MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors Table of Contents Introduction This catalog has been designed to assist you, our customer, identify products to satisfy your connector needs for printed circuit board headers, mass termination connectors preloaded with contacts, crimp-snap contacts and housings, and card edge connectors with preloaded contacts.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors Table of Contents (Continued) Crimp SL-156 Crimp AMP EP Connectors Need more information? Call Technical Support at the numbers listed below. Technical Support is staffed with specialists well versed in Tyco Electronics products. They can provide you with: ■ Technical support ■ Catalogs ■ Technical Documents ■ Product Samples ■ Authorized Distributor Locations MTA-156 Card Edge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-50 IDC Connectors and Headers Product Facts ■ ■ ■ ■ ■ ■ .503 [12.78] or .254 [6.45] ■ Max. Vertical Max. Right-Angle Component Recognized by Underwriters Laboratories Inc. to US and Canadian Standards, File No. E28476 (Connectors and Headers) File No. E53793 (Ribbon Cable) These matrixes have been prepared to assist you in defining the correct mating halves for the MTA-50 header and connector kit combination.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-50 IDC Connectors and Headers (Continued) Feed-Thru and Closed End Connectors Receptacle Assemblies — Ribbon Cable MTA-50 .050 [1.27] ± .004 A [± 0.10] (See Note 1) .315 ± .006 [8.00 ± 0.15] .150 [3.81] Material and Finish Housing — UL 94V-2 rated, thermoplastic Contacts — Phosphor bronze; .000100 [0.00254] min. tin in wire termination area, over .000050 [0.00127] min. nickel; choice on mating end: .000100 [0.00254] min. tin or .
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-50 IDC Connectors and Headers (Continued) MTA-50 .050 [1.27] Connector Kits — Ribbon Cable (Continued) .068 2 Plcs. [1.73] Strain Relief Covers Material and Finish .040 2 Plcs. [1.02] Strain Relief Cover — UL 94V-0 rated, thermoplastic, black .090 4 Plcs. [2.29] Feed-Thru A .237 ± .008 [6.02 ± 0.20] .123 ± .006 [3.12 ± 0.15] Feed-Thru Closed End .255 [6.48] A .237 ± .008 [6.02 ± 0.20] Closed End Feed-Thru and Closed End No.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-50 IDC Connectors and Headers (Continued) Feed-Thru and Closed End Connectors Receptacle Assemblies — Discrete Wire ± .004 [± 0.10] (See Note 1) MTA-50 .050 [1.27] A .315 ± .006 [8.00 ± 0.15] .150 [3.81] Material and Finish Housing — UL 94V-2 rated, thermoplastic Contacts — Phosphor bronze; .000100 [0.00254] min. tin in wire termination area, over .000050 [0.00127] min. nickel; choice on mating end: .000100 [0.00254] min. tin or .
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-50 IDC Connectors and Headers (Continued) MTA-50 .050 [1.27] Connector Kits — Discrete Wire (Continued) .068 2 Plcs. [1.73] Strain Relief Covers Material and Finish .040 2 Plcs. [1.02] Strain Relief Cover — UL 94V-0 rated, thermoplastic, black .090 4 Plcs. [2.29] Feed-Thru A .237 ± .008 [6.02 ± 0.20] .123 ± .006 [3.12 ± 0.15] Feed-Thru Closed End .255 [6.48] A .237 ± .008 [6.02 ± 0.20] Closed End Feed-Thru and Closed End No.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-50 IDC Connectors and Headers (Continued) Through-Hole Header Assemblies Vertical Circuit #1 MTA-50 .050 [1.27] Note: To determine header overall length (dim. A), multiply .050 x the number of circuits and add .150. Example: .050 x 6 circuits equals .300 + .150 = .450 [11.43]. .035 [0.89] Ref. .170 [4.32] A .220 ± .003 [5.59 ± 0.08] .060 [1.52] .125 [3.18] Ref.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-50 IDC Connectors and Headers (Continued) MTA-50 .050 [1.27] Surface Mount Header Assemblies Note: To determine header overall length (dim. A), multiply .050 x the number of circuits and add .150. Example: .050 x 6 circuits equals .300 + .150 = .450 [11.43]. .035 Ref. [0.89] Vertical Circuit #1 .170 [4.32] A .220 ± .003 [5.59 ± 0.08] .249 Ref. [6.32] .028 ± .001 Typ. [0.71 ± 0.03] .100 Typ. [2.54] .050 Typ. [1.27] .100 .162 [2.