Datasheet

ManualsBrandsTE Connectivity ManualsConnectorsCrimp socket 3 A Female 24...20 AWG

181

Catalog 1307819 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000

Revised 8-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628

specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013

www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208

Mod IV Receptacle Assemblies, Single-Row, Outrigger Design

.100 x .100 [2.54 x 2.54] Centerline, End To End Stackable

AMPMODU Interconnection System

Vertical Mount,

Receptacle Assemblies

No. of

Dimensions Contact Plating/Part Nos.

Pos.

A B Plating A Plating B Plating C

3 .300 [7.62] .200 [5.08] 5-147720-2 5-147726-2 5-147727-2

4 .400 [10.16] .300 [7.62] 5-147720-3 5-147726-3 5-147727-3

5 .500 [12.70] .400 [10.16] 5-147720-4 5-147726-4 5-147727-4

6 .600 [15.24] .500 [12.70] 5-147720-5 5-147726-5 5-147727-5

7 .700 [17.78] .600 [15.24] 5-147720-6 5-147726-6 5-147727-6

8 .800 [20.32] .700 [17.78] 5-147720-7 5-147726-7 5-147727-7

9 .900 [22.86] .800 [20.32] 5-147720-8 5-147726-8 5-147727-8

10 1.000 [25.40] .900 [22.86] 5-147720-9 5-147726-9 5-147727-9

11 1.100 [27.94] 1.000 [25.40] 6-147720-0 6-147726-0 6-147727-0

12 1.200 [30.48] 1.100 [27.94] 6-147720-1 6-147726-1 6-147727-1

13 1.300 [33.02] 1.200 [30.48] 6-147720-2 6-147726-2 6-147727-2

14 1.400 [35.56] 1.300 [33.02] 6-147720-3 6-147726-3 6-147727-3

15 1.500 [38.10] 1.400 [35.56] 6-147720-4 6-147726-4 6-147727-4

16 1.600 [40.64] 1.500 [38.10] 6-147720-5 6-147726-5 6-147727-5

17 1.700 [43.18] 1.600 [40.64] 6-147720-6 6-147726-6 6-147727-6

18 1.800 [45.72] 1.700 [43.18] 6-147720-7 6-147726-7 6-147727-7

19 1.900 [48.26] 1.800 [45.72] 6-147720-8 6-147726-8 6-147727-8

20 2.000 [50.80] 1.900 [48.26] 7-147720-8 7-147726-8 7-147727-8

30 3.000 [76.20] 2.900 [73.66] 8-147720-8 8-147726-8 8-147727-8

40 4.000 [101.60] 3.900 [99.06] 8-147720-9 8-147726-9 8-147727-9

Notes: 1. Tyco Electronics recommends mating gold or duplex plated headers with duplex plated receptacle

assemblies.

2. To obtain the minimum mating post length, add .020 [0.51] (not including the post lead in chamfer) to

the maximum point-of-contact dimension and add .062 [1.57] for recommended board thickness if used in

bottom entry application.

Material and Finish

Housing — Glass-filled thermoplastic,

black, 94V-0 rated

Plating A — Duplex .000030 [0.00076]

gold on contact area, .000150-0.000300

[0.00381-0.00762] matte tin on solder

area all over .000050 [0.00127] nickel

Plating B — Duplex .000010

[0.000254] gold on contact area,

.000150-.000300 [0.00381-0.00762]

matte tin on solder area all over .000050

[0.00127] nickel

Plating C — .000150-.000300

[0.00381-0.00762] matte tin on solder

leads, all over .000050 [0.00127] nickel

.245

[6.22]

.140

[3.56]

.075

+.005

-.000

[

1.90

+0.13

]

-.000

.140

[3.56]

.125±.010

[3.17±0.25]

Ty p.

Recommended PC Board Hole Layout

.020

[0.51]

(Standoffs)

.100

[2.54]

Ty p.

.053

[1.34]

Ty p.

.200

[5.08]

.035±.003

[0.89±0.08]

Dia.

.200±.003

[5.08±0.08]

Ty p.

.100

[2.54]

Ty p.

Dual Entry, End Stackable,

Low Profile, .100 x .100

[2.54 x 2.54] Centerline,

.200 [5.08] Tine Spacing

.107

[2.72]

(Localized Gold

Plate Area)

.148

[3.77]

Ty p.

Point of

Contact

Note: All part numbers are RoHS

compliant.

Summary of content (98 pages)

