Datasheet

2
Pistol Grip Manual
Handle Assembly
Part Number 58074-1
A basic hand tool requires a Handle
Assembly and a Terminating Head,
ordered separately, shown on page 4.
■ Lightweight, easy to use
■ Ratchet control will not release cam
trigger until it is fully bottomed
■ Ratchet release
■ “U”-shaped key slides into handle to
hold interchangeable heads securely
■ Material (handle) — Molded nylon
For drawings or technical data, contact your Tyco Electronics sales engineer or call the Technical Support Center: 1-800-522-6752.
Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents.
Specifications subject to change. Consult Tyco Electronics for latest specifications.
Specifications
Length — 3.75 [95.2]
Width — 1.12 [28.6]
Height — 4.00 [101.6]
Grip Span — 2.50 [63.5] over
trigger/handle
Weight — 3.5 oz [99 g]
Cycle Time — 0.7 - 0.8 s
Pistol Grip Pneumatic
Handle Assembly
Part Number 58075-1
■ Lightweight
■ Power assist for less operator effort
■ Push-button trigger actuated
■ Quiet — 78 dB max.
■ “U”-shaped key slides into handle to
secure interchangeable heads
■ Material (handle) — Molded nylon
Specifications
Length — 4.88 [124]
Width — 1.13 [28.7]
Height — 6.00 [152]
Grip Span — 2.50 [63.5] over push-
button trigger/handle
Weight — 18 oz [510 g]
Air Pressure — 40 - 70 psi
[2.76 - 4.83 bar]
Air Supply Line (1) — 7 ft [2.13 m]
long, 3/16 [4.76] I.D. with 1/8 [3.18]
NPT fitting
Cycle Time — 0.7 - 0.8 s
Bench Mount
Pneumatic Power Unit
Part Number 58338-1
Assembly consists of a bench mount
with attached pneumatic power unit, a
foot switch, and two air lines which
connect the switch to the power unit and
the air source to the switch. Mounting
hardware is not included.
■ Mounting bracket allows interchange-
able heads to be pointed up or down
to suit operator
■ Power assist for greater productivity
■ Actuated by foot switch
■ Key retains heads, or heads and feed
tracks
Specifications
Outside Diameter — 1.62 [41.2]
Length — 5.00 [127]
Height — 7.00 [178]
Weight — 2 lb [0.91 kg]
Air Pressure — 40 - 70 psi
[2.76 - 4.83 bar]
Air Lines (2) — 7 ft [2.13 m] long,
3/16 [4.76] I.D. with 1/8 [3.18]
NPT fitting
Cycle Time — 0.7 - 0.8 s
Application Rates (Typ.) —
600 terminations per hr;
1 100 terminations per hr with optional
Loose-Piece Feed Track; and
1 250 terminations per hr with optional
Tape (Reel) Feed Track (when produc-
ing 6 in [15 cm] jumpers, one
4-pos. MTA-100 connector each end,
discrete wire)
Bench Mount Power Units
Notes: 1. Interchangeable terminating heads must be ordered separately, see page 4.
2. Loose-piece or tape (reel) feed track accessories are available, see page 3.
Pistol Grip Power Units
Pistol Grip Hand Tool System
for Insulation Displacement Connectors (IDCs)
Catalog
296176
Revised 02-01