:: Introduction Thank you for purchasing this Team Associated Qualifier Series product. This manual contains instructions and tips for maintaining your new Pro SC 4x4 RTR. Please take a moment to read through it and familiarize yourself with these steps as they will help you to understand each component’s function and show you some tips for getting the most out of your Pro SC 4x4 RTR.
10/14 :: Table of Contents 1....................Cover 2....................Introduction 3....................Table of Contents 4....................Blueprint of a Pro SC 4x4 5-7................Quick Start Guide 8....................Radio, Speed Control Wiring 9...................Gear Mesh & Ride Height 10.................Camber & Toe Settings / Slipper Adjustment 13-14..........Front Diff Access 14.................Diff Maintenance 14-15..........Shock Maintenance 16.................Motor Manual 17.....
:: Blueprint of a Pro SC 4x4 Front Bumper Front CVA Front Arm Front Shock Turnbuckle (Front Camber Link) Caster Block Steering Block Front Body Mount Front Shock Tower Turnbuckle (Front Steering Link) Turnbuckle (Front Servo Link) Chassis Battery w/ High Power Connector Receiver Box Drive Shaft Nerf Bar Electronic Speed Control Battery Strap Motor Slipper Clutch Pinion Spur Gear Rear Arm Rear Shock Tower Rear Hub Rear Dogbone Rear Bumper Rear Shock Rear Body Mount Turnbuckle (Rea
:: Quick Start Guide Battery Charging Steps and Safety: NiMH Wall Charger: (Part #29154 Wall Charger AC 120V 350MaH) NiMH Quick Charger: (Part #610 Reedy 447-S AC/DC 4-7 Cell Peak Prediction NiMH/NiCd Charger) Remove the battery from the vehicle before charging. Be sure to select the correct charging mode for the type of battery you are charging. NEVER leave the battery unattended while charging! NiMH: NiMH batteries (nickel-metal hydride) are high current rechargeable batteries.
:: Quick Start Guide - (cont.) Throttle Calibration: 1) 2) 3) 4) 5) 6) Set your radio’s throttle and brake EPA/ATV to 100% and your throttle trim to neutral. Then turn on your transmitter. Press and hold the SET button while powering ON the ESC. When the LED begins to flash, release the SET button immediately. With the throttle trigger at neutral, press the SET button to save the neutral position verified by one flash of the LED.
:: Quick Start Guide - (cont.) Radio System Tuning and Controls: 4 RULE: Transmitter on First/Vehicle on Second, Vehicle off First/ Transmitter off Last! 1) 2) 3) 4) Slide the battery cover in the direction shown to remove cover. Install six (6) alkaline or rechargeable AA size batteries into the battery holder. Slide the battery cover back into place making sure it is completely closed and secore. Turn the power ON.
:: Wiring Diagrams Receiver Box Gasket Maintenance: 1. Apply a small amount of “hobby grade” glue to the top edge of the receiver box in order to hold the receiver box gasket in place. Do the same for the receiver box lid. Make sure not to get glue on the side of the gaskets that will make contact with each other! Wait untill the glue has completely dried before moving on to the next step! 2. Once the receiver box gasket is installed, you can then plug your servo and speed control into your receiver.
:: Gear Mesh Gear Mesh: To correctly set your gear mesh, follow the steps below: 1. Remove the Chassis Brace. Loosen the set screw on the motor’s pinion gear. Slide the pinion on the motor shaft until the gear face of the pinion is entirely aligned with the gear face of the spur gear (see diagram). Tighten the set screw while ensuring it is aligned with the flat face on the motor shaft. Pinion Spur Gear 2. Loosen the motor clamp screw until the motor is able to move freely.
:: Camber / Toe Front Camber Angle: A good starting camber setting is –2 degrees (where the top of the tires lean inwards). Positive camber, where the top of the tire is leaning out, is typically not recommended. Front Toe-In: Zero degree toe-in (tires pointing straight forward) is a good starting setting. You can increase steering into corners by adding 1-2 degrees of toe-out (front of tires point slightly outward). Front toe - in is not a typical tuning adjustment used.
:: Spur Gear Access :: Spur Gear Access - (cont.) :: Spur Gear Access - (cont.) Rear Shock Tower Removal: Loosen the hardware highlighted in order to remove the shock tower with the shocks and camber turnbuckles attached as one complete piece. The dogbones will come out when the shock tower is removed.
:: Spur Gear Access - (cont.) Slide center bulkhead cap forward to remove slipper assembly! :: Spur Gear Access - (cont.) NOTE the direction of the gear diff when re-installing into the chassis! :: Spur Gear Access - (cont.) Spur Gear Maintenance: When accessing your spur gear, check for wear on the teeth of the gear. The teeth should be nice and sharp. Also, check the slipper pads for wear. Replace if necessary. A good starting point for slipper setup is to have 3.5 to 4.
