6/12
:: Introduction Thank you for purchasing this Team Associated product. This manual contains instructions and tips for building and maintaining your new RC8.2e RTR. Please take a moment to read through it an familiarize yourself with these steps as they will help you to understand each component’s function and show you some tips for getting the most out of your RC8.2e RTR. We are continually changing and improving our designs; therefore, actual parts may appear slightly different than the illustrations.
:: Table of Contents 1....................Cover 24-25.........Shocks Install 2....................Introduction 25-30.........Radio Tray Assembly 3....................Table of Contents 4-5...............Front and Rear Diff Assembly 6-7................Center Diff Assembly 7-8...............Steering, Servo, and Rear Camber Links Assembly 8-10.............Shocks Assembly 10.................Chassis Assembly 10-12..........Steering Assembly 12-13..........Front Geaerbox Assembly 14-17..........
:: Front/Rear Differential Assembly 89115 Diff housing 89120 Diff washer 588 #6 rease g k c bla 89121 Diff O-Ring 89496 Diff outdrive 16mm bl 25236 8x16mm bearing # ac 65 8 k gr 8 ea se 89121 Diff O-Ring :: Front/Rear Differential Assembly (cont.) 89120 Sun gear 89120 Diff outdrive pin ! Align pin with groove in sun gear :: Front/Rear Differential Assembly (cont.
:: Front/Rear Differential Assembly (cont.) 89121 Diff O-Ring 89496 Diff outdrive 16mm 89120 Diff washer 89121 Diff O-Ring #6588 black grease 8 e 58 as #6 gre k c la b 25236 8x16mm bearing 89113 Diff ring gear :: Front/Rear Differential Assembly (cont.) 89120 Sun gear 89120 Diff outdrive pin ! Align pin with groove in sun gear :: Front/Rear Differential Assembly (cont.) ! 89116 Diff gasket Tighten screws evenly and firmly.
:: Center Differential Assembly 89115 Diff housing 89120 Diff washer bl 25236 8x16mm bearing # ac 65 8 k gr 8 ea se 89121 Diff O-Ring #6588 black grease 89121 Diff O-Ring 89496 Diff outdrive 16mm :: Center Differential Assembly (cont.) 89120 Sun gear 89120 Diff outdrive pin 89120 Spider gear assembly ! Align pin with groove in sun gear :: Center Differential Assembly (cont.
:: Center Differential Assembly (cont.) 89120 Diff washer 89120 Sun gear 89120 Diff outdrive pin 89121 Diff O-Ring ! Align pin with groove in sun gear :: Center Differential Assembly (cont.) ! 89116 Diff gasket 89208 x4 3x14mm fhcs Tighten screws evenly and firmly. #6588 black grease ! Diff fluid 5,000cst #5453 Fill with diff fluid to top of gears. :: Steering Turnbuckle Assembly 89074 x2 Steering eyelet 89268 42mm steel turnbuckle 17.
:: Servo Link Assembly 89078 x2 Straight eyelet 89267 32mm steel turnbuckle 7.5mm 89078 x2 balljoint :: Rear Camber Link Assembly 89076 x2 Camber pivot balls 89076 x2 Camber rod end 89269 38mm steel turnbuckle 89076 x2 Camber ball joints 7.
:: Shock Assembly - (cont.) 89215 Locknut (piston) 89353 Shock piston set (1.3, blank) 89260 Shock shaft, 29mm, (front) 89352 O-Ring 89278 x2 2.5mm piston washer 89261 Shock shaft, 38mm (rear) 89352 Bottom nut 89358 Upper shock tool :: Shock Assembly - (cont.) ! ! Sho c flui k d Short boots for front shocks. Fill to top with shock fluid: Long boots for rear shocks. Front: 30wt Rear 30 wt #5422 89556 RC8.2 shock boot (front shown) ! ck Sho d flui One drop of shock fluid on threads.