PAGE 1
AMPMODU Interconnection System Mod IV Receptacle Assemblies, Single-Row, Outrigger Design .100 x .100 [2.54 x 2.54] Centerline, End To End Stackable Dual Entry, End Stackable, Low Profile, .100 x .100 [2.54 x 2.54] Centerline, .200 [5.08] Tine Spacing .125±.010 [3.17±0.25] Typ. .020 [0.51] (Standoffs) .245 [6.22] .148 [3.77] Typ. A Point of Contact .107 [2.72] (Localized Gold Plate Area) .200±.003 [5.08±0.08] Typ. Material and Finish .140 [3.56] .053 [1.34] Typ. .100 [2.54] Typ. B .075 +.005 -.
PAGE 2
AMPMODU Interconnection System Mod IV Receptacle Assemblies, Double-Row, Outrigger Design, .100 x .100 [2.54 x 2.54] Centerline, End to End Stackable Dual Entry, End Stackable, Low Profile, .100 x .100 [2.54 x 2.54] Centerline, .300 [7.62] Tine Spacing .020 [0.51] (Standoffs) .245 [6.22] Typ. A .148 [3.77] Typ. .050 [1.27] Max. Typ. Vertical Mount, Receptacle Assemblies Housing — Glass-filled thermoplastic, black, 94V-0 rated Contacts — Phosphor bronze, plated as follows: Plating A — Duplex .
PAGE 3
AMPMODU Interconnection System Mod. IV Receptacle Assemblies, Double-Row, .100 x .100 [2.54 x 2.54] Centerline .020 [0.51] Typ. (Standoffs) Closed Dual Entry, Side and End Stackable Low Profile, .100 x .100 [2.54 x 2.54] Centerline, .150 [3.81] Tine Spacing .245 [6.22] Typ. A .050 [1.27] Max. Typ. Material and Finish .100±.003 [2.54±0.08] Technical Documents — page 276 Product Specification 108-25022 Application Specification 114-25018 Note: All part numbers are RoHS compliant. .150 [3.81] Typ. .
PAGE 4
AMPMODU Interconnection System Mod. IV Receptacle Assemblies, Double-Row, .100 x .100 [2.54 x 2.54] Centerline (Continued) No. of Pos. Plating A 7-535542-1 7-535542-2 7-535542-3 7-535542-4 7-535542-5 7-535542-6 7-535542-7 7-535542-8 7-535542-9 8-535542-0 8-535542-1 8-535542-2 8-535542-3 8-535542-4 8-535542-5 8-535542-6 8-535542-7 8-535542-8 8-535542-9 9-535542-0 Contact Plating/Part Nos.
PAGE 5
AMPMODU Interconnection System Mod IV Surface Mount Vertical Receptacle Assemblies, .100 x .100 [2.54 x 2.
PAGE 6
AMPMODU Interconnection System Mod IV Surface Mount Vertical Receptacle Assemblies, .100 x .100 [2.54 x 2.54] Centerline (Continued) Voltage Rating: 250 VAC Current Rating: 3.0 amperes (max.) for single contact; 2.0 amperes (max.) per contact when connector is fully energized Operating Temperature Range (Receptacle Assemblies): –65°C to +125°C Operating Temperature Range (Headers): -65°C to +105°C Dielectric Withstanding Voltage: 750 VAC Termination Resistance: 12 milliohms (max.
PAGE 7
AMPMODU Interconnection System Mod IV Receptacle Assemblies, Single-Row, Surface Mount, .100 [2.54] Centerline with Compliant Pin Hold Downs Surface Mount, Single-Row, Dual Entry with Compliant Pin Holddowns [ ] .030 0.76 .025 0.64 Typ. .038 [0.97] .020 Standoffs [0.51] Typ. .265 [6.73] Typ. .107 [2.72] D C Material and Finish .100 [2.54] Typ. D B .500 [12.70] .600 [15.24] .700 [17.78] .800 [20.32] .900 [22.86] 1.000 [25.40] 1.100 [27.94] 1.200 [30.48] 1.300 [33.02] 1.400 [35.56] 1.500 [38.10] 1.
PAGE 8
AMPMODU Interconnection System Mod IV Receptacle Assemblies, Single-Row, Surface Mount, .100 [2.54] x .100 [2.54] Centerline End To End Stackable without Compliant Pin Holddowns .020 [0.51] Standoff Typ. Surface Mount,Single-Row, Dual Entry, End to End Stackable .265 [6.73] Housing — Glass-filled thermoplastic, black, 94V-0 rated Contacts — Phosphor bronze, plated as follows: Plating A — Duplex .000030 [0.00076] gold on contact area, .000150-.000300 [0.00381-0.00762] matte tin on solder area all over .
PAGE 9
AMPMODU Interconnection System Mod IV Surface Mount Receptacle Assemblies, Double-Row, .100 x .100 [2.54 x 2.54] Centers Surface Mount,Double Row, Dual Entry with Holddowns A .100 [2.54] Typ. .050 [1.27] Typ. .198 [5.03] Material and Finish .083 [2.12] Typ. .020 [0.51] Typ. .027±.002 [0.69±0.05] Typ. .110 [2.79] Typ. B .040±.003 [1.02±0.08] .100 [2.54] Typ. .266 [6.75] .238 [6.05] Typ.
PAGE 10
AMPMODU Interconnection System Mod IV Surface Mount Receptacle Assemblies, Double-Row, .100 x .100 [2.54 x 2.54] Centers (Continued) No. of A Pos. 10 .700 [17.78] 14 .900 [22.86] 20 1.200 [30.48] 22 1.300 [33.02] 26 1.500 [38.10] 30 1.700 [43.18] 34 1.900 [48.26] 36 2.000 [50.08] 40 2.200 [55.88] 46 2.500 [63.50] 50 2.700 [68.58] 62 3.300 [83.82] 64 3.400 [86.36] 66 3.500 [88.90] 70 3.700 [95.98] 80 4.300 [109.22] Dimensions B .400 [10.16] .600 [15.24] .900 [22.86] 1.000 [25.40] 1.200 [30.48] 1.400 [35.
PAGE 11
AMPMODU Interconnection System Mod IV Surface Mount Receptacle Assemblies, Double-Row, .100 x .100 [2.54 x 2.54] Centerline Surface Mount,Double Row, Dual Entry End to End Stackable A .100 [2.54] Typ. .100 [2.54] Typ. .198±.002 [5.03±0.05] .050 [1.27] Max. .148 Point of [3.76] Contact .265 [6.73] Typ. Material and Finish .020 [0.51] Typ. .027±.002 Typ. [0.69±0.05] .266 [6.
PAGE 12
AMPMODU Interconnection System Mod IV Surface Mount Receptacle Assemblies, Double-Row, .100 x .100 [2.54 x 2.54] Centerline (Continued) No. of Pos. Dimensions A 10 14 20 22 26 30 34 36 40 46 50 62 64 66 70 80 .500 [12.70] .700 [17.78] 1.000 [25.40] 1.100 [27.94] 1.300 [33.02] 1.500 [38.10] 1.700 [43.18] 1.800 [45.72] 2.000 [50.80] 2.300 [58.42] 2.500 [63.50] 3.100 [78.74] 3.200 [81.28] 3.300 [83.82] 3.500 [88.90] 4.000 [101.60] B .400 [10.16] .600 [15.24] .900 [22.86] 1.000 [25.40] 1.200 [30.48] 1.
PAGE 13
AMPMODU Interconnection System Two-Piece Printed Circuit Board Connectors Product Facts Two-Piece reliability ■ Two- and three-row systems available ■ Short signal path for VLSI applications ■ Receptacles employ dual cantilever beams and builtin anti-overstress to provide reliable connections ■ Built-in guides provide alignment before contact engagement ■ Closed entry receptacle housings provide lead-in ramp for positive mating of contacts ■ Shrouded headers provide full pin protection ■ Pola
PAGE 14
AMPMODU Interconnection System Two-Piece Printed Circuit Board Connectors (Continued) AMPMODU Two-Piece Printed Circuit Board connectors are designed to reliably and economically meet the packaging and interconnection requirements of today’s sophisticated electronics. The double row system is produced in 10 thru 200 positions in the vertical headers and horizontal receptacles, and 10 thru 160 positions in the right angle headers and vertical receptacles.
PAGE 15
