SpeedTouch™ 605/608/608 WL/620 (Wireless) Business DSL Routers User’s Guide Release R5.3.
SpeedTouch™ 605/608 608 WL/620 User’s Guide R5.3.
Copyright Copyright ©1999-2005 THOMSON. All rights reserved. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document.
Contents Contents About this User’s Guide .............................................. 1 1 Your SpeedTouch™ ...................................................... 3 1.1 SpeedTouch™ Features .................................................................. 4 1.1.1 Hardware Specifications .................................................................................. 5 1.1.2 Software Features .......................................................................................... 6 1.
Contents ii 3.3 MS Windows XP BroadBand Connection ..................................... 39 3.4 Mac OS X PPPoE Dial-in Client .................................................... 43 4 Basic Configuration .................................................... 45 4.1 Navigation.................................................................................... 46 4.1.1 Menu .......................................................................................................... 47 4.1.
Contents 4.5 Toolbox ........................................................................................ 67 4.5.1 Remote Assistance ....................................................................................... 68 4.5.2 Game & Application Sharing .......................................................................... 69 4.5.3 Defined Games & Applications ....................................................................... 70 4.5.4 Game or Application Definition ................
Contents iv 5.2 SpeedTouch™............................................................................. 104 5.2.1 Easy Setup ................................................................................................ 105 5.2.2 System Information .................................................................................... 106 5.2.3 Connections .............................................................................................. 108 5.2.4 Diagnostics..........................
Contents 5.7 VPN ............................................................................................ 172 5.7.1 LAN to LAN ............................................................................................... 173 5.7.2 VPN Client................................................................................................. 174 5.7.3 VPN Server................................................................................................ 175 5.7.4 Certificates .................
Contents vi E-DOC-CTC-20050429-0104 v1.
About this User’s Guide About this User’s Guide Used Symbols A note provides additional information about a topic. A tip provides an alternative method or shortcut to perform an action. ! Terminology Typographical Conventions A caution warns you about potential problems or specific precautions that need to be taken. Generally, the SpeedTouch™605(i), the SpeedTouch™608(i), the SpeedTouch™608(i) WL, and the SpeedTouch™620(i) will be referred to as SpeedTouch™ in this User’s Guide.
About this User’s Guide 2 E-DOC-CTC-20050429-0104 v1.
Chapter 1 Your SpeedTouch™ 1 Your SpeedTouch™ Introduction With the SpeedTouch™605(i) and SpeedTouch™608(i) Business DSL Routers and the SpeedTouch™608 WL(i) and SpeedTouch™620(i) Wireless Business DSL Routers you can build a secure small (home-)office network, seamlessly connecting wired and wireless devices and surf the Internet at high speed, all combined in one device.
Chapter 1 Your SpeedTouch™ 1.1 SpeedTouch™ Features Introduction Your SpeedTouch™ offers you a wide range of outstanding features. In this section you will find a comprehensive overview of the: 4 Hardware Specifications Software Features E-DOC-CTC-20050429-0104 v1.
Chapter 1 Your SpeedTouch™ 1.1.1 Hardware Specifications Router Physical interfaces Integrated multi-mode ADSL modem, supporting: ADSL over POTS for a SpeedTouch™ ADSL/POTS variant) ADSL over ISDN for a SpeedTouch™ ADSL/ISDN variant) ADSL/RE-ADLS2/ADSL2/ADSL2+ for both ADSL over POTS and ADSL over ISDN WAN: LEDs Reset button Association button Wireless performance Memory and CPU Cardbus E-DOC-CTC-20050429-0104 v1.
Chapter 1 Your SpeedTouch™ 1.1.2 Software Features ADSL compliance ATM features Bridging features Routing features 6 If POTS in overlay: G. handshake, Full Rate ADSL, G.dmt, G.lite (splitterless ADSL), ADSL2, RE-ADSL and ADSL2+ If ISDN in overlay: G.handshake, G.dmt, ADSL2, RE-ADSL and ADSL2+ Up to 16 simultaneous PVCs, allowing multiple simultaneous destinations ATM QoS per PVC: CBR, VBR-rt, VBR-nrt, UBR Service monitoring through ITU-T I.
Chapter 1 Your SpeedTouch™ Networking services Security Configuration E-DOC-CTC-20050429-0104 v1.0 UPnP with NAT traversal capability: enables game technologies (Xbox live, Direct X, and many others) enables conferencing functions of Microsoft Messenger Transparent bridging (IEEE802.
Chapter 1 Your SpeedTouch™ Management and monitoring VoIP Multi-level user protection, Event logging DHCP server, client and relay, DHCP-to-PPP spoofing DNS server, client and relay Time synchronization: SNTPv1, SNTPv2, SNTPv3 and SNTPv4 integrated Real-Time Clock in case of SpeedTouch™608 WL/620 (for nonvolatile time-of-day) Syslog SNMPv1 support for:MIB II (RFC1213/2011/2012/2013), traps MIB (RFC1215), bridge MIB (RFC1286/1493), ATM TC MIB (RFC2514), ATM MIB (RFC1695/2515), A
Chapter 1 Your SpeedTouch™ 1.2 SpeedTouch™ LED Behaviour The SpeedTouch™ is equipped with a number of LEDs on its front panel, indicating the state of the device during normal operation.
Chapter 1 Your SpeedTouch™ Indicator Description Name Colour State ISDN Green Flashing ISDN activity On ISDN line connected, no activity Off DSL Green No ISDN line Flashing Pending DSL line synchronisation On DSL line synchronised Off Internet Green Red No DSL line Flashing Internet activity On Internet connectivity, no activity On Internet connection setup failed Off Ethernet LEDs No Internet connection A LED may be provided per Ethernet port to indicate link integrity (or act
Chapter 1 Your SpeedTouch™ 1.3 How to Access your SpeedTouch™ Access methods Your SpeedTouch™ is accessible in one of following ways: Access Method Can be used to: Web Configure your SpeedTouch™ via HTTP or HTTPS. For more information, see “1.3.1 Access via the Web Interface” on page 12. E-DOC-CTC-20050429-0104 v1.0 Command Line Interface (CLI) Fine tune your SpeedTouch™ configuration. For more information, see “1.3.2 Access via CLI” on page 13.
Chapter 1 Your SpeedTouch™ 1.3.1 Access via the Web Interface Procedure To access the SpeedTouch™ via the web interface: 1 Open a web browser. 2 In the address bar type your SpeedTouch™’s IP address or DNS host name, by default that is ‘http://speedtouch.lan’ or ‘192.168.1.254’. You can access the pages via the http protocol.
Chapter 1 Your SpeedTouch™ 1.3.2 Access via CLI Command Line Interface (CLI) You can access the Command Line Interface (CLI) via: The embedded Expert pages. For more information, see “5 Expert Configuration” on page 101. A Telnet session This requires that TCP/IP connectivity exists between the host from which the Telnet session is opened and the SpeedTouch™. Your SpeedTouch™ and the connected PC must have an IP address in the same subnet.
Chapter 1 Your SpeedTouch™ Telnet session Proceed as follows: 1 Open a telnet application. You can use the Command Prompt window. In Windows XP for instance: 2 1 On the Windows task bar, click Start. 2 Select (All) Programs > Accessories > Command Prompt. Connect to your SpeedTouch™. . In the Command Prompt window: At the prompt, type telnet followed by the IP address of your SpeedTouch™ (default is 192.168.1.254). 3 Enter your SpeedTouch™ security user name and password.