:: Shock Assembly - (cont.) 89293 x2 Front spring, silver (3.9lbs) (short spring) 89348 x2 Rear spring, silver (3.3lbs) (long spring) Front shock: 7mm Rear shock: 2mm 89396 Shock pre-load clips 89396 Shock pre-load clips 1mm 2mm 3mm 5mm 10mm 89354 16mm shock spring cup ! Build two front and two rear shocks! :: Chassis Assembly 89552 x2 Side guards (left & right) ! Note: cut fuel tubing brace off of the left side guard.
:: Steering Assembly (cont.) 31404 x2 6x10mm bearing 89016 Servo saver bolt 89015 Servo saver arm #65 88 ck gre ase bla 89015 Servo saver bellcrank ! gap setting: 2mm # thr 1596 ea dl ock 89117 x2 Diff shim 89016 Servo saver spring 89016 Servo saver retainer :: Steering Assembly (cont.) 89272 Steering rack 31404 x2 6x10mm bearing 89161 x4 5x8mm bearing 89015 Steering bellcrank 89014 x2 Steering rack post 89218 x2 Washer 3x8mm 25215 x2 M3 locknut :: Steering Assembly (cont.
:: Steering Assembly (cont.) / Front Gearbox Assembly #1596 thread lock 89214 x2 4x12mm fhcs #1596 thread lock 89114 Diff pinion gear 25215 x4 M3 locknut 25236 x2 8x16mm bearing 89017 Inner gearbox :: Front Gearbox Assembly - (cont.) 89278 x2 2.5mm washer ! 89036 Arm mount (B) Key setscrew onto flat side of shaft. Tighten with no endplay. 89221 5x4mm setscrew 89571 SC8.2e center drive line input cup 96 #15 lock d a e thr 89201 x2 2.
:: Front Gearbox Assembly - (cont.) 89225 x2 3x24mm shcs 96 #15 lock ad e r th 89549 Front upper arm 89473 x2 Steel shock standoffs 96 #15 lock ad e thr 89218 x2 3x8mm washer 89586 RC8.2e RTR shock tower (front) 89269 38mm steel turnbuckle 89076 Camber rod ends 7.5mm ! Smooth edge towards drivers side! Build right and left sides! :: Front Gearbox Assembly - (cont.
:: Front Suspension Assembly 89102 CVA bone 89105 CVA pin #6588 black gre ase 8 #658 e greas black 89105 CVA u-joint coupler 89573 Lightweight cv axle, steel ! ! ! Axle has additional holes for crosspin to extend the life of the Axle. Build Two! :: Front Suspension Assembly - (cont.
:: Front Suspension Assembly - (cont.) 89029 Steering block bushing (short) Note: direction ! 89206 4x10mm bhcs blue 16 deg 16 deg red 89032 16 deg. caster angle bushing (red) 89029 Steering block bushing (long) ! Do not tighten until bushing is keyed into steering block. 89207 4x12mm bhcs ! 89032 16 deg. caster angle bushing (blue) Note: Key bushings into steering block. ! Build right and left sides! :: Front Suspension Assembly - (cont.
:: Front Suspension Assembly - (cont.) ! Build right and left sides! hinge pin bushing 2 dot down 25215 x2 M3 locknut 89039 x2 Hinge pin bushings (two dot, down) 89035 Arm mount (A) 89228 x2 3x40mm shcs 89218 x2 3x8mm washer :: Front Suspension Assembly - (cont.) Side View 89031 x4 Blue 1.7mm caster spacer 25215 x2 M3 locknut 89225 x2 3x24mm shcs ! Build right and left sides! :: Front Suspension Assembly - (cont.) 25225 x2 3x3mm setscrew # thr 1596 ead loc k 89088 2.
:: Front Suspension Assembly - (cont.) 25215 M3 locknut 89022 Front bumper 89217 x2 4x14mm fhcs 89214 x4 4x12mm fhcs #15 9 ead 6 lock thr 25204 3x16mm fhcs :: Rear Gearbox Assembly 25215 x2 M3 locknut 25236 x2 8x16mm bearing 89114 Diff pinion gear ! Key setscrew onto flat side of shaft. Tighten with no endplay. 89221 5x4mm setscrew 89571 SC8.
