ASC90020 B6.1 Buggy Manual

ManualsBrandsTeam Associated ManualsCars & TrucksRC10 B6.1 Team Kit

Summary of content (34 pages)

PAGE 1
PAGE 2
:: Introduction Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new vehicle. Please take a moment to read through the manual and familiarize yourself with the steps. We are continually changing and improving our designs; therefore, actual parts may appear slightly different than the illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags.
PAGE 3
:: Hardware - 1:1 Scale View Button Head (bhcs) Flat Head (fhcs) Ball Bearings 2x4mm (31510) Aluminum (8545) 2.5x6mm (31520) 2.5x8mm (31521) 2.5x10mm (31522) 3x4mm (91158) 3x5mm (31530) 3x6mm (31531) Aluminum (8550) Titanium (91580) 3x10mm (25202) Aluminum (8555) Titanium (91593) 5x10x4mm (91560) 3x12mm (25203) Aluminum (8556) Titanium (91594) 6x13x5 (91562) Set Screws 3x2.5mm (31500) 3x3mm (25225) 3x10mm (4671) Shims and Washers 3x18mm (2308) 5.5x0.
PAGE 4
:: Table of Contents 1................... Cover 13 - 14........Bag 7 2................... Introduction 14 - 15........Bag 8 3...................1:1 Hardware “Fold Out” 15 - 17........ Bag 9 4................... Table of Contents 17 - 19........Bag 10 5....................Bag 1 19 - 21....... Tuning Tips 6 - 8..............Bag 2 22 - 30....... Catalog 8 - 9..............Bag 3 31................ Notes / Contact Info 9 - 10...........Bag 4 32................
PAGE 5
12/17 :: Bag 1 - Step 1 31382 x2 FT Ballstud Washer, Aluminum (1mm) Front ! TOP Note orientation of steering rack. 91667 Steering Bellcrank (Right) 91475 x4 3x7x3 Ball Bearing 91475 x4 3x7x3 Ball Bearing 91667 Steering Rack 31382 x2 FT Ballstud Washer, Aluminum (1mm) 91048 x2 Heavy-duty Ballstud, 8mm 91667 Steering Bellcrank (Left) :: Bag 1 - Step 2 ! The steering bellcrank brace has offsets on one side. They should be installed towards the bearings.
PAGE 6
:: Bag 2 - Step 1 91765 Chassis, B6.1 91656 Bulkhead ! There are two bulkhead settings (25 °, 30 °). 25 ° is the standard used. The arrow should point forward for the desired setting. > 25 30 > 25204 x2 M3 x 16mm FHCS :: Bag 2 - Step 2 91748 FT Steel Chassis Weight, 36g 91734 Battery Foam, B6 91652 Side Rails (L & R) ! #91734 - Battery Foam There are two thickness options to accomodate any battery size.
PAGE 7
:: Bag 2 - Step 4 91719 x2 Servo Mount A - Airtronics F - Futaba H - Hitec J - JR Printed here ! Align the servo horn 90 degrees 91728 x2 Servo Spacers 31532 x4 M3 x 8mm BHCS ! 89218 x4 M3 x 8mm Washer #91728 - Servo Spacers are not required for all servos. :: Bag 2 - Step 5 25187 x2 M3 x 14mm BHCS 25211 x2 M3 x 10mm BHCS 91766 Top Plate, B6 :: Bag 2 - Step 6 25211 x2 M3 x 10mm BHCS ! The front hinge pin brace has a sharp edged side, and a rounded edge side.
PAGE 8
:: Bag 2 - Step 7 91685 Front Bumper 91670 x2 Hinge Pin (front, Inner) 25225 x2 M3 x 3mm Set Screw 25204 x2 M3 x 16mm FHCS :: Bag 2 - Step 8 91771 Front Shock Tower Cover, Gull-Wing 91768 Front Shock Tower, Gull-Wing 25202 x4 M3 x 10mm FHCS 25188 x2 M3 x 20mm BHCS 91815 x2 Shock Bushing, 10mm :: Bag 3 - Step 1 31531 M3 x 6mm BHCS #1596 lock thread 91677 Steering Block (4mm) 91560 x2 5 x 10 x 4 Bearing 4L 91048 Heavy-duty Ballstud, 8mm 91679 Steering Block Arm ! There are two sets of steer
PAGE 9
:: Bag 3 - Step 2 91049 Heavy-duty Ballstud, 10mm 31532 x2 M3 x 8mm BHCS 91675 Caster Block 25215 M3 Locknut, black ! There are three caster block inserts included (0°, +/- 2.5 °, +/- 5 °). +5 ° is the standard insert used. Tab up = positive caster Tab down = negative caster You can install an optional #31520 screw to use as a steering stop setting.
