AssociatedElectrics.
:: Introduction Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new vehicle. Please take a moment to read through the manual and familiarize yourself with the steps. We are continually changing and improving our designs; therefore, actual parts may appear slightly different than the illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags.
:: Hardware - 1:1 Scale View Button Head (bhcs) Flat Head (fhcs) Ball Bearings 2.5x5mm (31519) 2.5x8mm (31448) 2.5x6mm (31520) 2.
:: Quick Start Guide Battery Charging Steps and Safety: Remove the battery from the vehicle before charging. Place battery on a fire resistant surface. Avoid any contact with water or other liquids. Be sure to select the correct charging mode for the type of battery you are charging. ALWAYS use a compatible charger for charging your batteries. Caution: Never leave the battery unattended while charging. Always disconnect the charger from the power source when finished charging.
12/20 :: Quick Start Guide - (cont.) Radio System Tuning and Controls: RULE: Transmitter on First/Vehicle on Second, Vehicle off First/ Transmitter off Last! 1) 2) 3) 4) Slide the battery cover to remove cover. Install alkaline or rechargeable AA size batteries into the battery holder. Slide the battery cover back into place making sure it is completely closed and secure. Turn the power ON. If the power indicator LED fails to light, check the batteries for insufficient contact or incorrect polarity.
:: Step 1 25810 Sun Gear Shim 25810 Sun Gear Shim 25810 Diff O-Ring 25810 Diff O-Ring 25810 Diff Output Shaft 25810 Diff Output Shaft 25807 Diff Case (Front/Rear) 25810 Sun Gear 25810 Sun Gear 25810 Input Pin 25810 Input Pin 25808 Ring Gear, 37T Build 2 (1 front, 1 rear) :: Step 2 25810 x4 Planetary Gear 25810 x2 Diff Cross Pin 91563 x2 10x15x4mm Bearing 25810 x4 Planetary Gear Shim 31350 x4 2.
:: Step 4 25812 x2 Center Diff Cross Pin 89208 x4 3x14mm FHCS 25812 x4 PLanetary Gear Shim 25812 x4 Center Diff Planetary Gear ff di id flu 25811 Center Diff Gasket Center Diff Fluid: 100k cst #5459 25812 Input Shaft Spline 31448 2.5x8mm FHCS :: Step 5 25831 x2 E-Clip, 2.
:: Step 7 25805 Servo Saver Tube 25825 Spring Cup 25825 Spring Collar 25805 Upper Servo Saver Arm 2.5mm 25805 Lower Servo Saver Arm 25805 Servo Saver Spring Collar 25805 Servo Saver Spring 25832 Shock Spring :: Step 8 25805 Steering Rack 25187 x2 3x14mm BHCS 25819 x2 Steering Block Hat Bushing 31400 x2 5x8x2.5mm Bearing 25805 Bellcrank Arm 41079 x2 2.5x6mm SHCS 25805 x2 2.
:: Step 10 25806 Gearbox Cap 25802 x2 Arm Mount Insert 89202 x2 3x12mm BHCS 25211 x2 3x10mm BHCS 25804 Front Arm 25803 x2 Inner Hinge Pin 25802 Arm Mount 25819 x2 Caster Block Hat Bushing :: Step 11 11 6332 Body Clip 25817 Body Post 25211 x2 3x10mm BHCS 89202 x4 3x12mm BHCS 25816 Front Shock Tower 25817 Body Mount :: Step 12 2 25211 x2 3x10mm BHCS 25818 Caster Block 25821 Pin Screw 25821 Slider Drive Shaft, Male 25819 x2 Hat Bushing 25818 Steering Block
:: Step 13 13 25821 Slider Drive Shaft, Female 25820 2x9.
:: Step 16 25828 x2 Pivot Ball, Long 25189 3x22mm BHCS 25824 x2 Ball Cup 25824 Turnbuckle 89203 3x16mm BHCS Steering Turnbuckle 15.50mm 25215 M3 Locknut Build x2 (right and left side) :: Step 17 25828 x2 Pivot Ball, Long 25824 Turnbuckle 25187 3x14mm BHCS 25824 x2 Ball Cup Steering Turnbuckle 22.00mm 25187 3x14mm BHCS Build x2 (right and left side) :: Step 18 25815 Motor Mount 25815 Motor Mount Nut 31519 2.