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors .100 [2.54] Centerline MTA-100 IDC Connectors and Headers Product Facts ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ R ■ R Technical Documents Product Specification 108-1050 MTA-100 Connectors Application Specifications 114-1019 MTA-100 Connectors 114-1031 MTA-100 Ribbon Cable Assembly MTA-100 .100 [2.54] ■ Connectors and headers for 2 through 28 positions; wire sizes of 22, 24, 26 and 28 AWG [0.4-0.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-100 Connector/Header Mateability Guide This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-100 header and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-100 Connector/Header Mateability Guide (Continued) This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-100 header and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating. Matrix for .000030 [0.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-100 IDC Connectors—Closed End and Feed-Thru Material and Finish Closed End Connectors MTA-100 .100 [2.54] Housing — UL94V-2 rated, nylon, see below for color; or UL94V-0 rated, nylon, black Contacts — Phosphor bronze, post tin plated, .000030 [0.00076] or .000015 [0.00038] post gold-plated over nickel .275 [6.99] .275 [6.99] Color Coding by Wire Size for UL94V-2 Connectors 28 AWG — Green 26 AWG — Blue 24 AWG — White 22 AWG — Red A .
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-100 IDC Connectors—Closed End and Feed-Thru (Continued) Connector Ordering Information Base Part Numbers Closed End No. of Pos.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-100 IDC Connector Accessories Covers Closed End Strain Relief Covers Strain Relief Cover — UL94V-2 rated, nylon, white Dust Covers — UL94V-0 rated, polyester, white MTA-100 .100 [2.54] .345 [8.76] .127 [3.23] Material (RoHS Compliant) Closed End Dust Covers .335 [8.51] Retention Dimple .340 [8.64] A .360 [9.14] .105 [2.67] .130 [3.3] A Note: This portion of the front locking bar may or may not be present.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-100 IDC Connector Accessories (Continued) Keying Plug with Carrier Strip (10 plugs per strip) Part No. 641994-1 .027 Sq. [0.69] .038 [0.97] .300 [7.62] Material (RoHS Compliant) MTA-100 .100 [2.54] UL94V-2 rated, nylon, natural color .065 [1.65] .077 [1.96] Note: Removal of contact is not necessary when using keying plug. .125 [3.18] .500 Ref. [12.7] 1.800 Ref. [45.72] Replacement IDC Contacts AWG mm 22 24 26 28 0.3–0.4 0.2 0.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-100 Posted Connector/Connector Mateability Guide This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-100 posted connector and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-100 Posted Connector/Connector Mateability Guide (Continued) This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-100 posted connector and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating. Matrix for .000030 [0.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-100 IDC Posted Connectors (Wire-to-Wire)—Closed End, Feed-Thru Closed End Material and Finish Feed-Thru Housing — UL 94V-2 rated, nylon, see chart for color Contacts — Copper alloy, post tin or gold plated over nickel (see chart) B Dim. B Dim. MTA-100 .100 [2.54] Notes: 1. Mating half visuals - pages 14 & 15. 2. Use feed thru strain relief covers & feed thru dust covers (if needed) - page 16. 3.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-100 Flat Headers—Straight and Right-Angle Material and Finish Straight Post (.025 [0.64] Square) Right-Angle Post (.025 [0.64] Square) Housing — UL94V-0 rated, polyester, white Posts — Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel .200 [5.08] .200 [5.08] A .025 [0.64] Sq. .100 [2.54] .050 Typ. [1.27] Typ. Post No. 1 A .100 [2.54] .295 [7.49] .025 [0.64] Sq. .140 [3.56] Ref. .100 [2.