42pb120S4-en 2/07/04 11:32 Page 1 Table of contents Important safety instructions Warnings and precautions Installation Care and maintenance Trademarks Compliance with CE standards Package contents Understanding your set Front panel Remote control Using the remote control for other equipment Programming the remote control Switching on Channel set-up Initial set-up Manual installation General operation Switching the set on and off Volume Displaying status information Accessing TV channels Accessing AV pr
42pb120S4-en 2/07/04 11:32 Page 2 Important safety instructions Warnings and precautions EN 2 Ensure that your domestic mains supply voltage matches the voltage indicated on the identification label located at the back of the set. The TV set’s components are sensitive to heat.The maximum ambient temperature should not exceed 35° Celsius. Do not cover the vents at the back of the TV set. Leave sufficient space around it to allow adequate ventilation.
42pb120S4-en 2/07/04 11:32 Page 3 Important safety instructions Installation Care and maintenance Install the TV set in a properly ventilated room. Do not install this product on an unstable cart, stand or table. Do not place it on a bed, sofa, rug, or other similar surfaces. Do not install the TV set in an enclosed area unless proper ventilation is provided. Do not rest objects on the power cord and avoid placing power cord near high traffic areas.
2pb120S4-en 2/07/04 11:32 Page 4 Package contents Remote control with batteries TV set EN 4 SIZE AAA 1,5 V 0%MERCURY EXTRA HEAVY DUTY GREENELL + - - + GR EE EX TR NE AH EA SIZ VY LL E AA A 1,5 DU V TY 0%ME RCUR Y User manual 42P B1 20S 4 M an Be Ma Us Ma er nu die nu ma al u el nu al e nu de d’ u ng sa di nle u til al u til til iz ac isa itu t io n ng iz z az io n e ió n Optional accessory You can purchase from your local sales representative an optional w
42pb120S4-en 2/07/04 11:32 Page 5 Understanding your set Front panel EN 5 Power (standby) button Menu On / standby To access the menus. Status light To control the volume. Horizontal scrolling in menus. +/Off When the TV set is connected to the mains, and the main power switch on the rear panel is on the OFF position, the light is off.
42pb120S4-en 2/07/04 11:32 Page 6 Remote control Most of your television’s functions are available via the menus that appear on the screen.The remote control supplied with your set can be used to navigate through the menus and to configure all the general settings.
42pb120S4-en 2/07/04 11:32 Page 7 Remote control Using the remote control for other equipment The remote control supplied with your television can be used to control other appliances using the programmable buttons VCR, DVD, SAT, AMP and AUX. For each button you can control the following appliances: VCR: video recorder DVD: DVD player SAT: satellite receiver, cable network AMP: hi-fi system, Home Cinema amplifier AUX: any appliance.
42pb120S4-en 2/07/04 11:32 Page 8 Remote control Programming the remote control EN 8 Automatic code search Manual programming This method can be used to automatically find the most appropriate code for your appliance. 1. Switch on the appliance you wish to use the remote control with. 2. Press the relevant button for this appliance on the remote control, and while holding this button down, press the button until the light or the appliance buttons of the remote control come on. Release both buttons.
42pb120S4-en 2/07/04 11:32 Page 9 Switching on Follow the instructions on this page to switch on the TV set and the remote control. 1. Install two LR06 or AA batteries in the remote control. Precautions on using batteries: - Only use the battery types specified. - Make sure you use the correct polarity. - Do not mix new and used batteries. - Do not use rechargeable batteries.
42pb120S4-en 2/07/04 11:32 Page 10 Channel set-up Initial set-up The initial set-up involves setting all the parameters required to be able to search and store all the channels you can receive in your area. Make sure that the TV set is switched on and follow steps 1 to 4.When you first switch the TV set on, the language selection menu appears. If this does not happen, refer to the Manual installation section to find out how to carry out an automatic search.
42pb120S4-en 2/07/04 11:32 Page 11 Channel set-up ORGANIZER Return Select PR Swap with PR: Change name Delete PR Select programme with PR-/+ or or 0 to 9 keys. 02 -BBC2 05 4. At the end of the auto installation process, the ORGANIZER menu appears to allow you to modify the order of channels, to name or rename channels, or delete channels stored twice or with poor reception quality. Use a TV programme magazine and the channel logos to identify the various channels.
42pb120S4-en 2/07/04 11:32 Page 12 Channel set-up Manual installation INSTALLATION Return Manual installation Auto installation Organizer MANUAL INSTALLATION EN 12 Return Standard Frequency Name Fine-tuning Store on PR: Decoder Text EURO 150.75 MHz BBC2 02 1 You may want to to carry out a manual installation in case some channels have not been stored during the initial set-up. Setting up channels manually requires every setting to be entered, one at a time.
42pb120S4-en 2/07/04 11:32 Page 13 General operation Switching the set on and off To switch the TV set on, put the main power switch located at the rear on the ON position, then press the power button located on the front panel.When the set is on, the light on the front is green. Standby mode: press the power button on the front panel.When the TV set is in standby mode, the light on the front is orange.
42pb120S4-en 2/07/04 11:32 Page 14 Adjusting the picture Display the OVERVIEW menu using the MENU button. Select Picture and press OK to confirm.The PICTURE menu appears. The contents of this menu depends on the signal. In TV mode: PICTURE menu in TV mode PICTURE EN 14 Return Brightness Contrast Colour Sharpness Tint Tone Auto format Noise reduction Cold Low Adjust the Brightness, Contrast, Colour and Sharpness settings as required.