PAGE 10
:: Bag 4 - Step 2 91772 Aluminum Arm Mount, C Out 0.5° 92014 x2 Arm Mount Inserts (0.5°) 92014 x2 Arm Mount Inserts (2.5°, 1°) Corner 1° 31541 x2 M3 x 6mm FHCS 91685 Rear Bumper 91688 Aluminum Arm Mount, D 91670 Hinge Pin (rear, Inner) :: Bag 4 - Step 3 ! The (#91772) C and (#91688) D aluminum arm mounts allow for a large amount of setup combinations when using the (#92014) 0.5° and 1° arm mount inserts.
PAGE 11
:: Bag 5 - Step 2 91783 Gear Diff Crosspin 91780 Gear Diff washer 5x15mm 91780 x4 Planet Gear Diff Shim 3.5 x 9mm #6588 black grease 91783 Gear Diff Cover 91780 x4 Planet Gear #6588 black grease ! 91782 Gear Diff O-Ring #658 8 blac k gr ease 91782 x4 Gear Diff O-Ring 3.3 x 0.6mm 91785 Gear Diff Outdrive #91782 - Gear Diff O-Rings are a tuning option. Kit setup is built without O-Rings :: Bag 5 - Step 3 31522 x4 M2.
PAGE 12
:: Bag 6 - Step 2 ! Do not overtighten #25225 - M3 x 3mm set screw. You could bend the bar! Add a drop of Diff Lube (#6591 - not included) to the teeth of the diff gear, idler gear, and top shaft. 25225 M3 x 3mm Set Screw 1 59 e #6 lub ff di 91823 Anti-Roll Bar, Gray (1.3mm) 91563 x2 10x15x4 Bearing 91821 Anti-Roll Bar Collar 2 91792 x2 B6.1 Diff Height Insert 0 1 ! Diff Height Inserts: The number on top is the setting. Stock diff height is 2.
PAGE 13
:: Bag 6 - Step 5 91801 Slipper Spring Adapter, Inner 25215 M3 Locknut 91801 Slipper Spring Adapter, Inner ! 91801 Slipper Spring ! Set nut flush with top shaft. 25204 x2 M3 x 16mm FHCS See page 20 for gear mesh, and slipper clutch setting instructions! 25202 x6 M3 x 10mm FHCS :: Bag 6 - Step 6 25189 x2 M3 x 22mm BHCS 91769 Rear Shock Tower, B6.
PAGE 14
:: Bag 7 - Step 2 91438 CVA Coupler 91611 M1.6 x 5mm SHCS 91762 HD CVA Axle, V2 91434 CVA Bone, 67mm 91438 CVA Pin 91436 CVA Wheel Hex Pin 91563 10 x 15 x 4 Bearing 8 e 58 eas #6 gr k ac bl 71034 Clamping 91562 Wheel Hex, 6 x 13 x 5 6mm Offset Bearing Do not overtighten the (rear) CVA Axle Holes ! There are two hole locations on the #91762 CVA axle. One is used for the included 67mm CVA bones, and one for the optional 65mm CVA bones. Use the inner hole for the included 67mm CVA bones.
PAGE 15
:: Bag 8 - Step 2 91723 Turnbuckle 3x48mm 91722 Ball Cup 91722 Ball Cup Front Camber Turnbuckle 26.75mm ! Racers Tip: Orient the notch to the left throughout the Use black grease car. It indicates which end (#6588) on the has the left hand threads! threads of the turnbuckles for easier ball cup installation! Build x2 (right and left side) :: Bag 8 - Step 3 ! Orient the notch to the left throughout the car.
PAGE 16
:: Bag 9 - Step 2 91491 12mm Shock Cap O-Ring 91480 12x23mm V2 Shock Bodies (front) 91481 12x27.5mm V2 Shock Bodies (rear) ! ! Lightly rub shock oil on the o-ring before installation! Racers Tip: #11 0 en 5 slim e 91495 V2 Shock Spacer gre 91495 x2 V2 Shock Hat Bushing 5 e 10 #1 slim n e e gr 91820 Shock Eyelet Front Shocks - Short Rear Shocks - Long 31327 VCS3 Shock Bottom Cap O-Ring 91493 x2 X-Ring There is a short and long shock eyelet. Front shocks use the short eyelet.
PAGE 17
:: Bag 9 - Step 5 25612 M3 Locknut w/Flange ! Use center hole in front arm! ! Make sure the flange on the shock pivot ball is towards the rear arm.
PAGE 18
:: Bag 10 - Step 3 89218 x2 3 x 8mm Washer 91731 Battery Strap, B6 91729 x2 Thumb Screw, B6 31531 x2 M3 x 6mm BHCS Front 1 2 3 4 5 91731 x2 Battery Strap Nut, B6 :: Bag 10 - Step 4 25202 x2 M3 x 10mm FHCS Wing Mount 91718 Wing Button x2 0° - Mount under wing 3° - Mount on top of wing 91741 Wing, B6 6° - Mount under wing - KIT 91718 Wing Mount Front of Vehicle Body Trimming / Mounting: There are 3 body trimming options depending on what transmission and shock position you choose to run.
