Datasheet

Pin and Socket
82068
Connectors
82181
65816
124799
82183
Printed Circuit
Board Connectors
82056
4
For drawings or technical data, contact your Tyco Electronics sales engineer or call the Technical Support Center: 1-800-522-6752.
Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents.
Specifications subject to change. Consult Tyco Electronics for latest specifications.
296176—5M—GATD—FP—02-01—015
Printed in U.S.A.
Tyco Electronics Corporation, Harrisburg, PA 17105; Phone: [phone]; Technical Support Center Fax: [phone]; Internet: www.amp.com/tooling
AMP
IDC Product
Terminating Head with Terminating Head
Manual Handle Assembly Only
Subminiature D HDE-20
Plugs and Receptacles
(AMPLIMITE)
Commercial MATE-N-LOK
4 Circuit Socket Assembly (Plug)
AMPMODU
MT
Interconnection MTE**
System
Level V
MT-6/MT-7
MT-6
Female
Connector
Connectors
Male
System
MT-7
Female
Connectors
Male
2 mm CT (Common Termination)
Connector System —
MT Receptacles
Closed-End
Receptacles**
MTA-100
Feed-Through
Receptacles
Posted
(Closed-End)
MTA
Closed-End
(Mass Termination
Receptacles**
Assemblies)
and
Quad Connectors**
Feed-Through
MTA-156
Receptacles
Card-Edge
(Closed-End)
Posted
(Closed-End)
AMP Communications Outlet
Card Edge Connector Kits
608868-1 58063-2 408-9414
— 231894-1 408-3186
58577-1 58062-1 408-9085
— 58336-1 408-9359
58582-1 58395-1 408-9472
— 58418-1 408-9557
— 58419-1 408-9574
— 58420-1 408-9575
— 58421-2 408-4115
— 58372-1 408-9426
58579-1 58246-1 408-6929
— 58246-2*** 408-9379
—
58246-3
408-4147
(for ribbon cable or discrete wire)
— 58442-1 408-9603
58645-1 58644-1
Pending
Mass-Insertion (2-12 pos.) Mass-Insertion (2-12 pos.)
58639-1 58638-1 408-4358
58580-1 58247-1 408-6930
— 58247-2*** 408-9380
—
58247-3
408-4146
(for ribbon cable or discrete wire)
— 58443-1 408-9607
58647-1 58646-1
Pending
Mass-Insertion (2-8 pos.) Mass-Insertion (2-8 pos.)
— 58061-1 408-6794
— 58082-1 408-6795
58633-1 58585-1 408-4191
58568-1 122533-1 408-4074
*See catalog for a complete listing of part numbers each terminating head will apply.
**Feed Track Accessories shown on page 3.
***Extended-wear terminating head.
Part Numbers
Product Catalog
Family Number*
Instruction
Sheet Number
CHAMP Category 5
Connectors
Product Facts
■ Most fit all pistol grip and bench
mount power units
■ Terminate unstripped wire
■ Align and hold connectors in place for
each termination
■ Most heads automatically advance
connectors after each termination
Specifications
Length — 3.18 to 3.62 [80.8 to 91.9]
Width — 1.00 to 2.62 [25.4 to 66.6]
Height — 1.12 to 2.62 [28.4 to 66.6]
Weight — 3 to 12 oz [85 to 340 g]
Note: Contact the Technical Support
Center at 1-800-522-6752 for more
information.
Miscellaneous
124344
Connectors
Networking/Premises
82164
Cabling Connectors
Bench Mount Power Units (Continued)
Pistol Grip Hand Tool System
for Insulation Displacement Connectors (IDCs)
Catalog
296176
Revised 02-01