02'(/ 57$ % $66(0%/< ,16758&7,216 7KDQN \RX IRU SXUFKDVLQJ RXU SURGXFWV 6FDQ 45 &RGH WR YLHZ IXOO DVVHPEO\ YLGHR
3 57$ % 3OHDVH UHDG FDUHIXOO\ WKH DVVHPEO\ LQVtUXFWLRQV EHIRUH WKH LQVWDOODWLRQ 'R QRW GLVFDUG WKLV PDQXDO RU DQ\ RI WKH SDFNDJLQJ PDWHULDO XQWLO WKH XQLW KDV EHHQ FRPSOHWHO\ DVVHPEOHG 6FDQ 45 &RGH WR YLHZ IXOO DVVHPEO\ DQG VWHS YLGHR 3
57$ % 3 3 MAIN PARTS LIST Left panel [ Right panel [ Casters [4 Back panel [ Front panel [ Mid panel [ Bottom panel [ Top panel [ Lateral structure [ Top structure [ Plastic cover [ Main panel [ Right tilting [ mechanisim Left tilting [ mechanisim Protection rail [ Screw Knob [ A: Magnetic Catch [ B: Steel Plate Drawer panel [ Handle [
57$ % 3 3 SCREWS LIST: MAIN PARTS LAYOUT (FOR REFERENCE): 15 12 13 14 16 10 10 11 8 18 9 1 2 7 5 ֊ This unit uses cam bolts and locks. The following explains how to use them. This is not an assembly step; it is a guide for when you are actually doing the assembly using this kind of hardware. Cam Bolt 1. Screw the bolt into the corresponding panel. Cam Lock 2.
3 57$ % 3 BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS. ❶ Do a quick inventory to make sure the package contains all the parts and hardware listed in the assembly instructions. ❼ To avoid misalignments, always leave the screws loose and tighten them until all pieces are positioned correctly. ❷ Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the CONTACT card included with the product.
57$ % 3 5 3 5 ASSEMBLY STEPS Use Screws ( F ) to fix the Magnetic Catch ( 17A ) to the inside face of Top Panel ( 8 ). Use Screws ( F ) to fix the Steel Plate ( 17B ) to the Drawer Panel ( 18 ).
57$ % 3 6 STEP Screws: ' 6x40mm + 5x17mm x4 3 6 First screw the Bolts ( D ) to the inside face of the Right Panel ( 2 ). Then insert the other metal Pin ( H ) into the hole of Drawer Panel (18 ). Finally place down the panel ( 2 ) and assemble it to panels ( 1 ), ( 4 ) and ( 5 ) by turning the cam locks on those panels as shown and as explained in page 3.
57$ % 3 7 STEP Screws: ' 6x40mm x6 3 7 First screw the bolts ( D ) to the top panel ( 8 ), then place it down and assemble it to the structure by turning the cam locks on panel ( 1 ), ( 2 ) and ( 4) as shown and as explained in page 3. 8 4 6FDQ 45 &RGH WR YLHZ WKLV VWHS STEP Use screws ( C ) to fix the Lateral structure ( 9 ) to left and right panels ( 1 ), ( 2 ) and to the bottom panels ( 7 ).
57$ % 3 8 STEP Use Screws ( E ) to fix the Left & Right Tilting Mechanisms ( 13 ) and ( 14 ) to the Main Panel ( 12 ) on the corresponding sides. Note that the pieces are shown below upside-down.
57$ % 3 9 3 9 Use Screws ( B ) to fix the Protection Rail ( 15 ) to the Main Panel ( 12 ). STEP Screws: % 15 5X16mm x3 12 6FDQ 45 &RGH WR YLHZ WKLV VWHS Use Screw ( G ) to fix the Handle ( 19 ) to the Drawer Panel ( 18 ).
57$ % 3 0 ALL '21( *LYH \RXUVHOI D QLFH SDW RQ WKH EDFN
57$ % 3 1 3 1 AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING WARNINGS FOR CARE AND MAINTENANCE: t /',d >/D/d^ ϮϬ >ďƐ͘ ϮϬ >ďƐ͘ ϭϱ >ďƐ͘ ϮϬ >ďƐ͘ Do not exceed the indicated weight limits. Do not expose the surfaces to direct sunlight or to extreme environmental conditions. Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry with a clean towel. Do not use solvents or abrasive materials to clean the unit.