LSA-PLUS® Series 2 Connection and Disconnection Modules and Accessories 1st Edition
LSA-PLUS® Series 2 Connection and Disconnection Modules and Accessories A technically and commercially superior quick connection system for all state-of-the-art networks. Contacts that ensure the highest degree of reliability even under the most adverse environmental and climatic conditions. A completely reliable, gas-tight connection between the contact and conductor. That's LSA-PLUS® technology.
LSA-PLUS® and LSA PROFIL® Connection Modules Series 2 Eight- and Ten-Pair Modules Features & Benefits • Based on genuine LSA-PLUS® connection technology • Available in eight- and ten-pair configurations with parallel test access or overvoltage protection contact • LSA-PLUS modules mount on back mount frames • LSA PROFIL modules mount on profile rods (8-pair modules: 75mm spacing between rods; 10-pair modules: 95mm spacing between rods) or on back mount frames • Suitable for use in all xDSL and ADSL2+ circui
LSA-PLUS® and LSA PROFIL® Disconnection Modules Series 2 Eight- and Ten-Pair Modules Features & Benefits • Eight- and ten-pair modules with disconnection points for opening the line, testing in both directions or insertion of graded protection elements • Based on genuine LSA-PLUS® connection technology • LSA-PLUS modules mount on back mount frames • LSA PROFIL modules mount on profile rods (8-pair modules: 75 or 95mm spacing between rods; 10-pair modules: 95mm spacing between rods) or on back mount frames •
LSA PROFIL® Series 2 Disconnection Module for 2 Mbps Networks Description The expansion of mobile communications networks, the introduction of new mobile phone systems (3G, UMTS, 4G, LTE) and the steady growth of IP networks, have created a demand for bandwidth in both access and transmission networks. This in turn causes the extension of existing hubs and the installation of new hubs. The ADC KRONE PROFIL system provides a foundation for networks served by 2 Mbps copper pairs with impedance of 120 Ohms.
LSA-PLUS® and LSA PROFIL® Modules Mounting and Labelling Accessories Back mount frames Selection criteria Calculating necessary installation space: Back mount frame length = Module spacing x (number of modules – 1) + 20mm Frame depth: based on conductor diameter of 0.5mm, including insulation of 1.5mm. Deeper frames must be selected for wires measuring 0.6mm – 0.9mm, or when the cable is fed through the frame bundle by bundle.
LSA-PLUS® and LSA PROFIL® Modules Back Mount Frames with 22.5mm and 25.0mm Module Spacing Ordering Information Description LSA-PLUS Series 2, 10-pair, Depth of cable space/frame: 22.5mm Hole pattern: 1 LSA-PLUS Series 2, 10-pair, Depth of cable space/frame: 25mm Hole pattern: 2 LSA-PLUS Series 2, 8-pair, Depth of cable space/frame: 22.
LSA-PLUS® and LSA PROFIL® Modules Back Mount Frame with 27.5mm Module Spacing Ordering Information Description LSA-PLUS Series 2, 10-pair, Depth of cable space/frame: 22mm Hole pattern: 2 LSA-PLUS Series 2, 10-pair, Depth of cable space/frame: 50mm Hole pattern: 2 8 Number of Modules Depth of Cable Space Module spacing Catalog Number 4 22mm 27.5mm 6569 3 054-11 6 22mm 27.5mm 6569 3 054-12 11 22mm 27.5mm 6569 3 054-13 13 22mm 27.
LSA-PLUS® and LSA PROFIL® Modules Back Mount Frame Features & Benefits • Accommodates from 10 to 40 Series 2, 10-pair modules, plus an additional termination module, label holder or earth-wire module • Blocks of 100 pairs separated from each other (spacing between groups of 10 modules is 30mm) • Overall width: 104.5mm • Module spacing: 22.