:: Step 19 25852 x2 Chassis Guard 25211 x2 3x10mm BHCS 25211 x4 3x10mm BHCS :: Step 20 89207 x2 4x12mm BHCS 25856 Drive Shaft 31520 x2 2.
:: Step 22 25802 Arm Mount 25802 x2 Arm Mount Insert 25211 3x10mm BHCS 25802 x2 Arm Mount Insert 25804 Rear Arm 25802 Arm Mount 89203 x2 3x16mm BHCS 25803 x2 Inner Hinge Pin :: Step 23 25817 x2 Body Post 25816 Rear Shock Tower 25817 Body Mount 25211 x2 3x10mm BHCS 25821 Pin Screw 25187 x2 3x14mm BHCS 6332 x2 Body Clip 25821 Slider Drive Shaft, Male :: Step 24 25821 Slider Drive Shaft, Female 25818 Rear Hub 91563 10x15x4mm Bearing 25710 5x11x4mm Bearing 25820 2x9.
:: Step 25 25835 x2 Anti-Roll Bar Eyelet 25215 M3 Locknut 81258 3x12mm Set Screw 1mm 25803 Outer Hinge Pin :: Step 26 25225 3x3mm Set Screw 25835 Anti-Roll Bar, Rear 25835 Anti-Roll Bar Pivot Ball 91158 x2 3x4mm BHCS :: Step 27 25828 x2 Pivot Ball, Long 25824 Turnbuckle 25189 3x22 BHCS 25824 x2 Ball Cup 2308 3x18mm BHCS Rear Camber Turnbuckle 26.
:: Step 28 89207 x2 4x12mm BHCS 25801 Skid Plate 81262 x2 4x10mm FHCS 31520 x2 2.5x6 BHCS 25203 x2 3x12mm FHCS 89206 x2 4x10mm BHCS :: Step 29 25827 Pivot Ball, Small 25827 Pivot Ball, Small 25188 3x20mm BHCS 25188 3x20mm BHCS 25211 3x10mm BHCS 25211 3x10mm BHCS 2308 3x18mm BHCS 25804 Shock Guard 2308 3x18mm BHCS :: Step 30 25853 x2 Front Light Bucket Cap 25853 Front Bumper Brace 25855 Front LED 89202 x2 3x12mm BHCS 31448 x2 2.
:: Step 31 25854 Rear Lower Bumper 25854 x2 Mud Flap Plate 25854 Rear Bumper Brace 25855 Rear Led Lights 25854 Rear Bumper 31520 x2 2.
:: Step 34 Motor 25815 Motor Mount Plate 25225 3x3mm Set Screw 25861 15T-32P Pinion 31532 x2 3x8mm FHCS :: Step 35 25815 Motor Mount Tension Spring 25188 3x20mm BHCS Set The Gear Mesh: To set the gear mesh, rock the spur gear back and forth without making the pinion gear move. Exessive amounts of spur gear movement (loose gear mesh) will cause premature gear failure. If the spur gear mesh is tight, there will be no movement between the spur and pinion gears.
:: Step 37 25827 x2 Pivot Ball, Short 25824 4x12mm Set Screw 25824 x2 Ball Cup Servo Link Turnbuckle 0.80mm 31532 M3x8mm BHCS 25805 Servo Arm, 25T 89202 x2 M3x12mm BHCS :: Step 38 25225 M3x3mm Set Screw ESC Receiver 6338 Antenna Tube, 12” 6727 Servo Tape Battery :: Step 39 25860 Pro SC10 Wheel 25860 Pro SC10 Tire ! Carefully apply ca glue (tire adhesive) to the tire bead on the side.
:: Step 40 91738 x2 M4 Black Nut Serrated Aluminum Install 4 :: Step 41 31532 x3 3x8mm BHCS 25858 SC10 Body, Painted 91477 x3 Nuts, M3, Black 6332 x4 Body Clip
:: Tuning Tips Tips for Beginners: Before making any changes to the standard setup, make sure you can get around the track without crashing. Changes to your vehicle will not be beneficial if you can’t stay on the track. Your goal is consistent laps. Once you can get around the track consistently, start tuning your vehicle. Make only ONE adjustment at a time, testing it before making another change.
:: Shocks 25825 25826 25827 25831 25832 Rival Rival Pivot Rival Rival MT10 MT10 Balls, MT10 MT10 Shock Shock Short Shock Shock 1 2ea. 10 1 2ea.