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-100 Narrow Flat Headers—Straight and Right-Angle Material and Finish Straight Post (.025 [0.64] Square) Right-Angle Post (.025 [0.64] Square) Housing — UL94V-0 rated, polyester, white Posts — Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel MTA-100 .100 [2.54] Notes: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-100 Polarized Headers—Straight and Right-Angle Material and Finish Straight Post (.025 [0.64] Square) Housing — UL94V-0 rated, polyester, white Posts — Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel .225 [5.72] .225 [5.72] .125 [3.18] .125 [3.18] A A .100 [2.54] Typ. .025 [0.64] Sq. .035 Min. [0.89] Post No. 1 .295 [7.49] .295 [7.49] .290 [7.37] .535 [13.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-100 Friction Lock Headers—Straight and Right-Angle Material and Finish Straight Post (.025 [0.64] Square) MTA-100 .100 [2.54] Housing — UL94V-0 rated, polyester, white Posts — Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel Right-Angle Post (.025 [0.64] Square) .225 [5.72] .225 [5.72] Notes: 1. Post(s) can be omitted for keying purposes.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors Page_Head (Continued) MTA-100 Headers with Retention Peg—Straight Friction Lock Material and Finish .113 [2.87] Housing — UL94V-0 rated, thermoplastic, black Posts — Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel .250 [6.35] For mateability options, see matrix on pages 12 and 13. For mating half visuals, see pages 14, 15 and 31. Post No. 1 .135 [3.43] .025 ± .001 [0.64 ± 0.03] Square Typ. No. of Pos.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-100 .100 [2.54] MTA-100 High Profile Headers—Right-Angle Material and Finish Friction Lock Polarized Housing — UL94V-0 rated, thermoplastic, black Posts — Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel Right-Angle Post (.025 [0.64] Square) Right-Angle Post (.025 [0.64] Square) A Notes: 1. Post(s) can be omitted for keying .250 purposes. Specify the desired [6.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors Page_Head (Continued) MTA-100 Polarized High Temperature Headers—Straight and Right-Angle Material and Finish For use with Infrared Reflow Process Notes: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail. 3. To determine header overall length (dim. A) multiply .
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-100 Friction Lock High Temperature Headers—Straight and Right-Angle For use with Infrared Reflow Process Material and Finish MTA-100 .100 [2.54] Housing — 2–12 Position — UL94V-0 rated, nylon, black 13–18 Position — UL94V-0 rated, LCP, black Posts — Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel Notes: 1. Post(s) can be omitted for keying purposes.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-100 Polarized and Friction Lock Surface Mount Headers—Straight Material and Finish For use with Infrared Reflow Process Notes: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail. 3. To determine header overall length (dim. A) multiply .100 x the number of posts. Example: .
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-100 Shrouded Headers—Straight and Right-Angle Material and Finish Straight Post (.025 [0.64] Square) Housing — UL94V-0 rated, polyester, black Posts — Copper alloy, tin plated; or .000030 [0.00076] gold over nickel Post No. 1 Post No. 1 Notes: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2. Headers with .000015 [0.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors .100 [2.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors CST-100 II Shrouded Headers—Straight and Right-Angle Material and Finish Straight Post (.025 [0.64] Square) Right-Angle (.025 [0.64] Square) Housing — UL94V-0 rated, polyester, black Posts — Copper alloy, tin plated; or .000030 [0.00076] gold over nickel Post No. 1 Post No. 1 CST-100 II .100 [2.54] Notes: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors .156 [3.96] Centerline MTA-156 IDC Connectors and Headers Product Facts Connectors and headers for 2 through 24 positions; wire sizes of 18, 20, 22, 24 and 26 AWG [0 .9– 0.
