Manual

ManualsBrandsTeam Associated ManualsCarsRC10

Summary of content (30 pages)

PAGE 1
PAGE 2
:: Introduction Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new RC10 Worlds Car Kit. Please take a moment to read through this manual to help familiarize yourself with these steps. We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags.
PAGE 3
:: Hardware - 1:1 Scale View Cap Head (shcs) Button Head (bhcs) Flat Head (fhcs) 4-40x1/4 (6285) 4-40x3/8 (6292) 0-80x3/16 (6613) 4-40x5/16” (6932) (4145, aluminum) 4-40x1/2 (6922) 2-56x1/8 (9645) 4-40x3/8 (6924) w/hole (6929) 4-40x3/16 (6920) Flat Head (fhps) 4-40x1/4 (6288) 4-40x1/2 (6925) w/hole (6916) 8-32x1/4 (6931) 4-40x5/8 (6926) 8-32x1/2 (6280) 4-40x3/4 (6927) 4-40x3/8 (6917) 3x6mm (31531) 8-32x7/8 (6281) 4-40x1 (6928) Bushings / Bearings 4-40x1/8 (6951) Oilite Bushing Set (6
PAGE 4
:: Table of Contents 1................... Cover 2................... Introduction 3................... 1:1 Hardware “Fold Out” 11 - 12........ Turnbuckles Build (Bag F) 12 - 14........ Shocks Build (Bag G-GG) 4................... Table of Contents 14 - 15 .......Chassis Build (Bag H-HH) 5....................Nose Plate / Steering Build (Bag A-AA) 15 - 16........ Servo Build (Bag I) 6................... Front Suspension Build (Bag B) 16 - 17........
PAGE 5
2/14 :: Nose Plate / Steering Build - Bag A-AA - Step 1 6331 RC10 Body Mounts (white) 3323 x2 #8 Aluminum Washer (thick) ! 6309 RC10WC Front Nose Plate, (black) You can use 2 or 3 #3323 #8 washers based on body height preference. 6302 RC10WC Chassis, (black) 6280 8-32 x 1/2 Aluminum FHPS 6 #159 k d loc threa 6931 8-32 x 1/4 FHPS 6271 x5 Ballstud .
PAGE 6
:: Front Suspension Build - Bag B - Step 1 7260 4-40 Plain Nut LEFT 6273 Ballstud .30 (silver) 6273 Ballstud .30 (silver) 6936 x2 #4 Washer, Aluminum 7222 Wide Front Axle 6225 RC10WC Inline Steering Blocks Build left and right sides! 6210 RC10 front caster blocks, 30 degrees (Left & Right) 7260 4-40 Plain Nut th #1 re 59 ad 6 lo ck LEFT ! Press stub axles into steering blocks.
PAGE 7
:: Transmission Build - Bag C-CC - Step 1 #65 91 dif f lu be 6579 Diff Drive Ring 6581 x12 3/32 carbide diff balls ! #65 91 dif f lu be The diff gear has four molded dimples on one side. The diff balls should be installed on the opposite side of the dimples.
PAGE 8
:: Transmission Build - Bag C-CC - Step 4 3977 x2 Bearing, 3/16 x 3/8” 3977 x2 Bearing, 3/16 x 3/8” 6569 RC10WC Idler Gear 9361 Idler Gear Shaft 6564 RC10WC Transmission Case (L & R sides) 3976 x2 Bearing, 3/8 x 5/8” :: Transmission Build - Bag C-CC - Step 5 6603 RC10 Motor Plate, black 9601 Top Shaft #6591 be diff lu 6928 x4 4-40 x 1” SHCS #159 threa 6 d loc ! k Note: The head of the diff bolt should be on the same side as the spur gear! :: Transmission Build - Bag C-CC - Step 6 7485 x2 V2 Slip
PAGE 9
:: Rear Bulkhead Build - Bag D-DD - Step 1 6924 x2 4-40 x 3/8 SHCS 6295 x2 4-40 Nuts 6936 x2 #4 Aluminum Washer 6271 x2 Ballstud .20 (silver) #159 threa 6 d loc k 6927 x2 4-40 x 3/4 SHCS 6377 RC10WC Rear Shock Tower ! Cut the bulkhead for a more authentic look to the original Worlds car.
