0/12
:: Introduction Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new SC10B RS RTR. Please take a moment to read through this manual to help familiarize yourself with these steps. We are continually changing and improving our designs; therefore, actual parts may appear slightly different than the illustrations. New parts will be noted on supplimentary sheets located in the appropriate parts bags.
:: Table of Contents 1....................Cover 19 - 23........Roll cage 2....................Introduction 3....................Table of Contents 24.................Wheels and Tires 4 - 5..............Steering System 27 - 38........Catalog 5 - 8..............Front Suspension 38.................Contact Information 8 - 10...........Transmission 39................Setup Sheet “RTR Setup” 11 - 12........Rear Suspension 40.................1:1 Hardware “Fold Out” 13.................Rear Hubs 41.
:: Steering System 9610 Servo saver bolt ! 9610 Servo saver washer (upper) * With supplied wrench, tighten servo sacer bolt completely, until it hits bottom. Do not overtighten. 9610 Servo saver bolt ! 9610 Servo saver washer (upper) Remove bolt and washer, continue assembly per instructions. 9659 Servo saver (lower) 9659 Servo saver (lower) :: Steering System (cont.
:: Steering System (cont.) 9566 Top plate 3856 x4 Steering rack bushing 9563 Front bulkhead 9659 Steering brace 9640 Steering bolt (right) ! 6925 x3 4-40 x 1/2 shcs Do not overtighten steering bolts. Make sure there is free movement in the steering rack. 9640 Steering bolt (left) 9823 SC10 chassis 6915 x2 4-40 x 5/8 fhcs :: Front Suspension 6272 Foam dust cover 9880 Steering blocks hex style (left, right) 6277 Ballstud .
:: Front Suspension (cont.) 7260 4-40 small plain nut 3983 Ballstud .30 short (black) 7922 Caster block 30˚ (left, right) 9645 2-56 x 1/8 bhcs 9622 Kingpin 6272 Foam dust cover Build left and right sides! :: Front Suspension (cont.) 9622 Outer hinge pin Build left and right sides! 9645 2-56 x 1/8 bhcs 9621 x2 Inner hinge pin 9580 Spacer 91201 Front arm (left, right) 4334 x2 2-56 x 5/16 bhcs 9564 Front hinge pin brace :: Front Suspension (cont.) 9630 x2 Ballstud washer, aluminum (.
:: Front Suspension (cont.) 6924 x4 4-40 x 3/8 shcs :: Front Suspension (cont.) 91200 SC10B front bumper (lower) 2221 x2 4-40 x 7/16 bhcs 91220 4-40 x 1 5/8 shcs 91200 SC10B skid plate 6915 x2 4-40 x 5/8 fhcs :: Front Suspension (cont.) 3.30” (83.9mm) Build left and right sides! 7230 Ball cup (large) 7253 2.62 turnbuckle 7230 Ball cup (large) Orient the notch to the left throughout the vehicle. It indicates which end of the turnbuckle has the left hand threads. ! 3.48” (88.
:: Front Suspension (cont.) 9765 x4 4-40 x 7/16 fhcs 91205 x2 SC10B roll cage bracket Build left and right sides! :: Transmission 9831 x2 3.6x0.7mm o-ring 9830 x2 Outdrive cup e as gre ck 88 5 6 # bla 9888 0.5mm gear diff shim 9828 Diff gear cover 9830 2x8mm round end pin ase gre ck 88 5 #6 bla e as gre ck bla 6588 # 9831 4.7x1.42mm o-ring Build two! :: Transmission (cont.
:: Transmission (cont.) 9829 Sun gear 9829 x4 Planet gear shims ase gre ck bla 6588 # ! 4675 x4 2.5x6mm fhcs ! Use the 1.5mm allen wrench to tighten the 2.5x6mm fhcs on the diff gear cover 9829 x4 Planet gear ase gre ck 88 5 #6 bla Align pin with groove in sun gear 9829 x2 Cross pin ! ! Align flat spots 9831 Diff gear seal ase gre ck 88 5 #6 bla ! Ensure free outdrive rotation before installation! :: Transmission (cont.
:: Transmission (cont.) 6913 x2 4-40 x 1 1/4 shcs k loc ead thr 1596 # k loc ead thr 1596 # 91203 x2 SC10B rear bumper brace (left, right) 9600 Motor plate :: Transmission (cont.) ! * Install locknut until even with end of shaft. Then tighten 3 turns for kit slipper setting. Recheck after initial run. 7485 x2 V2 slipper hub ! Compress spring ! 9654 Spur gear (87T, 48P) 7486 V2 slipper spring 9603 x2 Slipper pad 7486 V2 slipper washer :: Transmission (cont.
