2/13
:: Introduction Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new SC10.2. Please take a moment to read through this manual to help familiarize yourself with these steps. We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags.
:: Table of Contents 1................... Cover 2................... Introduction 3................... Table of Contents 4................... Steering Build (Bag A-AA) 4 - 5............. Front End, Outer Build (Bag B-BB) 5 - 7............. Front End, Inner Build (Bag C) 7 - 10...........Transmission Build (Bag D-DD) 10 - 13........Rear End Build (Bag E-EE) 13 - 14........ CVA and Turnbuckle Build (Bag F-FF) 16 - 18........ Electronics Build (Bag H-HH) 19.................
:: Steering Build - Bag A-AA - Step 1 3981 x2 Ballstud, .20 black, short 9647 x2 Block carrier bushing 6272 Dust cover foam 9679 FT Aluminum Bellcrank Set 6272 x2 Dust cover foam 596 ck #1 lo ad e r th ! ! 9659 Steering rack 6917 x2 4-40x3/8 bhcs ! 6276 Ballstud, .
:: Front End, Outer Build - Bag B-BB - Step 2 ! Align the C-clip on the front axles with the D-shape inside the steering blocks. 6272 Dust cover foam 7369 1/16 universal roll pin 3983 Ballstud, .
:: Front End, Inner Build - Bag C - Step 2 9899 x2 Front body post 6917 4-40x3/8 bhcs 9899 Front body mount 9667 x2 2-56x5/8 shcs :: Front End, Inner Build - Bag C - Step 3 1780 x2 FT aluminum shock bushings, standard 596 ck #1 d lo a e thr 9630 x2 .
:: Front End, Inner Build - Bag C - Step 5 Front Camber Turnbuckle 1.92” (48.75mm) ! Orient the notch to the left throughout the car. It indicates which end has the left hand threads! 7230 x2 ball cup (large) 1408 2.65” Ti turnbuckle Steering Turnbuckle 2.07” (52.75mm) 7230 x2 ball cup (large) 1417 2.
:: Transmission Build - Bag D-DD - Step 2 6573 x2 Diff thrust washer #6588 black grease 6574 x6 5/64 diff thrust balls 6589 x2 5/32 x 5/16, unflanged bearing 6573 Diff thrust bolt :: Transmission Build - Bag D-DD - Step 3 As you tighten the diff bolt, you will notice the T-nut ears moving closer to the bottom of the outdrive slot. This compresses the spring behind the T-nut. The spring should be completely compressed at the same time the T-nut reaches the end of the slot.
:: Transmission Build - Bag D-DD - Step 5 ! Install the Diff with the head of the Diff Thrust Bolt (#6573) facing the right side of the transmission case! 6919 x2 4-40x5/16 bhcs 9630 x3 .
:: Transmission Build - Bag D-DD - Step 8 ! 9603 Slipper pad 7485 FT V2 slipper hub ! 91176 VTS slipper housing 91178 VTS slipper plate ! 9653 84T 48P spur gear There’s also a 75T 48P Spur Gear (#9650) included for stock motors use! 91179 VTS slipper hub, outer 91177 x2 VTS slipper pads :: Transmission Build - Bag D-DD - Step 9 ! ! 9739 Slipper spring Set nut flush with top shaft. Compress spring first.
:: Rear End Build - Bag E-EE - Step 2 9269 x2 5-40x1/2 fhcs 9269 x4 5-40x1/2 fhcs :: Rear End Build - Bag E-EE - Step 3 6277 x2 Ballstud .
:: Rear End Build - Bag E-EE - Step 5 6922 4-40x1/2 fhcs :: Rear End Build - Bag E-EE - Step 6 6915 x2 4-40x5/8 fhcs 6924 x2 4-40x3/8 shcs :: Rear End Build - Bag E-EE - Step 7 9899 x2 Front body post 9899 Rear body mount 6924 x4 4-40x3/8 shcs 9667 x2 2-56x5/8 shcs
:: Rear End Build - Bag E-EE - Step 8 89430 x2 Mud flaps 9817 Ream bumper 89218 x2 3x8mm washer 6925 x4 4-40x1/2 shcs 6917 x2 4-40x3/8 bhcs :: CVA and Turnbuckles Build - Bag F-FF - Step 1 4449 4-40x3/16 aluminum locknut 9917 Aluminum hub A, carbon Left Side 3981 Ballstud, .
