User Manual

Notes about record styluses
o Record styluses are precision parts, so handle them carefully
to avoid bending or damaging their tips. If a stylus becomes
bent or damaged, it might not be able to follow the audio
groove precisely and could damage records or cause other
malfunction.
o If a stylus becomes dirty, use a commercially available stylus
cleaner or similar product to clean it.
Replacing the stylus
If the tip of the stylus becomes worn, not only will it worsen
the sound quality, it could also damage records. After about
400 hours of playback time, replace the stylus with one that
we specify.
Please use an Audio-Technica ATN3600L replacement stylus.
o An Audio-Technica AT3600L VM Type cartridge is installed
in this unit.
o Follow the replacement instructions in the manual of the
replacement stylus.
ATTENTION
o Before replacing the stylus, turn this unit and the amplifier
off. Failure to do so could cause sudden loud noises that
might damage speakers.
o Be careful not to hurt your hand or the equipment.
o Be careful not to allow small children to accidentally swallow
styluses.
o Be aware that bent styluses, for example, that result from
insufficient customer caution or an outside cause are not
covered by the warranty.
To remove old stylus, hold the cartridge in one hand, grasp
the plastic stylus housing with thumb and forefinger, and pull
diagonally down away from the cartridge. The stylus assembly
comes away at a slight angle.
To install replacement stylus, insert the new stylus assembly
into the cartridge at a slight angle, so the hook at the end of
the stylus fits into the slot in the cartridge body. The stylus
assembly should click into place when fully seated on the car-
tridge. The stylus must be fully seated on the body for proper
operation.
Replacement stylus (sold on the market):
Audio-Technica ATN3600L
Listening with Bluetooth® speakers
This unit has a Bluetooth transmitter that can send sound to
Bluetooth speakers wirelessly.
1 Press the STANDBY/ON button on the
back of the unit to turn it on.
2 Pair and connect the Bluetooth
speakers.
PAIRING button/
Pairing lamp
Pairing Bluetooth speakers
Pairing this unit with another Bluetooth speaker is nec-
essary the first time you connect with that Bluetooth
speaker.
1) Press the PAIRING button on this unit to start connec-
tion mode.
The pairing lamp will blink slowly.
2) Press the PAIRING button again for at least two sec-
onds to start pairing mode.
The pairing lamp (white) will blink rapidly.
3) After this unit enters pairing mode, put the Bluetooth
speaker into pairing mode.
When this unit and the Bluetooth speaker are connected,
the pairing lamp will stay lit without blinking.
o Refer to the operation manual of the Bluetooth
speaker for information about how to use it.
o Pairing might take some time depending on the con-
nected Bluetooth speaker.
o This unit will connect to the closest Bluetooth
speaker. If no Bluetooth speaker is found for about
five minutes, Bluetooth standby mode will begin and
the pairing lamp will become unlit.
Connecting already paired Bluetooth
speakers
Press the PAIRING button on this unit to start connection
mode.
The pairing lamp will blink slowly.
When this unit and the Bluetooth speaker are connected,
the pairing lamp will stay lit without blinking.
o When connecting to a Bluetooth speaker, move
other Bluetooth speakers and receiving devices at
least 10 meters (33 ft.) away from this unit or turn
them off.
3 Play a record.
o Bluetooth connection is also possible while a record
is playing.
o Adjust the Bluetooth speaker volume if necessary.
o This unit cannot be used to adjust the volume.
o To end a connection, press the PAIRING button on
this unit for at least six seconds to enter Bluetooth
standby mode or turn this unit off.
o Pressing the PAIRING button for ten or more seconds
will cause the pairing lamp to blink and clear all exist-
ing pairings with other devices.
ATTENTION
When you will not use this unit, end the Bluetooth connection
by pressing this unit’s PAIRING button for at least six seconds.
Then, confirm that the pairing lamp has turned off.
8