Chapter 1 Your SpeedTouch™ 1.3.3 Access via FTP File Transfer Protocol (FTP) File system FTP session You can access the file system of the SpeedTouch™ via the File Transfer Protocol (FTP), in order to: Restore or backup configuration files, templates or language packs. Upgrade your configuration or firmware. The SpeedTouch™ file system is stored on nonvolatile memory, and contains the SpeedTouch™ software, service template files and (optionally) default setting files.
Chapter 1 Your SpeedTouch™ File system access rights Common FTP commands On the different directories you have following privileges: Directory Access rights root NO read/write active read-only dl read/write Depending on the access rights you have on a directory, you can use one of following commands: Command... You can use to... cd access another directory than the one currently open. Example: ftp>cd dl. dir list the directory files. Example: ftp>dir.
Chapter 1 Your SpeedTouch™ FTP file transfer To allow correct file transfers, set the transfer mode to “binary”: At the ftp prompt, type bin and press Enter. Turn on the hashing option to see the progression of the file transfer: At the ftp prompt type hash and press Enter. Example: /home/doejohn{1}$ftp 192.168.1.254 Connected to 192.168.1.254 220 Inactivity timer = 120 seconds. Use 'site idle ' to change. Name (192.168.1.254:doejohn): 331 SpeedTouch™ (00-90-D0-01-02-03) User 'doejohn' OK.
Chapter 1 Your SpeedTouch™ 1.3.4 Remote Assistance Remote access Enabling remote access You can make your SpeedTouch accessible from the Internet with regard to remote support. This way, you can allow your helpdesk to access your SpeedTouch™ remotely. To enable remote assistance: 1 Go to the SpeedTouch™ pages, as described in “1.3.1 Access via the Web Interface” on page 12. 2 In the menu select Toolbox > Remote Assistance. 3 Click Enable Remote Assistance.
Chapter 2 Local Network Setup 2 Local Network Setup Introduction Device settings E-DOC-CTC-20050429-0104 v1.0 The SpeedTouch™ offers you following local networking solutions: Wired Ethernet Wireless Ethernet Once you’ve connected a device, you are able to personalise its settings: 1 Go to the SpeedTouch™ web pages. 2 In the menu select Home Network > Devices. 3 Click the name of your device, or if the device’s settings haven’t been personalised yet, click the MAC address of the device.
Chapter 2 Local Network Setup 2.1 Wired Ethernet Local network The Ethernet ports on the backpanel allow you to connect the SpeedTouch™ to an existing 10 or 100 Base-T Ethernet network or one (or more) computer(s) with installed Ethernet card. Using the SpeedTouch™ Ethernet switch, you can create a local Ethernet network of up to four devices, without needing extra networking devices. In the SpeedTouch™ package, a yellow full-wired straight-through RJ-45/RJ45 Ethernet cable is included.
Chapter 2 Local Network Setup 2.2 Wireless Ethernet Introduction The SpeedTouch™ 608 WL/620Wi-Fi® certified IEEE 802.11g compliant wireless access point allows multiple computers to connect wirelessly to your local network over the SpeedTouch™ Wireless LAN environment. The SpeedTouch™ is backward compatible with IEEE 802.11b, which means 802.11b and 802.11g devices can coexist in the same wireless network.
Chapter 2 Local Network Setup 2.2.1 Wireless Basics Introduction In this section some key wireless concepts are explained. 802.11b/g 802.11b is an IEEE standard, operating at 2,4 GHz at a speed of up to 11 Mb/s. 802.11g, a newer IEEE standard also operating at 2,4 GHz, gives you up to 54 Mb/s speed, more security and better performance. Wireless Fidelity Access Point The Wi-Fi certification ensures that your SpeedTouch™ will interoperate with any WiFi certified 802.11g and 802.
Chapter 2 Local Network Setup Antennas Direct the external antenna to allow optimization of the wireless link. If for example the antenna is erect, wireless links in the horizontal plane are favoured. Please note that the antenna characteristics are influenced by the environment, that is by reflections of the radio signal against walls or ceilings.
Chapter 2 Local Network Setup 2.2.2 Connecting First-time Wireless Clients Wireless default settings After every Reset-to-Defaults, the SpeedTouch™ wireless access point configuration is returned to its initial default settings. These default settings are: Security level is low (security disabled) for an easy first use, meaning the data will not be encrypted. Wireless security settings are described in “2.2.3 Wireless Security” on page 27. The SpeedTouch™ is broadcasting its network name (SSID).
Chapter 2 Local Network Setup To associate your wireless client to the SpeedTouch™: 1 Click the network icon in the notification area: 2 The Wireless Network Connection window appears: In the Choose a wireless network list, select the SpeedTouch™ wireless network and click Connect. 3 Following window appears: Click Connect Anyway. 4 Your computer is now connected to the SpeedTouch™ wireless network.
Chapter 2 Local Network Setup Wireless device settings Once you’ve connected a device, you are able to personalise its settings. For more information, see “ Device settings” on page 19. To add a wireless device to the Access Control List (ACL), select Allowed on WLAN. 26 E-DOC-CTC-20050429-0104 v1.
Chapter 2 Local Network Setup 2.2.3 Wireless Security Introduction Since the SpeedTouch™ wireless environment is a radio environment, precautions must be taken to ensure that your wireless network is safe from malicious intruders.
Chapter 2 Local Network Setup Data encryption To setup wireless connectivity, you can choose different levels of security: Low (Security disabled, the default): No security; the data will not be encrypted, no authentication process will be used. Medium: Use WEP (Wired-Equivalent Privacy) to encrypt the traffic between the SpeedTouch™ and the clients by sharing a pre-defined 64-bit or a 128-bit Network key for secure communication with legacy 802.11b clients.
Chapter 2 Local Network Setup 2.2.4 Connecting Additional Wireless Clients Preconditions Security issues Registering wireless clients Registering clients via web pages E-DOC-CTC-20050429-0104 v1.0 Make sure that: The SpeedTouch™ is powered on and ready for service. The SpeedTouch™ has been configured as DHCP server (default). The wireless client adapters have been installed on all computers you want to connect to the WLAN.
Chapter 2 Local Network Setup Registering clients via association button You can easily register new wireless network clients as follows: 1 Push the Association button on the SpeedTouch™ back panel for at least two seconds. The WLAN LED will toggle between green and red. The ACL will be unlocked for a time frame of one minute.
Chapter 2 Local Network Setup 2.2.5 Extending the Range of Your Wireless Network WDS The SpeedTouch™ features Wireless Distribution System (WDS) functionality. This feature allows you to extend the range of your wireless network by introducing one or more WDS-enabled devices into your wireless network. The Wireless Distribution System (WDS) enables data packets to pass from one wireless access point to another, just as if the access points were ports on a wired Ethernet switch.
Chapter 2 Local Network Setup Configuring WDS To configure your WDS on the web pages: 1 Go to the SpeedTouch™ web pages. 2 In the menu select Home Network. 3 Click your WLAN. 4 On the top right, click Configure. If not already done, set a fixed channel and check whether the security settings (WEP encryption or no encryption) on your SpeedTouch™ are the same as on the repeater. 5 On the Wireless Access Point page, in the Pick a task... list, click Configure WDS. 6 Select WDS Enabled.
Chapter 3 Internet Connectivity Dial-In Clients 3 Internet Connectivity Dial-In Clients Introduction Access methods For setting up initial Internet connectivity, using the Home Install Wizard on the Setup CD or the embedded Easy Setup, refer to the provided Installation and Setup Guide. Depending on the configuration of the SpeedTouch™ you may have: Direct access: As soon as the initial configuration has been done, immediate and uninterrupted WAN access is provided.