42pb120S4-en 2/07/04 11:32 Page 15 Adjusting the sound SOUND Return Sound type Bass Treble Balance Intern. speaker Audio output Stereo Fixed Display the OVERVIEW menu using the MENU button. Select Sound and press OK to confirm.The SOUND menu appears, which offers the following settings: The Sound type option allows to select the relevant sound type. Use the buttons to make a selection. The available options depend on the programme you are watching.
42pb120S4-en 2/07/04 11:32 Page 16 Picture in picture (PIP) EN 16 The PIP area on the remote control is used for the PIP functions.These functions allow to view two programmes (one TV channel and one AV programme, or two AV programmes) at the same time in various ways.Press the PIP button to scroll the various display modes: PIP: a TV channel or AV programme is displayed in a frame in a corner of the screen.
42pb120S4-en 2/07/04 11:32 Page 17 Other functions Sleep timer This function allows you to set an automatic shut-off time, from 0 to 4 hours, with 15-minute steps. 3 : 4 5 - : - - Press the red button on the remote control to activate the sleep timer function. A symbol appears on screen in front of the sleep time. If no timer has been set, then -:-- is displayed. Use the buttons to decrease/increase the duration.
42pb120S4-en 2/07/04 11:32 Page 18 Using the teletext The Teletext service is available in many countries under a variety of names (TOP Text, Fastext, FLOF test,Videotext). It is provided as a free service by some television broadcasters.This service provides a real wealth of information, available at any time, on weather, sports results, news, games, etc.
42pb120S4-en 2/07/04 11:32 Page 19 Using the teletext Teletext offers some other useful functions: Newsflash When a newsflash is detected, PAT is replaced by N. Press the blue button to display the newsflash. In the case of an update,Teletext is automatically enabled and displays the new information. To display the header and the navigation bar again, press any button or the volume adjustment buttons) on the (except EXIT, the button remote control.
42pb120S4-en 2/07/04 11:32 Page 20 Connecting other equipment Connecting a DVD player AV1 AV2 Using SCART (AV) socket input 1. Connect the SCART socket on the DVD player to a SCART socket (AV1 or AV2) on the rear panel of the set. Using component video input 1. Connect the green (Y), red (PR/CR), and blue (PB/CB) cinch sockets on the DVD player to the corresponding cinch sockets on the rear panel of the set. 2.
42pb120S4-en 2/07/04 11:32 Page 21 Connecting other equipment Connecting external amplified speakers Connect the red (R) and white (L) audio out sockets located to the right of the connector panel of the set respectively to the right and left amplified speakers. Connecting an amplifier Connect the red (R) and white (L) audio out sockets located to the right of the connector panel to the amplifier’s L and R inputs.
42pb120S4-en 2/07/04 11:32 Page 22 Signal frequency information In PC mode, you can press the yellow INFO button to access the display mode of the TV set. M. xx appears on screen. Please refer to the table below to get detailed information about the various display modes. EN 22 Mode Horizontal 1 31.469 2 37.861 3 37.500 4 43.269 5 35.156 6 37.879 7 48.077 8 46.875 9 53.674 10 48.364 11 56.476 12 60.023 13 68.677 14 63.981 15* 79.976 16* 91.146 18 31.469 19 31.469 20* 45.000 21* 33.750 22 31.469 23 31.
42pb120S4-en 2/07/04 11:32 Page 23 Troubleshooting The following table lists possible problems and methods for remedy. Please refer to this table prior to contacting a service representative. Symptom No picture is displayed. Possible cause 1.The power cord is disconnected. 2.The main power switch on the rear panel is on the OFF position. 3.The selected input has no connection. 4.The TV set is in standby mode in RGB mode. Remedy 1. Plug in the power cord. 2.
42pb120S4-en 2/07/04 11:32 Page 24 Specifications Display panel Screen size Aspect ratio Resolution 42 inches 16:9 wide 852 x 480 Power source EN 24 Input voltage Power consumption Standby & power save 100 ~ 240 V ac , 50 / 60 Hz 240 W (average) 4W Dimensions (W x H x D) Net weight 1200 x 648 x 22 33 kg
42pb120S4-en 2/07/04 11:32 Page 25 Wall mount installation (optional) Package contents An optional wall mount (ACC 913) is available. Contact your local retailer for more information.
42pb120S4-en 2/07/04 11:32 Page 26 Wall mount installation (optional) Installation Step 1. Attach the horizontal supports (C and D) to the left and right modules (A and B) using the appropriate screws (E). EN 26 Step 2. Install the wall mount bracket onto the wall. Note: This package includes two different sets of screws - one for mounting on a cement wall and one for a wooden wall. Please consult with a qualified installer to make sure that this wall mount and TV set can be installed.
42pb120S4-en 2/07/04 11:32 Page 27 Wall mount installation (optional) Step 3. Remove the table-top stand, and install the TV set onto the wall mount bracket. EN 27 Note: This wall mount is an optional accessory, please contact your retailer for more information. This type of equipment is to be installed by qualified installers, please contact with authorized dealer for installation. Please make sure that the wall can support the wall mount and TV set.