:: CVA and Turnbuckles Build - Bag F-FF - Step 3 Build x2 (right and left side) 7369 1/16 roll pins 31286 FT ballstud washer, aluminum (1mm) 9892 12mm aluminum clamping wheel hex, rear 9898 2-56x3/16 shcs 9645 2-56x1/8 bhcs Build x2 (right and left side) 9622 Hinge pin, rear outer 9630 .030 ballstud washer :: CVA and Turnbuckles Build - Bag F-FF - Step 4 ! Orient the notch to the left throughout the car. It indicates which end has the left hand threads! Steering Turnbuckle 2.10” (53.
:: Shocks Build - Bag G-GG - Step 2 91300 12x27.
:: Shocks Build - Bag G-GG - Step 5 6472 x2 Shock mount nut ! ! Use inside hole in rear arm! Use outside hole in front arm! 6472 x2 Shock mount nut 6927 x2 4-40x3/4 shcs 6925 x2 4-40x1/2 shcs :: Electronics Build - Bag H-HH - Step 1 3981 Ballstud, .
:: Electronics Build - Bag H-HH - Step 3 Motor not included! 31532 x2 M3x8mm bhcs 6936 x2 Washer #4 aluminum :: Electronics Build - Bag H-HH - Step 4 Pinion / Setscrew not included! ! See page 20 for gear mesh setting instructions! :: Electronics Build - Bag H-HH - Step 5 3862 5-40x1/8 set screw 6338 Antenna tube & cap Receiver / Servo tape not included! 7461 Gear cover button 7461 Gear cover (clear) 6285 x2 4-40x1/4 shcs ESC/ Servo tape not included!
:: Electronics Build - Bag H-HH - Step 6 9815 x2 Foam spacer ! 9879 x2 Thumb knob Trim the battery foam 18mm to move the battery pack towards the back. ! 9879 x2 4-40x1/2 set screw GAP * Leave a 2.5mm gap :: Electronics Build - Bag H-HH - Step 7 9851 FT SC10 carbon fiber battery strap Battery not included! ! Move thumb knobs to the unlocked position and remove the battery strap to remove your battery pack.
:: Wheels / Tires and Body - Bag I - Step 1 91101 x4 KMC hex wheel, black ! Carefully apply ca glue to the tire bead.
:: Tuning Tips Tips for Beginners: Before making any changes to the standard setup, make sure you can get around the track without crashing. Changes to your vehicle will not be beneficial if you can’t stay on the track. Your goal is consistent laps. Once you can get around the track consistently, start tuning your vehicle. Make only ONE adjustment at a time, testing it before making another change.
:: Tuning Tips (cont.) Front Camber Links: Changing the length of the camber link is considered a bigger step than adjusting the ball end height on the tower. Shortening the camber link (or lowering the ball end) will give the front end less roll and quicken steering response. Lengthening the camber link (or raising the ball end) will give the front more roll and slower steering response.
:: Shocks 1777 4187 5407 6299 31327 31510 91300 91302 91303 91304 91306 91307 91308 91309 91310 91315 91317 :: Ball Differential FT Blue Aluminum Shock Pivot Ball with Eyelet .030 Nylon Washer Red O-Rings E-Clip VCS3 Shock Bottom Cap and O-Ring M2 x 4mm BHCS 12X27.5mm FT Shock Bodies (front) 12X36mm FT Shock Bodies (rear) 12MM Shock Cap 12MM Threaded Collar and O-Ring 27.5X3mm TiN Shock Shaft (front) 35X3mm TiN Shock Shaft (rear) 12MM Shock Pistons, (1.5, 1.6, 1.
