Information

ManualsBrandsTE CONNECTIVITY ManualsPCB ConnectorsSocket enclosure - cable AMPSEAL16 Total number of pins 12 1 pc(s)

Product

Specification

108-2184

11Mar11 Rev B

AMPSEAL 16* Connector System

1. SCOPE

1.1. Content

This specification covers perform ance, tests and quality requirements for the AMPSEAL 16* Connector

System .

1.2. Qualification

W hen tests are perform ed on the subject product line, procedures specified in Figure 2 shall be used.

All inspections shall be perform ed using the applicable inspection plan and product drawing.

1.3. Successful qualification testing on the subject product line was com pleted on 25Nov03. The

Qualification Test Report num ber for this testing is 501-708. This docum entation is on file at and

available from Engineering Practices and Standards (EPS).

2. APPLICABLE DOCUM ENTS

The following documents form a part of this specification to the extent specified herein. Unless

otherwise specified, the latest edition of the docum ent applies. In the event of conflict between the

requirem ents of this specification and the product drawing, the product drawing shall take precedence.

In the event of conflict between the requirements of this specification and the referenced docum ents,

this specification shall take precedence.

2.1. TE Connectivity (TE) Docum ent

501-708: Qualification Test Report (AMPSEAL 16* Connector System )

2.2. Industry Standards

! ASTM B117: Standard Practice for Operating Salt Spray (Fog) Apparatus

! EIA-364: Electrical Connector/Socket Test Procedures Including Environm ental Classifications

! IEC 60512: Electrom echanical Components For Electronic Equipment; Basic Testing Procedures

and Measuring Methods Part 1: General

! SAE J1455: Recom mended Environm ental Practices for Electronic Equipm ent Design in

Heavy-Duty Vehicle Applications

! SAE J2030: Heavy-Duty Electrical Connector Perform ance Standard

2.3. Reference Docum ents

! 109-197: Test Specification (TE Test Specifications vs EIA and IEC Test Methods)

! 114-13045: Application Specification (HDSF Size 16 Pin and Socket Contacts)

! 114-13065: Application Specification (AMPSEAL 16 Connector System )

a TE Connectivity Ltd. Company

| Indicates change

*Trademark

For latest revision, visit our website at www.te.com/documents.

For Regional Customer Service, visit our website at www.te.com

1 of 6

TE logo is a trademark. Other products, logos, and company names might be trademarks of their respective owners. LOC B

Summary of content (6 pages)

PAGE 1
Product Specification 108-2184 11Mar11 Rev B AMPSEAL 16* Connector System 1. SCOPE 1.1. Content This specification covers perform ance, tests and quality requirem ents for the AMPSEAL 16* Connector System . 1.2. Qualification W hen tests are perform ed on the subject product line, procedures specified in Figure 2 shall be used. All inspections shall be perform ed using the applicable inspection plan and product drawing. 1.3.
PAGE 2
108-2184 3. REQUIREM ENTS 3.1. Design and Construction Product shall be of the design, construction and physical dim ensions specified on the applicable product drawing. 3.2. Materials Materials used in the construction of this product shall be as specified on the applicable product drawing. 3.3. Ratings ! ! Voltage: 250 volts DC Current: See Figure 1 (all readings in am peres) W ire Size (AW G) Connector Loading 14 18 20 Single Circuit Energized 16.0 10.0 7.
PAGE 3
108-2184 Test Description Requirem ent Procedure ELECTRICAL Low signal term ination resistance. Voltage drop. Insulation resistance. 6 m illiohm s m axim um for 14 and 16 AW G wire. 9 m illiohm s m axim um for 18 AW G wire. SAE J2030 6.2. Measure connection resistance across m ated term inals and subtract bulk resistance of Equal W ire Lengths (EW L). W ire Test Voltage Drop Size Current (m illivolts (AW G) (am peres) m axim um ) 14 13 100 16 10 100 18 8 100 SAE J2030 6.4.
PAGE 4
108-2184 Test Description Requirem ent Procedure Therm al shock. See Note. SAE J2030 6.13. Subject specim ens to 10 cycles between -40 and 120°C .with 1 hour dwells at tem perature extrem es. Sealing pressure. 35 kPa, pre-test, no bubbles. 35 kPa, post-test, no bubbles. EIA-364-2. Subject specim ens to specified pressure for 30 m inutes. Pressure washing. See Note. SAE J2030 6.5. and SAE J1455 4.5.
PAGE 5
108-2184 3.6.
PAGE 6
108-2184 4. QUALITY ASSURANCE PROVISIONS 4.1. Qualification Testing A. Specim en Selection Specim ens shall be prepared in accordance with applicable Instruction Sheets and shall be selected at random from current production. Specim ens shall consist of 2, 3 and 8 position connectors with TE HDSF size 16 gold plated pin and socket contacts and 14, 16 and 18 AW G GXL wire. B. Test Sequence Qualification inspection shall be verified by testing specim ens as specified in Figure 3. 4.2.