Datasheet

MULTI-CONDUCTOR 28 AWG 0.050" CENTER FLAT RIBBON CABLE
REVISION HISTORY
2 05/03/01 RL Added part number
3 01/28/03 RL Added part number
4 08/14/04 EP Revised P/N table and legend
125 Goddard Memorial Drive • Worcester, MA 01603 USA
Tel: [phone] Toll-Free: (877) MADISON Fax: [phone]
5 03/28/06 RL Added part number
Spec Number: 100-4703
6 01/02/08 DC Added part number
Part Number: See Table 1
7 06/04/08 DC Revised Mfg Location Code, Removed Footnote
Customer: AMP Prepared By:
D.M. Card
Customer #: 971111 Reviewed By:
T. Grzysiewicz B. Morissette
Page
1 of 1
Users should evaluate the suitability of this product for their application. Contact factory for latest revision of specification. Tyco Electronics reserves the right to make
changes in materials or processing, which do not affect compliance with any specification, without notification to the Buyer.
Form AP-03A Issue 9
CONSTRUCTION
Single Component
Conductor: 28 AWG 7/36 Tin Plated Copper, 0.015 Inch Diameter
Final Assembly
Core: Singles Laid Flat and Parallel (See Table 1)
Insulation/Jacket: Flame Retardant Flexible PVC, Color - Gray
Dimensions: See Table 1
Identification: Polarity Edge Mark shall cover at minimum the edge of cable to
centerline of the first conductor and shall not exceed the centerline of the
second conductor top and bottom, Color – Red
Print Legend: “` AWM STYLE 2651 105°C 300V VW-1 MADISON CABLE
(A02) CSA AWM I A 105°C 300V FT1”
TABLE 1
# of
Tyco P/N Dimensions (Inches)
Cond
100 ft
Putup
2
500 ft
Putup
3
Span B Span C
3 TBD 4-971111-0 0.100 + 0.005 / - 0 0.150 + 0.010 / - 0.005
4 TBD 3-971111-8 0.150 + 0.005 / - 0 0.200 + 0.010 / - 0.005
6 1-57040-9 1-971111-9 0.250 + 0.005 / - 0 0.300 + 0.010 / - 0.005
8 2-57040-0 2-971111-0 0.350 + 0.005 / - 0 0.400 + 0.010 / - 0.005
9 1-57040-2 1-971111-2 0.400 + 0.005 / - 0 0.450 + 0.010 / - 0.005
10 1-57040-3 1-971111-3 0.450 + 0.010 / - 0 0.500 + 0.010 / - 0.005
12 2-57040-9 3-971111-6 0.550 + 0.010 / - 0 0.600 + 0.010 / - 0.005
14 1-57040-4 1-971111-4 0.650 + 0.010 / - 0 0.700 + 0.010 / - 0.005
15 1-57040-5 1-971111-5 0.700 + 0.010 / - 0 0.750 + 0.010 / - 0.005
16 1-57040-6 1-971111-6 0.750 + 0.010 / - 0 0.800 + 0.010 / - 0.005
18 2-57040-3 2-971111-3 0.850 + 0.010 / - 0 0.900 + 0.010 / - 0.005
20 0-57040-1 0-971111-1 0.950 + 0.010 / - 0 1.000 + 0.010 / - 0.005
24 1-57040-7 1-971111-7 1.150 + 0.010 / - 0 1.200 + 0.010 / - 0.005
25 0-57040-2 0-971111-2 1.200 + 0.010 / - 0 1.250 + 0.010 / - 0.005
26 0-57040-3 0-971111-3 1.250 + 0.010 / - 0 1.300 + 0.010 / - 0.005
28 0-57040-8 3-971111-3 1.350 + 0.010 / - 0 1.400 + 0.010 / - 0.005
30 2-57040-1 2-971111-1 1.450 + 0.010 / - 0 1.500 + 0.010 / - 0.005
34 0-57040-4 0-971111-4 1.650 + 0.010 / - 0 1.700 + 0.010 / - 0.005
36 2-57040-5 2-971111-5 1.750 + 0.015 / - 0 1.800 + 0.010 / - 0.005
37 1-57040-8 1-971111-8 1.800 + 0.015 / - 0 1.850 + 0.010 / - 0.005
40 0-57040-5 0-971111-5 1.950 + 0.015 / - 0 2.000 + 0.010 / - 0.005
44 2-57040-4 2-971111-4 2.150 + 0.015 / - 0 2.200 + 0.010 / - 0.005
50 0-57040-6 0-971111-6 2.450 + 0.015 / - 0 2.500 + 0.010 / - 0.005
60 0-57040-7 0-971111-7 2.950 + 0.015 / - 0 3.000 + 0.010 / - 0.005
64 2-57040-2 2-971111-2 3.150 + 0.015 / - 0.004 3.200 + 0.016 / - 0.005
PITCH ACCUMULATION CHART
4
Number of Conductors Accumulation Range
0 - 34 ± 0.010”
34 - 64 ± 0.015”
2
Length per Reel: 100 +1/-0 ft; May Contain Separate Lengths; 20 ft Mininum per
Length, Two Lengths Maximum per Reel
3
Length per Reel: 500 + 6/-0 ft Continuous
4
Pitch Accumulation is defined as the maximum difference between the actual
accumulated pitch and the accumulated specification pitch for any group of
continuous conductors.
ELECTRICAL CHARACTERISTICS
Impedance (Gnd-Sig-Gnd): 105 Ohms Nominal @ TDR
Capacitance: 13.5 pF/ft Maximum
Time Delay: 1.45 ns/ft Maximum
Insulation Resistance: 10 Gigaohms/10 ft
Crosstalk (5 ns rise-time on 10 ft sample):
Near-End: 3.0% Maximum
Far-End: 4.0% Maximum
Conductor DC Resistance: 0.064 Ohms/ft Nominal @ 20°C
SAFETY CERTIFICATION
UL Listing: AWM Style 2651 105°C 300 Volts VW-1
CSA Certification: AWM I A 105°C 300 Volts FT1
RoHS Compliance: In Accordance to European Directive 2002/95/EC, Issue
13.2.2003
Flat Cable Cross-Section
Span C
0.025
+0.004"
-0.004"
0.008
+0.006"
-0.003"
0.035
+0.003"
-0.003"
Red Edge Mark
Span B
0.050 +/- 0.003" TYP
Note: Tolerance is + 0.006 / - 0.004" for 64 Conductor.
*
*