PAGE 19
:: Bag 10 - Step 5 Wheels / Tires and Inserts are not included! 97 #15 ue l g ca ! Carefully apply ca glue (tire adhesive) to the tire bead on the side.
PAGE 20
:: Tuning Tips (cont.) Motor Gearing: Proper motor gearing will result in maximum performance and run time while reducing the chance of overheating and premature motor failure. The gear ratio chart lists recommended starting gear ratios for the most widely used motor types. Gear ratios will vary depending upon motor brand, wind, and electronic speed control. Consult your motor and electronic speed control manufacturers for more information.
PAGE 21
:: Tuning Tips Front Camber Links: Changing the length of the camber link is considered a bigger step than adjusting the ball end height on the tower. Shortening the camber link (or lowering the ball end) will give the front end less roll and quicken steering response. Lengthening the camber link (or raising the ball end) will give the front more roll and slower steering response. Longer camber links are typically used on high grip tracks and shorter links tend to work better on medium-grip loose tracks.
PAGE 22
:: Shocks 4187 31327 31510 89278 91304 91480 91481 91491 91492 91493 91495 91615 91619 91626 91629 91814 91819 91820 :: Optional Ball Differential 12 2 ea. 6 20 2 2 2 1 2 8 1 2 2 4 4 4 ea. 4 1 .030 Nylon Washer VCS3 Shock Bottom Cap and O-Ring 2x4mm BHCS 2.5mm Washer 12MM Threaded Collar and O-Ring 12x23MM V2 Shock Bodies 12x27.5MM V2 Shock Bodies 12MM V2 Shock Rebuild Kit M2 x 4mm BHCS with Washer FT Low Friction X-Rings 12 mm V2 X-Ring Rebuild Kit 3 x 21mm Shock Shaft (V2), TiN 3 x 27.
PAGE 23
:: Transmission 4671 25188 25202 25204 25225 31382 31383 31448 31532 89202 89203 89218 91048 91132 91560 91709 91716 91775 91791 91795 91799 91813 91819 91820 91821 91823 M3 x 10mm Set Screw 10 M3 x 20mm BHCS 10 M3 x 10mm FHCS 10 M3 x 16mm FHCS 10 M3 x 3mm Set Screw 10 Ballstud Washers, 5.5x1.0 mm, 10 blue aluminum Ballstud Washers, 5.5x2.0 mm, 10 blue aluminum M2.
PAGE 24
:: Gear Differential 31522 91563 91780 91782 91783 91784 91785 91786 91792 5450 5451 5452 5444 5453 5446 5454 5455 5466 5456 5457 5458 5448 5459 5461 5463 5465 M2.5 x 10mm BHCS FT Bearings, 10x15x4 mm B6.1 Gear Differential Rebuild B6.1 Gear Differential Seals B6.1 Gear Differential Case B6.1 Aluminum Cross Pins B6.1 Gear Differential Outdrives B6.1 Gear Differential B6.
PAGE 25
:: Front Arm 25187 25188 25215 31510 31531 31532 91048 91049 91560 91670 91673 91676 91679 91682 91776 91826 M3 x 14mm BHCS M3 x 20mm BHCS M3 Locknut, Black M2 x 4mm BHCS M3 x 6mm, BHCS M3 x 8mm, BHCS Heavy-duty Ballstud, 8mm Heavy-duty Ballstud, 10mm FT Bearing, 5 x 10 x 4 Hinge Pin Set, B6 Front Arm, Gull-Wing, B6 B6 Caster Hat Bushings B6 Steering Block Arms Front Axle, B6 B6.1 Caster/Steering Blocks M4 Serrated Wheel Nut, Steel 10 10 10 6 6 6 8 8 4 1 2 2 ea.
PAGE 26
:: Front Shock Tower 25188 25202 25612 91768 91771 91815 M3 x 20mm BHCS M3 x 10mm FHCS M3 Locknuts w/Flange B6.1 Front Shock Tower B6.1 Shock Tower Covers Shock Bushing, 10mm 10 10 10 1 1 4 91771 91768 91815 25188 25612 25188 91815 25612 25202 25202 :: Rear Shock Tower 25189 25202 25612 89202 89218 91718 91769 91816 M3 x 22mm BHCS M3 x 10mm FHCS M3 Locknuts w/Flange M3 x 12mm BHCS M3 x 8mm Washers Wing / Body Mount Set, B6 B6.