AMPMODU Interconnection System Receptacle Assemblies, Board Mount, Double-Row, Closed Entry, .100 x .100 [2.54 x 2.54] Centerline Horizontal Mount (with Guide Pin Slots and Standoffs) .320 [8.13] .174 Max. [4.42] (Point of Contact) A Material and Finish .179 [4.55] Typ. B Housing — Glass-filled thermoplastic, black, 94V-0 rated Contacts — Phosphor bronze, plated as follows: Plating A — Duplex plated .000030 [0.00076] gold on contact area, .000050.000100 [0.00127-0.
PAGE 16
AMPMODU Interconnection System Receptacle Assemblies, Board Mount, Double-Row, Closed Entry, .100 x .100 [2.54 x 2.54] Centerline (Continued) Vertical Mount (with Guide Pin Slots and Standoffs) .115 [2.92] .129 Typ. [3.28] .410 [10.41] .320 [8.13] Material and Finish .100 Typ. [2.54] Housing — Glass-filled thermoplastic, black, 94V-0 rated Contacts — Phosphor bronze, duplex plated .000030 [0.00076] gold on contact area, .000050-.000100 [0.00127-0.
PAGE 17
AMPMODU Interconnection System Receptacle Assemblies, Board Mount, Triple-Row, Closed Entry, .100 x .100 [2.54 x 2.54] Centerline Horizontal Mount (with Guide Pin Slots and Standoffs) A .410 [10.41] .179 Typ. [4.55] Material and Finish Housing — Glass-filled thermoplastic, black, 94V-0 rated Contacts — Phosphor bronze, plated .000030 [0.00076] gold in mating area, .000050-.000100 [0.00127-0.00254] matte tin on solder area, with entire contact underplated .000050 [0.00127] nickel .100 Typ. [2.54] .
PAGE 18
AMPMODU Interconnection System Headers, Straight Post, Double-Row, .100 x .100 [2.54 x 2.54] Centerline Solder Posts and ACTION PIN Posts (with Pin Protection and Guide Pins) Pos. Ref. .065 R [1.66] (2 Plc.) 1 2 3 .100 [2.54] .515 [13.08] .085 [2.16] .200 [5.08] .130 [3.30] (2 Plc.) B .040 [1.02] (4 Sides) A Material and Finish Printed Circuit Board Connectors Housing — Glass-filled thermoplastic, black, 94V-0 rated Posts — Phosphor bronze, plated as follows: Plating A — Duplex plated .
PAGE 19
AMPMODU Interconnection System Headers, Straight Post, Double-Row, .100 x .100 [2.54 x 2.54] Centerline (Continued) See chart below .025 [0.64] Square ACTION PIN Tails Dimensions A 12 14 20 24 36 40 50 60 70 80 90 96 100 120 130 .980 [24.89] 1.080 [27.43] 1.380 [35.05] 1.580 [40.13] 2.180 [55.37] 2.380 [60.45] 2.880 [73.15] 3.380 [85.85] 3.880 [98.55] 4.380 [111.25] 4.880 [123.95] 5.180[131.57] 5.380 [136.65] 6.380 [162.05] 6.880 [174.75] B .500 [12.70] .600 [15.24] .900 [22.86] 1.100 [27.94] 1.
PAGE 20
AMPMODU Interconnection System Headers, Right-Angle Post, Double-Row, .100 x .100 [2.54 x 2.54] Centerline Card Extender (with Pin Protection and Guide Pins) .762 Max. [19.35] .599 [15.21] .040 [1.02] Typ. .100 [2.54] Material and Finish Printed Circuit Board Connectors Housing — Glass-filled thermoplastic, black, 94V-0 rated Posts — Phosphor bronze, plated as follows: Plating A — Duplex plated .000030 [0.00076] gold on contact area, .000100-.000200 [0.00254-0.
PAGE 21
AMPMODU Interconnection System Headers, Straight Post, Triple-Row, .100 x .100 [2.54 x 2.54] Centerline Solder Posts (with Pin Protection and Guide Pins) Pos. Ref. 1 2 .065 R [1.65] (2 Plc.) 3 .100 [2.54] .615 [15.62] .100 [2.54] .200 [5.08] .085 [2.16] .040 [1.02] (4 Sides) Material and Finish Housing — Glass-filled thermoplastic, black, 94V-0 rated Posts — Phosphor bronze, plated as follows: Plating A — Duplex plated .000030 [0.00076] gold on contact area, .000100-.000200 [0.00254-0.
PAGE 22
AMPMODU Interconnection System Headers, VRM (Voltage Regulator Module), .100 x .100 [2.54 x 2.54] Centerline Solder Posts and ACTION PIN Posts (with Pin Protection, Guide Ribs, and Latching) A B .515 [13.08] Material and Finish Housing — Glass-filled thermoplastic, black, 94V-0 rated Posts — Copper alloy, duplex plated .000030 [0.00076] gold on contact area, .000100-.000200 [0.00254-0.00508] matte tin on termination end, with entire post underplated .000050 [0.00127] nickel .110 [2.79] .120 [3.05] .
PAGE 23
AMPMODU Interconnection System Accessories: End Shrouds for Machine-Applied Posts Single-Row, .100 [2.54] Centers Part No. 102338-1 Mating Polarized Housing Material — Black thermoplastic, flame retardant .066 [1.68] .164 [4.17] .290 [7.37] End Shroud .712 [18.08] Board Mounted Straight Posts .050 [1.27] .059 [1.50] .350 Max. [8.89] PC Board Typical Assembly Break Line for 7 Pos. or Larger Header .066 [1.68] .029 [0.74] Dia.
PAGE 24
AMPMODU Interconnection System Accessories: Barrier Insert, Part No. 87743-1 Material .340 [8.64] .446 [11.33] .037 [0.94] Black polyester Technical Documents — page 276 The barrier insert can be used on double row headers (.100 x .100 [2.54 x 2.54] centers), including shrouded versions—3 and 4 sides, as well as unshrouded straight post headers.
PAGE 25
AMPMODU Interconnection System Accessories: Snap-In Polarizer for Low Profile Headers Material Black thermoplastic, flame retardant .134 [3.40] Part Numbers .335 [8.51] 499991-2 (Packaged 50 per bag) 499991-3 (Packaged 1000 per bag) Break Line (See below.) Related Product Data Low Profile Headers used with — pages 135-140 .335 [8.51] Break Line (See below.) .134 [3.40] The snap-in polarizer provides military polarization for low profile headers.
PAGE 26
AMPMODU Interconnection System Locking Clip Contacts and Housings Locking Clip Contacts and Housings Product Facts ■ Self-retaining contacts provide permanent connection with quick connect and disconnect ■ Fast, easy installation with no additional locking hardware required ■ Mates with .025 [0.64] square posts in a variety of configurations ■ Single- and double-row configurations in up to 20 positions on .100 [2.
PAGE 27
AMPMODU Interconnection System Locking Clip Contacts Wire Crimp Contacts with Insulation Support Body Material and Finish Contact Spring — Stainless steel Pating A — Selectively plated .000050 [0.00127] gold on contact area, with gold flash over .000050 [0.00127] nickel on entire contact Pating B — Selectively plated .000030 [0.00076] gold on contact area, with gold flash over .000050 [0.00127] nickel on entire contact Pating C — .000100-.000200 [0.00254-0.00508] bright tin over .000050 [0.
PAGE 28
AMPMODU Interconnection System Wire-Applied Housings for Locking Clip Contacts, Single-Row, .100 [2.54] Centerline Single-Row .060 [1.52] .700 [17.78] .350 .273 (Post 8.89 Length) 6.93 [ ] Material Glass-filled polyester, 94V-0 rated .145 [3.68] Related Product Data A Contacts — page 207 Mateable Headers and Posts — Refer to the Mating Post Selection Guide — page 90 .085 [2.16] .175 [4.44] C Typ. .100 Typ. [2.54] Technical Documents — pages 277, 278 Locking Clip Contacts and Housings .025 [0.
