EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
EN Contents • 1/10-Scale Ready To Compete 22SCT • Spektrum™ DX2L 2.4GHz DSM® Radio System (SPMR2400) • Spektrum SR3520 DSM2® 3-Channel Micro Race Receiver (SPMSR3520) • Dynamite® Platinum Sensored Brushless ESC, 13.5T Limit (DYNP1001) • Dynamite Platinum 17.5T Sensored Brushless Motor (DYNP1017) • Extra High-Torque Servo (LOSB0812) • 4 AA batteries (for transmitter) Tools Included Needed to Complete • 4-Way wrench • 7.
EN Spektrum Dx2L Transmitter 11 19 12 13 14 15 18 1. Steering Wheel controls direction (left/right) of the model 2. Throttle Trigger controls speed and direction (forward/brake/reverse) of the model 3. R.O.S.S. Button used with vehicles featuring the R.O.S.S. Remote Start System 4. Antenna transmits the signal to the model ST N 5. ON/OFF Switch turns the power ON/OFF for the transmitter TH LIMIT TH R N R L 150% 6.
EN ADJUSTING THE STEERING TRIM ADJUSTING THE THROTTLE Trim The steering trim dial is used to adjust the steering trim when the wheel is centered. Rotating the dial changes the steering trim (the steering at rest position). Normally, the steering trim is adjusted until the vehicle tracks straight. The throttle trim dial adjusts the throttle trim when the throttle trigger is at neutral (center).
EN Control Test Forward Brake/Reverse Perform a control test with the vehicle wheels off of the ground. If the tires rotate after the vehicle is powered-on, adjust the “TH. Trim” knob located to the lower left of the steering wheel until they stop. To make the wheels move forward, pull the trigger. To reverse the wheels, wait for the model to stop, then push the trigger. When moving forward, the wheels should track in a straight line without any steering wheel input. If not, adjust the “ST.
EN Recalibrating and Adjusting the ESC (DYNP1001) 4. The red LED flashes when you enter a menu. The number of flashes corresponds to the current selection. 5. Quickly press the Setup button to change the menu option. 6. After you select a menu option, press and hold the Setup button to confirm the selection. The black-shaded setting is the factory default.
EN Changing between Blinky and Timing Modes Precautions • Never touch moving parts. • Always remove the battery pack before performing any maintenance on the vehicle. • Always let parts cool before touching. Adjusting the Slipper Turn the 5.0mm adjustment nut clockwise (to the right) to reduce the slip or counterclockwise (to the left) to increase the slip. Setting the Gear Mesh The gear mesh has already been set at the factory. Setting it is only necessary when changing motors or gears.
To change to the Timing Mode 15° Motor Timing 1. Remove the body from the vehicle. 2. Use the 2mm Hex Wrench (“L” shaped) to loosen the 3 motor end plate screws 2 turns each. 3. Rotate the motor end plate clockwise until the line on the end plate is matched to the 2nd line on the “-” side from the longer center mark. 30° 25° (centerline) 4. Use the 2mm Hex Wrench (“L”-shaped) to tighten the 3 motor end plate screws.
EN Limited Warranty WARRANTY SERVICES What this Warranty Covers Questions, Assistance, and Repairs Horizon Hobby, Inc. (“Horizon”) warrants to the original purchaser that the product purchased (the "Product") will be free from defects in materials and workmanship at the date of purchase. Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly.
EN Warranty and Service Contact Information Country of Purchase Horizon Hobby Address Phone Number / Email Address United States of America Horizon Service Center (Electronics and engines) 4105 Fieldstone Rd Champaign, Illinois, 61822 USA 877-504-0233 Online Repair Request: www.horizonhobby.com/service Horizon Product Support (All other products) 4105 Fieldstone Rd Champaign, Illinois, 61822 USA 877-504-0233 productsupport@horizonhobby.
EN Compliance Information for the European Union Declaration of Conformity (in accordance with ISO/IEC 17050-1) No. HH2013021501 Product(s): TLR 22SCT RTC (includes Spektrum DX2L Transmitter with Spektrum SR3520 Receiver) Item Number(s): TLR03001 Equipment Class: 2 The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC and EMC Directive 2004/108/EC: EN 300-328 V1.7.