Installation Instructions

Physical Properties
Description
Base Acrylic Latex
Physical State Paste
Color White
Odor Nil
Open Time [at 72°F (22°C)] 20 to 35 minutes
Wt./U.S. Gallon 12.5 lbs. ± .2 lbs .
VOC/Liter of Material 0 g/L
Foot Traffic Rating (ASTM C627) Residential to light commercial
Storage
Store in cool, dry location. Do not store open
containers. Freeze/thaw stable.
Shelf Life
Maximum 1 year from date of manufacture in
properly stored, unopened package. Good for 6
months if tightly re-sealed, stored in a cool, dry
location and used within shelf life.
5. INSTALLATION INSTRUCTIONS
Surface Preparation
All surfaces must be clean, dry, free of dirt, dust, grease, oil, loose paint, wallpaper,
and residues of old adhesive, or any foreign matter which might impair adhesion
where TEC
®
Type 1 Mastic is spread. Painted enameled walls and floors must be
thoroughly scored or sanded to insure a bond to the original base wall or floor.
Do not sand any floors or adhesives that are known or suspected to contain
asbestos. Installations where concrete is damp or the concrete is subject
to moisture vapor emissions can fail.
Application
The adhesive, tile, and room should be maintained at a minimum temperature of
60ºF for 24 hours prior to installation. The minimum 60ºF temperature must be
maintained during the entire installation, and for a minimum of 48 hours following.
Use a
3
⁄
16
" x
5
⁄
32
" V-notched trowel for installation of tile up to 6" x 6". For tiles
larger than 6" x 6", use a
1
⁄
4
" x
1
⁄
4
" x
1
⁄
4
" square-notched trowel. Maximum tile
size: for walls is 12" x 12"; for floors is 8" x 8".
Only apply the amount of adhesive to surface that can be tiled over in 15 minutes.
DO NOT SET TILE IF SKIN HAS FORMED ON THE ADHESIVE. If adhesive skin has
formed, remove and reapply. This time will vary with the temperature, humidity,
and the substrate. Apply the adhesive to the substrate first with the flat side of
the trowel. Then comb with the notched side of the trowel in one direction. Firmly
press tiles into the adhesive and move them perpendicularly across the ridges. Do
not slide tiles against each other. Periodically remove and check a tile to assure
complete coverage.
Cure times will vary with size and porosity of tile and porosity of floor (porcelain
tiles take considerably longer to cure), humidity and temperature (cooler
temperatures will extend set times). Typical floor installations take longer to cure.
No traffic is permitted on tiles prior to curing. Grouting may begin once adhesive
is firmly set up. Up to 6" x 6" wall tiles require wait time of 6 hours or longer.
Over 6" x 6" tile or any floor tile application requires at least 24-48 hours. Check
to determine readiness by trying to twist the tile and see if it moves. If it does,
additional cure time is required. If the tile won’t twist but you hear a wet suction
sound when the tile is stepped on, additional cure time is also required. The use
of TEC
®
brand grouts is highly recommended.
Full cure takes at least 48-72 hours depending on conditions. The finished
installation must be protected from freezing until completely cured.
For glass tile, refer to manufacturer's specifications. For marble and granite
installations, test in an inconspicuous area as discoloration may occur. Most
discoloration disappears after 30 days. For proper curing, do not abut marble tiles
together.
Clean-up
While adhesive is still fresh, clean tools, hands, and excess materials from face of
tile with warm soapy water.
6. AVAILABILITY
TEC
®
Premium Tile and Stone Installation Products are available nationwide.
To locate TEC
®
products in your area, please contact:
Phone: [phone]
Website: tecspecialty.com
7. WARRANTY
For warranty details, see your sales associate or tecspecialty.com.
8. MAINTENANCE
Not applicable
9. TECHNICAL SERVICES
Technical assistance
Information is available by calling the Technical Support Hotline.
Toll Free: 800-832-9023
Fax: [phone]
Technical and safety literature
To acquire technical and safety literature, please
visit our website at tecspecialty.com.
10. FILING SYSTEM
Division 9
TEC
®
Type 1 Mastic Product Data
©Copyright 2013 H.B. Fuller Construction Products Inc.
TEC
®
is a trademark of H.B. Fuller Construction Products Inc. DST1M R1213-1
tecspecialty.com
H.B. Fuller Construction Products Inc.
1105 South Frontenac Street
Aurora, IL 60504-6451