:: Rear Suspension 9818 Rear chassis plate 7487 Rear arm mount (3.5 degrees) 7448 x2 Rear A-arms (left, right) 7487 Anti squat shim (2 degrees) 9621 x2 Hinge pin (rear, inner) 9645 x2 2-56 x 1/8 bhcs :: Rear Suspension (cont.) 9269 x2 5-40 x 1/2 fhcs 9269 x4 5-40 x 1/2 fhcs :: Rear Suspension (cont.) 6272 x2 Dust cover foam 6277 x2 Ballstud .30 long (silver) 9643 x2 5-40 x 7/16 shcs 9630 x2 .030 alum.
:: Rear Suspension (cont.) 9644 x2 5-40 x 9/16 shcs 6927 x2 4-40 x 3/4 shcs 7260 x2 4-40 small plain nut 9824 Rear shock tower :: Rear Suspension (cont.) :: Rear Suspension (cont.
:: Rear Hubs 6272 Dust cover foam 3977 x2 Ball bearing 3/16 x 3/8 9584 Rear hub carrier (left, right) 3983 Ballstud .30 short (black) 7260 4-40 small plain nut 7369 1/16 universal roll pin 7377 Bearing spacer 7368 3/16 axle shim LEFT SIDE SHOWN 9670 Rear axle ! Build left and right sides! 9883 Wheel hex adapter :: Rear Hubs (cont.) ! Build left and right sides! 7462 Dogbone 4187 x2 Spacer 5407 x2 O-ring 9645 2-56 x 1/8 bhcs 9622 Hinge pin (rear, outer) :: Rear Hubs (cont.
:: Shocks 6469 Shock cap o-ring 9884 V2 RTR front shock body 1.02” stroke (blue) 9885 V2 RTR front shock body 1.39” stroke (blue) Remove spurs Piston 7484 Shock internal spacer Front Shock 6469 Shock cap o-ring 7484 Shock internal spacer 5407 Red o-ring 7484 Lower shock seal cap 5407 Red o-ring Piston number here Use #3 = front shocks Use #1 = rear shocks 7484 Lower shock seal cap Rear Shock :: Shocks (cont.) 6465 Shock piston #3 6459 Shock shaft 1.
:: Shocks (cont.) Step 1-3 6441 Shock cap (molded) Sh 30 ock wt flu #5 id 42 2 id k flu Shoc #5422 t 30w Step 3-4 * Shock Bleeding Steps: Step 5-6 Step 7 1. Pull shock shaft down. 2. Fill shock body 3/4 full with silicone fluid. 3. Slowly move the shock shaft up and down to remove air from under piston. 4. Wait for bubbles to come to surface. 5. Fill shock body to top with silicone fluid. 6. Place several drops of oil in the cap and on cap threads. 7. Install cap and tighten completely. 8.
:: Electronics 6272 Dust cover foam 7336 x2 Servo spacers Servo 7337 x4 Gold washer 3981 Ballstud .20 short (black) 7336 x2 Servo mount ! 9180 Servo horn Screw supplied with servo See page 40 for correct servo horn on the servo chart 6917 x4 4-40 x 3/8 bhcs ! :: Electronics (cont.) 9170 Servo link ! Leave a 1/16 gap 6292 x2 4-40 x 3/8 fhcs :: Electronics (cont.) ! Motor See page 25 for gear mesh setting instructions.
:: Electronics (cont.) 9643 5-40 x 7/16 shcs Speed Control (ESC) 9877 Receiver box (bottom) 6727 Servo tape :: Electronics (cont.) 9878 Receiver box grommet ! ! 9878 Wire grommet plug Install the ESC and servo wires into the wire grommet before installing the grommet into the receiver box! ! Receiver grommet plug can be removed if you use a personal transponder! :: Electronics (cont.
:: Electronics (cont.) 3862 5-40 x 1/8 setscrew 9879 x2 Thumb knob ! 6338 Antenna and cap 9643 x2 5-40 x 7/16 shcs ! 9877 Receiver box (top) 9879 x2 4-40 x 1/2 setscrew 9878 Receiver box seal ! Leave no gap! :: Electronics (cont.
