Owners Manual
Table Of Contents
- ENGLISH
- IMPORTANT SAFETY INSTRUCTIONS
- Trademarks and copyrights
- Included accessories
- Maintenance
- Using the TEAC International Site
- Before use
- Downloading the remote app
- Connections (back)
- Network connections
- Connections (front)
- Using the remote control
- Remote control parts and functions
- Main unit parts and functions
- Upconversion
- Display
- Basic operation
- Bluetooth® wireless technology
- Settings
- Playing back music on a computer
- MQA (Master Quality Authenticated)
- Troubleshooting
- Specifications
- FRANÇAIS
- INSTRUCTIONS DE SÉCURITÉ IMPORTANTES
- Marques déposées et copyrights
- Accessoires fournis
- Entretien
- Utilisation du site international TEAC
- Avant l’utilisation
- Chargement de l’appli de télécommande
- Branchements (face arrière)
- Connexions réseau
- Branchements (face avant)
- Emploi de la télécommande
- Parties et fonctions de la télécommande
- Parties et fonctions de l’unité principale
- Conversion ascendante
- Affichage
- Fonctionnement de base
- Technologie sans fil Bluetooth®
- Réglages
- Lecture de musique sur un ordinateur
- MQA (Master Quality Authenticated)
- Guide de dépannage
- Caractéristiques techniques
- ESPAÑOL
- INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- Marcas y derechos de propiedad
- Accesorios incluidos
- Mantenimiento
- Web internacional de TEAC
- Antes de su utilización
- Descarga de la app de control remoto
- Conexiones (panel posterior)
- Conexiones de red
- Conexiones (panel frontal)
- Uso del mando a distancia
- Partes y funciones del mando a distancia
- Partes y funciones de la unidad principal
- Sobreconversión
- Pantalla
- Funcionamiento básico
- Tecnología inalámbrica Bluetooth®
- Ajustes de configuración
- Reproducción de música en un ordenador
- MQA (Master Quality Authenticated)
- Solución de problemas
- Especificaciones
- WARRANTY/GARANTIE/GARANTÍA
18
Basic operation
1 Shift the STANDBY/ON switch to its ON position
to turn the unit on.
o If a stereo amplifier is connected to this unit, always turn the
amplifier on very last.
2 Minimize the volume.
Minimize the volume on devices used to control the volume
(this unit, the stereo amplifier or other equipment connected
to this unit).
3 Press the OUTPUT button to select the
connector(s) that output(s) analog audio.
4 Turn the SOURCE knob to select the input
source.
The selected source appears on the display.
o You can also use the input selection buttons on the remote
control.
o If the input signal is not a digital audio signal or is an audio
signal format that is not supported by this unit, such as
Dolby Digital or DTS, no audio will be output. Set the digital
output of the connected device to PCM audio output.
o To play back audio files when this unit is set to USB, you
must first install a dedicated driver on the computer before
connecting them (page26).
o DSD data can only be played back when the input source is
USB or NET (including USB flash drives) or when using DoP
format digital input.
o To use NET or a USB flash drive port (front or back), install
TEAC HR Streamer (free) on a smartphone or tablet, and con-
nect it to the same network as the unit.
5 Operate the playback device.
Refer to the operation manual of that device.
6 Adjust the volume.
When using the line outputs
When LINE OUT LEVEL is set to VARIABLE, turn this unit’s VOLUME
knob to adjust the volume.
When LINE OUT LEVEL is set to any other setting, the volume
cannot be adjusted from this unit. Use the stereo amplifier or
other device connected to this unit to adjust the volume.
When headphones are connected to this unit
Turn this unit’s VOLUME knob to adjust the volume.
o When this unit’s VOLUME knob is enabled, the volume set-
ting will be shown.
NOTE
o The automatic power saving function is set to ON when shipped
new from the factory (page24).
o When DIMMER (display brightness) is set to AUTO OFF, the dis-
play will turn off when not being operated (page24).