PAGE 10
:: Rear Suspension Build - Bag E - Step 1 6360 RC10 Rear Arm Mounts ! 6380 RC10 Rear Inner Hinge Pins 6355B RC10WC Rear Arms, (black) 6299 x2 E-clip (small) Build left and right sides! Forward holes 6280 x2 8-32 x 1/2 FHPS ! Build left and right sides! :: Rear Suspension Build - Bag E - Step 2 9760 CVA Bone 9755 CVA Axle ! Note: Remove pin retainer to prevent binding if using 4-40 set screw in CVA.
PAGE 11
:: Rear Suspension Build - Bag E - Step 4 6381 RC10 Rear Outer Hinge Pins 6299 x2 E-clip (small) :: Turnbuckles Build - Bag F - Step 1 Note: The servo turnbuckle will be set aside and built when the servo is built and installed into the chassis on page 15. 6279 x2 White Ball Cups 6260 Turnbuckle, 1.00” ! Orient the notch to the left throughout the car. It indicates which end has the left hand threads! Steering Rack Turnbuckle 0.45” (11.
PAGE 12
:: Turnbuckles Build - Bag F - Step 2 6262 Turnbuckle, 1.65” 6279 x2 Ball cups (white) ! Front Camber Turnbuckle 0.86” (22mm) Orient the notch to the left throughout the car. It indicates which end has the left hand threads! Build left and right sides! :: Turnbuckles Build - Bag F - Step 3 6263 Turnbuckle, 2.06” 6279 x2 Ball cups (white) ! Steering Turnbuckle 1.45” (37mm) Orient the notch to the left throughout the car.
PAGE 13
:: Shocks Build - Bag G-GG - Step 2 7438 V2 .71 Threaded Body (front) 6469 Shock cap o-ring 4187 Nylon Spacers Front: 0 Rear: 3 5407 x2 Red O-ring 7481 V2 1.32 Threaded Body (rear) 7484 Shock Bottom Cap 7484 Shock Internal Spacer 5407 Red O-ring (use for rear shocks only) 6468 Shock Pivot Ball 6471 Shock Rod End Build x2 front and x2 rear shocks :: Shocks Build - Bag G-GG - Step 3 id k flu Shoc #5429 t 35w Step 6-7 9645 2-56 x 1/8” BHCS * Shock Bleeding Steps: Step 8 1.
PAGE 14
:: Shocks Build - Bag G-GG - Step 5 6473 Shock Bushing 6472 Plastic Nut 6927 4-40 X 3/4” SHCS Install two front shocks! :: Shocks Build - Bag G-GG - Step 6 6473 Shock Bushing ! 6472 Plastic Nut 6927 4-40 X 3/4” SHCS Note: Use the two washers (#6936) when running the long wheelbase. Remove both washers when running the short wheelbase.
PAGE 15
:: Chassis Build - Bag H-HH - Step 2 6925 x2 4-40 x 1/2” SHCS 6333 RC10 Battery Cup 6339 RC10WC Battery Strap Battery not included! 6292 x2 4-40 x 3/8” FHCS :: Chassis Build - Bag H-HH - Step 3 ! Note: You can sand the end of the battery strap to better fit between the battery pack and the rear bulkhead. Rear of Battery Strap :: Servo Build - Bag I - Step 1 6337 x2 RC10 Servo Mounts 6936 x4 #4 Aluminum Washer Note: The servo turnbuckle and ball cups are left over from bag F. 6271 Ballstud .
