0/11
:: Introduction Thank you for purchasing this Team Associated product. This manual contains instructions and tips for building and maintaining your new RC8.2 Factory Team, 1/8 scale racing buggy. Please take a moment to read through it an familiarize yourself with these steps as they will help you to understand each component’s function and show you some tips for getting the most out of your RC8.2 Factory Team build experience.
:: Table of Contents 1....................Cover 2....................Introduction 3....................Table of Contents BAG A 4....................Chassis Assembly BAG B 4-5................Steering Assembly Bag C 6-9................Front, Rear, and Center Differential Assembly Bag D 9-11.............Front Bulkhead Assembly Bag E 11-14..........Front Suspension Assembly Bag F 15-16..........Rear Bulkhead Assembly Bag G 16-19..........Rear Suspension Assembly Bag H 20-21..........
:: Chassis Assembly - Bag A 89552 x2 RC8.2 side guards 89476 FT RC8B +3mm chassis 25201 x4 3x8mm fhcs :: Chassis Assembly (cont.
:: Steering Assembly (cont.)- Bag B 89242 Steering drag link 89526 50mm steel turnbuckle 89074 x2 Steering eyelet 25215 x2 M3 locknut 89077 x2 Flanged pivot ball Smooth edge towards drivers side! ! 89075 x2 RC8 steering ballstuds Build Two 29mm 89455 x2 3x22mm fhcs :: Steering Assembly (cont.)- Bag B 89011 Front body mount ! 89234 Aluminum top plate (blue) 25202 3x10mm fhcs note the direction of the body post during installation.
:: Front/Rear Differential Assembly - Bag C 89115 Diff housing Center Diff Outdrive Diff outdrive differences Front Diff Outdrive (long) 25236 8x16mm bearing bl Rear Diff Outdrive (short) # ac 65 8 k gr 8 ea se ! 89121 Diff O-Ring 89477 Light outdrives (front, long) :: Front/Rear Differential Assembly (cont.
:: Front/Rear Differential Assembly (cont.) - Bag C 89478 Light outdrives (rear, short) 89121 Diff O-Ring 89120 x2 Diff washer #6588 black grease 89477 Light outdrives (front, long) 89121 Diff O-Ring 8 e 58 as #6 gre k ac bl 25236 8x16mm bearing 89494 Light diff ring gear :: Front/Rear Differential Assembly (cont.) - Bag C 89120 Sun gear 89120 Diff outdrive pin ! Align pin with groove in sun gear :: Front/Rear Differential Assembly (cont.
:: Center Differential Assembly - Bag C 89115 Diff housing 89120 x2 Diff washer 89121 Diff O-Ring bl # ac 65 8 k gr 8 ea se 89121 Diff O-Ring 25236 8x16mm bearing #6588 black grease 89119 Diff outdrives (center) :: Center Differential Assembly (cont.) - Bag C 89120 Sun gear 89120 Diff outdrive pin 89120 Spider gear assembly ! Align pin with groove in sun gear :: Center Differential Assembly (cont.
:: Center Differential Assembly (cont.) - Bag C 89120 x2 Diff washer 89121 Diff O-Ring 89120 Sun gear 89120 Diff outdrive pin ! Align pin with groove in sun gear :: Center Differential Assembly (cont.) - Bag C 89208 x4 3x14mm fhcs ! 89116 Diff gasket Tighten screws evenly and firmly. #6588 black grease Diff fluid 5,000cst ! Fill with diff fluid to top of gears.
:: Front Bulkhead Assembly (cont.) - Bag D 89114 Diff pinion gear 89017 Inner gearbox ! 25236 x2 8x16mm bearing ! Wrap boot over the O-Ring. :: Front Bulkhead Assembly (cont.) - Bag D ! Key setscrew onto flat side of shaft. Tighten with no endplay. 96 #15 lock ad e r th 89221 5x4mm setscrew 89481 Low B-Plate 89474 x2 3x22mm shcs :: Front Bulkhead Assembly (cont.) - Bag D 89538 RC8.
