OPTN400BTTEA04 TEAC r:t □ ~·~-:J7-,·,11 ANALOG TURNTABLE lll&llftBJHI 0 ,'.
IMPORTANT SAFETY INSTRUCTIONS 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
Compliance of radio transmitter and interference Radiation Exposure requirements This equipment meets the regulation, which is recognized This product has the function of broadband transmitter using internationally, for the case of human exposure to radio waves 2.4GHz Band. generated by the transmitter. Use frequency range: 2402 MHz - 2480 MHz Maximum output power: Bluetooth• Class 2 (less than 2.
Thank you for choosing TEAC. Read this manual carefully to get the best performance from this unit. shown below. Please contact the store where you purchased this unit if any of these accessories are missing or have been • • • .14 Preparing the record player . . Dust cover . Notes about record styluses . . .. .. .. . .. . .... . . . . 16 .
Preparing the record player Precautions for use • Do not leave records in places that are exposed to direct sunlight or are very hot or very humid. Leaving a record in such a condition for a long time could result in warping, mold growth or other damage. Keep the unit in standby while setting it up ( I] on page 18). n !J Place the felt mat on the platter. Place the included felt mat on the platter before use. Balancing the tonearm and adjusting the tracking force Place it on a flat surface.
Dust cover Preparing the record player (continued) n Turn the counterweight and adjust so [I Turn the counterweight so that the matches the tracking force specified for the cartridge. • N Attaching the dust cover tracking force adjustment ring scale that the tonearm is level. Dustcover The tracking force of the included cartridge is 2.0 g. Opening and closing the dust cover So, turn it to 2 on the counterweight scale when using the included cartridge.
• If the stylus becomes bent (damaged), it will no longer To change the cartridge, first remove the headshell from the be able to accurately trace the groove. Since a bent stylus tonearm. could also damage records and cause malfunction, handle • Names and functions of parts Changing the cartridge Notes about record styluses • An Audio-Technica AT95E VM Type cartridge is installed in styluses carefully. this unit. Always use a commercially-available stylus cleaner to clean Ell VM a stylus.
Connections [:'J DC input connector After completing all other connections, connect the included AC adapter to this connector. Confirm that the power plug of the AC adapter is ,I, ., ., -- .....- plugged into a power outlet. 1; CJ B When PHONO EQ is ON m Connect to line input connectors of amplifier, etc. • Do not use any AC adapter other than the one included. • changed. Attach the plug that suits the region where it Included AC adapter is being used.
Basic operation !] Playing records n Select the rotation speed indicated on I] Move the tonearm to the track where you want to start playback. the record. The rotation speed can be set to 33 1/3, 45 or 78 RPM. Press the STANDBY/ON button on the When playback finishes n Utt.;;~&,I Raise the tonearm lifter lever to separate the stylus from the record, and back of the unit to turn it on. return the tonearm to its original i position. =ON .Ll.
Listening with Bluetooth ®speakers Pairing might take some time depending on the If you experience a problem with this unit, please check the fol- connected device. lowing items before requesting service. Something other than This unit will connect to the closest Bluetooth this unit could also be the cause of the problem. Please also Press the STANDBY/ON button on the speaker. If no Bluetooth speaker is found for five check that the connected devices are also being used properly.
Specifications Platter Drive system . Motor. .... Belt drive . ............................. DC motor Rotation speed .... 33 1/3 rpm, 45 rpm, 78 rpm Output voltage General PHONO EQ THRU.......... ..... .. . . . . . .3.5 mV (1 kHz, 5 cm/s) AC adapter power PHONO EQ ON. Output connectors. . .. 155 mV (-16 dBV) SN ratio .............. 67 dB or higher (A-weighted, 20 kHz LPF) On (START). Bluetooth function Bluetooth version Output class .......... .. ... . . ... . ......... 4.0 (DUAL MODE) ........
WARRANTY/GARANTIE/GARANTiA/GARANTIE/GARANZIA/GARANTIE/GARANTI Warranty provisions (United States and Canada only) Length of Warranty The parts and labor warranty will be effective for one (1) year from the date of the original purchase for products not used for commercial purposes. For products used commercially, the warranty is ninety (90) days for magnetic heads and optical pickups, one (1) year for all other parts and ninety (90) days for labor.
In countries/regions other than the USA, Canada, Europe and Japan Europe/Europa This product is subject to the legal warranty regulations of the country of purchase. In case of a defect or a problem, please contact the dealer where you bought the product. Ce produit est sujet aux reglementations concernant la garantie legale dans le pays d'achat. En cas de defaut ou de probleme, veuillez contacter le revendeur chez qui vous avez achete le produit.
D □□ i* ~iE;:::O)~fil!Jll,L m *•~c.tl7'i@cffllf'l~1'~fi5.:::c~ ~ :P:t- □ ~-$7-:.t:r-:1Jl, SJ:CT It ~ ft iifilllllrdl •* cl'3f-.l5R9-QtJO)c1t o i!5~...tl10)E3b'51i:~cWJrJJcp1;: Wll!i!m~~t.,,,Ji&lcl:. *li~c~mO)...t. lll(ID~a,EJ ~ li:~ci\i0)5' -f 7'Y?~1'12-Y::l -'iFic.lcl:S~...1:110) ll&?'c!6li:i~1'~2~fli
Gpe Microsystems Instruction Manual G Series Interchangeable AC Plug Models 1. Pull back tab and hold. 2. Mate round corner of plug to round corner of receptacle. 3. Insert plug into adapter receptacle head-first until it sits completely inside, then release tab to lock in place. Head (RoulJd Corner) ~◄ ~ US plug Tail Adapter Receptacle UK plug CAUTION: ELECTRIC SHOCK DO NOT INSERT PLUG ALONE TO ELECTRICAL OUTLET. All plugs may not be included. © Gpe Microsystems Corp.