Chapter 3 Internet Connectivity Dial-In Clients Embedded PPP dial-in clients The SpeedTouch™’s embedded PPP dial-in client allows you to establish an Internet connection for computers residing on your local network, using only one computer of the network to control the client. If this computer runs: Broadband host PPPoE dial-in clients Any Operating System you can always use the SpeedTouch™ web pages. See “3.1 SpeedTouch™ Web Pages” on page 35 to proceed.
Chapter 3 Internet Connectivity Dial-In Clients 3.1 SpeedTouch™ Web Pages Introduction As the SpeedTouch™ web pages are controllable from any Operating System with an installed web browser, the method to establish PPP sessions described below you can use on any computer system. For more information on Internet connection setup, see the provided Installation and Setup Guide.
Chapter 3 Internet Connectivity Dial-In Clients Terminating an Internet session To close an active PPP connection: 1 Go to the SpeedTouch™ Home page. 2 Click Disconnect at the appropriate broadband connection. As a result the SpeedTouch™’s embedded PPP dial-in client will close the Internet connection. The Internet Link status will change to Disconnected and your PC is offline. 36 E-DOC-CTC-20050429-0104 v1.
Chapter 3 Internet Connectivity Dial-In Clients 3.2 IGD Control Agent Introduction MS Windows XP users can easily establish PPP sessions, thanks to MS Windows XP’s Internet Gateway Device (IGD) Discovery and Control Client that allows you to control the SpeedTouch™ directly from you PC. The IGD control client only allows to connect or to disconnect a fully configured connection.
Chapter 3 Internet Connectivity Dial-In Clients Internet connection status Terminating an Internet session As long as the SpeedTouch™’s embedded PPP dial-in client is connected, you are able to overview the connection status and some counters by double-clicking the Internet Connection icon in your PC’s Network Connections window: Proceed as follows: 1 In the Windows task bar, click Start. 2 Select (Settings >) Control Panel > (Network and Internet Connections >) Network Connections.
Chapter 3 Internet Connectivity Dial-In Clients 3.3 MS Windows XP BroadBand Connection Prerequisites Configuring a broadband connection To be able to use the MS Windows XP BroadBand Connection, your SpeedTouch™ must be configured for either: Bridging, or PPPoE Relay Proceed as follows: 1 On the Start menu, click (Settings >) Control Panel. 2 The Control Panel window appears. Go to (Network and Internet Connections >) Network Connections.
Chapter 3 Internet Connectivity Dial-In Clients 8 Select whether the connection will be available to any user or only to yourself: 9 Fill in the Internet account information. This information should be provided by your service provider: 10 At the end of the configuration the following window appears: Click Finish to complete the configuration. The Connect YourISP window (see below) appears. 40 E-DOC-CTC-20050429-0104 v1.
Chapter 3 Internet Connectivity Dial-In Clients Starting a broadband Internet session Proceed as follows: 1 On the Start menu, point Connect To and click the name of the connection you’ve created, for example YourISP. If you are using the Classic Start menu click Start > Settings > Network (and Dial-up) connections > YourISP. E-DOC-CTC-20050429-0104 v1.0 2 The Connect YourISP window appears: 3 If requested, enter user name and password for your user account at the Service Provider.
Chapter 3 Internet Connectivity Dial-In Clients Terminating a broadband Internet session Proceed as follows: 1 On the Start menu, point Connect To and click the name of the connection you’ve created, for example YourISP. If you are using the Classic Start menu go to Start > Settings > Network (and Dial-up) connections > YourISP. 42 2 The YourISP Status window appears: 3 Click Disconnect. 4 The connection is released. As a result no Internet connectivity exists any more.
Chapter 3 Internet Connectivity Dial-In Clients 3.4 Mac OS X PPPoE Dial-in Client Prerequisites Configuring a broadband connection To be able to use the MS Windows XP BroadBand Connection, your SpeedTouch™ must be configured for either: Bridging, or PPPoE Relay Proceed as follows: 1 On the Apple menu, click System Preferences. 2 In the System Preferences window, click the Network icon. 3 The Network window appears.
Chapter 3 Internet Connectivity Dial-In Clients Starting a broadband Internet session Proceed as follows: 1 Click the Internet Connect dockling. If the Internet Connect dockling is not available, go to the Applications folder on the system startup disk and double-click Internet Connect. 2 The following window appears: Make sure Built-in Ethernet is selected in the Configuration list.
Chapter 4 Basic Configuration 4 Basic Configuration Introduction The SpeedTouch™ comes with embedded HTML pages, providing an interface to the software installed on the device. It allows easy setup and management of the SpeedTouch™ via your web browser form any PC connected to the SpeedTouch™. See “1.3.1 Access via the Web Interface” on page 12 to access the pages. Basic and Expert Mode SpeedTouch™ documentation E-DOC-CTC-20050429-0104 v1.
Chapter 4 Basic Configuration 4.1 Navigation Navigation components The SpeedTouch™ web interface consists of following components: Menu Language Bar Navigation Bar Notification Area Tasks Navigation bar Notification area Language bar Menu Tasks 46 E-DOC-CTC-20050429-0104 v1.
Chapter 4 Basic Configuration 4.1.1 Menu Menu items Collapsing and expanding the menu E-DOC-CTC-20050429-0104 v1.0 The menu is located on the left side of the page and consists of the following menu items: SpeedTouch: Provides basic information on the SpeedTouch™. Broadband Connection: Allows you to view/configure your broadband connections. Toolbox: Allows you to assign games or applications to a device and secure your Internet connection.
Chapter 4 Basic Configuration 4.1.2 Language Bar Language bar The language bar is located under the SpeedTouch™ logo and allows you to change the language of the SpeedTouch™ web interface. ! 48 The language bar will only be shown if more than one language is available. E-DOC-CTC-20050429-0104 v1.
Chapter 4 Basic Configuration 4.1.3 Navigation Bar Navigation bar Display level E-DOC-CTC-20050429-0104 v1.0 The navigation bar is located on the top of the page and allows you to: View the current user name. Click this name to change your password or switch to another user. View the current position on the SpeedTouch™ web interface. Get context related Help information.
Chapter 4 Basic Configuration 4.1.4 Notification Area Notification area The notification area is located under the Navigation Bar and is used to display: Error messages indicated by a red traffic light. Warnings indicated by an orange traffic light. Information indicated by a green traffic light. If none of these events occur, the notification area will not be shown. 50 E-DOC-CTC-20050429-0104 v1.
Chapter 4 Basic Configuration 4.1.5 Tasks Tasks E-DOC-CTC-20050429-0104 v1.0 To allow a swift configuration of your SpeedTouch™, some pages may offer you a number of related tasks. These tasks will guide you to the page where you can perform the selected task.
Chapter 4 Basic Configuration 4.2 Home SpeedTouch™ home page 52 The SpeedTouch™ home page gives you a short overview of all the configurable aspects of the SpeedTouch™: SpeedTouch Broadband Connection Toolbox Office Network E-DOC-CTC-20050429-0104 v1.
Chapter 4 Basic Configuration 4.3 SpeedTouch The SpeedTouch menu The SpeedTouch page E-DOC-CTC-20050429-0104 v1.
Chapter 4 Basic Configuration 4.3.1 Information Information 54 The Information page summarizes important information on your SpeedTouch™. You may need this information when you contact your helpdesk. E-DOC-CTC-20050429-0104 v1.