:: Front Bulkhead Assembly (cont.) - Bag D #159 6 threa d lock 89473 x2 Steel shock standoffs 3 96 #15 lock ad e r th 2 1 89225 x2 3x24mm shcs 89230 x2 Silver cone washer :: Front Suspension Assembly - Bag E 89105 CVA u-joint coupler 89105 CVA pin #6 5 ck 88 gr ea s 89285 Front stub axle (aluminum) bla e 89102 CVA bone #6588 black gre ase ! ! Axle has additional holes for crosspin to extend the life of the Axle. ! Build Two! :: Front Suspension Assembly (cont.
:: Front Suspension Assembly (cont.) - Bag E 89029 Steering block bushing (short) #1596 thread lock Note: One drop only. Spread evenly inside the threads. ! ! 89206 4x10mm bhcs 89558 RC8.2 caster blocks 89029 Steering block bushing (long) Build right and left sides! Note: Key bushings into steering block. #1596 thread lock ! #1596 thread lock 89207 4x12mm bhcs Do not tighten until bushing is keyed into steering block. ! :: Front Suspension Assembly (cont.) - Bag E 89536 RC8.
:: Front Suspension Assembly (cont.) - Bag E 89269 38mm steel turnbuckle 89549 RC8.2 front upper arm 89076 Camber rod ends Smooth edge towards drivers side! 89230 x2 Silver cone washer ! 25215 M3 locknut Build right 89225 and left 3x24mm shcs sides! 8mm :: Front Suspension Assembly (cont.) - Bag E hinge pin bushing 2 dot up 89553 x2 RC8.
:: Front Suspension Assembly (cont.) - Bag E 89227 3x28mm shcs 89018 Gearbox gasket e 88 as 65 gre # k ac bl 89022 Front bumper 89217 x2 4x14mm fhcs 89214 x2 4x12mm fhcs :: Front Suspension Assembly (cont.
:: Rear Bulkhead Assembly - Bag F 89106 CVA pin 89560 Center CVA bone +3mm (rear) 89286 Gearbox input cup (aluminum) #6588 black grease 89106 CVA u-joint coupler 89557 Pin retainer O-ring ! ! 89557 Pin retainer boot Input cup has additional holes for crosspin to extend the life of the input cup. :: Rear Bulkhead Assembly (cont.) - Bag F 89114 Diff pinion gear 89017 Inner gearbox ! 25236 x2 8x16mm bearing ! Wrap boot over the O-Ring. ! Key setscrew onto flat side of shaft.
:: Rear Bulkhead Assembly (cont.) - Bag F 89011 Body mount (rear) 25215 x2 M3 locknut ! 25620 x2 3x10mm shcs 89454 x2 3x12mm shcs 89224 x2 3x16mm shcs 89117 x2 Diff shim 89017 Outer gearbox 89539 RC8.2 rear shock tower (aluminum) ! Diff shims installed to gear diff, gear diff installed to gearbox. ! :: Rear Bulkhead Assembly (cont.
:: Rear Suspension Assembly (cont.) - Bag G 89105 CVA pin (fr/rr) 89284 Rear stub axle (aluminum) ! ! ! Axle has additional holes for crosspin to extend the life of the Axle. Build Two! :: Rear Suspension Assembly (cont.) - Bag G 89162 15x21mm bearing 89033 hub carrier ! 89107 Bearing shield 25236 8x16mm bearing Build right and left sides! :: Rear Suspension Assembly (cont.) - Bag G th #15 re ad 96 lo ck 89536 RC8.
:: Rear Suspension Assembly (cont.) - Bag G 89454 x2 3x12mm shcs ! 25192 3x20mm shcs ! Droop screw placement! ! ! Build right and left sides! 89551 RC8.2 rear arm 89317 Droop screw 89561 Rear mud guard :: Rear Suspension Assembly (cont.) - Bag G 89076 x2 Camber ball joints 89076 x2 Camber rod end 89076 x2 Camber pivot balls 89269 38mm steel turnbuckle Smooth edge towards drivers side! 6mm Passenger Side Driver Side ! Build right and left sides! :: Rear Suspension Assembly (cont.
:: Rear Suspension Assembly (cont.) - Bag G hinge pin bushing hinge pin bushing 89039 x2 Hinge pin bushings 1 dot 2 dot down 89463 Aluminum D-plate 89470 x2 Hinge pin bushings (two dot) 89452 x2 3x50mm shcs 89466 x2 Inner hinge pin (4mm HMA) ::: Rear Suspension Assembly (cont.) - Bag G 25215 x2 M3 locknut 3 2 1 89230 x2 Silver cone washer 6 5 4 25192 x2 3x20mm shcs ::: Rear Suspension Assembly (cont.) - Bag G #1596 thread lock 89487 RC8B rear swaybar (2.