Matrix for Tin Plated Part Numbers Connectors MTA-156 .156 [3.96] This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-156 header and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 Connector/Header Mateability Guide (Continued) This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-156 header and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 IDC Connectors—Closed End Material and Finish Closed End with Locking Ramp Housing — UL94V-2 rated, nylon, see below for color; or UL94V-0 rated, nylon, black Contacts — Phosphor bronze, post tin plated, .000030 [0.00076] or .000015 [.00038] post gold plated over nickel .245 [6.22] .050 [1.27] .725 [18.42] .156 Typ. [3.96] without Polarizing Tabs .100 [2.54] .258 [6.56] All Wire Sizes in UL94V-0 — Black Notes: 1.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 IDC Connectors—Closed End (Continued) Connector Ordering Information Base Part Numbers The “Base Part Numbers” Chart at right shows the base part number and number of circuits available for the described connectors. Base number 640426 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-640426-0 All part numbers in bold face are the RoHS equivalent version. Example: No. of Pos.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 IDC Connectors—Feed-Thru Material and Finish Feed-Thru with Locking Ramp Housing — UL94V-2 rated, nylon, see below for color; or UL94V-0 rated, nylon, black Contacts — Phosphor bronze; post tin plated, .000030 [.00076] or .000015 [.00038] post gold plated over nickel .245 [6.22] A .100 [2.54] .097 [2.46] .385 .325 [9.78] [8.26] .050 [1.27] .725 [18.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 IDC Connectors—Feed-Thru (Continued) Connector Ordering Information Base Part Numbers The “Base Part Numbers” Chart at right shows the base part number and number of circuits available for the described connectors. Base number 640599 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-640599-0 The part numbers in bold face are the RoHS equivalent version. Example: No. of Pos.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 Connector Accessories Closed End Covers Strain Relief Covers Dust Covers Retention Dimple .335 [8.51] Material (RoHS Compliant) .440 [11.18] Strain Relief Covers — UL94V-2 rated, nylon, white Dust Covers — UL94V-0 rated, polyester, white .440 [11.18] .335 [8.51] .127 [3.23] .105 [2.67] .130 [3.30] A A MTA-156 .156 [3.96] Base Part Numbers Closed End Strain Relief Dust Covers Covers Cover No. of Cover No. of Part Nos.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 Connector Accessories (Continued) Replacement IDC Contacts .125 [3.18] Wire Size AWG mm2 Material and Finish Contacts — Phosphor bronze, post tin plated; .000030 [0.00076] or .000015 [0.00038] post gold plated over nickel .637 [16.18] 18 20 22 24 26 Note: Tyco Electronics does not recommend terminating an MTA contact more than one time. Use replacement contacts when required for field repairs or wire changes. 0.8–0.9 0.5–0.6 0.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 Connector Accessories (Continued) Keying Plugs Material (RoHS Compliant) Loose Piece Part No. 640629-1 (Flush) Used with keyed headers UL94V-2 rated, nylon, natural color Note: Removal of contact is not necessary when using keying plug. On Carrier Strip Part No. 641623-1 (Flush) (10 per strip) .300 [7.62] .066 [1.68] .500 [12.70] Ref. .065 [1.65] .051 [1.30] .085 [2.16] Flush 2.525 [64.14] Ref. MTA-156 .156 [3.96] Part No.