:: Slipper Clutch 6285 6629 7461 7485 7486 9603 9649 9650 9651 9652 9653 9739 91175 91176 91177 91178 91179 4-40 x 1/4” SHCS 5-40 Diff Locking Nut Molded Gear Cover, Clear FT V2 Slipper Hubs FT V2 Slipper Spring and Washer Slipper Pad 72T 48P Spur Gear 75T 48P Spur Gear 81T 48P Spur Gear (Kit) 78T 48P Spur Gear 84T 48P Spur Gear Slipper Spring FT VTS Slipper Conversion VTS Slipper Housing VTS Slipper Pads VTS Slipper Plate FT VTS Slipper Hub, outer 12 6 1 2 1 2 1 7485 1 1 1 1 1 1 1 2 1 1 9603 91176 91
:: Front Bulkhead / Steering 3971 3981 6272 6276 6917 6922 9566 9640 9647 9659 9679 89229 .125 x .250 x .109“ Bearings Ballstud .20 Black, short Foam Ball end Dust Covers Ballstud .
:: Battery Strap 9238 9815 9851 9879 Foam Battery Spacers, Set Foam Battery Spacer FT SC10 Carbon Fiber Battery Strap SC10 RTR Battery Strap (includes setscres and thumb knobs) 1 1 1 1 9879 9879 9851 9815 9879 9879 9238 :: Rear Shock Tower 1781 6332 6472 6915 6924 7413 9643 9644 9667 9824 9899 FT Shock Bushings, short, (blue) Body Clips 4-40/5-40 Plastic Nut 4-40 x 5/8” FHCS 4-40 x 3/8” SHCS 4-40 x 3/4” BHCS 5-40 x 7/16” SHCS 5-40 x 9/16” SHCS 2-56x5/8 SHCS T4 Rear Shock Tower SC10.
Steering :: FrontBlock, Arm Hex 3977 3983 4449 6272 6277 6927 6953 7369 7922 9621 9622 9645 9880 9881 9882 9893 9898 31286 91201 Ball Bearing 3/16” x 3/8” Ballstud .30” Black (short) 4-40 x 3/16 Aluminum Locknut Foam Ballend Dust Covers Ballstud .
:: Transmission 1770 3977 6913 6919 6922 6924 6925 6928 6936 9360 9361 9601 9602 9630 9819 9826 9832 31532 :: Pinion Gears FT Milled Motor Plate, blue Ball Bearing, 3/16” x 3/8“ 4-40 x 1 1/4” SHCS 4-40 X 5/16” BHCS 4-40 X 1/2” FHCS 4-40 X 3/8” SHCS 4-40 x 1/2” SHCS 4-40 x 1” SHCS #4 Washer, aluminum Idler Gear, molded Idler Gear Shaft B4/T4 Top Shaft B4/T4 Top Shaft Spacer Ballstud Washer Rear Motor Guard Transmission Case for Gear Diff (left & right) Ball Bearing, 10 x 16mm M3 x 8mm BHCS 31532 16T 1
:: Chassis 3862 4334 6272 6277 6338 6915 6917 7487 7488 9269 9563 9564 9621 9643 9645 9665 9818 9822 9823 31286 5-40 x 1/8” Set Screw 2-56 x 5/16” BHCS Foam Ballend Dust Cover Ballstud .30” Silver (long) Antenna Tube & Cap (black) 4-40 X 5/8” FHCS 4-40 x 3/8” BHCS Arm Mounts 2.5, 3, 3.
:: Factory Team and Option Parts 1283 1408 1409 1654 1734 1735 1736 1770 1777 1778 1779 1780 1781 1787 3971 6906 6937 6943 7381 7441 7445 7449 7453 7455 7485 7486 7487 7922 7990 9565 9567 9592 9593 9598 9600B 9635 9665 9678 9679 9739 9755 9789 9795 9796 9797 9798 9799 9864 9865 9866 9867 9872 9917 9918 31237 31286 91175 91176 91177 91178 91179 1 FT Ti Turnbuckle Set, T4 Pr. FT Ti Turnbuckle, 2.65” (blue) Pr.