:: Wing Assembly - Bag H 89229 x2 Blue countersunk washer 25204 x2 3x16mm fhcs 89304 JC Illuzion wing 89540 RC8.2 Wing mount upper brace 25192 x2 3x20mm shcs 25215 x2 M3 locknut 89540 x2 RC8.2 wing mounts 25215 x2 M3 locknut :: Wing Assembly (cont.) - Bag H ! Tighten screws to remove free play but ensure some movement.
:: Rear Clip Install - Bag H 25215 M3 locknut #658 8 black greas e 89018 Gearbox gasket 89217 x2 4x14mm fhcs 89214 x2 4x12mm fhcs 89209 3x18mm fhcs :: Center Bulkhead Assembly - Bag I 89019 Center bulkhead (top) 89122 x2 Brake pads brake pad gap: 4.
:: Center Bulkhead Assembly (cont.) - Bag I ! ! Do not tighten #89226 3x26mm shcs completely until the next step! ! ! ! 89226 x4 3x26mm shcs 89254 Center diff top plate 89124 x2 Brake cam 89019 x2 Center bulkhead (bottom) :: Center Bulkhead Assembly (cont.
:: Shocks Assembly - Bag J 89066 x2 Shock O-rings 89291 16x29mm FT shock body (front) 89352 Spacer 89358 Lower shock tool 89344 16x38mm FT shock body (rear) ! Sho c flui k d Use the lower shock tool to load the two o-rings and spacer for easy lubing and installation into the shock body :: Shocks Assembly (cont.) - Bag J 89215 Locknut (piston) ! Install piston tapered side down.
:: Shocks Assembly (cont.) - Bag J Bladder Installation 89335 Shock cap 89351 Shock bladder A B C As you install the shock cap with the bladder, it will force out any extra fluid. If you install the cap with the shaft fully extended, you are running FULL REBOUND. To run less rebound, unthread the cap 1-2 turns and compress the shaft to the desired position and re-tighten the cap with the shaft compressed. Start with no rebound.
:: Shocks Assembly (cont.) - Bag J 89454 3x12mm shcs 106mm ! ! Install two front shocks. After installation, adjust droop screw to get a front shock length of 106mm measured center to center on the shock cap / eyelet. 91069 Shock mount pin, steel :: Shocks Assembly (cont.) - Bag J ! Note the direction of the shock cap when installing onto shock standoffs ! Note the wing has been hidden for picture clarity only. ! Install two rear shocks.
:: Radio Tray Assembly - Bag K 89004 Receiver box foam pad (bottom) 89003 Wire insert 89253 Antenna mount Receiver not inlcluded! 6338 Antenna tube and cap 89003 Receiver box top 89222 x2 2.5x8mm shcs 89003 Switch mount 89004 Receiver box foam pad (top) On/off switch and mounting screws are not inlcluded! 89003 Receiver box :: Radio Tray Assembly (cont.) - Bag K 21173 x2 Small body clip 5 cell inline pack Receiver 5 cell inline pack configuration shown.
:: Radio Tray Assembly (cont.) - Bag K 89454 x2 3x12mm shcs 89214 4x12mm fhcs 89471 Forward battery box (top) 25187 3x14mm bhcs 89471 Forward battery box foam pad (top) 89471 Forward battery box foam pad (bottom) ! 89471 Forward battery box (bottom) ! Wire routing diagram ! Insert the receiver battery wire into the receiver box! :: Radio Tray Assembly (cont.
:: Radio Tray Assembly (cont.
:: Radio Tray Assembly (cont.) - Bag K 89205 3x26mm bhcs 25203 x6 3x12mm fhcs ! 25215 M3 locknut There will be an unused screw hole at the bottom of the receiver box. This will not be used for the RC8.2 :: Radio Tray Assembly (cont.) - Bag K 0.5mm 89126 x2 Brake washer 89126 x2 brake spring (silicone) 25225 x2 3x3mm setscrew 89126 x2 Set collar ! After installation, leave a 0.