:: Electronics (cont.) Unlocked Locked To remove your battery pack from the vehicle, twist the thumb knobs to the unlocked position, remove the battery strap, and then remove the battery. When you install the battery, make sure the thumb knobs are locked before operation. You may need to adjust the height of the thumb knobs and/or the set screws that the thumb knobs are attached to for your specific battery pack type.
:: Rollcage (cont.) 91204 SC10B roll cage hood 6925 x2 4-40 x 1/2 shcs 91204 SC10B roll cage front panel (left, right) :: Rollcage (cont.) 91204 SC10B roll cage rear body mount bar 91206 SC10B rollcage roof 6924 4-40 x 3/8 shcs 6927 4-40 x 3/4 shcs 6925 x2 4-40 x 1/2 shcs 6927 4-40 x 3/4 shcs :: Rollcage (cont.
:: Rollcage (cont.) 91214 SC10B body, clear 91213 SC10B foam body spacer ! Adhesive side down! Align holes on body panel for nerf bars! Note placement of foam spacer! :: Rollcage (cont.
:: Rollcage (cont.) ! Do not overtighten! It will deform the parts. Stop turning the screw when the gap between the parts disappears. 6292 4-40 x 3/8 fhcs 6924 4-40 x 3/8 shcs :: Rollcage (cont.) ! Do not overtighten! It will deform the parts. Stop turning the screw when the gap between the parts disappears.
:: Rollcage (cont.) 91217 SC10B cockpit underbody (clear) and helmet ! ! 9146 x4 2-56 x 3/16 bhcs Install #6936 washer onto #6924 screw as shown. Install helmet onto cockpit. ! 6936 #4 Washer aluminum ! ! 6924 4-40 x 3/8 shcs ! :: Rollcage (cont.) 6332 x2 Body clip ! ! Rollcage will clip into brackets as shown.
:: Wheels and Tires 91101 KMC hex wheel (black) Note: Clean the rims and tire bead where the two will mount to each other before you glue them together. You can clean them with either rubbing alchohol, or r/c electric motor spray. Place the foam insert inside the tire. Install the tire on the rim, and push the tire beads inside the groves on the rim. 91209 SC10B front wheel (black) Use Tire glue #1597 (not included) to glue the tire to the wheel.
:: Tuning Tips Tips for Beginners: Before making any changes to the standard setup, make sure you can get around the track without crashing. Changes to your vehicle will not be beneficial if you can’t stay on the track. Your goal is consistent laps. Once you can get around the track consistently, start tuning your vehicle. Make only ONE adjustment at a time, testing it before making another change.
:: Tuning Tips (cont.) Front Camber: Camber is the angle of the wheel when looked at from the front. The angle is measured from a line perpendicular to the ground to the face of the wheel. Camber is used to ensure a wider tire contact patch while cornering. A good starting point for the front is -1°. Performance will begin to decrease after -3°. Positive camber, where the top of the tire is leaning out, is not recommended in the front. To set your camber use the included #1719 camber gauge.
:: Shocks 5407 6299 6441 6458 6459 6465 6466 6469 6473 6475 6925 6927 7217 7484 8846 9884 9885 :: Transmission Red O-Rings 1/8” E-Clips Shock Cap, Molded Shock Shaft, 1.32“ stroke Shock Shaft, 1.02” stroke Shock Pistons, 4 each Shock Down Stops, Set Black Shock Cap O-Ring Shock Bushings Preload Spacers 5 thicknesses, Collars & Cups, 4 each 4-40 x 1/2“ SHCS 4-40 x 3/4” SHCS Shock Rod Ends / Plastic Pivot Balls V2 1/10 Shocks Rebuild Kit Preload Spacers, 4 each V2 RTR Front Shock Bodies 1.
:: Gear Differential 9827 9828 9829 9830 9831 9832 9888 Complete Gear Diff Diff Gear and Cover Gear Diff Rebuild Gear Diff Outdrives, Set Gear Diff O-Ring Set 10x16mm Bearing 0.
:: Steering 2221 3856 6272 6276 6925 9566 9610 9640 9657 9659 6 1 28 6 6 1 1 1 1 1 4-40 x 7/16” BHCS Steering Bushings, Set Foam Ball end Dust Covers Ballstud .20” Silver (short) 4-40 x 1/2” SHCS B4 / T4 Top Plate Servo Saver / Steering Hardware B4 / T4 Steering Bolt, left & right B4 / T4 HD Servo Saver Spring B4 / T4 Steering Set.
