Owner's Manual

ManualsBrandsTEAC ManualsHome AudioTEAC TN-280BT

1

2

3

4

5

6

7

8

9

Keep

the

unit

In

standby

while

setting

It

up

( I!]

on

page

5).

n Place

It

on a flat surface.

Since

the

heights

of

this

unit's

feet

cannot

be

adjusted,

be

sure

to

place

it

on

a

flat

surface.

fl

Install

the

turntable (platter).

n

6

Align

the

turntable

(platter)

with

the

center

shaft

and

Install

it

Loop

the

belt around

the

motor

pulley.

The

rubber

belt

Is

wrapped

around

the

sub-platter.

Use

a

finger

to

pull

the

rubber

belt

through

the

round

opening

and

loop It

around

the

motor

pulley.

•

Be

careful

not

to

let

the

rubber

become

twisted.

•

Rotate

the

turntable

(platter)

several

times

to

make

sure

that

it

is

secure.

G-~---...-z-:-------

..

------

::~::;:;ng

~

Rubber

belt

I I

I

I I

,,

,,

r

' 0

Preparing

the

record player

!I Place

the

felt

mat

on

the

turntable

(platter).

Place

the

mat

that

is

included

with

the

turntable

on

it

before

use.

11

Install

the

counterweight.

Place

the

counterweight

over

the

end

of

the

tone

arm

and

turn

it

clockwise

to tighten

it

~

Counterweight

i

~

ffl

Install

the

headshell.

Insert

the

headshell

on

the

end

of

the

tone

arm

and

turn

the

nut

to

secure

it

In

place.

Nut~

f

tt

_,hOI

Balancing

the

tone

arm

and

adjusting

the stylus.,,......,.

--

\ -

Stylus

pressure

adjustment

ring

/rlC......,--,,,.

,;;:

\

Center

line

' ·

•·

Anti-skating

dial

Cue

lever

n Set

the

anti-skating dial

to

zero.

fl

Move

the

tone

arm

clasp

to

the

right

to

release

the

tone arm.

IJ

Lift

the

cue lever and shift

the

tone arm

to

the

left

slightly.

!I Lower

the

cue lever.

11

Turn

the

counterweight

and

adjust

so

that

the

tone arm

Is

level.

•

Remove

the

protective

cap

from

the

cartridge

stylus

before

adjusting.

•

Be

careful

not to let

the

cartridge

stylus

touch

the

unit.

ffl

Return

the

tone arm

to

its original posi-

tion, and move

the

tone arm clasp

to

the

left

to

lock

It

In place.

IJ

Turn the stylus pressure adjustment ring

so

that

the

center line aligns

with

O on

the scale.

•

Be

careful

not

to let

the

counterweight

turn.

11)

Turn the counterweight

so

that

the stylus

pressure adjustment ring scale matches

the

stylus pressure

specified

for

the

cartridge.

TN-280BTstandard

models:

•

The

stylus

pressure

of

the

Included

cartridge

is

3.0

g.

For

3.0g

stylus

pressure,

turn the counterweight

counterclockwise

around

one

time completely

so

that

the

stylus

pressure

adjustment

ring

passes

O

and

then

keep

turning it until

0.5

aligns

with

the

center

line.

(Do

not

turn

the

ring

by

itself.)