Chapter 4 Basic Configuration 4.3.2 SpeedTouch™ Easy Setup Easy Setup Wizard This wizard helps you configure your SpeedTouch™ Internet connection. To configure the SpeedTouch™ using the SpeedTouch™ Easy Setup wizard: E-DOC-CTC-20050429-0104 v1.0 1 On the left menu, click SpeedTouch. 2 In the Pick a task... list, click Set up. 3 The Easy Setup wizard will now guide you through the configuration of your SpeedTouch™.
Chapter 4 Basic Configuration 4.3.3 Restart Accessing the Restart page Restarting your SpeedTouch™ 56 Proceed as follows: 1 On the left menu, click SpeedTouch. 2 In the Pick a task... list, click Restart. Proceed as follows: 1 Click Yes, restart my SpeedTouch. 2 The SpeedTouch™ restarts. 3 The SpeedTouch™ returns to the Home page. E-DOC-CTC-20050429-0104 v1.
Chapter 4 Basic Configuration 4.3.4 Configuration Overview Details Configure The Overview page displays the current configuration of your SpeedTouch™. The Details page displays more detailed information on the current configuration of your SpeedTouch™. The Configure page allows you to change the current configuration. If you want to: Reconfigure your SpeedTouch™: Click Configuration Wizard under Service Configuration. For more information, see “4.3.2 SpeedTouch™ Easy Setup” on page 55.
Chapter 4 Basic Configuration 4.3.5 Backup & Restore Introduction Accessing the Backup & Restore page Saving your current configuration Restoring a previously saved configuration 58 This page allows you to: Save your current configuration. Restore a previously saved configuration. Proceed as follows: 1 On the SpeedTouch menu, click Configuration. 2 Click Configure. 3 In the Pick a task... list, click Save or Restore Configuration. Proceed as follows: 1 Click Backup Configuration Now.
Chapter 4 Basic Configuration 4.3.6 Reset to Factory Defaults Introduction Accessing the Reset to Factory Defaults page Resetting the SpeedTouch™ to factory defaults E-DOC-CTC-20050429-0104 v1.0 This page allows you to reset the SpeedTouch™ to return to the initial configuration of your SpeedTouch™. All your changes will be deleted. Proceed as follows: 1 On the left menu, click SpeedTouch. 2 In the Pick a task... list, click Return to Factory Default Settings.
Chapter 4 Basic Configuration 4.3.7 Event Logs Event Logging The Event Logs page summarizes the latest events recorded on your SpeedTouch™. Recorded Events table The Recorded Events table gives you an overview of the latest event logs that have been recorded since power on. The first column of the table indicates the importance of the event log Indicator Description Informational Warning Error The Category list allows you to filter the events shown in the Recorded Events table.
Chapter 4 Basic Configuration 4.3.8 Update Updating the SpeedTouch™ system software E-DOC-CTC-20050429-0104 v1.0 The Update page allows you to: View System Information. View information on the current System Firmware. Update your SpeedTouch™ from a remote server. Use this option if you want to have yourSpeedTouch™ check on the internet for new firmware and update if it found one. Update from a PC. Use this option if you want to install on your SpeedTouch™ that is located on the PC.
Chapter 4 Basic Configuration 4.4 Broadband Connection The Broadband Connection menu The Broadband Connection page The Broadband Connection menu consists of following menu items: DSL Connection Internet Services The Broadband Connection page gives you a short status overview of the connections configured on the SpeedTouch™. Click View more to see more information on the selected broadband connection.
Chapter 4 Basic Configuration 4.4.1 Connectivity Check Introduction Accessing the Connectivity Check page Checking you Internet Connectivity Analysing the test results E-DOC-CTC-20050429-0104 v1.0 This page enables you to perform a connectivity check on an Internet service of your SpeedTouch™. Proceed as follows: 1 On the left menu, click Broadband Connection. 2 In the Pick a task... list, click Check connectivity to the Internet.
Chapter 4 Basic Configuration 4.4.2 DSL Connection Overview Details 64 Click Overview to view brief information on your DSL connection. Click Details to view a more detailed information on your DSL connection. E-DOC-CTC-20050429-0104 v1.
Chapter 4 Basic Configuration 4.4.3 Internet Services Internet Services information The Internet Services page displays information on your Internet Connection(s). If you configured a dial-up connection you are able to establish/terminate the connection by clicking Connect/Disconnect. To view more detailed information on a specific connection, click the View more... link of the corresponding connection. E-DOC-CTC-20050429-0104 v1.
Chapter 4 Basic Configuration 4.4.4 Internet Service Settings Accessing the Internet Service Settings page Overview Proceed as follows: 1 On the Broadband Connection menu click Internet Services. 2 Click the View more link of the internet service you want to view. The Overview page gives you basic information on the selected Internet Service. If you configured a connection you are able to establish/terminate the connection by clicking Connect/Disconnect.
Chapter 4 Basic Configuration 4.5 Toolbox The Toolbox menu The Toolbox page E-DOC-CTC-20050429-0104 v1.0 The Toolbox menu consists of following menu items: Remote Assistance: Allows you to make your SpeedTouch™ accessible for remote support. Game & Application Sharing: Allows you to share services and games that you run in your private network towards the internet. Web Site Filtering: Allows you to block/allow access to specific web sites.
Chapter 4 Basic Configuration 4.5.1 Remote Assistance Enabling Remote Assistance This page allows you to make your SpeedTouch™ accessible for remote support. You must be connected to the Internet to be able to enable remote assistance. ! To use remote assistance: 1 If needed, type a password in the Password box. 2 Click Enable Remote Assistance.
Chapter 4 Basic Configuration 4.5.2 Game & Application Sharing Overview Configure The Overview page summarizes the games and applications on a particular host on your network, for which the SpeedTouch™ accepts connections coming from the Internet. The Configuration page allows you to: Select Use UPnP to enable UPnP on the SpeedTouch™. Universal Plug and Play is an architecture for transparent peer-to-peer connectivity of PCs, intelligent appliances, and (wireless) devices.
Chapter 4 Basic Configuration 4.5.3 Defined Games & Applications Accessing the Defined Games & Applications page Proceed as follows: The Defined Games & Applications page This page gives you an overview of the games and applications defined on your SpeedTouch™. Each game or application can be assigned to a device on your local network. 1 In the Toolbox menu, click Game & Application Sharing. 2 In the Pick a task... list, click Modify a game or application.
Chapter 4 Basic Configuration 4.5.4 Game or Application Definition Accessing the Game or Application Definition page Overview Proceed as follows: 1 In the Toolbox menu, click Game & Application Sharing. 2 In the Pick a task... list, click Modify a game or application. 3 Click the name of the game or application you want to view/change. This page gives you an overview of the port mappings used to allow this service or game to be initiated from the Internet.
Chapter 4 Basic Configuration 4.5.5 New Game or Application Accessing the Game or Application Definition Creating a new game or application 72 Proceed as follows: 1 On the Applications page, click Game & Application Sharing. 2 In the Pick a task... list, click Create a new game or application. Proceed as follows: 1 Type the name of the game or application in the Name box.
Chapter 4 Basic Configuration 4.5.6 Web Site Filtering Web Site Filtering The SpeedTouch™ allows you to block/allow particular web sites: Based on the web site’s URL. As within a web site lots of references can be made to other URLs, it is recommended to use this feature in combination with content based filtering. Based on the web site’s content. Redirect a web site to another web site.
Chapter 4 Basic Configuration Deny access to a specific web site Use this feature if: Allow is selected under Action for Unknown Sites. Block is selected under Action for Unknown Sites and you want to make an exception on an allow rule. For example: you are allowing “provider.com” but you want to deny access to “mail.provider.com”. A content category/group is allowed by Content Based Filtering and you want to make an exception.