:: Front Bumper 2221 6915 91200 91220 4-40 x 7/16 BHCS 4-40 x 5/8 FHCS SC10B Front Bumper Set 4-40 x 1 5/8 SHCS 6 6 1 6 2221 2221 91200 91200 91220 91200 6915 :: Front Suspension 3977 3983 4187 4449 6272 6277 6953 7260 7368 7369 7922 9621 9622 9645 9880 9881 9882 9883 91201 3/16 x 3/8 RS Ball Bearing Ballstud .30” short (black) .030” Nylon Washers 4-40 x 3/16 Aluminum Locknut Foam Ballend Dust Covers Ballstud .
:: Battery Strap 9815 9879 SC10 Foam Battery Spacer SC10 Battery Strap, Thumb Screws, and Setscrews 1 1 9879 9879 9879 9879 9879 9815 :: Chassis / Radio Tray 3862 4334 6272 6277 6338 6915 6919 6922 6924 7487 9269 9563 9564 9630 9643 9645 9765 9818 9819 9823 9877 9878 91205 5-40 x 1/8” Set Screw 6 2-56 x 5/16” BHCS 8 Foam Ballend Dust Cover 28 Ballstud .30” Silver (long) 4 Antenna Tube (black) 1 4-40 x 5/8” FHCS 6 4-40 x 5/16” BHCS 6 4-40 x 1/2” FHCS 6 4-40 x 3/8” SHCS 6 Arm Mounts, 2.5, 3, 3.
:: Rear Shock Tower 6927 6928 7260 9643 9644 9824 91212 4-40 x 3/4” SHCS 4-40 x 1” SHCS 4-40 Plain Nut 5-40 x 7/16” SHCS 5-40 x 9/16” SHCS T4 / SC10 Rear Shock Tower SC10B Body Mounts, front & rear 6 6 12 6 6 1 1 9644 9643 7260 9643 9644 6927 7260 6927 91212 6928 9824 :: Rear Suspension 3977 3983 4187 5407 6272 6952 7260 7369 7377 7448 7462 9584 9621 9622 9645 9670 9883 Ball Bearing 3/16 x 3/8” Ballstud .30” short (black) .
:: Rear Bumper 6913 6915 6924 6932 91203 4-40 x 1 1/4” SHCS 4-40 x 5/8” FHCS 4-40 x 3/8” SHCS 4-40 x 5/16” SHCS SC10B Rear Bumper Set 6 6 6 6 1 6915 91203 6915 91203 6913 91203 91203 6924 6915 6913 6915 6924 6932 :: Wheels, Tires, Inserts 9809 89413 91101 91102 91103 91104 91105 91106 91209 91210 91211 91221 91222 SC10 Tires w/Foam Inserts 1/8 Molded Tire Inserts KMC Hex Wheels, Black (Kit) KMC Hex Wheels, Silver KMC Hex Wheels, Chrome KMC Hex Wheels/Tire Black KMC Hex Wheels/Tire Silver
:: Roll Cage 6292 6919 6924 6925 6927 9146 91204 91206 91207 91208 4-40 x 3/8” FHCS 4-40 x 5/16” BHCS 4-40 x 3/8” SHCS 4-40 x 1/2” SHCS 4-40 x 3/4” SHCS 2-56 x 3/16” BHCS SC10B Rollcage SC10B Roll cage Roof SC10B Nerf Bars, left & right SC10B Window Nets, left & right 6 6 6 6 6 6 1 1 1ea 1ea 9146 91204 91204 6927 6924 91206 6919 91204 9146 9146 91208 6927 6292 6925 91204 91204 6924 6925 91207 6927 6925 91207 6924 :: Lubes & Adhesives / Decals / Misc.
:: Factory Team and Option Parts 1283 1408 1409 1417 1585 1598 1654 1734 1735 1736 1770 1777 1778 1779 1780 1781 1787 3438 3971 6416 6417 6443 6463 6584 6906 6937 6943 7381 7416 7449 7453 7455 7476 7477 7482 7483 7495 7922 7933 7935 7990 9565 9567 9592 9596 9598 9600B 9608 9610B 9635 9665 9674 9678 9755 9789 9795 9796 9797 9798 9799 9851 9864 9865 9866 FT T4 Ti Turnbuckle Set FT Ti Turnbuckle, 2.65” (blue) for front steering FT Ti Turnbuckle, 1” (sway bar) (blue) FT Ti Turnbuckle, 2.
