Datasheet
Mini- Universal MATE- N- LOK Splash- Proof Sealed Connect ors 114- 13089
Rev B8 of 20 Tyco Electronics Corporation
WIRE STRIP FORM CONTACT (Using Automatic Machine)
S
I
Z
E
(
A
W
G
)
INSULATION
WIRE BARREL CRIMP
INSULATION BARREL
S
I
Z
E
(
A
W
G
)
I
N
S
U
L
A
T
I
O
N
DIAMETER
HEIGHT WIDTH
I
N
S
U
L
A
T
I
O
N
B
A
R
R
E
L
WIDTH (Ref)
0.63+0.05 [.025+.002]
26
1.02--1.52
[
.040--.060
]
0.63+0.03/--0.05
[.025+.001/--.002]G
1.22
[
.048
]
2.03
[
.080
]
24
1
.
0
2
1
.
5
2
[
.
0
4
0
.
0
6
0
]
0.69+0.05 [.027+.002]
1
.
2
2
[
.
0
4
8
]
2
.
0
3
[
.
0
8
0
]
22 0.78+0.05 [.031+.002]
22 0.81+0.05 [.032+.002]
20
1.27--2.1 1 [.050--.083]
0.91+0.05 [.036+.002]
1.57 [.062]
2.79 [.1 10]z
18
1
.
2
7
2
.
1
1
[
.
0
5
0
.
0
8
3
]
1.07+0.05 [.042+.002]
1
.
5
7
[
.
0
6
2
]
2
.
7
9
[
.
1
1
0
]
z
GFor 7--strand, tin--coated wire with insulation diameter of 0.15 mm [.006 in.]. z2.54 mm [.100 in.] max when using wire seal.
WIRE LOOSE -- PIECE CONTACT (Using Hand Tool)
S
I
Z
E
(
A
W
G
)
INSULATION
WIRE BARREL CRIMP
INSULATION BARREL
S
I
Z
E
(
A
W
G
)
I
N
S
U
L
A
T
I
O
N
DIAMETER
HEIGHT WIDTH
I
N
S
U
L
A
T
I
O
N
B
A
R
R
E
L
WIDTH (Ref)
26 0.69+0.05 [.027+.002]
24
1.02--1.52 [.040--.060]
0.69+0.05 [.027+.002]
1.07 [.042] 2.03 [.080]
22
0
5
[
0
0
0
6
0
]
0.78+0.05 [.031+.002]
0
[
0
]
0
3
[
0
8
0
]
22 0.79+0.05 [.031+.002]
20
1.27--2.1 1 [.050--.083]
0.79+0.05 [.031+.002]
1.57 [.062]
2.79 [.1 10]z
18
[
0
5
0
0
8
3
]
1.04+0.05 [.041+.002]
5
[
0
6
]
2
.
7
9
[
.
1
1
0
]
z
z2.54 mm [.100 in.] max when using wire seal.
Figure 5 (end)
The developed crimp configurations result from using the specific tooling described in Section 5, TOOLING.
K. Twist and Roll
There should be no twist or roll of the crimped portions or mating portion of the contact that would cause
overstress or impair usage. Twist and roll is allowed within the limits specified in Figure 6.
Figure 6
Crimped
Portion
Allowable Twist and Roll
Datum Line
10_ Max
10_ Max
L. Bend Allowance
The force applied during crimping may cause some bending between the crimped portion and wire. Such
deformation is acceptable within the following limits.
1. Up and Down
The crimped portion, including the cutoff tab, must not be bent beyond the limits shown in Figure 7.
2. Side--to--Side
The crimped portion must not be bent from one side to the other beyond the limits shown in Figure 7.
NOTE
i