:: Rear Gearbox Assembly - (cont.) 89039 x2 Hinge pin bushing (2 dot down) hinge pin bushing 89037 Arm mount (C) 2 dot down 89211 3x26mm fhcs 89258 Chassis brace (rear) 89218 x2 3x8mm washer 89224 x2 3x16mm shcs 25215 M3 locknut :: Rear Gearbox Assembly - (cont.) 89225 x2 3x24mm 89473 x2 shcs Steel shock standoff 89011 Body mount and spacer 25215 x2 M3 locknut #15 9 ead 6 lock thr 89218 x2 3x8mm washer 25192 x2 3x20mm shcs 89587 RC8.
:: Rear Gearbox Assembly - (cont.) ! 89472 Front bulkhead spacer Diff shims installed to diff, diff installed to gearbox. ! ! 89224 x2 3x16mm shcs 89117 x2 Diff shim 89017 Outer gearbox :: Rear Suspension Assembly 89162 15x21mm bearing ! th #15 re ad 96 lo ck 89572 SC8.2e dogbone axle 89107 Bearing shield Build right and left sides! 89096 Wheel hex pins 89033 hub carrier (left, right) 25236 8x16mm bearing 89251 Wheel hex 89221 5x4mm setscrew :: Rear Suspension Assembly - (cont.
:: Rear Suspension Assembly - (cont.) ! Build right and left sides! 31520 2.5x6mm bhcs 89031 x2 Hub spacers (red) 89575 x2 SC8.2e dogbone (82mm) 89041 Outer hinge pin :: Rear Suspension Assembly - (cont.) 89278 x2 2.5mm washer 89201 x2 2.5x3mm bhcs 89038 Arm mount (D) 89218 x2 3x8mm washer 89228 x2 3x40mm shcs # thr 1596 ead loc k 89040 x2 Inner hinge pins :: Rear Suspension Assembly - (cont.) 25215 M3 locknut 89089 2.
:: Rear Suspension Assembly - (cont.) 89202 x2 3x12mm bhcs 89218 x2 3x8mm washer 89592 RC8.2e RTR wing (black) 25192 x2 3x20mm shcs 89540 RC8.2 wing mount upper brace 25215 x2 M3 locknut 89540 x2 RC8.2 wing mounts 25215 x2 M3 locknut :: Rear Suspension Assembly - (cont.
:: Rear Suspension Assembly - (cont.) 25215 M3 locknut 89217 x2 4x14mm fhcs 25204 3x16mm fhcs 89214 x2 4x12mm fhcs :: Center Bulkhead Assembly 31532 x2 3x8mm bhcs Motor 89501 Motor mount 89528 x2 3x5.
:: Center Bulkhead Assembly - (cont.) 89510 Motor pad 89584 RC8.2e RTR dogbone (96mm, front) 89583 RC8.2e RTR dogbone (99mm, rear) :: Center Bulkhead Assembly - (cont.
:: Shocks Install 89083 Shock bushing ! Note the direction of the shock cap when installing onto shock standoffs ! Install two front shocks. 25612 M3 locknut with flange :: Shocks Install - (cont.) 89454 3x12mm shcs ! After installation, adjust droop screw to get a front shock length of 103mm measured center to center on the shock cap / eyelet. 91069 Shock mount pin, steel :: Shocks Install - (cont.
:: Shocks Install - (cont.) 89454 3x12mm shcs ! After installation, adjust droop screw to get a rear shock length of 122mm measured center to center on the shock cap / eyelet. 91069 Shock mount pin, steel :: Radio Tray Assembly 25187 x4 3x14mm bhcs 89506 x3 Hook and loop battery straps Servo 89218 x4 3x8mm washer 89006 x4 Servo spacers ! 89504 Radio tray (bottom) 89505 RC8e battery tray Servo mounts vary per servo manufacturer.