PAGE 27
:: Front Bulkhead / Steering 25187 25204 25211 25225 31283 31382 10 10 10 10 6 10 M3 x 14mm BHCS M3 x 16mm FHCS M3 x 10mm BHCS M3 x 3mm Set Screw Ball Studs, Long, 5mm Ballstud Washers, 5.5x1.0 mm, blue aluminum M3 x 2.5mm Set Screw M2.5 x 6mm BHCS M3 x 12mm BHCS Heavy-duty Ballstud, 8mm Heavy-duty Ballstud, 10mm 3x7x3 Ball Bearing Bulkhead, B6 Steering Assembly, B6 M3 x 20mm BHCS, Shouldered Bumpers, B6 B6.1 Top Plate, Ballstud Mount B6.1 Anti-Roll Bar Hardware B6.
PAGE 28
:: Bodies :: Factory Team and Option Parts 91494 91495 91553 91580 91581 91582 91583 91584 91585 91588 91589 91592 91593 91594 91595 91596 91597 91609 91658 91659 91663 91668 91669 91672 91673 91674 91680 91683 91696 91699 91707 91711 91714 91745 91746 91747 91748 91749 91750 91751 91752 91753 91754 91755 91760 91773 91784 91786 91800 91821 91822 91823 FT 12mm Machined Shock Spacers, V2 12mm V2 X-Ring Rebuild Kit Factory Team Bearing Kit, B5, B5M Titanium Screws, 3x6mm BHCS Titanium Screws, 3x8mm BHCS
PAGE 29
:: Reedy Motors / Spare Parts / Accessories MOTORS :: Reedy ESC’s 256 257 258 259 260 261 262 263 264 265 266 284 285 293 294 27401 27402 27403 27404 Sonic 540-M3 10.5 Sonic 540-M3 9.5 Sonic 540-M3 8.5 Sonic 540-M3 8.0 Sonic 540-M3 7.5 Sonic 540-M3 7.0 Sonic 540-M3 6.5 Sonic 540-M3 6.0 Sonic 540-M3 5.5 Sonic 540-M3 5.0 Sonic 540-M3 4.5 Sonic 540-M3 4.0 Sonic 540-M3 3.5 Sonic 540 FT 17.5 Fixed Timing Sonic 540 FT 13.5 Fixed Timing S-Plus 21.5 Spec S-Plus 17.5 Spec S-Plus 13.5 Spec S-Plus 10.
PAGE 30
:: Apparel / Promotional :: Tools SP11* SP12* SP113* SP114* SP120* SP121* SP122* SP123* SP124* SP140* TEE SHIRTS 2016 Worlds T-shirt, blue, (S, M, L, XL-5XL) 2016 Worlds T-shirt, black, (S, M, L, XL-5XL) AE Worlds Car Retro T-Shirt, (S, M, L, XL-3XL) Circuit T-Shirt - Black (S, M, L, XL-3XL) AE 3/4 Sleeve Tee, Gray (S, M, L, XL-3XL) Kids AE Speed Tee, Black (S, M, L) Ladies AE Speed Tee, Black (S, M, L, XL Mens AE Speed Tee, Navy (S, M, L, XL-5XL) AE 2017 Worlds Tee, Black (S, M, L, XL-3XL) Reedy Heri
PAGE 31
:: Notes :: Contact Information Check out the following web sites for all of our electric kits, current products, new releases, setup help, tips, and racing info! Associated Electrics, Inc. 26021 Commercentre Drive Lake Forest, CA 92630-8853 USA http://www.TeamAssociated.com http://www.RC10.com http://twitter/Team_Associated http://www.instagram.com/teamassociatedrc/ http://www.facebook.
PAGE 32
Team Kit Stock Setup Driver: Date: Track: Qualify: Front Suspension: Ride Height: 19mm Camber: -1° Toe: 0° Arm Type: Gull-Wing Tower Type: Gull-Wing Caster Block Insert: +5° 4mm Bulkhead Type: Plastic Kick-Up Angle: 25° Wheel Hex: 5.0mm Steering Block: Event: TQ: Anti Roll Bar: Main: Finish: 0mm Bump Steer Spacing: None White (0.8mm) Gray (0.9mm) Blue (1.
PAGE 33
Driver: Event: Date: Track: Qualify: TQ: Main: Finish: Best Lap Time: Front Suspension: Anti Roll Bar: Ride Height: Camber: Toe: Arm Type: Tower Type: Caster Block Insert: Axle Height: Bump Steer Spacing: None White (0.8mm) Gray (0.9mm) Blue (1.
PAGE 34
Associated Electrics, Inc. 26021 Commercentre Dr. Lake Forest, CA 92630 USA http://www.RC10.com https://twitter.com/Team_Associated https://www.instagram.com/teamassociatedrc/ https://www.facebook.com/TeamAssociated/ call: (949) 544-7500 - fax: (949) 544-7501 Check out the following web sites for all of our kits, current products, new releases, setup help, tips, and racing info! www.TeamAssociated.com. - www.RC10.