6414 35 6414 36 6414 37 6414 38 6414 39 6415 22 6415 23 6415 24 6415 25 6415 26 MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 Posted Connector/Connector Mateability Guide Matrix for Tin Plated Part Numbers Connectors Y Y Y Y Y N N N N N Y Y Y Y Y N N N N Y Y Y Y Y N N N N N Y Y Y Y Y N N N N Y Y Y Y Y N N N N N Y Y Y Y Y N N N N Y Y Y Y Y N N N N N Y Y Y Y Y N N N N Y Y Y Y Y N N N N N Y Y Y Y Y N N N N Y Y Y Y Y N N N N N Y Y Y Y Y N N N N Y Y Y Y Y N N N N N Y Y Y Y Y N N
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 Posted Connector/Connector Mateability Guide (Continued) This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-156 posted connector and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating. Matrix for .000030 [0.00076] Gold Plated Part Numbers Connectors MTA-156 .156 [3.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 IDC Posted Connectors (Wire-to-Wire)—Closed End, Feed-Thru Material and Finish Closed End 4 Housing — UL 94V-2 rated, nylon, see chart for color Contacts — Copper alloy, post tin or .000030 [.00076] gold plated over nickel Feed-Thru 3 B Dim. 1 2 B Dim. A Dim. .105 [2.67] ± .010 [ ± 0.25 ] 1.010 [25.65] A Dim. .105 [2.67] ± .010 [ ± 0.25 ] 1.010 [25.65] .156 [3.96] .156 [3.96] .487 .355 [12.37] [9.02] Ref. .370 [9.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 Flat Headers—Straight Material and Finish Housing — UL94V-0 rated, polyester, white Posts — Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel .250 [6.35] .125 [3.18] A MTA-156 .156 [3.96] Notes: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 Flat Headers—Right-Angle Material and Finish Housing — UL94V-0 rated, polyester, white Posts — Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel Post No. 1 .125 [3.18] .125 [3.18] .390 [9.91] Solder tail Length (See Chart) Edge of Board .390 ± .015 [9.91 ± 0.38] X .156 [3.96] .080/.070 [2.03/1.78] .125 [3.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 Friction Lock Headers—Straight .180 [4.57] Material and Finish Housing — UL94V-0 rated, polyester, white Posts — Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel MTA-156 .156 [3.96] Notes: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 Friction Lock Headers—Right-Angle Material and Finish Housing — UL94V-0 rated, polyester, white Posts — Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel .180 [4.57] .300 [7.62] Y = .068 [1.73] Max. 2-8 position tin plated and 2–24 position gold plated headers. Notes: For mateability options, see matrix on pages 34, 35, 54 and 58.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 Polarized Lock Headers—Straight Material and Finish Housing — UL94V-0 rated, polyester, white Posts — Copper alloy, tin plated or .000030 [0.00076] gold over nickel .210 [5.33] 90° Ref. Typ. Retention Tabs 4 Plc. Notes: MTA-156 .156 [3.96] 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 Polarized Lock Headers—Right-Angle Material and Finish Housing — UL94V-0 rated, polyester, white Posts — Copper alloy, tin plated or .000030 [0.00076] gold over nickel For mateability options, see matrix on pages 34, 35, 54 and 58. For mating half visuals, use only connectors with a locking ramp for polarization/retention purposes, see pages 36 thru 39, 55, 60 and 62. For polarizing purposes only use connectors without a locking ramp.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 Friction Lock High Temperature Headers—Straight Material and Finish For use with Infrared Reflow Process Housing — UL94V-0 rated, nylon, black Posts — Copper alloy, tin plated, .000015 [0.00038] gold over nickel Temperature— Maximum Temperature Rating: 280°C A Notes: MTA-156 .156 [3.96] 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 Shrouded Headers—Straight and Right-Angle Straight Post (.045 [1.14] Square or Round) Material and Finish Housing — UL94V-0 rated, polyester, black Posts — Copper alloy, tin plated; or .000030 [0.00076] or .000015 [0.00038] gold over nickel For mateability options, see matrix on pages 34, 35, 54 and 58. For mating half visuals, see pages 36 thru 39 and 55.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 IDC Quad Connectors ■ Provides four points of contact ■ Greater current carrying capability than Standard MTA-156 Connectors ■ Connector styles include both closed end and feedthru with locking ramp, with and without polarizing tabs in 2 through 12 positions ■ Available for wire ranges of 18 – 22 AWG [0.9– 0.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 IDC Quad Connectors—Closed End and Feed-Thru Closed End with Locking Ramp A .097 [2.46] .090 [2.29] .280 .230 [7.11] [5.84] .100 [2.54] .325 .355 [8.26] [9.02] AWG .180 [4.57] .156 Typ. [3.96] .245 [6.22] .100 [2.54] .308 [7.82] AWG .725 [18.42] without Polarizing Tabs with Polarizing Tabs Feed-Thru with Locking Ramp .245 [6.22] A .090 [2.29] .230 .280 [5.84] [7.11] .325 .385 [8.26] [9.78] AWG .180 [4.57] .156 Typ.