PAGE 29
AMPMODU Interconnection System Wire-Applied Housings for Locking Clip Contacts, Double-Row, .100 x .100 [2.54 x 2.54] Centerline Double-Row .300 [7.62] .700 [17.78] .350 Max. [8.89] (Post Length) Material Glass-filled polyester, 94V-0 rated .270 [6.86] Related Product Data .025 [0.64] Sq. Post (Shown for Ref. only) A .100 Typ. [2.54] .100 [2.54] Contacts — page 207 Mateable Headers and Posts — Refer to the Mating Post Selection Guide — page 90 .058 [1.
PAGE 30
AMPMODU Interconnection System Mod IV Wire-Applied Contacts and Housings Mod IV Wire-Applied Contacts and Housings Product Facts ■ Terminates 32-20 AWG [0.03-0.6mm2] discrete wire ■ Contacts have insulation support ■ Choice of three contact mating pressures ■ Available in a variety of gold and tin platings ■ Receptacles mate with .025 [0.
PAGE 31
AMPMODU Interconnection System Mod IV Pin and Receptacle Contacts Crimp Snap-In (No-strip) Receptacles and Crimp Snap-In Pins with Insulation Support (Standard Pressure) .058 [1.47] No-Strip Receptacle .470 [11.94] .165 [4.19] .016 [0.41] Gap Max. Pin with Insulation Support .815 [20.70] .068 [1.73] Crimp Snap-In (No-strip) Receptacles Ins. Dia. Range Finish .040-.055 [1.02-1.40] Plating A Plating C Part Nos.
PAGE 32
AMPMODU Interconnection System Mod IV Receptacle Contacts Crimp Snap-In Receptacles with Insulation Support (Standard, Intermediate and High Pressure) Standard Pressure A .058 [1.47] Material and Finish Mod IV Contacts Beryllium copper, phosphor bronze or copper-tin-phosphor bronze (see charts, on following page), plated as follows: Plating A — Duplex plated .000030 [0.00076] gold on contact area, .000100.000200 [0.00254-0.00508] tin on crimp area, with entire contact underplated .000050 [0.
PAGE 33
AMPMODU Interconnection System Mod IV Receptacle Contacts (Continued) Standard Pressure (Mod IV) Wire Size Range AWG [mm2] Ins. Dia. (Max.) Dimension A 32-27 0.03-0.1 .040 [1.02] .445 [11.30] 26-22 0.12-0.4 .061 [1.55] .445 [11.30] 24-20 0.2-0.6 .069 [1.75] .470 [11.94] Material Cu-Sn-Ph Bz Cu-Sn-Ph Bz Be Cu Be Cu Be Cu Cu-Sn-Ph Bz Cu-Sn-Ph Bz Cu-Sn-Ph Bz Cu-Sn-Ph Br Be Cu Be Cu Be Cu Be Cu Cu-Sn-Ph Bz Cu-Sn-Ph Bz Be Cu Be Cu Cu-Sn-Ph Br Be Cu Finish Hand Tool Part Nos.
PAGE 34
AMPMODU Interconnection System Mod IV Wire-Applied Housings, Single-Row, .100 [2.54] Centerline Non-Polarized .600 [15.24] Material Black thermoplastic, flame retardant .050 [1.27] Typ. Related Product Data Contacts — pages 211-213 Mateable Headers and Posts — pages 93-95, 101-103 .175 [4.45] A Max. .070 [1.78] Typ. B ±.003 [±0.08] .100 Typ. [2.54] C ±.003 [±0.08] .072 [1.83] .140 [3.
PAGE 35
AMPMODU Interconnection System Mod IV Wire-Applied Housings, Single-Row, .100 [2.54] Centerline (Continued) Recessed Area Polarized (with Detent Latching) .175 [4.45] A Material .050 Typ. [1.27] Black thermoplastic, flame retardant B ±.003 [±0.08] .071 [1.
PAGE 36
AMPMODU Interconnection System Mod IV Wire-Applied Housings, Double-Row, .100 x .100 [2.54 x 2.54] Centerline Non-Polarized .175 [4.45] A Material Black thermoplastic, flame retardant .100 Typ. [2.54] .050 [1.27] Typ. .240 [6.10] B X C .100 [2.54] R Optional Related Product Data Contacts — pages 211-213 Mateable Headers and Posts — pages 96-99, 104, 105, 117-120 Mod IV Wire-Applied Housings .070 [1.78] No. of Pos.
PAGE 37
AMPMODU Interconnection System Mod IV Wire-Applied Housings, Double-Row, .100 x .100 [2.54 x 2.54] Centerline (Continued) Strain Relief Locators (on Housings 20 Positions and Larger) Polarized .175 [4.45] Material Black thermoplastic, flame retardant A ±.003 B [±0.08] Related Product Data .100 [2.54] Typ. Contacts — pages 211-213 Mateable Headers and Posts— pages 117-131 C ±.003 [±0.08] .100 [2.54] X Typ. .050 [1.27] Typ. .600 [15.24] .070 Typ. [1.78] R Optional .240 [6.
PAGE 38
AMPMODU Interconnection System Mod IV Wire-Applied Housings, Double-Row, .100 x .100 [2.54 x 2.54] Centerline (Continued) Polarized (with Detent Latching, with and without Strain Relief/Pull Tab) Strain Relief Locators (on Housings 20 Positions and Larger) .175 [4.45] A Material B ±.003 C ±.003 [±0.08] Black thermoplastic, flame retardant [±0.08] .100 Typ. [2.54] .100 Typ. [2.54] Related Product Data .050 [1.27] Typ.
PAGE 39
AMPMODU Interconnection System Mod IV Wire-Applied Housings, Double-Row, .100 x .100 [2.54 x 2.54] Centerline (Continued) Dimensions No. of Pos. A .900 [22.86] 1.000 [25.40] 1.100 [27.94] 1.200 [30.48] 1.300 [33.02] 1.400 [35.56] 1.500 [38.10] 1.600 [40.64] 1.700 [43.18] 1.800 [45.72] 1.900 [48.26] 2.000 [50.80] 2.100 [53.34] 2.200 [55.88] 2.400 [60.96] 2.500 [63.50] 2.600 [66.04] 2.700 [68.58] 2.900 [73.66] 3.000 [76.20] 3.200 [81.28] 3.300 [83.82] 3.500 [88.90] 3.800 [96.52] B C .400 [10.16] .
PAGE 40
AMPMODU Interconnection System Mod IV Wire-Applied Housings, Double-Row, .100 x .100 [2.54 x 2.54] Centerline (Continued) Center Polarized Position No. 1 Indicator .030 [0.76] .150† [3.81] .570 [14.88] .130 [3.30] .130 [3.30] B A Material Black thermoplastic, flame retardant Related Product Data Mod IV Wire-Applied Housings Contacts — pages 211-213 Mateable Headers and Posts — AMP-LATCH Low Profile Headers, Shrouded — pages 135-140 .120 [3.05] C .072 [1.83] X .285 [7.24] .227 [5.77] X .
PAGE 41
AMPMODU Interconnection System Short Point, Crimp Snap-In Wire-Applied Contacts and Housings Product Facts Short point of contact mates with .169 [4.29] to .259 [6.58] long post ■ Double-row housings are end-to-end and side-to-side stackable ■ Terminates 32-20 AWG [0.03-0.6 mm2] discrete wire ■ Contacts have insulation support to accept a maximum insulation diameter of .060 [1.52] ■ Available with .000015 [0.00038] or .000030 [0.00076] gold duplex, or tin plating ■ Mates with .025 [0.
PAGE 42
AMPMODU Interconnection System Short Point Crimp Snap-In Receptacle Contacts Material and Finish .068 [1.73] Copper alloy C7025, plated as follows: Plating A — Duplex plated .000030 [0.00076] min. gold on contact area, .000050 [0.00127] min. tin in crimp area, with entire contact underplated .000050 [0.00127] min. nickel Plating B — Duplex plated .000015 [0.00038] min. gold on contact area, .000050 [0.00127] min. tin in crimp area, with entire contact underplated .000050 [0.00127] min.
PAGE 43
