Information

ManualsBrandsTE CONNECTIVITY ManualsPCB ConnectorsSocket enclosure - cable Econoseal J Series Mark II (+) Total number of pins 6 1 pc(s)

Product Specification

製品規格

108

5262

22MAR2016 Rev. C8

ECONOSEAL

“

”

Mark II+ Connector

Tyco Electronics Japan G.K. (3-5-8 Hisamoto Takatsu-ku Kawasaki, 213-8535)

1 of 15

This document is subject to change. Call local TE for the latest revision.

* : Trademark

1. Scope:

1.1 Contents:

This specification covers the requirements for product performance, test methods and quality

assurance provisions of ECONOSEAL-J Mark Ⅱ

Connector.

The applicable product descriptions and part number are as follows:

Part Number Descriptions

171630

.070 Series Receptacle Contact

171662

171631

.070 Series Tab Contact

171661

NBR Bis-containing

NBR non-Bis type

Rubber Plug for .070

172746 2822352

172888 2822354

176886 2822355

178210 2822356

900324(Silicone)

900325(Silicone)

NBR Bis-containing

NBR non-Bis type

Cavity Plug for .070

172748 2822357

NBR Bis-containing

NBR non-Bis type

1-Position Plug Housing for .070 Series

174877 2822388

174878 Double Lock Plate for .070 Series 1-Position Plug Housing

174879 1-Position Cap Housing for .070 Series

174880 Double Lock Plate for .070 Series 1-Position Cap Housing

NBR Bis-containing

NBR non-Bis type

.070 Series 2-Position Plug Housing

917851 2822348

174352 .070 Series 2-Position Plug Housing

174353 Double Lock Plate for .070 Series 2-Position Plug Housing

174354 .070 Series 2-Position Cap Housing

174355 Double Lock Plate for .070 Series 2-Position Cap Housing

NBR Bis-containing

NBR non-Bis type

.070 Series 3-Position Plug Housing

174357 2822390

174358 Double Lock Plate for .070 Series 3-Position Plug Housing

174359 .070 Series 3-Position Cap Housing

174360 Double Lock Plate for .070 Series 3-Position Cap Housing

NBR Bis-containing

NBR non-Bis type

.070 Series 4-Position Plug Housing

174257 2822391

174258

Double Lock Plate for .070 Series 4-Position Plug Housing

Fig.1 (Continued)

Summary of content (15 pages)

PAGE 1
08-5262 Product Specification 製品規格 22MAR2016 Rev. C8 ECONOSEAL “J” Mark II+ Connector 1. Scope: 1.1 Contents: This specification covers the requirements for product performance, test methods and quality assurance provisions of ECONOSEAL-J Mark Ⅱ+ Connector.
PAGE 2
Product Specification Part Number 174259 174260 NBR Bis-containing NBR non-Bis type 174262 2822346 174263 174264 174265 NBR Bis-containing NBR non-Bis type 174982 2822393 174983 174984 174985 NBR Bis-containing NBR non-Bis type 174655 2822395 174656 174657 174658 NBR Bis-containing NBR non-Bis type 174661 2822638 174662 174663 174664 NBR Bis-containing NBR non-Bis type 174371 NBR Bis-containing 174372 NBR Bis-containing 174373 2822359 NBR non-Bis type 2822360 NBR non-Bis type NBR Bis-containi
PAGE 3
Product Specification 2. 108-5262 Applicable Documents: The following documents form a part of this specification to the extent specified herein. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirements of this specification and the referenced documents, this specification shall take precedence. 2.1 TE Specifications: A.
PAGE 4
Product Specification 2.
PAGE 5
Product Specification 2.3.7 108-5262 Connector: A connector is an assembly of housing and crimped wire contacts with rubber plugs loaded in all contact positions, and further equipped with double lock plate. In this product line, cap housing assembled with tab contact and plug housing assembled with both receptacle contact and seal ring are available. 3. Requirements: 3.
PAGE 6
Product Specification 3.4 108-5262 Performance and Test Descriptions: The product is designed to meet the electrical, mechanical and environmental performance requirements specified in Para. 3.5. All tests are performed at ambient temperature unless otherwise specified. 3.5 Test Requirements and Procedures Summary: Para.
PAGE 7
Product Specification Para. Test Items 108-5262 Requirements No. of Pos. Double Lock Plate Loading Force 1 2 3 4 6 8 10 12 3.5.6 Loading Force N Max. 29 39 39 39 39 59 59 59 Procedures Fix housing of the testing machine, and insert locking plate in axial direction by operating the head at a rate of 100mm approx. a minute. Measure the force required to complete loading of locking plate. Termination Resistance (Low Level) 3mΩ max. (Initial) 10mΩ max.
PAGE 8
Product Specification Para. Test Items 108-5262 Requirements Procedures Insulation Resistance 100MΩ min. (Initial) Measure by applying test potential between the adjacent contacts, and between the contacts and ground in the mated connectors. Dielectric Strength Connector must withstand test potential of 1.0kVAC for 1 minute. No physical damage shall be evident after the test.
PAGE 9
Product Specification Para. Test Items Requirements 108-5262 Procedures Housing Locking Retention Force: 98 N min. Fix mated pair of connectors on testing machine, and apply an axial separating force to one of them. Measure the force required to separate the connectors, with or without breakage of locking leg. Watertight Sealing 49kPa (4.9mN/mm2) min. (Initial) 29.4kPa (2.9mN/mm2) min. (Final) Blow compressed air into mated pair of connectors through a small hole.
PAGE 10
Product Specification Para. 3.5.19 Test Items Requirements Procedures Resistance to Liquid Detergents: Must meet the specified requirements after testing in the sequence specified in Fig.9. Immerse mated connectors into commercially suppliable car washer liquid detergent at 50±2℃ for 2 hours. After the durations, rinse in tap water for 5 minutes, and have it dried before subsequent measurement.
PAGE 11
Product Specification Para. Test Items Requirements Must meet the specified Subject mated connectors to requirements after testing in ejection of Port 1 and cement or the sequence specified in Fig.9. Kanto loam dust powder dispersed by compressed air blowing at a rate of 1.5kg per 10 seconds at every other 15 minutes for the total of 1 hour. After completion of duration, repeat mating / unmating for 3 cycles. Temperature Rising 50℃ max.
PAGE 12
Product Specification Para. Test Items Current Cycling Requirements Procedures Must meet the specified Subject mated contact to test requirements after testing in current of the intensity obtained the sequence specified in Fig.9. by Fig.6 applied for 300 cycles intermittently 45 minutes ON, 15 minutes OFF to the series wired contacts. Wire Size (mm2) 0.2 0.3 0.5 0.85 1.25 3.5.28 108-5262 Test Current (DC A) 7 9 11 14.5 18.5 No. of Positions 1 2～3 4～5 6～8 9～12 Reduction Coefficient 1 0.75 0.6 0.
PAGE 13
Product Specification 108-5262 Fig.7 Fig.8 Rev.
PAGE 14
Product Specification 4.
PAGE 15
Product Specification 5. Quality Assurance Provisions: 5.1 Test Conditions: 108-5262 Unless otherwise specified all the tests shall be performed in any combination of the following test conditions. 15～35℃ 45～75％ 86.7～107KPa （650～800mmHg） Temperature Relative Humidity Atmospheric Pressure Fig.10 5.2 Sample Preparation: 5.2.1 Samples: The samples to be employed for the tests shall be prepared in accordance with 114-5082, TE Application Specification, Crimping .070 & .