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 IDC Card Edge Connectors—Closed End and Feed-Thru Material and Finish C B A Housing — UL94V-0 rated, polyester, see chart for color Contacts — Phosphor bronze, post tin plated .161 Ref. [4.09] .156 [3.96] Typ. .094 [2.39] .170 [4.32] Note: Refer to pages 70 thru 74 for approved wire listings. MTA-156 .156 [3.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA-156 IDC Card Edge Accessories Dust Cover Retention Dimple Material (RoHS Compliant) UL94V-0 rated, polyester, white .530 [13.46] Cover is for both Closed End and Feed-Thru connectors .130 [3.3] A Cover Ordering Information MTA-156 .156 [3.96] The “Base Part Numbers” Chart at right shows the base part number and number of circuits available for the described cover.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors .156 [3.96] Centerline SL-156 Crimp Contacts and Housings SL-156 .156 [3.96] Product Facts ■ Rugged wire-to-board interconnection to mate with .045 square or round post headers or staked posts on .156 centers ■ Standard Connectors accept wire range of 18–24 AWG [0.9–0.2 mm✒] and LID Connectors accept wire range of 18–24 AWG [0.9–0.2 mm✒] and a limited 16 AWG [1.29–1.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors SL-156 Crimp Contacts and Keying Plugs Contacts .180 [4.57] .115 [2.92] Material and Finish .012 [0.3] bright tin plated brass or phosphor bronze; .012 [0.3] pre-tin brass; or .012 [0.3] brass or phosphor bronze with .000030 [0.00076] gold over nickel (see chart) ■ ■ ■ .121/.115 [3.07/2.92] .131 ±.004 [3.33 ±0.10] A High Force (6.5 Amp Max.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors SL-156 Housings—Wire-to-Board .660 [16.76] Housings A Material (RoHS Compliant) UL94V-0 rated, nylon, white .076 [1.93] Typ. .097 [2.46] .250 [6.35] Notes: 1. Accepts either .045 [1.14] square or round posts. Housings mate with flat and friction lock headers, or staked posts on .156 [3.96] centers. 1 2 23 24 .037 Ref. [0.93] (A) With Locking Ramp/With Polarizing Tabs 2.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors SL-156 Housings With Through Board Latch Housings Material (RoHS Compliant) UL94V-2 rated, nylon, white .156 [3.96] Typ. .078 [1.98] Typ. 1 .075 [1.91] 2 3 4 7 8 9 10 .250 [6.35] .050 ± .007 [1.27 ± 0.18] ± .003 ± 0.08 ] SL-156 .156 [3.96] .063 [1.60 .125 [3.18] .063 ± .003 [1.60 ± 0.08] .660 [16.76] A Mates with .045 square or round staked posts only. For contacts, see page 59 . 10 9 8 7 4 3 2 1 B .105 [2.67] .
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors SL-156 Housings and Contacts for Large Insulation Diameter (LID) Wire Housings UL 94V-0 rated, nylon, white Notes: 1. Accepts Standard and LID contacts. 2. Larger opening in housings eases contact insertion when using wires that have large insulation diameters (.100-.112 [2.54-2.84]). 3. Housings are not End-to-End stackable. .660 [16.76] .156 Typ. [3.96] Material (RoHS Compliant) .054 [1.37] Typ. .095 Typ. [2.41] .100 [2.54] .250 [6.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors AMP Economy Power (EP) Wire-to-Board Connector System Product Facts .156 [3.96], .200 [5.08] and .312 [7.92] centerline ■ Wire-to-board connectors comprised of plug housings, receptacle contacts for discrete wire, and mating post headers ■ Hooded contact designed to accept wire with insulation diameters up to .118 [3.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors AMP Economy Power (EP) Wire-to-Board Connector System (Continued) Contacts and Plug Housings, Low-Profile Crimp, Snap-in Receptacle Contacts .083 [2.11] Material and Finish (RoHS Compliant) See chart. .362 [9.19] .055 [1.40] .08 [2.1 Related Product Data Plug Housings — Pages 64, 67 and 69 AMP EP .156 [3.96] Wire Size Range AWG mm2 Wire Insulation Diameter 18–22 0.89-0.30 .067-.118 1.70-3.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors AMP Economy Power (EP) Wire-to-Board Connector System (Continued) Straight and Right-Angle Low-Profile Post Headers .156 [3.96] Typ. Straight .078 [1.98] Typ. Edge of Board A .156 [3.96] Centerline .190 [4.82] .028 [0.7] .335 [8.5] .268 [6.8] Material and Finish (RoHS Compliant) Housing — UL 94V-0 rated natural color Note: Alternate colors available upon request. Minimums may apply.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors AMP Economy Power (EP) Wire-to-Board Connector System (Continued) Straight and Right-Angle Low-Profile Post Headers, High Temperature Straight Maximum Temperature Rating: 280°C A Edge of Board .190 [4.82] .156 Typ. [3.96] Housing — UL 94V-0 rated nylon, high temperature, natural color Note: Alternate colors available upon request. Minimums may apply. Please contact product engineer or product manager for details. Post — Tin-plated brass .
