 10.34 [.407] 06 19.10 [.752] 14.55 [.573] 2.49 [.098] 10.34 [.407] 09 19.10 [.752] 14.55 [.573] 12 23.29 [.917] 18.74 [.738] 4.60 [.181] [ ] 14.55 [.573] [ ] 15 27.43 [1.080]0 22.96 [.
PAGE 7
114-- 16017 Vertical Pin Header 9--, 12--, and 15--Circuit, Matrix 14--, 16--, 18--, 20--, 22--, and 24--Circuit, Dual Row 1.40¦0.08 Dia 4.44 [.175] [.055¦.003] Dia Typ 3.18 [.125] Dia 4.44 [.175] 4.14 [.163] Typ 1.40¦0.08 Dia [.055¦.003] Dia Typ 3.18 [.125] Dia Typ 4.14 [.163] Typ 4.14 [.163] Typ 4.14 [.163] Typ 4.14 [.163] Typ Right- Angle Pin Header 2--Circuit 2.070 [.081] 3--Circuit 2.070 [.081] « 1.40¦0.08 [.055¦.003] « 1.40¦0.08 [.055¦.003] 0 « 0.13 [.005] M 2 Plc « 3.86¦0.05 [.152¦.
PAGE 8
114-- 16017 14-- and 18--Circuit 4.14 [.163] 8.28 [.326] 12.42 [.489] 16.56 [.652] 0 4.14 [.163] 8.28 [.326] 12.42 [.489] 16.56 [.652] « 1.40¦0.08 [.055¦.003] 4.14 [.163] « 0.13 [.005] M 18 Plc 7.34 [.289] 5.33 [.210] « 3.86¦0.05 [.152¦.002] 2 Plc 8.280¦0.064 [.326¦.003] 2 Plc 22--Circuit 0 4.14 [.163] 8.28 [.326] 12.42 [.489] 4.14 [.163] 8.28 [.326] 12.42 [.489] 16.56 [.652] 20.70 [.815] 16.56 [.652] 20.70 [.815] 4.14 [.163] « 1.40¦0.08 [.055¦.003] « 0.13 [.005] M 22 Plc 7.34 [.289] 5.
PAGE 9
114-- 16017 3.6. Soldering A. Flux Selection The solder tines must be fluxed prior to soldering with a mildly active, rosin base flux. Selection of the flux will depend on the type of pc board and other components mounted on the board. Additionally, the flux must be compatible with the wave solder line, manufacturing, health, and safety requirements. Call the PRODUCT INFORMATION at the number at the bottom of page 1 for consideration of other types of flux.
PAGE 10
114-- 16017 SOLDERING PROCESS Wave Soldering MAXIMUM WAVE TEMPERATURE CELSIUS FAHRENHEIT TIME (At Max Temperature) 260 500 5 Seconds Figure 8 3.7. Mating and Unmating A. Polarization The connectors (excluding hermaphroditic) are fully polarized (ribs and slots) to provide proper mating using a positive locking mechanism to prevent accidental disengagement of mated connectors. B. Keying Keying plugs provide additional polarization for mating connectors.
PAGE 11
4-- 16017 Hand Crimping Tool (Typ) (Refer to Table) Heavy Duty Miniature Quick Change Applicator (Refer to Table) (408--8040) AMPOMATOR CLS Lead--Making Machines 122500--[ ] (409--5852) or 356500--[ ] (409--5878) WIRE Insertion Tool 91002--1 (408--7347) AMP--O--LECTRIC Model “G” Terminating Machine 354500--[ ] (409--5842) APPLICATOR POWER UNIT SIZE (AWG) INSULATION DIAMETER 30 0.88--1.52 [.035--.060] 567418--1 122500--2, --3 or 356500--1, --2 28, 26 0.88--1.52 [.035--.
PAGE 12
114-- 16017 6. VISUAL AID The illustration below shows a typical application of Mini--Universal MATE--N--LOK connectors. This illustration should be used by production personnel to ensure a correctly applied product. Applications which DO NOT appear correct should be inspected using the information in the preceding pages of this specification and in the instructional material shipped with the product or tooling.