:: Reedy Motors and ESC’s 908 920 921 922 923 940 941 941S 942 943 944 945 946 947 948 949 950 951 952 954 955 956 957 958 987 Replacement Rotor 540-SL 540-SL Brushless Motor 3300kV 540-SL Brushless Motor 3900kV 540-SL Brushless Motor 4900kV 540-SL Brushless Motor 6100kV Sonic 540 21.5 Competition Brushless Motor Sonic 540 17.5 Competition Brushless Motor Sonic 540 17.5 Replacement Stator Sonic 540 13.5 Competition Brushless Motor Sonic 540 10.5 Competition Brushless Motor Sonic 540 9.
:: Apparel SP35** SP36** SP37** SP38** SP39** SP66** SP67** SP69** Reedy 09’ White T-Shirt (M, L, XL, 2XL, 3XL) Reedy 09’ Black T-Shirt (M, L, XL, 2XL, 3XL) Reedy 2012 T-shirt - Black (S, M, L, XL, 2XL, 3XL) Reedy Trucker Hat Reedy Patch AE Stencil Blue T-Shirt (S, M, L, XL, 2-6XL) AE Stencil Gray Sweatshirt (S, M, L, XL, 2XL, 3XL) AE 26 Time World Championship T-Shirt, Black (S, M, L, XL, 2XL, 3XL) SP70** Associated Windbreaker (S, M, L, XL, 2XL, 3XL) SP71** Associated Winter Jacket (S, M, L, XL, 2XL)
:: Tools 1111 1450 1541 1542 1543 1544 1545 1546 1547 1548 1551 1553 1554 1561 1562 1563 1564 1565 1566 1567 1589 1590 1592 1655 1656 1657 1658 1659 1660 1661 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671 1672 1673 1674 1719 1737 3718 3719 3720 3987 6429 6956 7709 FT Turnbuckle Wrench FT Ride Height Gauge FT Hex Driver Set, (7 pcs) FT .050” Silver Hex Driver FT 1/16” Black Hex Driver FT 1.5mm Purple Hex Driver FT 5/64” Blue Hex Driver FT 3/32” Gold Hex Driver FT 2.
Driver: Track: Setup Sheet Conditions: Front Suspension Team Setup Date: Event: Rev.1 Rear Suspension 3 12 1 23 Washers: Bump steer 2 spacer: 1 Anti Roll Bar: Black (soft) Silver (med) Gold (hard) None 1 Washers: 12 Rear Hub Carriers Plastic ABC IO Ackerman: AB C -1 Toe: 0° Ride Height: Caster: Anti-Squat: 20˚ 25˚ 30˚ Camber: 31mm Front Shocks Gold 3.
:: Hardware - 1:1 Scale View Socket Head (shcs) Flat Head (fhcs) Button Head (bhcs) 4-40 x 1/4 (6285) 4-40 x 3/8 (6292) 2-56 x 1/8 (9645) 4-40 x 5/16 (6932) 4-40 x 7/16 (9765) 2-56 x 3/16 (9146) 4-40 x 3/8 (6924) 4-40 x 1/2 (6922) 2-56 x 5/16 (4334) 4-40 x 1/2 (6925) 4-40 x 5/8 (6915) 4-40 x 5/16 (6919) 4-40 x 5/8 (6926) 5-40 x 1/2 (9269) 4-40 x 3/8 (6917) 4-40 x 3/4 (6927) 4-40 x 7/8 (7738) 4-40 x 7/16 (2221) Shims and Washers 3x6mm (31531) 4-40 x 1 (6928) .
Driver: Track: Setup Sheet Conditions: Front Suspension Date: Event: Rev.1 Rear Suspension 3 12 1 23 Washers: Bump steer spacer: Anti Roll Bar: Black (soft) Silver (med) Gold (hard) None Washers: 12 Rear Hub Carriers Plastic ABC IO Ackerman: IO AB C Front Back Camber: Toe: 2 1 Caster: Anti-Squat: 20˚ 25˚ 30˚ Camber: Aluminum Tower: A BCD Hub Toe: std 0° 0.5° 1° 1.
Associated Electrics, Inc. 26021 Commercentre Dr. Lake Forest, CA 92630 USA http://www.TeamAssociated.com http://www.RC10.com http://twitter/Team_Associated http://bit.ly/AEonFacebook call: (949) 544-7500 - fax: (949) 544-7501 Check out the following web sites for all of our kits, current products, new releases, setup help, tips, and racing info! www.TeamAssociated.com. - www.RC10.