Chapter 4 Basic Configuration Redirecting all web sites Configure content based filtering settings Proceed as follows: 1 Type “*” in the Web Site box. 2 Click Redirect in the Action list. 3 Type the URL of the web site you want to redirect to (for example “mycompany.com/internetpolicy.htm”) in the Redirect box. 4 Click Add. 5 Type the URL of the web site you want to redirect to (for example “mycompany.com/internetpolicy.htm”) in the Web Site box. 6 Click Allow in the Action list.
Chapter 4 Basic Configuration 4.5.7 Web Filtering Activation Accessing this page Web Filtering Activation page Standard license activation 76 Proceed as follows: 1 On the Toolbox menu, click Parental Control. 2 In the Pick a task... list, click Activate Web filtering License. This page allows you to: Activate a Web Filtering evaluation license. Activate a free 30-days Web Filtering evaluation license. Proceed as follows: 1 Click Standard.
Chapter 4 Basic Configuration 4.5.8 Content Level Accessing this page Overview Proceed as follows: 1 On the Toolbox menu, click Parental Control. 2 Click Configure. 3 Click the Edit link of the content level you want to edit. This page gives you an overview of the different categories and their rules. Following icons indicate whether the content type is allowed or not: Icon Description The category/group is allowed The category/group is not allowed. The group is partly allowed.
Chapter 4 Basic Configuration 4.5.9 New Content Level Introduction Procedure This page allows you to create a new content level. To access this page: 1 On the Toolbox menu, click Parental Control. 2 In the upper right corner, click Configure. 3 Under Pick a task..., click Create a new content level.
Chapter 4 Basic Configuration Content level activation E-DOC-CTC-20050429-0104 v1.0 To activate your new content level: 1 On the Toolbox menu, click Parental Control. 2 In the upper right corner, click Configure. 3 In the Content Level list, select your new content level. 4 The new content level is now active.
Chapter 4 Basic Configuration 4.5.10 Firewall Overview Configure The Overview page summarizes the overall security policy configured on your SpeedTouch™. The Configure page allows you to select the security level of the SpeedTouch™. Select one of following security levels: 80 Medium: Use this Security Level to allow all outgoing connections except Windows protocols (Netbios, RPC, SMB) and block all incoming connections. Game and Application sharing is allowed by the firewall.
Chapter 4 Basic Configuration 4.5.11 Intrusion Detection Intrusion Detection Your SpeedTouch™ is protecting your network against malicious intrusions. This page shows you the intrusions you are protected against. The Protected Intrusions table shows the number of times the SpeedTouch™ actively protected your network against each intrusion since last statistics reset. E-DOC-CTC-20050429-0104 v1.
Chapter 4 Basic Configuration 4.5.12 Dynamic DNS What is Dynamic DNS Overview Configure The Dynamic DNS service allows you to assign a dynamic DNS host name (e.g. john.dyndns.org) to a broadband connection even if it is using a dynamic IP address. As soon as the device gets a new IP address, the dynamic DNS server updates its entry to the new IP address. Click Overview to view the different Dynamic DNS clients with their name, hostnames, interface and IP address.
Chapter 4 Basic Configuration 4.5.13 User Management Overview The Overview page gives you an overview of the currently configured users and their privileges. Clicking the name of a user allows you to edit his user account. Configure E-DOC-CTC-20050429-0104 v1.0 The Configure page allows you to: Click Add to create a new user account. Click Delete to remove a user. Click Edit to change a user account.
Chapter 4 Basic Configuration 4.5.14 Edit User Accessing the User Edit page Editing a user account Proceed as follows: 1 On the Toolbox menu, click User Management. 2 Under Local User Data, click on the name of the user you want to edit. The Edit User page allows you to: Click Reset Password to reset the password of the selected user to the user name. So, if you reset the password of John his password will be “John”. Change the administration privileges of the selected user.
Chapter 4 Basic Configuration 4.5.15 Change Default User Changing the default user This page allows you to change the default user. If users browse to the SpeedTouch™ web pages, they will be automatically logged in under this account. ! E-DOC-CTC-20050429-0104 v1.0 To allow users to automatically log on under this account, this default user account must be configured with a blank password.
Chapter 4 Basic Configuration 4.5.16 Add User Adding users This page allows you to add a new user. Under User definition you can configure: The name of the new user. The password of the new user will be equal to the user name; for example if the user name is John Doe, the password will be John Doe. Also when resetting a user, the password will be changed into the user name.
Chapter 4 Basic Configuration 4.6 Office Network Office Network Menu The Office Network page Viewing (wireless) client information E-DOC-CTC-20050429-0104 v1.0 This menu consists of following items: Devices Allows you the view/configure the devices detected on your local network. Interfaces Allows you to view/configure the interfaces that are available on the SpeedTouch™. The Office Network gives you an overview of your SpeedTouch™ network.
Chapter 4 Basic Configuration 4.6.1 Devices Overview Configure The Overview page gives you an overview of the devices that are currently connected to the SpeedTouch™ network. Click on a device name to get more information on a specific device. The Configure page gives you an overview of the devices that are currently connected to the SpeedTouch™ network. To: Get more information on a specific device, click on the name of the device. See “4.6.2 Device Settings” on page 89 for more information.
Chapter 4 Basic Configuration 4.6.2 Device Settings Accessing the device settings page Overview Proceed as follows: 1 On the Office Network menu, click Devices. 2 In the Detected Device(s), click the name of the device you want to view. The Overview page displays following information: Configure E-DOC-CTC-20050429-0104 v1.0 Information allows you to view: Status shows whether the device is currently connected to the SpeedTouch™ network. Type shows the device type.
Chapter 4 Basic Configuration 4.6.3 Assign Public IP Introduction This page allows you to assign the public IP address of your Internet Connection(s) to a specific device on your local network. You might want to do this if: You do not want to use the Network Address Translation engine of your SpeedTouch™. This device is running server applications (web server,...) and you want it to be accessible from the Internet.
Chapter 4 Basic Configuration 4.6.4 Wireless Device Settings Accessing the wireless device settings page Overview Proceed as follows: 1 On the Office Network menu, click Devices. 2 In the Detected Device(s), click the name of the wireless device you want to view. The Overview page displays following information: Configure E-DOC-CTC-20050429-0104 v1.0 Information allows you to view: Status displays whether the device is currently connected to the SpeedTouch™ network.
Chapter 4 Basic Configuration 4.6.5 Access Point Settings Accessing the Access Point settings Proceed as follows: 1 On the left menu, click Office Network. 2 Under Wireless, click the name of the Access Point you want to view or configure. The Access Points names are of the following format: “WLAN: “ + Network Name, for example “WLAN: SpeedTouch123456”. Overview Details Configure The Overview page displays a brief overview of the current configuration.
Chapter 4 Basic Configuration Under Security following fields are available: Broadcast Network Name: By default the SpeedTouch™ broadcasts its network name, allowing you to easily recognise your wireless network in the list of available networks. Once you have configured your wireless clients, it is recommended to disable this feature by clearing this check box. Allow New Devices: Allows you to change the access control used by the SpeedTouch™.
Chapter 4 Basic Configuration WPA-PSK The SpeedTouch™ supports WPA-PSK which has 3 improvements regarding to WEP: Authentication via a 4-way handshake to check whether the Pre-Shared Keys (PSKs) are the same. Stronger encryption types: Temporal Key Integrity Protocol (TKIP) (default): Instead of using a fixed WEP key, TKIP uses in pairs temporary session keys which are derived from the PSK during the 4-way handshake. For each packet it uses a different key.