:: Radio Tray Assembly (cont.) - Bag K 1mm gap :: 2 :: 6 :: Brake bias adjusters :: Rear :: 5 :: Front :: 9 :: 1 :: 3 :: 4 ::1 - Turn on transmitter and buggy. Adjust servo horn until position is parallel with centerline at neutral. ::5 - Pull cams to engage brakes. Set collar (with brakes engaged) to have 1mm gap between tubing and collar. ::7 - Set throttle EPA to max. Apply full throttle on transmitter and set EPA so that the carb is full open. Be careful not to over-extend the carb.
:: Air Filter Install - Bag L ! oi filt l # er 77 10 Engine not included! 89142 Air filter outer element When oiling the filter elements, place both inside a plastic bag and squeeze to help evenly coat the filter.
:: Engine Install (cont.) - Bag L 25226 4x5mm setscrew #1596 thread lock 89130 x2 Engine mount plates th #15 re ad 96 lo ck 89144 Pipe mount #1596 thread lock 89145 Pipe wire 89213 x6 4x6mm fhcs 25201 3x8mm fhcs :: Engine Install (cont.
:: Engine Install (cont.) - Bag L Pressure line from fuel tank lid to exhaust pipe nipple Fuel line from fuel tank to carburetor :: Engine Install (cont.) - Bag L 89325 x2 Fuel line clips ! ! ! ! Install fuel line clips! ! Adjust angle of carb ball joint to align with throttle servo.
:: Wheels, Tires, and Body Install - Bag M #0218 Jconcepts Punisher body (sold @jconcepts.net 2208 x2 Large hood pins 31531 3x6mm bhcs Body : Your RC8.2 comes with a clear polycarbonate body. You will need to prep the body before you can paint it. Wash the inside thoroughly with warm water and liquid detergent. Dry using a clean, soft, lint-free cloth. Use the supplied window masks to cover the windows from the INSIDE (RC cars get painted from the inside).
:: Chassis Tips Gearing: Recommended gearing: 16:44. This is a good starting point for most tracks. Follow your engine manufacturer’s recommendations for gearing options. Typically on larger, more open track layouts a 17T clutch bell is used. Gear Mesh: To correctly set your gear mesh, follow the steps below: 1. Loosen the engine mount screws so you can slide your engine from side to side freely. 2. Slide the engine until the clutch bell comes in contact with the spur gear.
:: Rear End Tips Rear Differential: Start with the standard setup. For expert drivers, the most popular setting for buggy is 3,000 cst. the thicker 5,000cst kit oil will rotate less in the turns and accelerate straight on power. The thinner oil (2,000 or 3,000cst) will give more low speed traction. Anti-squat: Anti-squat denotes the angel of the rear inner hinge pin relative to the ground. This setting is adjusted by changing the insert bushing in the C-Plate.
:: Droop Settings (Truggy shown but applicable for all vehicles) Step 1: With only the bottom of the shocks attatched, the droop screws raised all the way, and the chassis above your working surface so the arms are at full extension, you should be able to easily slide the top of your shock over the standoff screw, while leaving the shock at full extension. If the mounting hole of the shock cap is above or below the standoff screw, adjust the droop screw accordingly.
:: Shocks 25612 89066 89067 89083 89215 89278 89290 89291 89335 89344 89346 89351 89352 89353 89354 89355 89469 89492 89554 89555 89556 :: Front and Rear Gear Differential M3 Locknut With Flange Shock O-Rings Shock Limiters, Set Shock Bushings Piston Locknut 2.5mm Washer 16x29mm Front Shock Kit requires #89554 shock shafts for RC8.2 16x29mm Front Shock Body 16mm Shock Caps 16x38mm Rear Shock Body 16x38mm Rear Shock Kit requires #89554 shock shafts for RC8.
:: Top Plate :: Shock Fluid 5420 5421 5422 5423 5424 5425 5426 5427 5428 5429 5430 5431 5432 5433 5434 5435 5436 5437 5438 2oz. 2oz. 2oz. 2oz. 2oz. 2oz. 2oz. 2oz. 2oz. 2oz. 2oz. 2oz. 2oz. 2oz. 2oz. 2oz. 2oz. 2oz. 2oz. 10 Weight Silicone Shock Fluid 20 Weight Silicone Shock Fluid 30 Weight Silicone Shock Fluid 40 Weight Silicone Shock Fluid 22.5 Weight Silicone Shock Fluid 80 Weight Silicone Shock Fluid 27.
