MODEL RTA-7002 ASSEMBLY INSTRUCTIONS Thank you for purchasing one of our products. Please read carefully the assembly instructions before the installation. Do not discard this manual or any of the packaging material until the unit has been completely assembled.
RTA-7002 P.2 P.
RTA-7002 P.3 P.3 MAIN PARTS LIST Legs Support tube for main panel Support tube for cabinet Cable management (Grommet) Drawer sliders, SET of 4 pcs: - 2 “flat” for inside the cabinets (CL, CR). - 2 “L shaped” for the drawers (DL, DR).
RTA-7002 P.4 P.4 BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS. • Do a quick inventory to make sure the product contains all the parts and hardware. • Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the CONTACT card included with the product. • The replacement parts service is limited to the continental United States. If you reside in Hawaii, Puerto Rico, U.S.
RTA-7002 P.5 P.5 ASSEMBLY STEPS STEP 1 Separate the sliders (24) according to their shapes: The “L” shaped sliders for drawer (DL, DR) will be used until step 6, please set them aside. The flat sliders for cabinet (CL, CR) are the ones being used in step 2. STEP 2 Assemble the flat drawer sliders (24) to the panels (5) and (6) using screws (J) as shown. Note that the wheels face to the front and pay attention to the correct hole for the screw.
RTA-7002 P.6 STEP 4 Screws: A B M6x35mm ⌀8x30 6 pcs P.6 First insert the bolts (A) and the wooden pins (B) into the corresponding holes on panel (4), then install and align the cam locks (A) into panels (5), (6) and (9), then assemble panel (4) as shown and as explained in page 4.
RTA-7002 P.7 STEP 7 Insert the studs (27) into the legs (20) as shown. STEP 8 Assemble the support tubes (22) to the legs (20) using screws (E) as shown. P.7 Screws: E M6x35mm 8 pcs Assemble the bars (22) from each leg to each panel (4) on both cabinets using screws (F) as shown.
RTA-7002 P.8 First insert the nuts (L) into the panel (2) and make sure they are aligned to receive the screws. Then assemble both cabinets to panel (2) using screws (C). Finally, assemble the metal plate (K) to panel (7) using screws (J) as shown. STEP 10 Screws: C M6x50mm 4 pcs J 3x14mm 2 pcs 1 pc K L M6-⌀10 4 pcs First insert and align the cam locks (A) into panels (5), (6), (7), (8) and (9). Then insert the bolts (A) and the wooden pins (B) into the corresponding holes on panels (3).
RTA-7002 P.9 Assemble the support bars (21) to the tabletop (1) using screws (D) as shown. STEP 12 Screws: D M6x40mm 6 pcs P.9 Assemble the support bars (21) to the top panels (3) using screws (E) as shown. STEP 13 Screws: E M6x35mm 8 pcs Note the hole for grommet goes on the back of the tabletop (Tabletop shown Upside-down) STEP 14 Screws: G 3.5x40mm 8 pcs Using screws (G), assemble the back panel (13) to panels (11) and (12), and the panel (17) to panels (15) and (16) as shown.
STEP 16 Screws: A H M6x35mm M4x22mm P.10 RTA-7002 P.10 8 sets First attach the bolts (A) to the panels (10) and (14). Then install the cam locks (A) into panels (11), (12), (15) and (16). Then, and as explained in page 4, assemble the front panel (10) to panels (11) and (12), and the front panel (14) to panels (15) and (16). Finally, install the handles (26) to the front panels (10) and (14) using screws (H) as shown.
P.11 RTA-7002 P.11 1st: Insert the drawers into the cabinet, the bottom drawer first, then the top drawer. The top drawer might need to be inserted at an angle with its front facing down. Screws: 2nd: Assemble the handle (26) to the door (19) using screws (H). M4x22mm 2 3rd: Insert the Grommet (23) into the hole of the tabletop (1). H pcs 4th: Assemble the hinges (25) to panel (8) using screws (I). 3.5x14mm 12 5th: Assemble the door (19) to the hinges (25) using screws (I).
RTA-7002 P.12 P.12 AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING CARE AND MAINTENANCE WARNINGS: WEIGHT LIMITS 110 Lbs. (49.9 Kg) 10 Lbs. (4.53 Kg) 33Lbs. (15 Kg) 15 Lbs. (6.8 Kg) • Do not exceed the indicated weight limits. • Do not expose the surfaces to direct sunlight or to extreme environmental conditions. • Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry with a clean towel.