Chapter 4 Basic Configuration 4.6.6 Configuring WDS What is WDS The Wireless Distribution System (WDS) allows you to extend the range of your wireless network by introducing one or more WDS-enabled devices into your wireless network. ! Accessing the WDS page You can only establish WDS links with WDS enabled devices. To access the WDS pages on the SpeedTouch™: 1 On the left menu, click Office Network. 2 Under Wireless, click the Access Point you want to configure for WDS.
Chapter 4 Basic Configuration 4.6.7 Interfaces Interfaces overview 96 This page gives you an overview of the interfaces used on your SpeedTouch™. If you want to know more on the network settings of a specific interface, click the name of the interface you want to view. E-DOC-CTC-20050429-0104 v1.
Chapter 4 Basic Configuration 4.6.8 Interface Settings Overview Configure The Overview page gives you an overview of the current interface settings. The Configure page allows you to: Change the IP address settings of the SpeedTouch™. Change the DHCP IP address pool settings. Before changing the DHCP pools, make sure that at least one IP address of the SpeedTouch™ uses the same subnet as the IP addresses in the DHCP pools.
Chapter 4 Basic Configuration 4.6.9 DHCP Pool DHCP Pool Accessing the DHCP Pool page This page allows you to create/change a DHCP pool. Proceed as follows: 1 On the Office Network menu, click Interfaces. 2 Click on the name of the interface of which you want to change the DHCP pool settings. 3 Click Configure. 4 Under DHCP Pools click: Add if you want to add a new DCHP pool. Edit if you want to edit an existing DHCP pool. Delete if you want to delete an existing DHCP pool.
Chapter 4 Basic Configuration The DHCP Pool page Following settings are available for configuration: Interface: The SpeedTouch™ interface for which the DHCP pool applies. Start Address: The start IP address of the DHCP server’s address pool. End Address: The end IP address of the DHCP server’s address pool. Both the start and end IP address define the IP address range used by the DHCP server to assign leases. Subnet Mask: The subnet mask of the DHCP server’s address pool.
Chapter 4 Basic Configuration 100 E-DOC-CTC-20050429-0104 v1.
Chapter 5 Expert Configuration 5 Expert Configuration Introduction The SpeedTouch™ Expert Mode pages allows for advanced configuration and maintenance of your SpeedTouch™ device. While the Basic pages are mainly constructed to allow you to overview and diagnose the running product and its configuration, the Expert Mode pages have been designed to allow in-depth configuration of every aspect of your SpeedTouch™. Web GUI overview E-DOC-CTC-20050429-0104 v1.
Chapter 5 Expert Configuration Expert Mode navigation The Navigation and notification area displays the current user and the site navigator, as well as notification messages, if applicable. In addition, following action buttons are always available on every page: Click ... To ... Save All force a save of the current configuration of your SpeedTouch™. CLI access the complete SpeedTouch™ Command Line Interface in a graphical way. Help open the SpeedTouch™ help pages.
Chapter 5 Expert Configuration 5.1 Home Overview The Expert Mode Home page is in fact the same as the SpeedTouch™ Home page in Basic Mode; it provides an instant overview of all aspects of your SpeedTouch™ configuration and operational status. For more information, see Home (of Basic Configuration web interface). E-DOC-CTC-20050429-0104 v1.
Chapter 5 Expert Configuration 5.2 SpeedTouch™ Overview 104 The SpeedTouch™ menu consists of the following topics: Click ... To ... Easy Setup start the embedded Easy Setup wizard. System Information view important SpeedTouch™ information. Connections start/stop PPP connection sessions. Diagnostics view detailed system and configuration information of the SpeedTouch™ and perform IP connectivity checks on WAN connections. Syslog view/configure the SpeedTouch™ system logging engine.
Chapter 5 Expert Configuration 5.2.1 Easy Setup Introduction Click Easy Setup to start the SpeedTouch™ Easy Setup wizard. The Easy Setup wizard provides an easy way to prepare the SpeedTouch™ for Internet connectivity.
Chapter 5 Expert Configuration 5.2.2 System Information Overview Diagnostics The System Information page is the SpeedTouch™ expert start page. It consists of four sections: Diagnostics DSL Line Info Configuration System Select Diagnostics to view the results of the System Self Test, LAN connectivity and DSL synchronisation test: If result is... Then ... the overall status of the particular item is healthy. an error situation has been detected for that item.
Chapter 5 Expert Configuration System Select System to view some important system information of the SpeedTouch™. The System table lists the SpeedTouch™’s: Product Name Physical Address. This worldwide unique hardware address is also called Medium Access Control (MAC) address. Software Release Board Name Serial Number Product Code Most of the information is also listed on the identification label on the bottom of the SpeedTouch™. E-DOC-CTC-20050429-0104 v1.
Chapter 5 Expert Configuration 5.2.3 Connections Overview The Connections page allows you to start and stop PPP connection sessions. All existing PPP connections are listed in the Connections table. If no PPP connections have been defined, this table is empty.
Chapter 5 Expert Configuration 5.2.4 Diagnostics Overview The Diagnostics page provides in-depth information, counters and statistical data on the SpeedTouch™ system settings, and its LAN and WAN connections. The diagnostics are broken down into three expandable categories: System LAN WAN Per category an overall status is displayed: If the status is ... Then ... the overall status of the particular category is healthy. an error situation has been detected for that category.
Chapter 5 Expert Configuration 5.2.5 Syslog Overview Messages The Syslog page consists of two sections: Messages Configuration This section allows to overview system log and alert messages your SpeedTouch™ generated during operation. System log messages are used to provide a historical overview of events, errors, and messages generated during SpeedTouch™ operation.
Chapter 5 Expert Configuration To change or delete a destination: 1 Select the applicable interface 2 If needed, make your changes and click: New to add a new destination with the new settings next to the existing one. Apply to apply the changes to the existing destination. Delete to remove the destination from the list of destinations. Click Deactivate to withdraw all forwarding of syslog messages for all destinations; to re-enable forwarding of syslog messages, click Activate.
Chapter 5 Expert Configuration 5.2.6 System Update Overview System configuration The System Update page features all means for management and maintenance of your SpeedTouch™. It consists of two sections: System configuration System Upgrade The System Configuration section allows you to manage locally stored system files. Select: Upload system files Upload File to upload a system file to the SpeedTouch™. See “ Upload system files” on page 112 for more information.
Chapter 5 Expert Configuration To upload system files: 1 Click Browse to specify the file on your local drive you wish to upload. 2 Click Upload to upload the system file to your SpeedTouch™. Each file requires an amount of memory. Make sure to limit the number of files to the minimum. ! Manage configuration files This table allows you to view configuration files that are currently stored on your SpeedTouch™.
Chapter 5 Expert Configuration System Upgrade The System Upgrade section allows you to manage your SpeedTouch™’s system software and upload or apply a new system software. For extended management reasons and roll-back scenarios your SpeedTouch™ provides storage room for two system software packages: the active system software the SpeedTouch™ is currently running and the passive one.
Chapter 5 Expert Configuration 5.2.7 SpeedTouch™ Services Overview The SpeedTouch™ Services page allows you to view and configure all services that are currently configured on your SpeedTouch™. The purpose of this page is to centralise the management of all SpeedTouch™ embedded Services and Applications, or otherwise stated, all internal modules and engines of the SpeedTouch™ that accept, relay or initiate IP traffic.