AMPMODU Interconnection System Short Point Wire-Applied Housings, Double-Row, Non-Polarized, .100 x .100 [2.54 x 2.54] Centerline A Material Black thermoplastic, flame retardant, 94V-0 rated Related Product Data Performance Characteristics — page 221 Contacts — page 222 Mateable Headers — pages 104, 105 B .049 [1.24] X .049 [1.24] 2 Plc. .036 [0.91] .600 [15.24] .198 [5.03] .100 [2.54] .100 [2.54] Typ. 0.72 [1.
PAGE 44
AMPMODU Interconnection System Short Point Wire-Applied Housings, Double-Row, Polarized, .100 x .100 [2.54 x 2.54] Centerline A Material Black thermoplastic, flame retardant, 94V-0 rated .100 [2.54] .049 [1.24] Short Point Wire-Applied Housings .049 [1.24] 2 Plc. X Related Product Data Performance Characteristics — page 221 Contacts — page 222 Mateable Headers — pages 104, 105, 135-138 .100 [2.54] .600 [15.24] .095 [2.41] .036 [0.91] .198 [5.03] .100 [2.54] .100 [2.54] Typ. 0.72 [1.
PAGE 45
AMPMODU Interconnection System MTE Interconnection System Product Facts Receptacle assemblies mate with .025 [0.64] sq. posts; mating post length is .200 [5.08] min., .250 [6.35] max. ■ Proven AMPMODU receptacle contact design; dual cantilever beams, built-in anti-overstress, completely enclosed “box” design, standard or high-pressure ■ Insulation displacement technology ■ Two contact sizes for terminating 30-22 AWG [0.050.3 mm2] wire range; .054 [1.37] max.
PAGE 46
AMPMODU Interconnection System MTE Interconnection System (Continued) Wire-to-Board Receptacle Assemblies with Guide Ribs (See pages 232 & 233) High-Temp Headers, Polarized/Latching, Straight and Right Angle Post, with or without Holddown 2 (See pages 249 & 250) Receptacle Assemblies Polarized/Latching (See pages 230 & 231) Double-Row Coupling Shroud (See page 241) Receptacle Assemblies, Polarized/Latching (See pages 230 & 231) AMPMODU Shrouded Headers, Double-Row, Straight or Right Angle Post1 (See p
PAGE 47
AMPMODU Interconnection System MTE Interconnection System (Continued) Wire-to-Wire Pin Assemblies, Shrouded Polarized/Latching (See pages 236 & 237) Receptacle Assemblies, Polarized/Latching (See pages 230 & 231) Receptacle Contact, Insulation Displacement (Used in all Receptacle Assemblies) Pin Contact, Insulation Displacement (Used in all Pin Assemblies) Pin Assemblies with Guide Ribs (See pages 238 & 239) Panel Mount Pin Shroud (See page 242) MTE Interconnection System Receptacle Assemblies Singl
PAGE 48
AMPMODU Interconnection System MTE Receptacle Assemblies—Plain, Single-Row, .100 [2.54] Centerline Receptacle Contacts (See Note 1) .520 [13.21] 1.120 [28.45] Preassembled housings in strip form are available in positions 2 thru 12. For ease of handling, positions 2 thru 5 are recommended when using the Tyco Electronics Manual Pistol Grip Tool.
PAGE 49
AMPMODU Interconnection System MTE Receptacle Assemblies—Strip Form Plain, Single-Row, .100 [2.54] Centerline (Continued) Dimensions No. of Pos. 2 3 4 5 6 7 8 9 10 11 12 A B 2.000 [50.80] .198 [5.03] 2.400 [60.96] .298 [7.57] 1.990 [50.55] .398 [10.11] 1.990 [50.55] .498 [12.65] 2.390 [60.71] .598 [15.19] 1.400 [35.56] .698 [17.73] 1.600 [40.64] .798 [20.27] 1.800 [45.72] .898 [22.81] 2.000 [50.80] .998 [23.35] 2.200 [55.88] 1.098 [27.89] 2.400 [60.96] 1.198 [30.
PAGE 50
AMPMODU Interconnection System MTE Receptacle Assemblies—Polarized/Latching, Single-Row, .100 [2.54] Centerline Receptacle Contacts (See Note 1) .520 [13.21] Preassembled housings in strip form are available in positions 2 thru 12. For ease of handling, positions 2 thru 5 are recommended when using the Tyco Electronics Manual Pistol Grip Tool. 1.120 [28.45] .600 [15.
PAGE 51
AMPMODU Interconnection System MTE Receptacle Assemblies—Strip Form Polarized/Latching, Single-Row, .100 [2.54] Centerline (Continued) Dimensions No. of Pos. 2 3 4 5 6 7 8 9 10 11 12 A B 2.000 [50.80] .198 [5.03] 2.400 [60.96] .298 [7.57] 1.990 [50.55] .398 [10.11] 1.990 [50.55] .498 [12.65] 2.390 [60.71] .598 [15.19] 1.400 [35.56] .698 [17.73] 1.600 [40.64] .798 [20.27] 1.800 [45.72] .898 [22.81] 2.000 [50.80] .998 [23.35] 2.200 [55.88] 1.098 [27.89] 2.400 [60.96] 1.198 [30.
PAGE 52
AMPMODU Interconnection System MTE Receptacle Assemblies—Guide Ribs, Single-Row, .100 [2.54] Centerline Receptacle Contacts (See Note 1) .520 [13.21] Preassembled housings in strip form are available in positions 2 thru 12. For ease of handling, positions 2 thru 5 are recommended when using the Tyco Electronics Manual Pistol Grip Tool. 1.120 [28.45] .600 [15.
PAGE 53
AMPMODU Interconnection System MTE Receptacle Assemblies—Strip Form with Guide Ribs, Single-Row, .100 [2.54] Centerline (Continued) Dimensions No. of Pos. 2 3 4 5 6 7 8 9 10 11 12 A B 2.000 [50.80] .198 [5.03] 2.400 [60.96] .298 [7.57] 1.990 [50.55] .398 [10.11] 1.990 [50.55] .498 [12.65] 2.390 [60.71] .598 [15.19] 1.400 [35.56] .698 [17.73] 1.600 [40.64] .798 [20.27] 1.800 [45.72] .898 [22.81] 2.000 [50.80] .998 [23.35] 2.200 [55.88] 1.098 [27.89] 2.400 [60.96] 1.198 [30.
PAGE 54
AMPMODU Interconnection System MTE High Pressure Receptacle Assemblies—Plain, Single-Row, .100 [2.54] Centerline Receptacle Contacts (See Note 1) .520 [13.21] 1.120 [28.45] Preassembled housings in strip form are available in positions 2 thru 12. For ease of handling, positions 2 thru 5 are recommended when using the Tyco Electronics Manual Pistol Grip Tool. .600 [15.24] Material and Finish B Typ.
PAGE 55
AMPMODU Interconnection System MTE High Pressure Receptacle Assemblies – Guide Ribs Receptacle Contacts (See Note 1) .520 [13.21] 1.120 [28.45] Preassembled housings in strip form are available in positions 2 thru 12. For ease of handling, positions 2 thru 5 are recommended when using the Tyco Electronics Manual Pistol Grip Tool. .600 [15.24] B Typ. Material and Finish A Housing — Thermoplastic, black, 94V-0 rated Contacts — Phosphor Bronze, duplex plated .000030 [0.00076] gold on contact area, .
PAGE 56
AMPMODU Interconnection System MTE Pin Assemblies, Shrouded—Polarized/Latching, Single-Row, .100 [2.54] Centerline Pin Contacts (See Note 1) .520 [13.21] Preassembled housings in strip form are available in positions 2 thru 12. For ease of handling, positions 2 thru 5 are recommended when using the Tyco Electronics Manual Pistol Grip Tool. 1.470 [37.
PAGE 57
