Datasheet

ManualsBrandsTE CONNECTIVITY ManualsPCB ConnectorsSL-156 Content: 1 pc(s)

Locator Assembly

(Supplied with

Die Assembly)

Front of Tool

(Locator Side)

Die Assembly

Moving Jaw

Ratchet Adjustment Wheel

Moving Handle

Pivot Pin

PRO-CRIMPER III

Hand Crimping Tool

Frame 354940-1

(408-9930)

Back of Tool

(Wire Side)

Stationary

Handle

Stationary Jaw

TE DIE

ASSEMBLY

LOCATOR

ASSEMBLY †

CONTACT

FAMILY ‡

WIRE

SIZE

WG)

INSULATION

DIAMETER

STRIP LENGTH

(mm [In.]

58614-2 58515-1

SL156

Series

Connectors

24 - 20 L

1.52 - 2.79

[.060 - .110]

3.96 ± 0.38

[.156 ± .015]

1.09 - 1.91

[.043 - .075

24 - 20 S

† Supplied with die assembly. Also available separately.

‡Contact the TOOLING ASSISTANCE CENTER or PRODUCT INF

ORMATION (see below) for specific contact part numbers.

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.

1 of 6

Instruction Sheet

TOOLING ASSISTANCE CENTER

1-800-722-1111



PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com

LOC B

408-4228

PRO-CRIMPER* III Hand Crimping

Tool Assembly 58614-1 with

Die Assembly 58614-2

05 MAY 11 Rev C

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use

and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

Figure 1

1. INTRODUCTION

PRO-CRIMPER III Hand Crimping Tool Assembly

58614-1 consists of Die Assembly 58614-2 and PRO-

CRIMPER III Hand Crimping Tool Frame 354940-1.

The die assembly consists of crimping dies and a

locator assembly.

Read these instructions thoroughly before crimping

any cont

acts.

NOTE

Dimensions on this sheet are in millimeters [with

inch equivalents provided in brackets]. Figures and

illustrations are f

or identification only and are not

drawn to scale.

Reasons for revision are listed in Section 11,

REVISION SUMMAR

The PRO-CRIMPER III Hand Crimping Tool is a “Commercial" grade

tool and is designed primarily for field installation, repair, maintenance

work, or prototyping in industrial, commercial, or institutional

applications. Product crimped with this tool will meet the crimp height

requirement for hand tools in the appropriate Application Specification

(114-series), but may not comply with other feature parameters of the

specification. Tyco Electronics offers a variety of tools to satisfy your

performance requirements. For additional information, contact the

Tooling Assistance Center at 1-800-722-1111.

Summary of content (6 pages)

PAGE 1
Instruction Sheet PRO-CRIMPER* III Hand Crimping Tool Assembly 58614-1 with Die Assembly 58614-2 408-4228 05 MAY 11 Rev C PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.
PAGE 2
408-4228 2. DESCRIPTION (Figure 1 and Figure 2) The tool features a tool frame with a stationary jaw and handle, a moving jaw, a moving handle, and an adjustable ratchet that ensures full contact crimping. The tool frame holds a die assembly with three crimping sections. The die assembly features a wire anvil, an insulation anvil, a wire crimper, and an insulation crimper. Attached to the outside of the frame is a locator assembly, which contains a locator, a spring retainer, and a contact support.
PAGE 3
408-4228 6. Tighten the nut and close the handles until the ratchet releases. 11. To disassemble, close the tool handles until the ratchet releases, remove the nut, the locator assembly, the two die retaining screws, and the four die retaining pins, and slide the anvils and crimpers out of the tool jaws. 7. Remove and inspect the contact. 8. Make another sample crimp. If the contact is straight, tighten the contact support screw.
PAGE 4
08-4228 3. Position the contact so that the mating end of the contact is on the locator side of the tool, and so that the open "U" of the wire and insulation barrels must face the top of the tool. Place the contact up into the nest so that the movable locator drops into the slot in the contact. Refer to Figure 3. Butt the front end of the wire barrel against the movable locator. CAUTION Make sure that both sides of the insulation barrel are started evenly into the crimping section.
PAGE 5
408-4228 8. MAINTENANCE Ensure that the tool and dies are clean by wiping them with a clean, soft cloth. Remove any debris with a clean, soft brush. Do not use objects that could damage the tool. When not in use, keep handles closed to prevent objects from becoming lodged in the crimping dies, and store in a clean, dry area. 9. VISUAL INSPECTION The crimping dies should be inspected on a regular basis to ensure that they have not become worn or damaged.
PAGE 6
408-4228 Toling Compatible with Die Assembly 58614-2 PRO-CRIMPER III Hand Tool Frame 354940-1 (Instruction Sheet 408-9930) SDE-SA Hand Tool 9-1478240-0 (Instruction Sheet 408-8851) SDE Bench Terminator 1490076-2 (Customer Manual 409-10052) 626 Adapter 679304-1 (Instruction Sheet 408-4070) Electro-Hydraulic (BT 3500 Battery-Hydraulic) Hand Tool Kits 2031400-[ ] (Customer Manual 409-10095) Rev C Closed Head Assembly 2031460-1 (Instruction Sheet 408-10312) “C”-Head Assembly 2031450-1 (Instruction Sheet