Chapter 5 Expert Configuration Edit SpeedTouch™ service properties Editing SpeedTouch™ services might be useful in cases where you want to hide/ protect the service by deviation from the typical service settings or restricting access from/to interfaces. However; ! Do not edit SpeedTouch™ system services unless specifically needed. To edit a SpeedTouch™ system service: 1 Select the service.
Chapter 5 Expert Configuration SpeedTouch™ service types E-DOC-CTC-20050429-0104 v1.0 The SpeedTouch™ service can be of following type: Type Indicates a SpeedTouch™ service that... Client is the originator of an IP connection (source IP packets). Server is the responder of an IP connection (listening to IP packets). Peer can be an originator or a responder of an IP connection. Proxy is a responder on the LAN side and originator on the WAN side of the SpeedTouch™.
Chapter 5 Expert Configuration 5.2.8 SNTP Overview The Simple Network Time Protocol (SNTP) web page allows you to configure the SpeedTouch™ real-time clock. The page contains two sections: SNTP Client Manual Selecting Manual immediately disables the SpeedTouch™ SNTP client. As a consequence the SpeedTouch™ real-time clock will no longer be periodically synchronised with an Internet time server.
Chapter 5 Expert Configuration 5.2.9 SLA Overview The Service Level Agreement (SLA) page allows you to view and configure ping and traceroute tests. The page contains two sections: Ping Select Ping to view/configure and perform ping tests. Select Traceroute to view/configure and perform traceroute tests. The Ping table provides a list of configured ping test entries. By default no ping tests are configured. To add a ping test see Add/delete a ping test.
Chapter 5 Expert Configuration Ping tests and results To start/stop a ping test: 1 Select the ping test entry. 2 Click: Activate to start the ping test. Deactivate a ping test that is currently running. To view the results of the ping test: 1 Select the ping test entry, if needed. 2 Click Result. To overview a history of ping tests: Traceroute 1 Select the ping test entry. 2 Click History. The Traceroute table provides a list of configured traceroute test entries.
Chapter 5 Expert Configuration Add/delete a traceroute test To add a traceroute test entry: 1 Click New (if an entry is currently selected, click Cancel first). 2 Type a name for the traceroute test entry. 3 Type the host name or IP address of the target to traceroute. 4 Click Apply. To delete a traceroute test: Modify traceroute test properties traceroute tests and results 1 Select the traceroute test entry to delete. 2 Click Delete.
Chapter 5 Expert Configuration 5.2.10 Add-on Overview Some of the SpeedTouch™'s extended functionalities require a software activation key to enable the corresponding software module. To acquire a software activation key for activating a SpeedTouch™ software module, proceed as follows: 1 Click the name of the software module you intend to activate. This link will forward you to the SpeedTouch™ software activation key web server.
Chapter 5 Expert Configuration 5.3 IP Router Overview E-DOC-CTC-20050429-0104 v1.0 The IP Router menu consists of the following topics: Click ... To ... IP Addresses view/configure the IP addresses assigned to any of the SpeedTouch™ interfaces. Expressions view/configure interface, or IP, or Service related expressions. Classification view/configure packet classification and handling. IP Routing view/configure the SpeedTouch™ IP forwarding and routing table.
Chapter 5 Expert Configuration 5.3.1 IP Addresses Overview The IP address table shows all IP addresses configured on any of SpeedTouch™’s interfaces.
Chapter 5 Expert Configuration 5.3.2 Expressions Overview Expressions are used in rules for source and destination interface, source and destination IP address(es) (ranges) and services. The Expressions page consists of three sections: Interface IP Service Expressions are also used by the SpeedTouch™ Stateful Inspection Firewall. Interface The Interface section bundles all expressions that express a relation based on Interfaces.
Chapter 5 Expert Configuration IP The IP section bundles all expressions that express a relation based on IP addresses. The Expressions table provides following information per expression: Adding an IP related expression The Name of the expression A Summary of the expression’s configuration. For more detailed information you can expand the expression (click ). To add a new IP related expression: 1 Click New. 2 In the IP Expressions Properties table: Type a Name for the expression.
Chapter 5 Expert Configuration 5.3.3 Classification Overview Labels The Classification page consists of three section: Labels, providing a list of existing packet classification labels and abilities to add/modify or delete packet classification label entries. Routing Rules allow you to associate a routing label (used in IP Routing) to a data flow by means of classification rules.
Chapter 5 Expert Configuration Routing Rules The Routing Rules section provides an overview of the existing routing rules. Proceed as follows to create a new rule: 1 Click New to create a new rule. 2 Fill in all the fields. 3 IP QoS Rules Index: The index of the label rule. Name: The name of the rule. Label: The label allows to identify packets with matching criteria. If such a packet arrives it is “labelled” with a packet classification label. Still no packet classified routing is done.
Chapter 5 Expert Configuration 5.3.4 IP Routing Overview The IP Routing table presents the current content of the SpeedTouch™ Routing Information Base. It contains all routes to all possible destinations and is consulted by the SpeedTouch™ any time prior to sending or forwarding any packets. Similar to the IP address table, a number of IP Routes are pre-configured. Other routes are either added via adding an IP address manually, or via the address negotiation of a Packet Service connection session, e.g.
Chapter 5 Expert Configuration 5.3.5 RIP Overview Configuration Interfaces Neighbours 130 The RIP web page contains three tabs: Configuration Interfaces Neighbours The Configuration section allows you to enable/disable the SpeedTouch™ RIP functionality and configure the some basic RIP settings.
Chapter 5 Expert Configuration 5.3.6 NAT Overview Interfaces The NAT menu consists of following sections: Interfaces Mappings Templates The Interface page allows you to enable/disable NAPT on a specific interface. Proceed as follows to enable/disable an interface: Mappings 1 Select the interface that has to be enabled/disabled 2 Click Save All to make the settings permanent.
Chapter 5 Expert Configuration Creating a NAT mapping Templates Proceed as follows to create a address translation mapping: 1 Click New to create a new map. 2 Select or fill in all the fields (see above). 3 Click Apply. The Template page allows you to create a NA(P)T template. Depending on your needs following fields are available: Interface: The name of the IP interface that needs to be NAT-ed. Group: The IP interface group scope for this template.
Chapter 5 Expert Configuration 5.3.7 IP QoS Definition Quality of Service is the ability for an application to obtain the network service it requires for successful operation. Nowadays the total amount of data traffic increases, while new types of data emerge, like: voice data, video data, audio data. These new types of data pose new requirements for data transport, e.g. low latency, low data loss… To meet these requirements, the entire network must ensure them via a connection service guarantee.
Chapter 5 Expert Configuration Configuration The Configuration page allows you to configure IPQoS for a given destination interface for the IPQoS queues instantiation. When enabling or disabling IPQoS, take the following into account: if the WAN interface (for example PPPoA, IPoA,...) is detached at the time of enabling/disabling IPQoS, then the WAN interface has to be attached in order for the enabling/disabling of IPQoS to take effect.
Chapter 5 Expert Configuration 5.4 Connections Overview E-DOC-CTC-20050429-0104 v1.0 The Connections menu consists of the following topics: Click ... To ... ATM view/configure SpeedTouch™’s ATM interfaces. Routed PPPoE view/configure the Routed PPP over Ethernet (PPPoE) Internet services. Routed PPPoA view/configure the Routed PPP over ATM (PPPoA) Internet services. Routed PPPoI view/configure the Routed PPP over ISDN (PPPoI) Internet services.