:: Front Gearbox 25215 25236 31531 89017 89039 89114 89214 89217 89219 89224 89227 89230 89279 89460 89461 89466 89472 89474 89481 89482 89553 M3 Locknut 8x16x5 Bearing 3x6mm BHCS FR/RR Gearbox Hinge Pin Bushings, Set Diff Pinion Gear 4x12mm FHCS 4x14mm FHCS 3x5mm Setscrew 3x16mm SHCS 3x28mm SHCS Silver Cone Washer 3x45mm SHCS RC8 Aluminum A-Plate RC8 Aluminum B-Plate w/Pins, Set works with #89466 RC8B Inner Hinge Pins, 4mm-HMA, Set works with #89461 RC8B Front Bulkhead Spacer 3x22mm FHCS RC8B Low B Pla
:: Rear Gearbox 25191 25215 25236 31531 89017 89039 89114 89214 89217 89219 89224 89227 89228 89230 89452 89462 89463 89466 3x18mm SHCS M3 Locknut 8x16x5 Bearing 3x6mm BHCS RC8 FR/RR Gearbox, Set RC8 Hinge Pin Bushings, Set RC8 Diff Pinion Gear 4x12mm FHCS 4x14mm FHCS 3x5mm Setscrew 3x16mm SHCS 3x28mm SHCS 3x40mm SHCS Silver Cone Washer 3x50mm SHCS RC8 Aluminum C - Plate RC8 Aluminum D - Plate w/Pins, Set RC8B Inner Hinge Pins, 4mm HMA, Set 20 20 2 6 1 1 1 10 10 10 10 10 10 10 10 1 1 1 89219 89228 31
:: Front Shock Tower 31531 89218 89225 89230 89454 89470 89473 89538 :: Rear Shock Tower 6 10 10 10 10 1 4 1 3x6mm BHCS 3x8mm Washer 3x24mm SHCS Silver Cone Washer 3x12mm SHCS RC8B Shock Tower Hinge Pin Bushings, Set RC8B Steel Shock Stand-offs RC8.
:: Radio Tray 6338 21173 25187 25203 31531 89003 89004 89005 89006 89208 89209 89214 89222 89229 89253 89454 89471 Antenna Tube and Cap 18T Body Clips 3x14mm BHCS 3x12mm FHCS 3x6mm BHCS RC8 Receiver/Battery Box, Set RC8 Receiver Box Pads, Set Aluminum Antenna Mount, Set RC8 Servo Mount Spacers, Set 3x14mm FHCS 3x18mm FHCS 4x12mm FHCS 2.5x8mm SHCS Blue Countersunk Washers Antenna Mount, Set 3x12mm SHCS RC8.
:: Chassis 25201 25226 89018 89022 89130 89144 89145 89207 89213 89224 89231 89257 89476 89552 3x8mm FHCS 4x5mm Setscrew RC8 Gearbox Gasket RC8 Front Bumper RC8 Engine Mount Plates RC8 Pipe Mount RC8 Pipe Mount Wire 4x12mm BHCS 4x6mm FHCS 3x16mm SHCS 3mm Lock Washer RC8 Engine Mount RC8B +3mm Chassis RC8.2 Side Guards 20 20 4 1 2 1 1 10 10 10 10 2 1 Pr.
:: Body / Decals :: Wheels / Tires 89152 89153 89255 89296 89297 RC8 RC8 RTR RC8 RC8 Wheels (White) Wheels (Yellow) Pre-Glued Wheel/Tire (White) 83mm Wheels (White) - Kit 83mm Wheels (Yellow) 4 4 Pr. 4 4 1737 2208 31531 89150 89275 89276 89277 89475 89523 89559 1 6 6 1 1 1 1 1 1 1 FT Body Scissors Large Hood Pins 3x6mm BHCS RC8 Body w/Window Mask (Clear) RC8 RTR Body (Black) RC8 RTR Body (White) RC8 RTR Body Wrap Decals RC8B Decal Sheet RC8e Body w/Window Masks (Clear) RC8.