:: Front Bumpers 2308 25853 25855 31448 89202 M3x18mm BHCS Pro4 SC10 Front Bumper Pro4 SC10 LED Light Kit M2.5x8mm FHCS M3x12mm BHCS 10 1 1 10 10 89202 89202 31448 25853 25853 25855 25853 31448 25853 2308 2308 89202 :: Rear Bumpers 25211 25187 25854 25855 31520 31532 M3x10mm BHCS M3x14mm BHCS Pro4 SC10 Rear Bumper Pro4 SC10 LED Light Kit M2.
:: Steering Bellcrank 25215 25805 25819 31400 41079 89202 M3 Locknut Rival MT10 Steering Bellcrank Set Rival MT10 Hat Bushing Set 5x8x2.5mm Bearing M2.
:: Front Gearbox 25211 25802 25803 25806 25809 31350 89202 91563 91564 10 1 1 1 1 10 10 4 4 M3x10mm BHCS Rival MT10 Arm Mounts Roval MT10 Hinge Pin Set Rival MT10 Front & Rear Gearboxes Rival MT10 Oudrive Shaft & Pinion Set M2.
:: Front Arm 2308 25187 25211 25215 25710 25803 25804 25818 25819 25820 25821 89203 91563 91738 M3x18mm BHCS M3x14mm BHCS M3x10mm BHCS M3 Locknut 5x11x4mm Bearings Rival MT10 Hinge Pin Set Rival MT10 Suspension Arm Set Rival MT10 Caster & Steering Block Set Rival MT10 Hat Bushing Set Rival MT10 12mm Wheel Hexes Rival MT10 Drive Shaft Set M3x16mm BHCS FT 10x15x4mm Bearings M4 Black Nut, Serrated Aluminum 10 10 10 10 2 1 1 1 1 4 1 10 4 10 25821 91563 25187 25820 25821 25818 25821 25710 91738 25804
:: Front Shock Tower 6332 25188 25189 25211 25215 25816 25817 25827 89202 Body Clips M3x20mm BHCS M3x22mm BHCS M3x10mm BHCS M3 Locknut Rival MT10 Shock Tower Set Rival MT10 Body Mount Set Rival MT10 Pivot Balls, Short M3x12mm BHCS 10 10 10 10 10 1 1 10 10 6332 25817 25817 6332 25817 6332 25816 6332 25215 25827 25188 25215 25211 25827 25211 25188 25189 89202 25189 :: Rear Shock Tower 6332 25187 25188 25189 25211 25215 25816 25817 25827 25825 Body Clips M3x14mm BHCS M3x20mm BHCS M3x22mm B
:: Chassis 6332 6338 25188 25211 25225 25815 25852 25856 25861 31500 31519 31520 31531 31532 31541 71050 89207 91158 10 1 10 10 10 1 1 1 1 10 10 10 10 10 10 2 10 10 Body Clips Antenna Tube, 12” M3x20mm BHCS M3x10mm BHCS M3x3mm Set Screw Rival MT10 Motor Mount Set Pro4 SC10 Chassis, Guards, Cover, Foam Pro4 SC10 Center Drive Shaft 15T-32P Pinion Gear M3x2.5mm Set Screw M2.5x5mm BHCS M2.
:: Reedy Electronics :: Lubes & Adhesives / Decals / Misc. 1105 1596 1597 6588 6591 6636 6727 FT Green Slime Shock Lube FT Locking Adhesive FT Tire Adhesive Black Grease - 4cc S.
:: Apparel / Promotional :: Tools TEE SHIRTS AE 2017 Worlds Tee, Black (S, M, L, XL-5XL) Team Associated Tri T-Shirt, Black, (S, M, L, XL-5XL) Team Associated Womens Tri T-Shirt, Black, (S, M, L) Team Associated Youth Tri T-Shirt, Black, (S, M, L) Reedy W19 T-Shirt, Black, (S, M, L, XL-3XL) Element RC Logo T-Shirt, Gray, (S, M, L, XL-5XL) Element RC Rhombus T-Shirt, Black, (S, M, L, XL-5XL) 1 1 1 1 1 1 1 HOODIES/JACKETS AE 2017 Worlds Pullover, Black, (S, M, L, XL-3XL) Team Associated Tri Zip-Up, Bla
