Datasheet

54
MTA-156
.156 [3.96]
644329
644370
644371
644375
644376
644377
644381
644382
644383
644387
644388
644389
640389
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
640385
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
640383
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
640445
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
644611
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
644613
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Connectors
Headers
644615
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
644617
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
644749
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
644751
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
644752
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
644754
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
647123
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
647125
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
647126
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
647127
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Product Facts
Provides four points of
contact
Greater current carrying
capability than Standard
MTA-156 Connectors
Connector styles include
both closed end and feed-
thru with locking ramp, with
and without polarizing tabs
in 2 through 12 positions
Available for wire ranges of
18 22 AWG [0.9– 0.3
mm
]
Contacts are lubricated for
fretting corrosion protection
Complies with
Tyco Electronics Quality
Specification 102-6,
“Preparation of Design
Objectives”
Uses existing MTA applica-
tion tooling for termination
Quad connectors preloaded
with contacts
All contacts are slotted for
insulation displacement
(IDC) termination technique
Connectors and headers are
end-to-end stackable
AWG size is “frosted” on
the side of the connector
Recognized under the
Component Program of
Underwriters
Laboratories Inc.,
File No. E28476
Certified by Canadian
Standards
Association,
File No. LR 7189
Satisfies the VDE require-
ments according to VDE
110, Insulation Group B,
250 vac for air and creep-
age paths
R
R
The MTA-156 Quad Con-
nector provides a connec-
tion with four points of
contact. The UL94V-0 rated
connector with multi-point
contacts provides greater
current carrying capability
than the Standard MTA-156
Connector. These connec-
tors comply with
Tyco Electronics Quality
Specification 102-6* and
satisfy the VDE requirements
according to VDE 110.
The connectors are avail-
able for wire ranges of
18 22 AWG [0.9– 0.3 mm
2
]
and in a variety of styles
including closed end and
feed-thru with locking ramp,
with and without polarizing
tabs.
Only one wire to be termin-
ated into an IDC contact
slot.
*The 102-6 Quality Specification is
the new procedure for “Preparation
of Design Objectives”. Its purpose is
to provide a means for verifying the
maximum current carrying capacity
of the device.
Note: Refer to pages 70 through 74
for approved wire listings.
The MTA-156 Quad Connectors
only mate with standard MTA-
156 square post headers and
use existing MTA application
tooling for termination.
Performance Data
Voltage Rating 600 vac
Current Rating 12.5 amp max. on a
single circuit.
For Multiple Circuit Loading
refer to Product Specification for current
rating chart.
Low-Level Resistance
3.0 m max. initial
Dielectric Withstanding Voltage
1500 vac/1 min.
Insulation Resistance
5000 M min. initial
Operating Temperature
-55 C to 105 C
Technical Documents
Product Specifications
108-1219 MTA-156 Quad Connector
System
Application Specifications
114-1048 MTA-156 Quad
Connector
This matrix has been prepared to assist you, our customer,
in defining the correct mating halves for the MTA-156
header and connector combination. Where a “Y” is indi-
cated the combination is a valid mating pair.
MTA-156 IDC Quad Connectors
MTA, CST-100 II, SL-156 and
AMP Economy Power (EP) Connectors
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341