:: LRP Speed Controls :: Reedy Accessories 604 605 606 607 654 655 656 658 659 660 661 663 664 716 959 960 961 962 972 973 974 975 978 979 980 981 982 992 526-S AC/DC 2S-6S LiPo/LiFe Charger Motor Cooling Fans (2) Charge Harness 2S Saddle Pack 4mm Charge Harness 2S Standard Pack 4mm 4.0mm plugs (2M, 2F) 4.0mm plugs (2M, 10F) 4.0mm plugs (10F) 4.0mm plugs (10M) 4.0mm plugs (30M) 3.5mm plugs (3M, 3F) 3.5mm plugs (10F) 3.5mm plugs (10M) 3.
:: Qualifier Series Vehicles 7052 20510 30112 Pro Lite 4x4 RTR, 1/10 Scale (ready-to-run) RIVAL Electric Monster Truck RTR, 1/8 Scale (ready-to-run) APEX Touring V-Type, 1/10 Scale (ready-to-run) :: Lubes & Adhesives / Decals / Misc. 1 1 1 :: 1/18 Kits and RTR’s 20103 20121 RC18B2 - RC18T2 Team Kit SC18 RTR Brushless (ready-to-run) 1 1 1105 1596 1597 6588 6591 6636 6727 FT Green Slime Shock Lube FT Locking Adhesive FT Tire Adhesive, medium Black Grease - 4cc S.
:: Apparel :: Tools 1111 1113 1449 1541 1542 1543 1544 1545 1546 1547 1548 1551 1553 1554 1561 1562 1563 1564 1565 1567 1589 1590 1592 1655 1656 1657 1658 1659 1660 1661 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671 1672 1673 1674 1719 1737 3718 3719 3720 3987 6429 6956 7494 7709 FT Turnbuckle Wrench 12mm Big Bore Shock Tool FT Off Road Ride Height Gauge FT Hex Driver Set, (7 pcs) FT .050” Silver Hex Driver FT 1/16” Black Hex Driver FT 1.
:: Notes
:: Notes
SC10.2 FT Stock Setup Driver: Date: Track: Event: Conditions: Indoor Outdoor Temp. Setup Sheet Front Suspension Rev.1 Rear Suspension Camber: Toe: 3 12 1 -1 ° 23 Camber: Inner Toe: 0 ° Anti-Squat: -1 ° 3 ° 2 ° Washers: 1mm 2mm Washers: 2mm 12 AB C 12 Ride Height: AB C D Chassis Brace Ground Flat: 30mm I O IO Caster Block Spacing: Forward Back Steering Rack: Caster: Front Back Washers: 2mm 20° 25° 30° Front Shocks Gray 1.
:: Hardware - 1:1 Scale View Cap Head (shcs) Button Head (bhcs) Flat Head (fhcs) 2-56x 3/16 (9898) 4-40x3/8 (6292) 2-56x1/8 (9645) 4-40x1/4 (6285) 4-40x1/2 (6922) 2-56x5/16 (4334) 4-40x5/16” (6932) (4145, aluminum) 4-40x5/8 (6915) 4-40x1/4 (6288) 4-40x3/8 (6924) w/hole (6929) 5-40x1/2 (9269) 4-40x1/2 (6925) 4-40x5/16 (6919) 4-40x3/8 (6917) 4-40x7/16 (2221) Shims and Washers 4-40x5/8 (6926) 4-40x3/4 (7413) .030 Ballstud Washer (9630) 4-40x3/4 (6927) 4-40x7/8 (91311) .
Driver: Track: Conditions: Setup Sheet Indoor Front Suspension Date: Event: Outdoor Temp. Rev.
Associated Electrics, Inc. 26021 Commercentre Dr. Lake Forest, CA 92630 USA http://www.TeamAssociated.com http://www.RC10.com http://twitter/Team_Associated http://bit.ly/AEonFacebook call: (949) 544-7500 - fax: (949) 544-7501 Check out the following web sites for all of our kits, current products, new releases, setup help, tips, and racing info! www.TeamAssociated.com. - www.RC10.
