Installation Sheet

ManualsBrandsTech Lighting ManualsShop All Tech LightingTech Lighting Voto 18" Tall LED Outdoor Path Light - Low Voltage

Installation Instructions for

Voto Pathway

920OAVOTO

GP I :ENERAL RODUCT NFORMATION

This product is suitable for wet locations.

12VAC input only.

If using Tech Lighting magnetic transformers, this product be

dimmed with a low-votage magnetic dimmer. For all other

transformers, consult with the manufacturer for compatible

dimmers.

CAUTION RISK OF FIRE-

This product must be installed in accordance with the applicable

installation code by a person familiar with the construction and

operation of the product and the hazards involved.

Use minimum 90°c supply conductors.

OUTDOOR

Loosen the four set screws on fixture(Do Not Remove)

base with the provided Allen wrench and remove the

base plate.

Prepare the Fixture

700OAVOT_

1.1

Attach the stake to the base plate by tightly screwing

down the provided stake bolt through the center hole

of the base plate and the stake.

Reattach the base plate assembly to fixture and tighten

down the set screws on the canopy (reversal of Section

1A).

STAKE

STAKE BOLT

BASE PLATE

Install the Fixture using a Stake

(with canopy)

Determine the method of installation:

 Install the fixture using a stake , go towith a canopy

Section 2.

 Install the fixture using a stake , gowithout a canopy

to Section 3.

 Install the fixture , go to Section 4.without a stake

WARNING – Risk of Electric Shock. Install all luminaires

10 feet (3.05 m) or more from a pool, spa, or fountain.

Unit low voltage cable is to:

a) be protected by routing in close proximity to the

luminaire or fitting, or next to a building structure such

as a house or deck;

b) not be buried except for a maximum 6 inches (15.2

cm) in order to connect to the main low voltage cable;

and

c) have the length cut off so that it is connected to a

connector within 6 inches (15.2 cm) from a building

structure, a luminaire, or fitting.

ALLEN

WRENCH

BASE PLATE

SET SCREW

Summary of content (4 pages)

PAGE 1
920OAVOTO Installation Instructions for Voto Pathway 700OAVOT_ 1.1 OUTDOOR GENERAL PRODUCT INFORMATION: This product is suitable for wet locations. 12VAC input only. If using Tech Lighting magnetic transformers, this product be dimmed with a low-votage magnetic dimmer. For all other transformers, consult with the manufacturer for compatible dimmers. WARNING – Risk of Electric Shock. Install all luminaires 10 feet (3.05 m) or more from a pool, spa, or fountain.
PAGE 2
B 3B 5 STEM SET SCREW 3 BUSHING 4 5 6 STAKE 3 3 Bring the power wires to the fixture location in accordance with local electrical codes. 4 Connect the white fixture wire to one of the lowvoltage power line wire with the provided outdoor waterproof wire nut. 5 Connect the black fixture wire to the remaining lowvoltage power line wire with the provided outdoor waterproof wire nut. 3 Feed the fixture cord through the bushing and screw the bushing onto the stem.
PAGE 3
4C 3D 4 3 Connect the white driver wire to one of the low-voltage power line wire with a wire nut. 4 Connect the black fixture wire to the remaining lowvoltage power line with a wire nut. Stake the fixture to the desired location and properly bury the wire and wire nut connections. 5 3 4D Install the Fixture to Concrete (or other hard surfaces) 4A FIXTURE SET SCREW BASE PLATE 5 5 ALLEN WRENCH BASE PLATE 1 5 0.
PAGE 4
RECTANGULAR MOUNTING PLATE TEMPLATE WARNING: If printing this template, ensure printer settings are set to actual size. 7400 Linder Ave, Skokie, IL 60077 847.410.4400 www.techlighting.com SAVE THESE INSTRUCTIONS! © 2018 Tech Lighting, L.L.C. All rights reserved. The "Tech Lighting" graphic is a registered trademark of Tech Lighting, L.L.C. Tech Lighting reserves the right to change specifications for product improvements without notification.