:: Clutch 25237 89127 89132 89133 89134 89135 89136 89137 89138 89148 89157 89158 89159 89218 89223 89265 89375 89376 :: Exhaust 2 1 1 3 1 1 1 4 1 1 3 3 1 10 10 3 1 1 5x10x4 Bearings Clutch Bell, 17T Clutch Bell, 16T - Kit Clutch Springs 1.0 - Kit Clutch Shoes w/ Shims, Set Clutch Nut Flywheel (Hard Anodized) Clutch Shims Flywheel Collet Clutch Bell Shim Set 0.9 Clutch Springs 1.
:: XP Electronics :: Factory Team and Option Parts 25392 80930 89005 89012 89016 89020 89045 89068 89069 89070 89071 89073 89082 89123 89136 89146 89161 89229 89234 89235 89236 89237 89238 89239 89284 89285 89286 89380 89381 89405 89406 89456 89460 89461 89462 89463 89464 89465 89466 89470 89473 89476 89477 89478 89481 89482 89483 89484 89485 3mm Blue Locknut, Flanged 1/8 Scale Electric Conversion Kit Aluminum Antenna Mount RC8 Steering Rack, Carbon Fiber Servo Saver Bolt, Nut, Spring Center Bulkhead P
:: Reedy Nitro Engines and Parts 800 801 28000 28001 28002 28003 28004 28005 28006 28007 28008 28009 28010 28011 28012 28013 28014 28015 28016 28017 28018 28019 28020 28021 28022 28023 28024 28025 28026 28027 28028 28029 28030 28031 28032 28033 28034 28035 28036 28037 28038 28039 28040 28041 28042 28043 28044 28045 28046 28047 28048 28049 28050 Reedy 121VR .21 Off-Road Comp. Nitro Engine Reedy 121VR-ST .21 Comp.
:: Tools :: 1/12, 1/10 Kits and RTR’s 2033 2042 4019 7023 7027 7029 7030 7032 7034 7036 7037 7046 7047 7048 7049 7080 7092 8020 8021 9036 9039 9061 20515 30105 30106 30111 90004 90005 90006 90007 FT Nitro TC3 Kit Nitro TC3 RTR Plus (ready-to-run) FT 12R5.1 Kit RC10T4.1 FT Kit SC10 2WD Short Course Race Truck Kit SC10 Associated/RC10.com Truck RTR (ready-to-run) SC10 KMC Wheels Race Truck RTR (ready-to-run) SC10 Ready Lift RTR (ready-to-run) SC10 FT Kit RC10T4.1 RTR 2.4GHz Brushed (ready-to-run) RC10T4.
:: Notes
Driver: RC8.2 Track: Setup Sheet Conditions: FT Standard Setup Front Suspension Steering System: Rev.1 Rear Suspension Wheelbase: 3 Anti Roll Bar: Swing Rack Bellcrank Rack 2.2mm 2.3mm 2.4mm 2.5mm Bumpsteer Washers: 0 Camber: -1 Caster: 16 Toe: Date: Event: 2 1 Green White Blue Yellow Front # Up B A 2 Rear # Up 1 dot Down 2.5mm 2.6mm 2.7mm 2.8mm Green White Blue Yellow 6 5 4 -1 Camber: Low Toe Bushing D-Plate Down Ride Height: 28mm Front Shocks Silver 4.
:: Hardware - 1:1 Scale View Flat Head (fhcs) Button Head (bhcs) Cap Head (shcs) 3x8mm (25201) 2.5x8mm (89222) 2.5x3mm (89201) 3x10mm (25202) 3x8mm (89223) 2.
Driver: Track: Setup Sheet Conditions: Front Suspension Steering System: Swing Rack Bellcrank Rack Bumpsteer Washers: Date: Event: Rev.1 Rear Suspension Wheelbase: 3 Anti Roll Bar: 2.2mm 2.3mm 2.4mm 2.5mm 2 3 Long Medium Short 1 Green White Blue Yellow 2 Anti Roll Bar: Camber: Upper Hinge Pin Bushing Caster: Front # Up Toe: B A Rear # Up Down 2.5mm 2.6mm 2.7mm 2.
Associated Electrics, Inc. 26021 Commercentre Dr. Lake Forest, CA 92630 USA http://www.TeamAssociated.com http://www.RC10.com http://twitter/Team_Associated http://bit.ly/AEonFacebook call: (949) 544-7500 - fax: (949) 544-7501 Check out the following web sites for all of our kits, current products, new releases, setup help, tips, and racing info! www.TeamAssociated.com. - www.RC10.