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors AMP Economy Power (EP) Wire-to-Board Connector System (Continued) Plug Housings and Post Headers .406 [10.30] A Plug Housings .200 [5.08] Centerline Material and Finish (RoHS Compliant) Housing — UL 94V-0 rated nylon, natural color Note: Alternate colors available upon request. Minimums may apply. Please contact product engineer or product manager for details. Related Product Data Contacts — Page 64 Mating Post Headers — See below .263 [8.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors AMP Economy Power (EP) Wire-to-Board Connector System (Continued) Straight Post Headers, Low-Profile .312 [7.92] Centerline .063 +.004/-0 Dia. Punched Hole [1.60 +0.1/-0] A Material and Finish (RoHS Compliant) .028 [0.7] Housing — UL 94V-0 rated natural color Note: Alternate colors available upon request. Minimums may apply. Please contact product engineer or product manager for details. Post — Tin-plated brass .065 +.004/-0 Dia.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors AMP Economy Power (EP) Wire-to-Board Connector System (Continued) Plug Housing and Post Header, High-Profile 1 Position Plug Housing Part Number 1-1123823-1 .571 [14.5] .150 [3.8] .207 [5.3] .244 [6.2] .169 [4.3] .224 [5.7] Material and Finish (RoHS Compliant) Housing — UL 94V-0 rated nylon, natural color Note: Alternate colors available upon request. Minimums may apply. Please contact product engineer or product manager for details. .
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA Wire Selection Proper wire selection is critical to the success of a wire-toboard application. The chart identifies wires that have been evaluated and approved by the product engineering section. If you plan to use a wire not on the approved list, please submit a sample 12" length of wire to Tyco Electronics for evaluation. AWG Metric Equivalents 18 —0.8 –0.9 mm2 20 —0.5 –0.6 mm2 22 —0.3 –0.4 mm2 24 —0.2 mm2 26 —0.12 –0.15 mm2 28 —0.08 –0.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors IDC Ribbon Cable Product Facts ■ Compatible with a variety of Insulation Displacement Connectors ■ Available on .025 [0.63], .0394 [1.00], .050 [1.27], .100 [2.54] and .156 [3.96] centerline ■ Color code edge mark on conductor #1 ■ Gray flame retardant flexible PVC insulation ■ Insulation rated for temperature of -20°C to +105°C ■ Recognized under the Component Program of Underwriters Laboratories Inc., File No. E53793 R The .100 [2.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors .100 [2.54] Centerline, IDC Ribbon Cable, PVC Insulation Product Specifications B Voltage Rating — 300 Volts UL Recognized — AWM Style 2651 CSA — Available on request A .050 [1.27] Typ. C .010 [0.25] .100 [2.54] Typ. Edge Mark IDC Ribbon Cable No. of Conductors Dimensions B A Part Number C Insulation — Gray Flame Retardant Flexible PVC .007 [0.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors .156 [3.96] Centerline, Flat Ribbon Cable, PVC Insulation Product Specifications B Voltage Rating — 300 Volts UL Recognized — AWM Style 2651 CSA — Available on request A .078 [1.98] Typ. C .010 [0.25] .156 [3.96] Typ. Edge Mark No. of Conductors A Insulation — Gray Flame Retardant Flexible PVC .007 [0.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors Prepared IDC Ribbon Cable In addition to bulk cable, the US Engineering Cable Assembly Group offers Prepared Cable for the .100 [2.54] and .156 [3.96] centerline cables. This can be in the form of prenotched cable on reels or cut-tolength cable segments. IDC Ribbon Cable Prenotched 250 foot reels of cable can be produced with notches at varying increments or repeating all along the cable.