:: Radio Tray Assembly - (cont.) ! Note: hook and loop straps are removed for view clarity. 89507 Battery tray pads ! Bottom View 89509 Flywheel opening cover :: Radio Tray Assembly - (cont.) 89216 x2 M4 locknut ! Note: there are two different positions for the locknuts depending on what vehicle you have. 25215 x2 M3 locknut RC8.2e ! 89509 Battery tray post RC8Te SC8e Note: hook and loop straps are removed for view clarity. RC8Te SC8e RC8.2e Front :: Radio Tray Assembly - (cont.
:: Radio Tray Assembly - (cont.) ! ! Note: route the speed control receiver wire up and over the bridge Note: route the speed control receiver wire through the radio box hole. ! Note: route the servo wire to the receiver through this opening. :: Radio Tray Assembly - (cont.) 31531 x2 3x6mm bhcs Receiver ! Note: transponder not included. ! Note: hook and loop straps are removed for view clarity. ! Note: plug in your speed control and servo to your receiver.
:: Radio Tray Assembly - (cont.) A - Airtronics F - Futaba H - Hitec J - JR Printed here ! 25201 3x8mm fhcs 25215 M3 locknut 89007 Servo horn ring 96 #15 ck ad lo thre 89007 Servo cone washer ! Enlarge holes in servo horn! 89007 Steering servo horn 2308 3x18mm bhcs :: Radio Tray Assembly - (cont.) ! Note: hook and loop straps are removed for view clarity.
:: Radio Tray Assembly - (cont.) 89214 x2 4x12mm fhcs 89211 x2 3x26mm fhcs 89213 x2 4x6mm fhcs :: Radio Tray Assembly - (cont.
:: Radio Tray Assembly - (cont.) ! 3719 Nylon wire tie (6” ) Note: batteries not included. ! Note: hook and loop straps are removed for view clarity. ! ! ! Note: Install wire tie as shown. :: Wheels, Tires, and Body Install 89255 x4 RTR Pre-glued wheel/tire 97 #15 e e glu r i t CA Tires: When gluing tires to wheels, use a fast-curing Tire glue (CA) (AE Pt#1597). This is available at your local hobby shop. Make sure to clean the mounting surface of the tire with alchohol for best adhesion.
:: Wheels, Tires, and Body Install 89252 x4 Wheel hex nuts (silver) :: Wheels, Tires, and Body Install (cont.
:: Chassis Tips Gearing: Follow your motor manufacturer’s recommendations for gearing options. Gear Mesh: To correctly set your gear mesh, follow the steps below: 1. Loosen the set screw on the motor’s pinion gear. The set screw can be accessed through the slot on the side of the motor mount slide, opposite the spur gear. Slide the pinion on the motor shaft until the gear face of the pinion is entirely aligned with the gear face of the spur gear (see diagram).
:: Front End Tips (cont.) Front Camber Angle: A good starting camber setting is –2 degrees. Positive camber, where the top of the tire is leaning out, is typically not recommended. Front Toe-In: Zero degree toe-in (tires pointing straight forward) is a good starting setting. You can increase turn in by adding 1-2 degrees of toe-out (front of tires point slightly out). Front toe - in is not a typical tuning adjustment used by the Team.
:: Droop Settings (Buggy shown but applicable for all vehicles) Note: Rear hub spacing is not recommended with RTR dog bones. For more adjustability, use CVA’s in place of dog bones. Step 1: With only the bottom of the shocks attatched, the droop screws raised all the way, and the chassis above your working surface so the arms are at full extension, you should be able to easily slide the top of your shock over the standoff screw, while leaving the shock at full extension.
:: Shocks 25612 89065 89066 89067 89083 89215 89260 89261 89278 89335 89351 89352 89353 89354 89396 89556 89580 89582 :: Front and Rear Gear Differential M3 Locknut With Flange Shock Rod End Shock O-Rings Shock Limiters, Set Shock Bushings Piston Locknut 29mm RTR Shock Shaft, Front 38mm RTR Shock Shaft, Rear 2.5mm Washer 16mm Shock Caps 16mm Shock Bladders 16mm Shock Rebuild Kit 16mm Shock Pistons 16mm Shock Spring Cups 16mm RTR Pre-load Clips, Shock Collar Set RC8.
