Datasheet

2
12-2017, Rev. 1217
www.te.com
© 2017 TE Connectivity.
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
Automotive Relays
Plug-in Maxi ISO Relays
Power Relay F7
(Continued)
Insulation Data
Initial dielectric strength
between open contacts 500V
rms
between contact and coil 500V
rms
between adjacent contacts 500V
rms
Load dump test
ISO 7637-1 (12VDC), test pulse 5 V
s
=+86.5VDC
ISO 7637-2 (24VDC), test pulse 5 V
s
=+200VDC
Other Data
EU RoHS/ELV compliance compliant
Protection to heat and fire according UL-94 HB or better
8)
Ambient temperature -40 to 125°C
Climatic cycling with condensation
EN ISO 6988 6 cycles, storage 8/16h
Temperature cycling,
IEC 60068-2-14, Nb 10 cycles, -40/+85°C (5°C/min)
Damp heat cyclic,
IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temp. 55°C
Damp heat constant, IEC 60068-2-3, Ca 56 days
Category of environmental protection,
IEC 61810 RTI – dustproof
Degree of protection, IEC 60529 IP54 (dustproof)
Corrosive gas
IEC 60068-2-42 10±2cm
3
/m
3
SO
2
, 10 days
IEC 60068-2-43 1±0.3cm
3
/m
3
H
2
S, 10 days
Vibration resistance (functional)
IEC 60068-2-6 (sine sweep) 10 to 500Hz, min. 5g
8)
Other Data (continued)
Shock resistance (functional)
IEC 60068-2-27 (half sine) 6ms, min. 30g.
9)
Drop test, free fall
IEC 60068-2-32 1m onto concrete
Terminal type plug-in, QC/ PCB
Cover retention
pull force 150N
push force 200N
Terminal retention
pull force 150N
push force 150N
resistance to bending 10N
10)
force applied to side 10N
10)
torque 0.3Nm
Weight approx. 38g (1.3oz)
Resistance to soldering heat THT
IEC 60068-2-20 260°C, 10s
Packaging unit
plug-in: 210 pcs.
plug-in with bracket: 208 pcs.
PCB 315 pcs.
08) Refers to used materials.
09) No change in the switching state >10μs. Valid for NC contacts, NO contact values
significantly higher.
10) Values apply 2mm from the end of the terminal. When the force is removed, the
terminal must not have moved by more than 0.3mm.
Accessories
For details see datasheet Connectors for Maxi ISO Relays
NO
1 form A, NO
87
30
86
85
NOR
1 form A, NO with resistor
87
3086
85
NOD
1 form A, NO with diode
87
3086
85
Terminal Assignment
Quick connect terminal similar to ISO 8092-1
24.9 ±0.3
16 ±0.5
6 ±0.4
15 ±0.1
4 ±0.2
17 +1/-0.5
11 ±0.5
0.8 ±0.05
ø 1.7 +0.2
1.2 ±0.05
9.5 ±0.1
6.3 ±0.1
25.9 ±0.3
25.9 ±0.3
5.3 ±0.1
TE1098-Y1
0.3
4x
Measurement
reference plane
Dimensions
Power Relay F7 with quick connect terminals similar to ISO 8092-1 View of the terminals (bottom view)
TE1103-411