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA Wire Termination Flowchart Choose the appropriate MTA Connector from the MTA Catalog 82056. Select the proper wire style and AWG for the chosen MTA Connector (Refer to pages 70-74). Choose the MTA Termination Tooling (Refer to pages 76-79). Terminate the Wire-to-MTA Connector per Application Tooling Instruction Sheet. Inspect the MTA Wire Termination per Application Specification, especially the wire depth.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA Application Tooling Options Note: Max. Insulation Outside Diameter Wire: .060 [1.52] for MTA-100 Connectors /.095 [2.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA Application Tooling Options (Continued) One-At-A-Time Termination Tooling (Typical Tooling Combinations) Manual Hand Tool with Interchangeable Head Air Hand Tool with Interchangeable Head Air Bench Mount Tool with Interchangeable Head and Foot Switch Electric Bench Machine with Interchangeable Head Power Units Manual Hand Tool — Pistol Grip Handle Part No. 58074-1 ■ ■ ■ Air Hand Tool — Pistol Grip Pneumatic Handle Part No.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA Application Tooling Options (Continued) Mass Termination Tooling (Typical Tooling Combinations) Manual Bench Tool with Applicator and Holding Fixture Air Harness Tool with Applicator Air Bench Machine 2700 lb Air Bench Machine with Ribbon Cable Notcher Assembly Power Units Manual Bench Tool — Arbor Frame Assembly Part No.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors MTA Application Tooling Options (Continued) The following is a list of technical documents covering the installation, operation, adjustment, maintenance and repair of MTA application tooling. Technical Documents Instruction Sheets (IS) provide instructions for assembling or applying the product. They are intended for the Manufacturing Assembler or Operator.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors Part Number Index Note: This index lists all cataloged parts by base no. only. Complete part nos. (with prefixes and/or suffixes) are shown on the page(s) indicated. Part Number Index Part No.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors Part Number Index (Continued) Page 57 39 39 39 39 39 39 39 39 39 39 15 15 15 15 45 45 45 45 45 45 45 45 45 45 42 45 45 45 45 45 42 15 15 15 15 59 42 17 17 17 17 15 15 15 15 17 40 40 16 16 15 15 15 15 15 37 37 37 37 37 15 Part No.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors Part Number Index (Continued) Part No. 647125 647126 647127 647128 647131 647132 647133 647134 647135 647136 647139 647140 647141 647142 647143 647144 647166 647167 647168 647295 647296 647297 647298 647299 647300 647400 647401 647402 647406 647409 647466 647476 647477 Page 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 53 29 29 29 28 28 28 27 27 27 62 62 62 62 62 62 45 15 Part No.
Global Contacts Americas Argentina – Buenos Aires Phone: +54-11-4733-2200 Fax: +54-11-4733-2211 Brasil – São Paulo Phone: +55-11-2103-6000 Fax: +55-11-2103-6030 Canada – Toronto Phone: +905-475-6222 Fax: +905-474-5520 Product Information Center: Phone: +905-470-4425 Fax: +905-474-5525 Chile – Santiago Phone: +56-2-345-0361 Fax: +56-2-223-1477 Colombia – Bogota Phone: +57-1-319-8959 Fax: +57-1-319-8960 Mexico – Mexico City Phone: +52-55-1106-0800 +01-800-733-8926 Fax: +52-55-1106-0901 For Latin/South Ame
Tyco Electronics Corporation Harrisburg, PA 82056–10K–MS–FP–6-08–OG3B