AMPMODU Interconnection System MTE Pin Assemblies, Shrouded—Strip Form Polarized/Latching, Single-Row, .100 [2.54] Centerline (Continued) Dimensions No. of Pos. 2 3 4 5 6 7 8 9 10 11 12 A B 2.360 [59.94] .295 [7.49] 1.980 [50.29] .395 [10.03] 1.980 [50.29] .495 [12.57] 2.380 [60.45] .595 [15.11] 1.390 [35.31] .695 [17.65] 2.390 [60.71] .795 [20.19] 1.790 [45.47] .895 [22.73] 1.990 [50.57] .995 [25.27] 2.190 [55.63] 1.095 [27.81] 2.390 [60.71] 1.195 [30.35] 2.590 [65.79] 1.295 [32.
PAGE 58
AMPMODU Interconnection System MTE Pin Assemblies—Guide Ribs, Single-Row, .100 [2.54] Centerline Pin Contacts (See Note 1) .520 [13.21] Preassembled housings in strip form are available in positions 2 thru 12. For ease of handling, positions 2 thru 5 are recommended when using the Tyco Electronics Manual Pistol Grip Tool. Material and Finish MTE Pin Assemblies Housing — Black thermoplastic, 94V-0 rated Contacts — Phosphor Bronze, plated as follows: Plating A — Duplex plated .000030 [0.
PAGE 59
AMPMODU Interconnection System MTE Pin Assemblies—Strip Form with Guide Ribs, Single-Row, .100 [2.54] Centerline (Continued) Dimensions No. of Pos. A 2 3 4 5 6 7 8 9 10 11 12 1.980 [50.29] 1.490 [37.85] 1.990 [50.55] 1.990 [50.55] 2.390 [60.71] 1.400 [35.56] 1.600 [40.64] 1.800 [45.72] 2.000 [50.80] 2.200 [55.88] 2.400 [60.96] B 0.198 [5.03] 0.298 [7.57] 0.398 [10.11] 0.498 [12.65] 0.598 [15.19] 0.698 [17.73] 0.798 [20.27] 0.898 [22.81] 0.998 [25.35] 1.098 [27.89] 1.198 [30.
PAGE 60
AMPMODU Interconnection System Coupling Shrouds for MTE Receptacle Assemblies with Guide Ribs Single-Row .307 [7.80] A Material Black thermoplastic, 94V-0 rated .582 [14.78] Technical Documents — pages 277, 278 No. of Pos. 4 5 6 7 8 9 10 11 12 13 14 Dimension A .485 [12.32] .585 [14.86] .685 [17.40] .785 [19.94] .885 [22.48] .985 [25.02] 1.085 [27.56] 1.185 [30.10] 1.285 [32.64] 1.385 [35.18] 1.485 [37.
PAGE 61
AMPMODU Interconnection System Coupling Shrouds for MTE Receptacle Assemblies with Guide Ribs (Continued) Double-Row Material .735 [18.67] Black thermoplastic, 94V-0 rated Technical Documents — Position No. 1 Identification pages 277, 278 A Product Specification 108-25034 Application Specification 114-25026 Dimension A .585 [14.86] .685 [17.40] .785 [19.94] .885 [22.48] .985 [25.02] 1.085 [27.56] 1.185 [30.10] 1.285 [32.64] 1.385 [35.18] 1.485 [37.72] 1.585 [40.26] 1.685 [42.80] 1.785 [45.34] 1.
PAGE 62
AMPMODU Interconnection System Panel Mount Pin Shrouds for MTE Pin Assemblies with Guide Ribs, Single-Row Material .310 [7.87] Black thermoplastic, 94V-0 rated A .250 [6.35] Technical Documents — pages 277, 278 Product Specification 108-25034 Application Specification 114-25026 .990 [25.15] Position No. 1 Identification MTE Panel Mount Pin Shrouds .320 [8.13] .270 [6.86] .320 [8.13] B 5 No. of Pos. 2 3 4 5 6 7 8 9 10 11 12 13 Dimensions A B .735 [18.67] .625 [15.88] .835 [21.21] .725 [18.42] .
PAGE 63
AMPMODU Interconnection System Panel Mount Pin Shrouds for MTE Pin Assemblies with Guide Ribs, Single-Row (Continued) Material Black thermoplastic, 94V-0 rated Technical Documents — pages 277, 278 Pin Assembly with Guide Ribs (Refer to pages 238 & 239) Product Specification 108-25034 Application Specification 114-25026 Panel Mount Pin Shroud Receptacle Assemblies with Guide Ribs, Installed in Single-Row Coupling Shroud (Refer to pages 232, 233, 235 & 240) Rear of Panel MTE Panel Mount Pin Shrouds Rec
PAGE 64
AMPMODU Interconnection System MTE Headers, Shrouded Polarized/Latching, Single-Row .100 [2.54] Centerline .025 [0.64] Square Straight Post (With or Without Swaged Tail) .535 [13.59] Swaged Retention Tail (See Note) Position No. 1 Indicator A Material and Finish Housing — Black thermoplastic, 94V-0 rated Posts — Brass, plated as follows: Plating A — Duplex plated .000030 [0.00076] gold on contact area, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.
PAGE 65
AMPMODU Interconnection System MTE Headers, Shrouded Polarized/Latching, Single-Row .100 [2.54] Centerline (Continued) A .300 [7.62] .400 [10.16] .500 [12.70] .600 [15.24] .700 [17.78] .800 [20.32] .900 [22.86] 1.000 [25.40] 1.100 [27.94] 1.200 [30.48] 1.300 [33.02] 1.400 [35.56] 1.500 [38.10] 1.600 [40.64] 1.700 [43.18] 1.800 [45.72] 1.900 [48.26] 2.000 [50.80] 2.100 [53.34] 2.200 [55.88] 2.300 [58.42] 2.400 [60.96] 2.500 [63.50] 2.600 [66.04] Dimensions B C .220 [5.59] .100 [2.54] .320 [8.13] .200 [5.
PAGE 66
AMPMODU Interconnection System MTE Headers, Shrouded Latching, Single-Row .100 [2.54] Centerline .025 [0.64] Square Right-Angle Post With Holddown .535 [13.59] Position No. 1 Indicator A B C Material and Finish MTE Headers Housing — Black thermoplastic, 94V-0 rated Posts — Brass, plated as follows: Plating A — Duplex plated .000030 [0.00076] gold on contact area, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] nickel Plating B — Duplex plated .000015 [0.
PAGE 67
AMPMODU Interconnection System MTE Headers, Shrouded Latching, Single-Row .100 [2.54] Centerline (Continued) No. of Pos. 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 A .300 [7.62] .400 [10.16] .500 [12.70] .600 [15.24] .700 [17.78] .800 [20.32] .900 [22.86] 1.000 [25.40] 1.100 [27.94] 1.200 [30.48] 1.300 [33.02] 1.400 [35.56] 1.500 [38.10] 1.600 [40.64] 1.700 [43.18] 1.800 [45.72] 1.900 [48.26] 2.000 [50.80] 2.100 [53.34] 2.200 [55.88] 2.300 [58.42] 2.400 [60.96] 2.500 [63.50] 2.
PAGE 68
AMPMODU Interconnection System MTE Headers, Shrouded Latching, Single-Row .100 [2.54] Centerline .025 [0.64] Square Straight Post (With Swaged Tails and PC Board Orientation) .535 [13.59] Swaged Retention Tail (See Note) Position No. 1 Indicator Housing — Black thermoplastic, 94V-0 rated Posts — Brass, plated .000100 [0.00254] tin over .000050 [0.00127] nickel on entire post .120 [3.05] MTE Headers .070 [1.78] X .100 [2.54] .050 [1.27] Dia. .260 [6.60] .200 [5.08] .060 [1.
PAGE 69
AMPMODU Interconnection System MTE Headers, Through-hole, Surface Mount Compatible, Shrouded Polarized/Latching, Single-Row .100 [2.54] Centerline .025 [0.64] Square Straight Post (With Swaged Tails and PC Board Orientation) .535 [13.59] Swaged Retention Tail (See Note) Position No. 1 Indicator A B Material and Finish C Housing — Black thermoplastic, 94V-0 rated Posts — Brass, duplex plated .000015 [0.00038] gold on contact area, .000100 [0.00254] min tin on solder tail, with entire post underplated .
PAGE 70