PAGE 16
:: Servo Build - Bag I - Step 2 Receiver not included! ESC not included! 6727 x2 Servo tape 6922 x2 4-40 x 1/2” FHCS :: Wheels / Tires and Body - Bag J - Step 1 Motor not included! 6566 RC10WC Gear Cover and Plug ! See page 18 to set gear mesh properly! 31531 x2 3 x 6mm BHCS Pinion not included! 6285 x2 4-40 x 1/4” SHCS :: Wheels / Tires and Body - Bag J - Step 2 97 #15 ue gl a c 97 #15 ue l g ca Tires and Inserts not included! Tires and Inserts not included! ! Build 2 9688 Front Wheel 2.
PAGE 17
:: Wheels / Tires and Body - Bag J - Step 3 3977 x2 Bearing, 3/16” X 3/8” 6952 8-32 Steel Locknut 6222 4-40/5-40 Nylon Locknut, black Build left and right sides! Build left and right sides! :: Wheels / Tires and Body - Bag J - Step 4 Painting Tips: 6332 x2 Body clip Body and Wing: Your RC10 Worlds Kit comes with a clear polycarbonate body and wing. You will need to prep the body and wing before you can paint them. Wash the inside thoroughly with warm water and liquid detergent.
PAGE 18
:: Tuning Tips Tips for Beginners: Before making any changes to the standard setup, make sure you can get around the track without crashing. Changes to your vehicle will not be beneficial if you can’t stay on the track. Your goal is consistent laps. Once you can get around the track consistently, start tuning your vehicle. Make only ONE adjustment at a time, testing it before making another change.
PAGE 19
:: Tuning Tips (cont.) Front Camber Links: Changing the length of the camber link is considered a bigger step than adjusting the ball end height on the tower. Shortening the camber link will give the front end less roll and quicken steering response. Lengthening the camber link (or raising the ball end) will give the front more roll and slower steering response. Front Camber: ! Camber describes the angle at which the tire and wheel rides when looked at from the front.
PAGE 20
:: Shocks 3959 4187 5407 6299 6428 6459 6460 6465 6468 6469 6471 6475 7416 7438 7481 7484 9645 9724 Threaded Shock Collar O-Ring Nylon Spacer, 1/32” (.030) Red O-Rings 1/8” E-Clips Shock End Cap, molded composite Shock Shaft, 1.02” stroke Shock Shaft, .71” stroke Shock Piston, (1, 2, 3) RC10 Shock Rod Ends / Pivots Black O-Ring Rod End, .230 ball, for 2 shocks Shock Cups (4) FT Off Road Threaded Shock Collar with O-Rings, black FT V2 .71 Threaded Bodies FT V2 1.
PAGE 21
:: Turnbuckles / Servo 6260 6262 6263 6264 6271 6279 6337 6922 6924 6936 9180 89007 Turnbuckle, 1.00” 2 Turnbuckle, 1.65” 2 Turnbuckle, 2.06” 2 Turnbuckle, 1.
PAGE 22
:: Front Arm 3977 6206 6208 6210 6222 6223 6225 6226 6227 6273 6280 6299 6927 6936 6951 7222 7260 Bearing, 3/16” X 3/8” Front Suspension Arm, wide, black RC10 Front Arm Mounts RC10 Front Caster Blocks, 30 deg 4-40/5-40 Nylon Locknut, black RC10 King Pin w/Clips RC10WC Inline Steering Block RC10 Front Inner Hinge Pin Hinge Pin, outer, 1.020”, w/ clips Long Ballstud, .
PAGE 23
:: Front Shock Tower 6232 6271 6295 6472 6473 6925 6927 6936 7260 RC10WC Front Shock Tower Short Ballstud, Stainless Steel, .20 4-40 Nuts Plastic Nut Shock Bushing 4-40 x 1/2” SHCS 4-40 x 3/4” SHCS #4 Washer, Aluminum 4-40 Small Pattern Plain Nut 1 12 6ea.