:: Top Plate :: Shock Fluid 5420 5421 5422 5423 5424 5425 5426 5427 5428 5429 5430 5431 5432 5433 5434 5435 5436 5437 5438 10 Weight Silicone Shock Fluid 20 Weight Silicone Shock Fluid 30 Weight Silicone Shock Fluid 40 Weight Silicone Shock Fluid 22.5 Weight Silicone Shock Fluid 80 Weight Silicone Shock Fluid 27.5 Weight Silicone Shock Fluid 15 Weight Silicone Shock Fluid 25 Weight Silicone Shock Fluid 35 Weight Silicone Shock Fluid 45 Weight Silicone Shock Fluid 55 Weight Silicone Shock Fluid 32.
:: Front Gearbox 25215 25236 31531 89017 89035 89036 89040 89039 89114 89201 89214 89217 89218 89219 89221 89224 89226 89228 89278 89472 89571 89584 20 2 10 1 1 1 1 1 1 10 10 10 10 10 10 10 10 10 20 2 2 1 M3 Locknut 8x16x5 Bearing 3x6mm BHCS FR/RR Gearbox Arm Mount A Arm Mount B Inner Hinge Pin, Set Hinge Pin Bushings, Set Diff Pinion Gear 2.5x3mm BHCS 4x12mm FHCS 4x14mm FHCS 3x8mm Washer 3x5mm Setscrew 5x4mm Setscrew 3x16mm SHCS 3x26mm SHCS 3x40mm SHCS 2.5mm Washer RC8B Front Bulkhead Spacer SC8.
:: Rear Gearbox 25215 25236 31531 89017 89037 89038 89039 89040 89114 89201 89211 89214 89217 89218 89219 89221 89224 89278 89279 89472 89571 89583 M3 Locknut 8x16x5 Bearing 3x6mm BHCS RC8 FR/RR Gearbox, Set Arm Mount C Arm Mount D RC8 Hinge Pin Bushings, Set Inner Hinge Pin, Set RC8 Diff Pinion Gear 2.5x3mm BHCS 3x26mm FHCS 4x12mm FHCS 4x14mm FHCS 3x8mm Washer 3x5mm Setscrew 5x4mm Setscrew 3x16mm SHCS 2.5mm Washer 3x45mm SHCS RC8B Front Bulkhead Spacer SC8.2e Center Drive Line Input Cup RC8.
:: Front Shock Tower 89039 89202 89218 89225 89473 89586 :: Rear Shock Tower 1 10 10 10 4 1 Hinge Pin Bushings, 1/2/3dot Set 3x12mm BHCS 3x8mm Washer 3x24mm SHCS RC8B Steel Shock Stand-offs RC8.2e RTR Front Shock Tower 25192 25215 89011 89218 89225 89454 89473 89587 89225 89218 20 20 1 10 10 10 4 1 3x20mm SHCS M3 Locknut Body Mount Set 3x8mm Washer 3x24mm SHCS 3x12mm SHCS RC8 Steel Shock Standoffs RC8.
:: Radio Tray 2308 6338 21173 25187 25201 25203 25215 31531 89006 89007 89078 89205 89211 89213 89214 89216 89218 89219 89222 89267 89504 89505 89506 89507 89509 3x18mm BHCS Antenna Tube and Cap 18T Body Clips 3x14mm BHCS 3x8mm FHCS 3x12mm FHCS M3 Locknut 3x6mm BHCS RC8 Servo Mount Spacers, Set Steering Servo Horns, Set RC8 Servo Link Rod Ends, Set 3x26mm BHCS 3x26mm FHCS 4x6mm FHCS 4x12mm FHCS M4 Locknut 3x8mm Washer 3x5mm Setscrew 2.
