MODEL RTA-8409 ASSEMBLY INSTRUCTIONS Thank you for purchasing one of our products. Please read carefully the assembly instructions before the installation. Do not discard this manual or any of the packaging material until the unit has been completely assembled.
RTA-8409 P.2 P.
RTA-8409 P.3 P.3 MAIN PARTS LIST Drawer right panel Drawer back panel Drawer bottom panel Right back panel HARDWARE LIST: Parts 1-13 come together; parts 14 come separate. Part No. Figure Description Qty 1 8x25mm wooden pins (dowels) 40 2 15mm cam locks and bolts 3 M5x40mm screws 19 4 M4x38mm screws 4 5 M3.5x16mm screws 4 6 M5x8mm euro screws 4 7 Handle “L” shape (84mm) and 2 of M3.
RTA-8409 P.4 P.4 BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS. • Do a quick inventory to make sure the product contains all the parts and hardware. • Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the CONTACT card included with the product. • The replacement parts service is limited to the continental United States. If you reside in Hawaii, Puerto Rico, U.S.
RTA-8409 P.5 P.5 ASSEMBLY STEPS STEP 1 Hardware: 1 8x25mm x40 Install the bolts (2) into the panels (E), (F) and (N) in the holes shown in the illustrations. Please pay attention to the correct holes to use as other holes on the panels are intended for other hardware in other steps. After done, set the panels aside to use on future steps.
RTA-8409 P.6 P.6 STEP 3 Grab the set of sliders (14) and separate the pieces According to their shape: - The “flat” ones will be used on the next step. - The “L” shaped will be used until step 19, so please set them aside. Assemble the flat sliders (14) to the top set of holes on the right panel (H) and the middle panel (I) using screws (6) as shown. Note that the wheel is facing towards the front of the panels and down with 2 empty holes (on the slider) above it.
RTA-8409 P.7 STEP 7 Hardware: 3 M5x40mm 10 Screw cap x2 Assemble the hutch right panel (C) to the hutch panels (A) and (E) using screws (3), and cover the screws with (10) as shown. x2 P.7 STEP 8 Hardware: 2 15mm 9 15mm x1 Insert and align the cam lock (2) into the hutch middle panel (D), and assemble to panel (E) as shown and explained in page 4, then cover the cam lock with (9).
RTA-8409 P.8 Assemble the middle panel (I) to the back panel (M) using screws (3) as shown. STEP 11 M5x40mm (Top) Hardware: 3 P.8 x2 (Top) (Panel I shown from its right side with its back edge facing down) (Same parts as step 10, but shown from the right) Assemble the bottom panel (J) to panel (I) using screws (3), and cover the screws with (10). Then install the foot panels (L) to the panel (I) as shown (they only connect with the wooden pins).
RTA-8409 P.9 STEP 14 overHardware: the frame, 15mm 9 15mm x6 x2 First insert and align the cam locks (2) in the panels (G), (H) and (I). Then, and with the help of another person, carefully place the top parts assembled in step 9 making sure the bolts and wooden pins from the main panel (F) properly enter into the corresponding holes on panels (G), (H) and (I). Then secure the main panel (F) by turning the cam locks as shown and explained in page 4.
P.10 Insert and secure the corner brackets (12) on the 2 back corners of the unit using screws (13) as shown. STEP 16 Hardware: 12 C. Bracket 13 M3x16 P.10 RTA-8409 x2 x4 (Same parts as step 15, but shown from behind) STEP 17 First insert and align the cam locks (2) into the drawer side Hardware: panels (O) and (P), and then assemble them to the drawer 15mm x2 2 front panel (N) as shown and as explained in page 4. Then slide the drawer bottom panel (R) thru the groves of the 3 panels as shown.
P.11 With the drawer upside-down and its front facing away from you, assemble the “L” shaped sliders (14) using screws (5) as shown. STEP 19 Hardware: 5 M3.5x16m x4 ATTENTION: VERY IMPORTANT! Hardware: Handle x1 7 M3.6x24mm 9 15mm x2 x2 (Same parts as step 19, but shown flipped upright with front panel facing away) Install the metal pins (8) in the desired sets of holes inside the unit, and place the adjustable panel (K), and then insert the drawer as shown.
P.12 P.12 RTA-8409 AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING CARE AND MAINTENANCE WARNINGS: WEIGHT LIMITS 11 Lbs. (5 Kg) 110 Lbs. (50 Kg) 11 Lbs. (5 Kg) 22 Lbs. (10 Kg) 22 Lbs. (10 Kg) • Do not exceed the indicated weight limits. • Do not expose the surfaces to direct sunlight or to extreme environmental conditions. • Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry with a clean towel.
