ASSEMBLY INSTRUCTIONS Thanks for purchasing one of our products. Please read carefully the assembly instructions before the installation. Do not discard this manual or any of the packaging material until the unit has been completely assembled.
▪ A B ▪ ▪ E ▪ F ▪ I ▪ ▪ ▪ ▪ Left Shelf panel Q ▪ Drawer Front G U ▪ L ▪ O P ▪ Door ▪ Shelf Back S ▪ V H K R ▪ ▪ ▪ ▪ N D ▪ ▪ J M ▪ C T ▪
▪MAIN I M L O L N K J A B H V D C R F Q E G P U T S
▪ PART QTY. ITEM 11 9Pcs 1 2Pcs Long Wooden Pin 12 1Pcs 2 48Pcs Short Wooden Pin 13 1Set 3 10Sets Cam Lock & Bolt Sets 14 1Set 4 4Pcs Screw - 5 x 8mm 15 2Sets (Euro Screw) 5 8Pcs Screw TP 10#x1/2'' 6 4Pcs Screw - 3 x 16mm 7 6Pcs Screw - 3.5 x 16mm 8 4Pcs Screw - 4 x 38mm 9 17Pcs Screw - 5 x 40mm 10 4Pcs Cam lock Caps Screw Caps Cable Management (Grommet) Handle L Shape (84mm) M3.5x15mm Screw Handle L Shape (84mm) M3.
1 O I 2 L L 2 K J M N H B D F C R S E - Install 48pcs of small Wooden Pins (2) into all panels as shown. Use a wooden or light rubber hammer to avoid damage to the pins. Please pay close attention to which holes you have to use, and do not join any parts yet! 2 3 G 3 Q A - Attach all the bolts (3) to panels (A), (G) & (Q) as shown above. Please make sure to attach them to the correct holes as some holes are intended for different hardware in subsequent steps.
3 "L" Shaped Flat Shaped Separate the 4 pieces of the sliders (19) according to their shape: - The flat shaped will be used in the next step (2 pieces, both left and right). - The “L” shaped will be used until step 23 (2 pieces, left and right). 4 4 19 ) p (To (Fro nt) - Install the flat shaped sliders (19) on panels (C) and (D) using screws (4) as shown.
5 6 3 3 7 3 7 16 16 G H E - Attach L Bracket (16) to the top edge of panel (H) using screw (7) as shown. 7 9 ) op 9 (T (Fro nt) 11 B 11 - Assemble panels (B) and (H) using screws (9) as shown.
The panels from previous step are shown here from the right side 8 9 nt) (Fro (T 9 op ) H D - Assemble the panel (D) to the panel (H) using screws (9) as shown. 9 The panels from previous step are shown here from the left side 9 9 11 F 11 D E - First assemble the panel (E) to panel (D) using screws (9) and attach the plastic caps (11) as shown. Then install the panel (F) to panel (D) by just pushing the wooden pins into the holes.
The panels from previous step are shown here from the right side B D 9 11 C E 18 9 18 11 - First assemble the panel (C) to the panel (E) using screws (9), and attach the plastic caps (11) to panel (C), then install the plastic feet (18)to the bottom of panels (B), (D) and (C) as shown. 11 The panels from previous step are shown here in normal upright position V D C - Insert the back panel (V) into the groves of the panels (C) and (D) as shown.
13 12 1 1 N M K M - Install 2 pcs of Long Wooden Pins (1) into panel (M) as shown. Use a wooden or light rubber hammer to avoid damage to the pins. - Assemble the panel (M),(N) to the panel (K) as shown. 14 15 K M L L - Assemble the panel (L) to the panel (M) as shown. O - Assemble the panel (O) to the panel (K) as shown.
16 The panels from previous step are shown here in normal upright position 9 9 O I ▪ Assemble the panel (I) to the panel (O) using screws (9) as shown. 17 9 The panels from previous step are shown here from the back 9 11 I K 11 O J ▪ Using screws (9), assemble panel (J) to panel (O), and then panel (O) to panel (K) and attach the plastic caps (11) to panel (J), (O) and (I) as shown.
18 (Fro Main panel (A) shown from the underside The panels from previous step are shown here laying down showing the underside nt) t) igh (R - First install the grommet (12) into the hole of panel (O) from the inside, then assemble the main panel (A) to panels (I), (J) and (O) using screws (9) as shown. 19 A B H D 3 C 10 - First install and align the cam locks (3) into panels (B), (C), (D) and (H), and assemble the main panel (A) as shown and as explained in page 4.
20 The unit is shown from the back 17 6 6 17 - On the back of the unit, install the corner Z brackets (17) to the top left corner and bottom right corner using screws (6) as shown. 21 22 3 8 8 U T R S Q - Using cam locks (3), and as shown and explained in page 4, assemble drawer side panels (S) and (R) to the drawer front panel (Q). Then slide the bottom panel (U) thru the groves on all panels as shown. - Assemble the drawer back panel (T) to the drawer side panels using screws (8) as shown.
24 23 10 13 7 13 10 13 7 19 7 - Place the drawer upside-down and assemble the “L” shaped sliders to the bottom using screws (7) as shown. Please note that the wheels go towards the back of the drawer and the sliders should not protrude from the bottom, otherwise the drawers raise 3/4” and will not fit in the unit. - First install the handle (13) to the drawer front panel (Q) using the own handle screws, then install the cam locks caps (10) as shown.
26 5 5 C 15 P Assemble the door (P) to the left panel (C) using screws (5), and adjust the alignment if necessary: (A): This screw adjusts the door up and down. (B): This screw adjusts the door side to side. (C): This screw adjusts the door's depth. DONE! Before you start using, please read all the warnings in the next page.
5Kg (11 Lbs) 50Kg (110 Lbs) 5Kg (11 Lbs) 5Kg (11 Lbs) 4.5Kg (10 Lbs) Do not exceed the weight limits. Do not expose the surfaces to direct sunlight or to extreme environmental conditions. Clean the surfaces preferable with a soft cloth damped with a solution of mild soap and water, then dry with a clean towel. If you decide to apply a cleaning agent, first test on a small area of the unit that is hidden from view, for example, under the table top. Do not sit on the tabletop.