LSA-PLUS® and LSA PROFIL® Modules Modular Back Mount Frame Features & Benefits • Total of 45 module mounting slots in two sections (one with 22 slots, one with 23) • Five pre-stressed break-off points between the module's slits can be cut with a saw, allowing the frame to be cut on-site to the desired length • Back of the frame contains both hole patterns 1 and 2 • Use of the maximum (45) mounting slots is recommended when a total of 100 pairs are to be terminated on a frame with a cable space depth of 22mm
LSA-PLUS® and LSA PROFIL® Modules Back Mount Frame for Cable Head Installations Features & Benefits • For installations with limited or narrow space • Two sizes, accommodating five or ten LSA-PLUS® Series 2, 10-pair modules plus an additional termination module, label holder or earth-wire module • No mounting materials (screws, nuts, washers) are included Ordering Information Description Catalog Number Back mount frame for Series 2, 10-pair modules, plus 1 additional module or label holder 11 Size 1, t
LSA-PLUS® and LSA PROFIL® Modules Dust Cover Features & Benefits • Transparent cover protects LSA-PLUS® Series 2, 10-pair modules from dust and accidental disturbance of terminated cable • The deeper version allows installation of overvoltage protection magazine Ordering Information Description Catalog Number Shallow dust cover 100 pairs 6092 3 016-00 50 pairs 6092 3 016-01 10 pairs Note: if more than 1 cover is used, module spacing must be greater than 22.5mm 6089 2 097-00 Deep dust cover.
LSA-PLUS® and LSA PROFIL® Modules Mounting accessories for Back Mount Frames Ordering Information Description Catalog Number Cable clamp kit for Series 2 cable head back mount frame Includes 4 clamps, 1 sheath contact screws, 1 clip 6092 2 017-00 Edge protection strip. Placed over unused positions in back mount frame 13 120mm 6092 3 017-00 60mm 6092 3 017-01 Cable protection rings for 15mm diameter cables. Mount on rear of back mount frame to protect cable insulation 6050 3 044-00 www.te.
LSA-PLUS® and LSA PROFIL® Modules Profile Rod Frames Features & Benefits • Profile frame consists of 2 stainless steel profile rods, each 12mm in diameter and profile holders 46mm in depth • Profile rod frame with 95mm distance between rods accommodates: – Series 2, 10-pair LSA PROFIL modules – Series 2, 8-pair LSA PROFIL modules – NT, 10-pair LSA PROFIL modules – HighBand® modules – HD 180 modules • Profile rod frame with 75mm distance between rods accommodates: – Series 2, 8-pair LSA PROFIL modules – NT,
LSA-PLUS® and LSA PROFIL® Modules Individual Profile Rods and Rod Holders Features & Benefits • Individual rods and rod holders may be ordered to construct a custom, modular frame • Rod holders with a depth of 86mm are available: deeper profile frames are used when cable support elements and cable guides are used • All profile holders accept 12mm diameter profile rods • One profile holder should be placed for each 500mm of profile rod Ordering Information Description Length of rods (mm) Catalog Number P
Mounting Accessories Mounting Adapter Features & Benefits • Used for installation of small to medium indoor distributors • Permits wall mounting of back mount frames or profile rods (95mm distance between poles) • Snap-on feature allows additional adapters to be installed either vertically or horizontally Ordering Information Description LSA-PLUS, LSA PROFIL mounting adapter Features 3 locations for cable attachment, 2 jumper guides, 2 mounting holes. Mounting hardware must be ordered separately 16 www.
Mounting Accessories Profile Rod Installation Accessories 17 www.te.
Mounting Accessories Profile Rod Installation Accessories Ordering Information Description Dimensions (H x W x D) Catalog Number Bar bracket For profile rods distance: 95mm Suitable for use with profile rods with M5 threaded rod Quantity: 2 50mm x 154mm x 44mm 6619 2 025-00 Jumper hooks Snap onto bar bracket Distance between hooks: 120mm Quantity: 4 Depth: 93mm 6619 2 031-00 Jumper guide Snaps onto profile rod Recommended spacing between frames: >60mm Quantity: 2 10mm x 45mm 6619 2 016-00 Profil
Mounting Accessories DIN Rail Adapter Ordering Information Description Catalog Number DIN Rail adapter used to secure 35mm high LSA PROFIL modules onto DIN rails (DIN 50022) Quantity: 10 6461 2 013-00 Protective Cover Strip for Series 2 10-pair Modules Protective cover For Series 2 modules Protects cable leads or jumper wires; designed to break when attempt is made to remove it 19 Gray 6089 3 050-00 Red 6089 3 050-10 www.te.
Labelling Accessories Label Holder Module Ordering Information Description Dimensions (H x W x D) Catalog Number 75mm x 13.2mm 6036 2 018-00 Blank 95mm x 25mm 6092 2 012-01 Printed 95mm x 17.9mm 6092 2 012-00 Blank 95mm x 17.9mm 6092 2 012-02 Blank, with earth socket 63mm x 17.