PAGE 24
:: Rear Bulkhead 4436 6189 6271 6280 6323 6327 6331 6332 6593 6932 Set Screw, 4-40 x 5/16” 4 RC10WC Wing Mounts (White) and wire 2 Short Ballstud, Stainless Steel, .
PAGE 25
:: Chassis 3323 6280 6288 6302 6309 6321 6331 6332 6917 6926 6931 #8 Aluminum Thick Washer 8-32 x 1/2” Aluminum FHPS 4-40 X 1/4” BHCS RC10WC Chassis, Black RC10WC Front Nose Plate, Black RC10WC Nose Brace Tubes, Black RC10 Body Mounts (White) Body Clips 4-40 X 3/8” BHCS 4-40 X 5/8” SHCS 8-32 x 1/4” Aluminum FHPS 12 12 6 1 1 2 2 6 6 6 6 6331 6926 6288 6926 6332 3323 6302 6321 6288 6321 6917 6917 6309 6931 6280 :: XP Electronics :: Lubes & Adhesives / Decals / Misc.
PAGE 26
:: Reedy Motors and ESC’s :: Factory Team and Option Parts 897 1401 1402 1403 1405 1409 1736 1779 4449 6210 6220 6221 6222 6241 6242 6259 6260 6261 6262 6263 6264 6270 6271 6272 6273 6274 6325 6366 6390 6416 6418 6431 6435 6443 6463 6465 6473 6565 6619 6910 6937 6943 8253 8254 8255 8256 8257 8258 8259 8260 8261 8263 8264 8265 8266 8267 8268 8269 8270 8271 8272 9310 Bearing, 1/4 X 3/8, flanged FT Titanium Turnbuckle, 1.30”, blue FT Blue Titanium Turnbuckle, 1.375” FT Titanium Turnbuckle, 1.
PAGE 27
:: Qualifier Series Vehicles :: Reedy Batteries 302 309 313 602 637 681 682 683 684 693 694 695 700 730 731 732 734 736 738 739 AA Alkaline 1.5V (4) LiPo 65C 7000mAh 7.4V LiPo 65C 7000mAh 7.4V 5mm LiPo 65C 4100mAh 7.4V Shorty LiPo TX Battery - M11X 2500mAh 7.4V Wolfpack 2400mAh 7.2V w/DEANS® connector Wolfpack 3000mAh 7.2V w/DEANS® connector Wolfpack 3600mAh 7.2V w/DEANS® connector Wolfpack 4200mAh 7.2V w/DEANS® connector Wolfpack 2400mAh 7.2V w/TAM connector Wolfpack 3000mAh 7.
PAGE 28
:: 1/8 Kits and RTR’s 20501 MGT 4.60 SE RTR (ready-to-run) 20502 MGT 8.0 Nitro RTR (ready-to-run) 20503 Limited Edition MGT 4.60 Nitro RTR, w/flag body (ready-to-run) 20504 Limited Edition MGT 8.0 Nitro RTR, w/flag body (ready-to-run) 80906 RC8.2 Nitro Buggy Factory Team Kit 80907 RC8.2e Electric Buggy Factory Team Kit 80908 RC8.2e Electric Buggy RTR (ready-to-run) 80909 RC8.2RS Nitro Buggy RTR (ready-to-run) 80912 RC8T Championship Edition 80933 SC8.
PAGE 29
Driver: Track: Conditions: Date: Event: Outdoor Temp. Indoor Ride Height / Wheelbase Rev.1 Rear Suspension Front Ride Height: Camber: Rear Ride Height: 1 234 Rear Hub Carriers: 0° 1.
PAGE 30
Associated Electrics, Inc. 26021 Commercentre Dr. Lake Forest, CA 92630 USA http://www.TeamAssociated.com http://www.RC10.com http://twitter/Team_Associated http://bit.ly/AEonFacebook call: (949) 544-7500 - fax: (949) 544-7501 Check out the following web sites for all of our kits, current products, new releases, setup help, tips, and racing info! www.TeamAssociated.com. - www.RC10.