:: Front Diff Access :: Front Diff Access - (cont.) :: Front Diff Access - (cont.) Front Shock Tower Removal: Loosen the hardware highlighted in order to remove the shock tower with the shocks and camber turnbuckles attached as one complete piece.
:: Front Diff Access - (cont.) NOTE the direction of the gear diff when re-installing into the chassis! :: Diff Maintenance Differential Maintenance: Once you have removed the Diff gear, you can now drain the existing diff fluid from the differential. Stock Shock Fluid Setting: Check the diff gasket for wear or damage. Replace if necessary Front: black grease Fill the diff to the top of the cross pin with your choice of diff fluids.
:: Shock Maintenance - (cont.) Shock Maintenance: If you need to only refill your shocks with oil, follow the steps above only then move to the shock bleeding steps. If your shocks leak from the bottom shock cap, follow all shock maintenance sections. Replace the inner O-Ring in the bottom cap, then begin the shock oil filling and bleeding process. NOTE: When re-installing the shock spring cup, make sure any outer limiters go above the shock spring cup! :: Shock Maintenance - (cont.
:: Motor Manual 550-SL BRUSHLESS MOTOR Introduction Caution Congratulations on your purchase of the Reedy 550-SL Brushless Motor. The latest brushless motor technology along with the design and engineering experience that is responsible for 29 World Championship titles has been incorporated into its design. When switching to a higher voltage battery from a lower one (11.1V to 7.4V, for example), a change in gear ratio or a lower kV motor might be necessary.
:: ESC Manual
:: Shocks 7231 7232 7233 7234 7235 7236 7237 89066 89067 89352 89353 89354 89394 89396 :: Servo Saver/Mount 4x25mm Shock Shaft (Pro SC) 16mm Shock Spring, White 3.0lbs 16mm Shock Spring, Shiny Black 3.8lbs - Kit Rear 16mm Shock Spring, Black 4.
:: Front and Rear Gear Differential 7133 7134 7732 25607 31350 1 2 6 4 6 Diff - Complete Diff Outdrive w/Set Screw M4x4mm Set Screw Bearing, 8x14x4 M2.5x10mm FHCS 25607 7134 7134 -OR7732 31350 25607 7134 7134 -OR7732 :: Battery Strap :: Lubes & Adhesives / Decals / Misc.
:: Front Gearbox 7163 7166 7732 25202 25211 25215 25231 25710 89202 M3x18mm BHCS Red Silicone O-Ring ProLite Chassis Braces Gearboxes FR/RR, Top & Bottom Front Input Shaft, Set Diff Outdrive, w/ set screw Drive Pinion Arm Mounts, A & D Plates Hinge Pins (inner & outer), Bushings (0, 1, 2, & arm washers) Set Ball Stud, (3 short/7 long) Set 4mm E-Clip M4x4mm Set Screw M3x10mm FHCS M3x10mm BHCS M3 Locknut, black E-Clip, 2.
:: Rear Gearbox 7117 7155 7158 7163 25202 25215 89202 1ea 1ea 1 Gearboxes FR/RR, Top & Bottom Arm Mounts, A & D Plates Hinge Pins (inner & outer), Bushings (0, 1, 2, & arm washers) Set Ball Stud, (3 short/7 long) Set M3x10mm FHCS M3 Locknut, black M3x12mm BHCS 89202 1 20 20 10 7163 89202 7163 7117 BLANK BLANK 7158 7158 7158 7158 7158 7158 25215 7158 7158 7155 7117 7158 7158 25202 :: Rear Suspension 7131 7132 7142 7156 7163 7158 7165 7168 7237 7240 25616 89203 91027 91148 Dogbone (RR) Axle
:: Front Bumper 2308 7119 25201 25204 25211 M3x18mm BHCS Front Bumper, Set M3x8mm FHCS M3x16mm FHCS M3x10mm BHCS 6 1 20 20 20 25211 7119 7119 2308 7119 25204 25201 25201 :: Rear Bumper 2308 7120 7121 25201 25187 89203 89218 M3x18mm BHCS Rear Bumper, Set ProLite Mud Flaps M3x8mm FHCS M3x14mm BHCS M3x16mm BHCS Washer, 3x8mm 6 1 2 20 20 10 10 2308 7120 25201 89203 7120 89218 25201 7120 25187 7121 7120 7120 25201 25187 7121 25201 25201 25201 89218
