MODEL RTA-980FBC ASSEMBLY INSTRUCTIONS Thank you for purchasing our product.
P. 1 RTA-980FBC • Please read carefully the assembly instructions before the installation. • Do not discard this manual or any of the packaging material until the unit has been completely assembled. • Might require two people. P.
P. 2 P. 2 RTA-980FBC MAIN PARTS LIST 1 2 Shelf x2 Metalic Support x2 MAIN PARTS LAYOUT (FOR REFERENCE) 1 2 2 1 LIST OF INCLUDED HARDWARE TOOLS YOU WILL NEED (NOT INCLUDED) PART QTY ITEM A 16 4x14 B 4 6x35 Pencil C 4 4,5x60 Leveler Screwdriver Hammer Measuring tape Drilling machine NOTE: You will need screwdriver, hammer, pencil, leveler, measuring tape and drilling machine (not included) to assemble the products.
P. 3 RTA-980FBC P. 3 BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS. Do a quick inventory to make sure the package contains all the parts and hardware listed in the assembly instructions. To avoid misalignments, always leave the screws loose and tighten them until all pieces are positioned correctly. Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the last pages on this manual.
P. 4 P. 4 RTA-980FBC ASSEMBLY STEPS STEP 1 Place one of the shelves 1 over the brackets of the metallic supports 2. The surface with the pre-drilled holes go facing down and they should align with the brackets. (Front) Pre-drilled holes 1 2 Make sure these holes on 2 are oriented on the same side towards the back. (Top) 2 (Back) (Bottom) STEP 2 Hardware/Tools A Use a screwdriver (not included) to secure the shelf 1 to the supports 2 with screws A as shown.
P. 5 P. 5 RTA-980FBC STEP 3 Place the second shelf 1 over the brackets of the metallic supports 2. The surface with the pre-drilled holes go facing down and they should align with the brackets. (Top) (Front) (Bottom) 1 (Back) Pre-drilled holes STEP 4 Hardware/Tools A Use a screwdriver (not included) to secure the shelf 1 to the supports 2 with screws A as shown. 8 4x14 pcs NOT INCLUDED 1 A A Tip If desired, after assembly use an alcohol cleaner to erase the number printed on the parts.
P. 6 STEP 5 Hardware/Tools B 4 6x35 P. 6 RTA-980FBC pcs NOT INCLUDED: IMPORTANT: The measurements given here should make the holes on the wall coincide with the holes on the metallic supports, however, there is always a small chance that they might not exactly coincide by mere millimeters. You should always check and compare the measurements on the supports against the markings on the wall before drilling any holes. Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Select the height you want to fix the product on your wall.
P. 7 RTA-980FBC STEP 6 Hardware/Tools C With the help of another person holding the unit, use a screwdriver (not included) to secure the unit to the anchors on the wall with screws C as shown. 4 4,5x60 P.
P. 8 RTA-980FBC ALL DONE! Give yourself a nice pat on the back. You did a great job! P.
P. 9 P. 9 RTA-980FBC CARE, MAINTENANCE AND SAFETY WARNINGS: WEIGHT LIMITS A A A = 11 Lbs. (5 Kg ) Ÿ Do not exceed the indicated weight limits. Ÿ Do not expose the surfaces to direct sunlight or to extreme environmental conditions. Ÿ Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ then dry with a clean towel. Do not use solvents or abrasive materials to clean the unit.
P. 10 RTA-980FBC P. 10 TECHNI MOBILI DESK WARRANTY DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY RTA Products, LLC warrants to the Original Purchaser who acquired a new product from RTA Products or its authorized resellers that this product will be free from defects in its workmanship and materials, under normal use and service conditions, as described herein. "Defects" as used in this warranty, is defined as any imperfections that impair the use of the furniture or product.
11 11 FOR SEVERAL HELP OPTIONS INCLUDING REPLACEMENT PARTS ORDERS _________________________________________________________________ VISIT: WWW.TECHNIMOBILI.COM CLICK ON SUPPORT TAB Scan QR Code to order replacement parts OR EMAIL US: SUPPORT@RTAPRODUCTS.
