Sensorkit X40 You can find code-examples and software on our website www.joy-it.
Dear customer, thank you for purchasing our product. Please find our instructions below: Pin-Assignment The pin-assignment is also shown in the description of the sensors. Please find the used numbering on the left side. It is marked that the contact-pins are pointing away, to the right, from the board. We recommend to use Dupontcables to connect the sensors to a breadboard or directly to the experimental board.
KY-001 Temperature Sensor Module Chipset: DS18B20 | Communicationprotocoll: 1-Wire 9 - 12Bit exact temperature measurement in measurementrange from –55°C to +125°C KY-002 Shock-Switch Module The contact between the two input pins is connected when a shock is detected KY-003 Hall Magnetic-Field-Sensor Module Chipset A3141 Sensortype: Hall Effect Transistor/Switch The transistor connects when the module is near by a magnetic field. This can be measured as an analog value at the signal output.
KY-006 Passive Piezo-Buzzer Module Controlled with PWM-signals in different frequencies, different sounds can be produced. ① - GND ② - +V ③ - Signal KY-009 RGB LED SMD Module LED-Module which contains a red, blue and green LED. These are connected with a common cold cathode. ① - GND ② - LED Green ③ - LED Red ④ - LED Blue Depending on the input voltage, a resistor is necessary KY-010 Light-barrier-Module The connection between to input pins is interrupted if the light-barrier is interrupted.
KY-013 Temperature-Sensor Module Temperature measuring range: -55°C / +125°C This module contains a NTC Thermistor—this has a declining resistor-value when the temperature is rising. KY-015 Combination-Sensor Temperature+Humidity Chipset: DHT11 | Communicationprotocoll: 1-Wire Measuring range humidity: 20-90%RH Measuring range temperature: 0-50°C KY-016 RGB 5mm LED Module LED-Module which contains a red, blue and green LED which are connected with a common cathode.
KY-019 5V Relais Module Voltage range: 240VAC / 10A | 28VDC / 10A A relais to toggle higher voltages with a 5V output. Security information: VDC =< 30V Higher voltages can result in extremely dangerous injuries. KY-020 Tilt-Switch-Module Depending on the tilt, a switch connects the input pins.
KY-024 Linear magnetic Hall Sensor Chipset: A3141 | OP-Amplifier: LM393 The magnetic field is measured by the sensor and transferred as an analog voltage. The sensitivity of the sensor can be adjusted with the potentiometer. Digital Output: If a flame is detected, a signal is given here Analog Output: Direct measured value of the sensor unit KY-025 Reed Module If a magnetic field is detected, its given out to the digital output.
KY-029 2-color [Red+Green] 3mm LED Module LED-Module which contains a red and a green LED. These are connected with a common cathode. Depending on the input voltage, a resistor can be necessary ① - LED Gren ② - LED Red ③ - GND If the sensor is exposed to a knock/shock, both output pins are connected. ① - GND ② - +V ③ - Signal KY-032 Obstacle Detection Module If the emitted infared light hits an obstacle, the light is being reflected and detected by the photodiode.
KY-035 Bihor Magnet Sensor Module Chipset: AH49E The sensor gives an analog voltage to its output which shows the intensitiy of a magnetic field. ① - Signal ② - +V ③ - GND KY-036 Metal-Touchsensor Module ① - digital signal ② - +V ③ - GND ④ - analog signal Gives out a signal if the front metal tip is touched. The sensitivity can be controlled with the controller.
KY-040 Rotary Encoder The current position of the rotary switch is given out coded on the output. KY-050 Ultrasonic-Distancesensor ① - [CLK] ② - [DT] ③ - Button ④ - +V ① - GND ② - Echo ③ - Trigger Measurement-resolution: 3mm ④ - +V If a signal (falling peak) is given to the trigger-input, a distance measurement is executed and given out as a PWM-TTL signal to the echo-output.
Software und Codexamples On our website www.joy-it.net/sensorkit/ we offer a collection of code-examples for e.g. the Arduino and the Raspberry Pi. For some modules (e.g. the analog-digital-converter) you need an additional software to read the measurement results. You can find these also on our website. Voltage Level Depending on the experimentalboard/microconrollersystem you use, different voltagelevels can occur.
You can find more supplies for Raspberry Pi and Arduino on our website: www.joy-it.net Recommenda- 3.2“ TFT Touchscreen Display StromPi V2 Resolution 320x240 Interface SPI Widerange power supply with USV-function for Raspberry PI and other computers with USB power supply Can be plugged directly to the Raspberry PI 6-61V DC voltage input Output: 5V @3A Joy-IT® is a trademark of Simac Electronics Handel GmbH | Pascalstr.