:: Front Shock Tower 7154 7173 7184 25187 25612 89083 89218 89473 91478 :: Rear Shock Tower Shock Tower, Front & Rear Pro Rally Body Mount Set M2x16mm SHCS M3x14mm BHCS M3 Locknut with Flange, black Shock Bushing Washer, 3x8mm Shock Standoff, steel M3x30mm BHCS 1ea 1 10 20 20 4 10 2 6 7154 7173 7184 25187 25612 89083 89218 89473 91478 Shock Tower, Front & Rear Pro Rally Body Mount Set M2x16mm SHCS M3x14mm BHCS M3 Locknut with Flange, black Shock Bushing Washer, 3x8mm Shock Standoff, steel M3x30mm BH
:: Chassis 2308 7112 7113 7114 7116 25187 25202 25211 25215 31532 89202 89203 M3x18mm BHCS ProLite Chassis Nerf Bars Receiver Box w/Gaskets ProLite Chassis Braces M3x14mm BHCS M3x10mm FHCS M3x10mm BHCS M3 Locknut, black M3x8mm BHCS M3x12mm BHCS M3x16mm BHCS 6 1 2 1 1 20 20 20 20 6 10 10 2308 25211 25187 25211 31532 89203 31532 7114 25187 31532 7116 89202 7114 7116 7116 7114 7113 25215 89202 25215 7112 25202 89202 25215 89202 7113 25202 25215
:: Slipper, Spur Gear, Pinion, and Drive Shaft 5407 7122 7123 7124 7125 7126 7127 7135 7732 25225 25231 25710 91162 91163 91164 91165 91166 Red Silicone O-Ring Spur Gear 32P, 47T Slipper Hardware, Kit Slipper Shaft Slipper Pads Slipper Hubs Drive Shaft w/ O-Rings Drive Pinion M4x4mm Set Screw M3x3mm Set Screw E-Clip, 2.
:: Reedy Accessories :: Body / Decals 1734 1735 1736 1737 6332 7161 7162 7169 7238 7239 9836 9837 9838 9842 9843 9844 9846 9848 9849 9850 9856 9857 9858 9860 9862 9863 9876 9886 9896 9897 FT Body Clips, Metallic Blue, 4 long, 6 short FT Body Clips, Metallic Blue, long FT Body Clips, Metallic Blue, short FT Body Scissors Body Clips ProLite Body, Gray painted ProLite Body, Blue painted ProLite Decal Sheet Pro SC Body, Blue/Yellow Pro SC Body, Blue/White SC10 Body, clear SC10 09’ Championship Body, clear
:: Reedy Motors and ESC’s 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 908 909 920 921 922 923 924 925 954 956 958 965 966 967 983 984 985 986 987 29180 Sonic 540 Mach 2 21.5 Competition Brushless Motor Sonic 540 Mach 2 17.5 Competition Brushless Motor Sonic 540 Mach 2 13.5 Competition Brushless Motor Sonic 540 Mach 2 10.5 Competition Brushless Motor Sonic 540 Mach 2 9.5 Competition Brushless Motor Sonic 540 Mach 2 8.5 Competition Brushless Motor Sonic 540 Mach 2 8.
:: Hardware - 1:1 Scale View Cap Head (shcs) Button Head (bhcs) Flat Head (fhcs) 3x10mm (25620) 2.5x6mm (4675) 2.5x6mm (31520) 2.5x10mm (31350) 3x4mm(91158) 3x8mm (25201) 3x8mm (31532) 3x10mm (25202) 3x10mm (25211) 3x16mm (89224) 3x12mm (89202) M3 Locknut (25215) M3 Alum.
:: Apparel SP20 AE Patch Trucker Hat SP21 AE Patch SP23** AE Splash T-shirt - Black (S, M, L, XL, 2-5XL) SP24** AE Splash T-shirt - Blue (S, M, L, XL, 2-5XL) SP31** 27 Time WC T-shirt - Black (S, M, L, XL, 2XL, 3XL) SP32** AE Kids T-shirt - Blue (S, M, L) SP37** Reedy 2012 T-shirt - Black (S, M, L, XL, 2XL, 3XL) SP38 Reedy Trucker Hat SP39 Reedy Patch SP77** AE 2012 T-Shirt, Blue (S) SP78** AE 2012 T-Shirt, White (S, 3XL) SP79** AE 2012 T-Shirt, Black (S, XL, 2XL) SP84** Reedy 3D T-Shirt, Black (S, M, L,
:: Trouble Shooting Description Problem Solution Receiver LED remains red. Charge battery. Plug in battery. Reset speed control using your instruction manual. Re-bind transmitter to the receiver. No Throttle Motor not plugged in............ Speed control out of ............ adjustment. Motor failure............................ Plug in motor. Reset speed control using your instruction manual. Replace motor. No Steering Servo not plugged in............. Locked up steering linkage. Servo failure....