AMPMODU Interconnection System MTE Headers, Polarized/Latching, Through-Hole, Surface Mount Compatible, Single-Row, .100 [2.54] Centerline .025 [0.64] Square Right-Angle Post (With Holddown) .535 [13.59] Position No. 1 Indicator Material and Finish Housing — Black thermoplastic, 94V-0 rated Posts — Brass, duplex plated .000015 [0.00038] gold on contact area, .000100 [0.00254] min. tin on solder tail, with entire post underplated .000050 [0.00127] nickel .230 [5.84] A .060 [1.52] (2 Plc.) B C .
PAGE 71
AMPMODU Interconnection System MTE Headers, Right-Angle, Polarized/Latching, Surface Mount E .025 [0.64] Typ. .120 [3.05] Ø.085±.002 [2.16±0.05] .065 Min Pad on [1.65] Underside 2 Plc .140 [3.56] .535 [13.59] Material and Finish Housing — Black thermoplastic, 94V-0 rated Posts — Brass, plated as follows: Plating A — Duplex plated .000030 [.00076] gold on contact area, .000100 [.00254] min. tin on solder area, with entire post underplated .000050 [.00127] nickel. Plating B — Duplex plated .000015 [.
PAGE 72
AMPMODU Interconnection System MTE Headers, Vertical, Polarized/Latching, Surface Mount E .075 [1.90] .025 Typ. [0.62] .535 [13.59] .313 [7.62] Material and Finish MTE Headers Housing — Black thermoplastic, 94V-0 rated Posts — Brass, plated as follows: Plating A — Duplex plated .000030 [.00076] gold on contact area, .000100 [.00254] min. tin on solder area, with entire post underplated .000050 [.00127] nickel. Plating B — Duplex plated .000015 [.00038] gold on contact area, .000100 [.00254] min.
PAGE 73
AMPMODU Interconnection System Interchangeable Contacts, Wire Crimp (Snap-In) Material and Finish Short Point Receptacles .068 [1.73] Copper alloy C7025, plated as follows: Plating A — Duplex plated .000030 [0.00076] min. gold on contact area, .000050 [0.00127] min. tin in crimp area, with entire contact underplated .000050 [0.00127] min. nickel Plating B — Duplex plated .000015 [0.00038] min. gold on contact area, .000050 [0.00127] min. tin in crimp area, with entire contact underplated .000050 [0.
PAGE 74
AMPMODU Interconnection System Interchangeable Contacts, Wire Crimp (Snap-In) (Continued) Material and Finish Pins Phosphor bronze, plated as follows: Plating A — Duplex plated .000030 [0.00076] gold on contact area, .000030 [0.00076] min. tin in crimp area, with entire contact underplated .000050 [0.00127] nickel Plating B — Duplex plated .000015 [0.00038] gold on contact area, .000030 [0.00076] min. tin on solder area, with entire contact underplated .000050 [0.00127] nickel Plating C — .000100 [0.
PAGE 75
AMPMODU Interconnection System MT and Shielded MT Interconnection System Product Facts Full line of mass termination tooling offers lowest installed cost for most production needs ■ Dual cantilever beams with anti-overstress features provide redundant contact of mating post and limit beam deflection, preventing permanent deformation ■ Redundant insulation displacement slots provide for maximum reliability ■ Integral wire strain relief on contact can prevent wire motion from being transmitted to wire
PAGE 76
AMPMODU Interconnection System MT Receptacle Assemblies, Double-Row .100 x .100 [2.54 x 2.54] Centerline Housings Pre-loaded with Standard Pressure Contacts Contact I.D. No. 1 1 1 1 1 .125 [3.18] 1 .600 [15.24] .270 [6.86] 1 Circuit No. 1 Identifier A Max. Material and Finish Housing — Glass-filled thermoplastic, black, 94V-0 rated Contacts — Copper alloy, duplex plated .000030 [0.00076] gold in mating area, .000050 [0.00127] tin on solder tail, with entire contact underplated .000050 [0.
PAGE 77
AMPMODU Interconnection System MT Receptacle Assemblies, Double-Row .100 x .100 [2.54 x 2.54] Centerline (Continued) Housings Pre-loaded with High Pressure Contacts Contact I.D. No. 4 4 4 4 4 4 4 4 4 4 .125 [3.18] .600 [15.24] .270 [6.86] 1 Material and Finish A Max. Housing — Glass-filled thermoplastic, black, 94V-0 rated Contacts — Copper alloy, duplex plated .000030 [0.00076] gold in mating area, .000050 [0.00127] tin on solder tails, with entire contact underplated .000050 [0.
PAGE 78
AMPMODU Interconnection System Low Profile Covers for Double-Row MT Receptacle Assemblies Material Front Covers Black thermoplastic, flame retardant A - Polarizing Cover (Mates with AMPMODU 4-sided shrouded headers. Refer to pages 117, 122, 126, 130.) Related Product Data For use on Double-Row MT Receptacle Assemblies — pages 256, 257 B - Latching Cover (Mates with AMPMODU 4-sided shrouded headers with extraction slot. Refer to pages 117, 122, 126, 130.) .750 [19.05] .750 [19.
PAGE 79
AMPMODU Interconnection System Standard Profile Covers for Double-Row MT Receptacle Assemblies Material Black thermoplastic, flame retardant G - Hermaphroditic Cover (Two hermaphroditic covers can be used or one hermaphroditic cover can be used with an H Ejection Cover.) Related Product Data 1.120 Assembled* [28.45] For use on Double-Row MT Receptacle Assemblies — pages 256, 257 .850 [21.
PAGE 80
AMPMODU Interconnection System Shielding Hardware and Accessories for MT Interconnection System MT Shielding Hardware and Accessories Product Facts ■ Add-on shielding accessories for existing AMPMODU Standard MT and PC board mounted headers ■ Compact design ■ Tin plated copper alloy material ■ Redundant cantilever beams provide for good peripheral contact, eliminating the need for a separate RF gasket ■ Polarized mating ■ 360° cable braid termination with cable jacket support ■ Cable shieldi
PAGE 81
AMPMODU Interconnection System Shielding Hardware and Accessories for Double-Row MT Receptacle Assemblies Two-Piece Shields— Straight Exit Outer Shell Half Material and Finish Shell Halves — Copper alloy, .020 [0.51] thick; pretinned .000030 [0.00076] min. A C Related Product Data Double-Row MT Receptacle Assemblies — pages 256, 257 Non-Polarizing Covers (Part No. Series 102541 with back cover 102536 or 102823) — pages 258, 259 Shield Ferrules — page 263 B .326 [8.
PAGE 82
AMPMODU Interconnection System Shielding Hardware and Accessories for Double-Row MT Receptacle Assemblies (Continued) Two-Piece Shields— Right-Angle Exit .125 Dia. [3.18] (See Note 2) Material and Finish C Outer Shell Half Shell Halves — Copper alloy, .020 [0.51] thick; pretinned .000030 [0.00076] min. A Related Product Data Double-Row MT Receptacle Assemblies — pages 256, 257 Non-Polarizing Covers (Part No.
PAGE 83