:: Anti-Swaybars 4671 25225 89086 89087 89088 89089 89091 89093 89511 :: Wing 3x10mm Setscrew 3x3mm Setscrew FT Antiroll Bar Set FT Antiroll Bar Black, 2.2mm FT Antiroll Bar Silver, 2.5mm - Kit (rear) FT Antiroll Bar Gold, 2.8mm - Kit (front) FT Antiroll Bar Socket Joint FT Antiroll Bar Black, 3.0mm RC8.
:: Factory Team and Option Parts 25392 31550 80930 89005 89012 89016 89020 89045 89053 89054 89070 89071 89073 89082 89094 89095 89160 89161 89229 89234 89235 89236 89237 89284 89285 89286 89290 89291 89320 89321 89344 89346 89355 89378 89379 89380 89381 89405 89406 89456 89460 89461 89462 89463 89466 89467 89468 89469 89470 89473 89477 89478 89481 89482 89485 89487 89488 89489 89490 89492 89494 89529 89530 89531 89532 89533 89534 89535 89536 89537 89541 3mm Blue Locknut, Flanged M3 Aluminum Lock Nut 1/
:: Reedy Accessories 654 655 656 657 658 659 716 978 979 980 981 982 SP35M SP35L SP35XL SP35XXL SP35XXXL SP36M SP36L SP36XL SP36XXL SP36XXXL SP37S SP37M SP37L SP37XL SP37XXL SP37XXL SP38 SP39 SP418 4.0mm plugs (2M, 2F) 4.0mm plugs (2M, 10F) 4.0mm plugs (10F) 4.0mm plugs (100F) 4.0mm plugs (10M) 4.
:: Tools 1111 1112 1449 1450 1541 1542 1543 1544 1545 1546 1547 1548 1551 1553 1554 1561 1562 1563 1564 1565 1567 1589 1590 1592 1655 1656 1657 1658 1659 1660 1661 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671 1672 1673 1674 1719 1737 3718 3719 3720 3987 6429 6956 7494 7709 91107 FT Turnbuckle Wrench FT 4mm Turnbuckle Wrench (4x4 only) Offroad Ride Height Gauge FT Ride Height Gauge FT Hex Driver Set, (7 pcs) FT .050” Silver Hex Driver FT 1/16” Black Hex Driver FT 1.
:: Notes
:: Notes
Driver: Track: Setup Sheet Conditions: Front Suspension Anti Roll Bar: Steering System: 2.2mm 2.5mm 2.8mm 3.0mm Black Silver Gold Black 0 Camber: -1 3 2.2mm 2.5mm 2.8mm 3.0mm 1 Front # Up B A 3 Black Silver Gold Black 2 Rear # Up 1 dot Down Long Medium Short 6 5 4 -2 Camber: Low Toe Bushing D-Plate Down Ride Height: # 29mm Front Shocks Front Silver 3.9 Spring: 30 weight Shock Fluid: 16mm Piston: Hub: Upper Lower Squat Bushing C-Plate O I 2 dot Up Down Shock Cap: Alum.
:: Hardware - 1:1 Scale View Flat Head (fhcs) Button Head (bhcs) Cap Head (shcs) 3x8mm (25201) 2.5x8mm (89222) 2.5x3mm (89201) 3x10mm (25202) 3x8mm (89223) 2.
Driver: Track: Setup Sheet Conditions: Front Suspension Anti Roll Bar: Steering System: 2.2mm 2.5mm 2.8mm 3.0mm Black Silver Gold Black 3 2 2.2mm 2.5mm 2.8mm 3.0mm 1 back mid front Camber: Caster: Front # Up B A 3 Black Silver Gold Black 2 1 Wheelbase: Upper Hinge Pin Bushing Toe: Rev.
Associated Electrics, Inc. 26021 Commercentre Dr. Lake Forest, CA 92630 USA http://www.TeamAssociated.com http://www.RC10.com http://twitter/Team_Associated http://bit.ly/AEonFacebook call: (949) 544-7500 - fax: (949) 544-7501 Check out the following web sites for all of our kits, current products, new releases, setup help, tips, and racing info! www.TeamAssociated.com. - www.RC10.