User's Manual

Table Of Contents
1
Power
P
o
r
t:
T
h
e
Power port connects the
TG590
R
ou
t
e
r
to an electrical wall outlet via
t
h
e
Power c
o
r
d
.
Power
S
w
i
t
c
h:
T
h
e
Power switch powers the
TG590
R
ou
t
e
r
on and
o
ff
.
R
e
s
e
t
B
u
tt
o
n:
To
restore the
TG590
R
ou
t
e
r
s factory default s
e
tt
i
ng
s
,
press and hold the
R
e
s
e
t
button for approximately five
s
e
c
o
nd
s
.
T
h
e
reset process will start about
t
e
n
seconds after releasing the
b
u
tt
o
n
.
When the
TG590
R
ou
t
e
r
r
e
s
e
t
s
,
all the
li
gh
t
s
on
the front panel turn
o
ff
,
and then some of the lights start
f
l
a
s
h
i
ng
.
T
h
e
TG590
R
ou
t
e
r
has c
o
m
p
l
e
t
e
d
its reset process when the Power light glows s
t
e
a
d
il
y
g
r
ee
n
.
Caution! Do not unplug the Power cord from the
TG590
during
t
h
e
reset
p
r
o
c
e
ss
.
Doing so may result
in the loss of the
TG590
s c
o
n
f
i
g
u
r
a
t
i
o
n
i
n
f
o
r
ma
t
i
o
n
.
If
this
o
cc
u
r
s
,
reset the
TG590
R
ou
t
e
r
a
g
a
i
n
.
LAN
E
t
h
e
r
n
e
t
Ports (4):
T
h
e
LAN
E
t
h
e
r
n
e
t
ports connect devices to the
TG590
R
ou
t
e
r
via
E
t
h
e
r
n
e
t
c
a
b
l
e
s to create a local area network
(
L
A
N
)
.
T
h
e
LAN
E
t
h
e
r
n
e
t
ports are 10/100 Mbps auto-sensing
p
o
r
t
s
,
and either a s
t
r
a
i
gh
t
-
t
h
r
ou
gh
or crossover
E
t
h
e
r
n
e
t
c
a
b
l
e
can be used when connecting devices to the
p
o
r
t
s
.
WAN
E
t
h
e
r
n
e
t
P
o
r
t:
T
h
e
WAN
E
t
h
e
r
n
e
t
port connects the
TG590
R
ou
t
e
r
to the
ISP
using an
E
t
h
e
r
n
e
t
c
a
b
l
e
.
USB
P
o
r
t:
T
h
e
USB
port provides up to 5
VDC
for
attached
devices (to charge a cell
p
h
o
n
e
,
for
e
x
am
p
l
e
)
.
I
n
the
f
u
t
u
r
e
,
with a firmware release
u
p
g
r
a
de
,
the
USB
h
o
s
t
functionality will be available for devices such as
external storage and c
a
m
e
r
a
s
.
Wireless
A
n
t
e
nn
a:
The TG590’s wireless antenna is used to transmit a wireless signal to other wireless devices on its wireless
network. It is built-in.