Labelling Accessories Hinged Label Holder Ordering Information Description Dimensions (H x W x D) Catalog Number 8-pair modules 83.3mm x 11.5mm 6036 2 005-02 10-pair modules 102.5mm x 11.5mm 6089 2 015-01 Hinged label holder Snaps onto LSA-PLUS and LSA PROFIL Series 2, 8- or 10-pair modules, as well as overvoltage magazines. Transparent cover and paper label. Blank Quantity: 1 21 www.te.
Labelling Accessories Number Flags for Series 2 Modules Ordering Information Color 22 Numbering Quantity Catalog Number Gray 1……50 1 piece each number 6089 2 077-00 Gray 51……120 1 piece each number 6089 2 077-03 Gray 1….0 10 pieces 6089 3 023-00 Gray 10…100 10 pieces 6089 3 023-01 Red 1….
Insertion Tools LSA-PLUS® Insertion Tools Insertion Tool with Sensor • U sed with all LSA-PLUS® modules, as well as with RJ5 jacks and HighBand® modules • For termination of wires with conductor diameter range 0.35 to 0.9mm; overall diameter range 0.7 to 2.6mm • Features a sensor that detects the end of a wire when a termination has been completed.
LSA-PLUS® and LSA PROFIL® Series 2 Modules Accessories: Plugs and Cords Ordering Information Description Catalog Number Marking cap 1-pair. Used for identification of connections Minimum order quantity: 100 6089 3 006-XX* Dummy plug 1-pair. With marking area for identification of lines. Used to prevent access to connection modules or disconnection of disconnection modules Minimum order quantity: 100 6417 3 105-XX* 3-pole, with extraction ring.
LSA-PLUS® and LSA PROFIL® Series 2 Modules Accessories: Plugs and Cords Test Cord The two-pole test cord features a 4mm double socket and can be used for almost all LSA-PLUS systems, including NT modules, Series 2, Series 8 or Series 10 modules, as well as two- to eight-pole PCB modules. The cord is used whenever the module’s existing test access is already occupied by another plug (such as changeover adapters and/or disconnection adapters) or when a module has no special test access.
LSA-PLUS® and LSA PROFIL® Series 2 Modules Accessories: Plugs and Cords Test Cords 26 www.te.
LSA-PLUS® and LSA PROFIL® Series 2 Modules Accessories: Plugs and Cords Ordering Information Description Catalog Number 2-pole test cords For use with LSA-PLUS and LSA-PROFIL modules 1 LSA-PLUS plug, (2) 4mm banana plugs 2.0 m 6624 2 061-02 6.0 m 6624 2 061-06 1 LSA-PLUS plug, (2) 4mm banana sockets 0.20 m 6624 2 040-09 2.0 m 6624 2 040-02 2-pole test cords 1 side access with disconnection function For use with LSA-PLUS or LSA PROFIL disconnection modules 1 LSA-PLUS plug, (2) 4mm banana plugs 2.
LSA-PLUS® and LSA PROFIL® Series 2 Modules Accessories: Plugs and Cords Connection Cords 28 www.te.
LSA-PLUS® and LSA PROFIL® Connection Modules Series 2 Eight- and Ten-Pair Modules Ordering Information Description Catalog Number 2-pole connection cord For parallel connections. Features (2) 2-pole plugs 2.0 m 6624 2 081-02 6.0 m 6624 2 081-06 4-pole connection cord with disconnection function For use with LSA-PLUS and LSA PROFIL disconnection modules. Features (2) 4-pole plugs, with a/a and b/ cross-connected 2.0 m 6624 2 821-02 6.
LSA-PLUS® and LSA PROFIL® Connection Modules Series 2 Eight- and Ten-Pair Modules Ordering Information Description Catalog Number 10-pair, 40-pole plug with PCB insert For use with 10-pair LSA-PLUS and LSA PROFIL disconnection or switching modules.
TE Connectivity and TE connectivity (logo) are trademarks. Other logos, product and/or Company names might be trademarks of their respective owners While Tyco Electronics has made every reasonable effort to ensure the accuracy of the information in this document, Tyco Electronics does not guarantee that it is error-free, nor does Tyco Electronics make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current.