AMPMODU Interconnection System Shielding Hardware and Accessories for Double-Row MT Receptacle Assemblies (Continued) Ferrules for Shielding Kits Material and Finish Soft copper, tin plated Related Product Data Used with Shielding Kits — pages 261, 262 Technical Documents — pages 277, 278 Product Specification 108-25015, 108-25018, 108-25030 Application Specification 114-25032 Instruction Sheet 408-6532 Application Tooling 6 Straight-Exit Shields Outer Inner 102988-2 102987-6 10 103137-2 103136-2
PAGE 84
AMPMODU Interconnection System Shielded MT Headers for use with Shielded MT Receptacle Assemblies AMPMODU Right-Angle Headers PC Board Mounted .755 [19.18] C Material and Finish Housing — Black thermoplastic, flame retardant Posts — Copper alloy, plated .000030 [0.00076] gold over .000050 [0.00127] nickel on entire post Shield — Copper alloy, .020 [0.51] thick; pretinned .000030 [0.00076] min. .460 [11.68] Shield Right-Angle Header B .550 [13.97] .125 [3.
PAGE 85
AMPMODU Interconnection System Replacement MT Receptacle Contacts Insulation Displacement Contacts Contact Identification Material and Finish Copper alloy, duplex plated .000030 [0.00076] gold in mating area, .000100.000200 [0.00254-0.00508] tin in crimp area, with entire contact underplated .000050 [0.00127] nickel .050 Max. [1.
PAGE 86
AMPMODU Interconnection System Mini-Tandem Spring Receptacle Housings and Contacts Mini Tandem Spring Housings and Contacts Product Facts ■ Individual contacts mate with .025 [0.64] sq. posts, .125 [3.18] long ■ Crimp snap-in contacts accept 32-22 AWG [0.03-0.32 mm2] wire ■ Retention latch provides for positive installation ■ No insertion tool required ■ High durability design provides long life ■ Available with .000015 [0.00038] or .000030 [0.
PAGE 87
AMPMODU Interconnection System Mini-Tandem Spring Housings, Single-Row .100 [2.54] Centerline .550 [13.97] .030 [0.76] Material — Black glass-filled polyester, 94V-0 rated .036 [0.91] .066 [1.68] Technical Documents — pages 277, 278 .050 [1.27] Product Specification 108-25031 Application Specification 114-25021 .100 [2.54] .100 Max. [2.54] A Max. B Spaces @ .100 [2.54] = C .050 [1.27] Minimum mating post length is .140 [3.55]. Spring Housings 5 No. of Pos. 2 4 8 12 16 18 20 22 A .200 [5.
PAGE 88
AMPMODU Interconnection System Mini-Tandem Spring Housings, Double-Row .100 [2.54] Centerline .550 [13.97] .030 [0.76] .036 [0.91] Material — Black glass-filled polyester, 94V-0 rated* .066 [1.68] Technical Documents — A Max. pages 277, 278 Product Specification 108-25031 .200 [5.08] Application Specification 114-25021 .100 [2.54] B Spaces @ .100 [2.54] = C .050 [1.27] .100 Max. [2.54] Mini-Tandem Spring Contacts Minimum mating post length is .140 [3.55].
PAGE 89
AMPMODU Interconnection System Mini-Tandem Spring Contacts Receptacle Contacts .060 [1.52] Material and Finish Phosphor bronze, plated as follows: Plating A — Duplex plated .000030 [0.00076] gold inlay on contact area, matte tin in crimp area, with entire contact underplated .000050 [0.00127] nickel Plating B — Duplex plated .000015 [0.00038] gold inlay on contact area, matte tin in crimp area, with entire contact underplated .000050 [0.00127] nickel Plating C — Duplex plated .000050 [0.
PAGE 90
AMPMODU Interconnection System Application Tooling for Wire Crimp Contacts Tooling shown on this page is designed to terminate wire crimp contacts used in various AMPMODU wire-toboard connectors. Refer to page 88 to determine the applicable connectors. AMP-O-LECTRIC Model “G” Terminating Machine (Shown with Optional Crimp Force Monitor) A totally new design of our most popular machine for bench-top operation.
PAGE 91
AMPMODU Interconnection System Application Tooling for Wire Crimp Contacts (Continued) AMP 3K/40 and AMP 5K/40 Terminators As a value oriented terminator, the AMP 3K/40 and AMP 5K/40 are designed for customers that require the increased output and quality of a semiautomatic machine at a competitive price.
PAGE 92
AMPMODU Interconnection System Application Tooling for Wire Crimp Contacts (Continued) Tooling shown on this page is designed to terminate wire crimp contacts used in various AMPMODU wire-toboard connectors. Refer to page 88 to determine the applicable connectors. AMPOMATOR System III Leadmaker The AMPOMATOR System III is an automatic machine for the production of terminated wire leads.
PAGE 93
AMPMODU Interconnection System Application Tooling for Insulation Displacement Crimp (IDC) Contacts and Connectors Tooling shown on this page is designed to terminate IDC contacts for various AMPMODU wire-to-board connectors. Refer to page 88 to determine the applicable connectors.
PAGE 94
AMPMODU Interconnection System Application Tooling for Insulation Displacement Crimp (IDC) Contacts and Connectors (Continued) Tooling shown on this page is designed to terminate IDC contacts for various AMPMODU wire-to-board connectors. Refer to page 88 to determine the applicable connectors. Tube-Fed Ribbon Cable Machine Tube-Fed Ribbon Cable Machine No. 856002-1 Application Tooling Designed for bench applications, this machine is pneumatically operated and controlled by a foot pedal.
PAGE 95
AMPMODU Interconnection System Application Tooling for Insulation Displacement Crimp (IDC) Contacts and Connectors (Continued) Tooling shown on this page is designed to terminate IDC contacts for various AMPMODU wire-to-board connectors. Refer to page 88 to determine the applicable connectors. CHAMPOMATOR Model 2.5 Terminating Machine No. 354786-(*) This compact bench machine terminates wires manually sorted from multiconductor cables.
PAGE 96
AMPMODU Interconnection System Technical Documents for Board-to-Board Products Technical Documents Various technical documents are available for your use. Product Specifications describe technical performance characteristics and verification tests. They are intended for the Design, Component and Quality Engineers.
PAGE 97
AMPMODU Interconnection System Technical Documents for Wire-to-Board Products Various technical documents are available for your use. Product Specifications describe technical performance characteristics and verification tests. They are intended for the Design, Component and Quality Engineers. Locking Clip Contacts and Housings — Pages 206-209: 108-36028 Connector, Locking Clip, .025 [0.64] Square, Gold 108-36028-1 Connector, Locking Clip, .025 [0.64] Square, Tin Mod.
PAGE 98
AMPMODU Interconnection System Technical Documents for Wire-to-Board Products (Continued) Instruction Sheets provide instructions for assembling or applying the product. They are intended for the Manufacturing Assembler or Operator.