Chapter 5 Expert Configuration 5.4.1 ATM Overview Phonebook The ATM page consists of following sections: Phonebook QoS Book Interfaces The SpeedTouch™ Phonebook is a repository for ATM connectivity information. A number of pre-configured entries may already reside in the SpeedTouch™ Phonebook. The Phonebook: Adding a phonebook entry Connection Service Name Virtual Channel Identifiers (VPI and VCI) 136 Allows you to use named connections.
Chapter 5 Expert Configuration It is the responsibility of the network operator to provide end-to-end connectivity throughout the network on these virtual channels. Due to regional differences or because of the specific policy of your local operator, specific VPI/VCI values may be required. In this case, the network operator, ISP or corporate administrator will provide the correct values. The VPI can range from 0 to 15, VCI from 32 .. 511. If your SpeedTouch™ is equipped with an ATMF-25.
Chapter 5 Expert Configuration 5.4.2 Routed PPPoE Introduction Creating a Routed PPPoE connection entry Additional configuration The Routed PPPoE configuration page allows you to add new Routed PPPoE, or Routed PPPoE Relay connection entries or to change settings of existing entries. To add a Routed PPPoE connection entry: 1 Click New. 2 In the Interface box, type a unique interface name (different from the MER interface name).
Chapter 5 Expert Configuration Other This window holds miscellaneous information and configuration possibilities. Following fields are available: Mode: A PPP connection can be established in three ways: Manually: You have to press the Dial-In button of a particular connection. Always-On: The SpeedTouch™ automatically tries to establish PPP connections. On-Demand: A PPP connection is triggered by specific frames arriving at the Ethernet port.
Chapter 5 Expert Configuration 5.4.3 Routed PPPoA Introduction Creating a Routed PPPoA connection entry Additional configuration The Routed PPPoA configuration page allows you to add new Routed PPPoA connection entries or to change settings of existing entries. To add a Routed PPPoA connection entry: 1 Click New. 2 In the Interface box, type a unique interface name (different from the MER interface name).
Chapter 5 Expert Configuration Other This window holds miscellaneous information and configuration possibilities. Following fields are available: Mode: A PPP connection can be established in three ways: Manually: You have to press the Dial-In button of a particular connection. Always-On: The SpeedTouch™ automatically tries to establish PPP connections. On-Demand: A PPP connection is triggered by specific frames arriving at the Ethernet port.
Chapter 5 Expert Configuration 5.4.4 Routed PPPoI Availability Introduction Creating a Routed PPPoI connection entry The ISDN modem is only fully functional after activating the ISDN software module with the ISDN software module activation key. For more information, see “5.2.10 Add-on” on page 122. The Routed PPPoI configuration page allows you to add new Routed PPPoI connection entries or to change settings of existing entries. To add a Routed PPPoI connection entry: 1 Click New.
Chapter 5 Expert Configuration Other This window holds miscellaneous information and configuration possibilities. Following fields are available: Mode: A PPP connection can be established in three ways: Manually: You have to press the Dial-In button of a particular connection. Always-On: The SpeedTouch™ automatically tries to establish PPP connections. On-Demand: A PPP connection is triggered by specific frames arriving at the Ethernet port.
Chapter 5 Expert Configuration 5.4.5 Bridged Ethernet Overview Bridged Ethernet The Bridged Ethernet page consists of following sections: Bridged Ethernet VLAN The Bridged Ethernet page allows you to configure the SpeedTouch™ for IEEE802.1D Transparent Bridging, which equally may include preparing it for Bridged PPPoE. Next to transparent bridging, the SpeedTouch™ also features full VLAN awareness, and as such allow Ethernet interface grouping or VLAN-tag based forwarding.
Chapter 5 Expert Configuration Add a new Bridge port Proceed as follows to add a new port to the Ethernet Bridge: 1 Click New under the Bridge Ethernet overview table 2 In the Interface box, type a unique interface name; in the Destination list, select the interface you want to use for this connection. 3 Mark the Multicast filter checkbox if you wish to filter out multicast streams on this interface.
Chapter 5 Expert Configuration VLAN interface configuration Proceed as follows to add or remove Bridged Ethernet interfaces for a certain VLAN: 1 Select the VLAN you wish to edit. 2 A listing of all bridge interfaces will appear, each followed by a drop-down list. Change the value of the drop-down list to add or remove interfaces from this VLAN: 3 146 (none), which means that this interface is not a member of the selected VLAN.
Chapter 5 Expert Configuration 5.4.6 Routed Ethernet Introduction The Routed Ethernet web page allows you to add and modify Routed Ethernet interfaces. Routed Ethernet interfaces can be used for creating end-to-end MAC Encapsulated Routing (MER) connections, or for creating a destination interface to create Routed PPPoE connections on, or to apply a routed PPPoE Relay scenario. E-DOC-CTC-20050429-0104 v1.
Chapter 5 Expert Configuration 5.4.7 Routed IPoA Creating a new Routed IPoA Ethernet Interface To add a new Routed IPoA Ethernet interface, proceed as follows: 1 Click New. 2 Following fields become available: Interface Name: Is a name that has local significance only and allows to reference a particular Routed IPoA interface Local IP Address: Is an IP address that must be configured on the local Routed IPoA Ethernet interface and is provided by your ISP or system administrator.
Chapter 5 Expert Configuration 5.4.8 PPTP-to-PPP Relay Overview The PPTP-to-PPP Relay, referred to as "Relay" further in this section, interacts with a PPTP tunneling application installed on the locally attached computers, for example Microsoft's Dial-Up Networking. A typical user-relay interaction scenario is as follows: A PPTP Tunnelling application is started on one of the locally attached computers.
Chapter 5 Expert Configuration 5.4.9 Virtual LAN Concept The concept of VLAN was introduced as a way to solve many of the issues of a large Layer 2 environment. It controls the traffic on a physical LAN. The physical LAN is partitioned into multiple virtual LANs. Each VLAN is assigned a number, called the VID, that identifies it uniquely within the network. Traffic between these systems stays bottled up within their VLAN.
Chapter 5 Expert Configuration 5.5 Local Networking Overview E-DOC-CTC-20050429-0104 v1.0 The Connections menu consists of the following topics: Click ... To ... DHCP View/configure the SpeedTouch™ DHCP settings. DNS View/configure the SpeedTouch™ DNS settings. Managed Switch View/configure the SpeedTouch™ Managed Switch. Wireless View/configure the SpeedTouch™ wireless access point settings.
Chapter 5 Expert Configuration 5.5.1 DHCP Overview DHCP Server The DHCP web page offers three tabs to configure the SpeedTouch™ 's DHCP functionality: DHCP Server: To configure the general behaviour of the SpeedTouch™ 's DHCP server. DHCP Relay: To configure the SpeedTouch™ DHCP relay. DHCP Client: To configure the SpeedTouch™ DHCP client. The DHCP server configuration is split up in three sections: Server Config: To configure the SpeedTouch™ DHCP server ‘master’ settings and behaviour.
Chapter 5 Expert Configuration Server Leases In case the SpeedTouch™ DHCP server is running this table holds all leases which are assigned by the DHCP server to (accepted) DHCP clients. Following lease parameters are shown : Client ID: The MAC address of the DHCP client. Address: The IP address leased by the DHCP client. Pool: The DHCP server address pool the lease IP address is taken from. TTL: The DHCP server lease's Time To Live (in seconds).
Chapter 5 Expert Configuration Address Pools One or more disjunctive DHCP server address pools can be created per existing SpeedTouch™ interface using the Address Pool table. The first address pool displayed in the table has the highest priority for a certain interface. If you select one of the address pools, following fields become available: Name: The name of the DHCP server's address pool. Interface: The SpeedTouch™ interface for which the address pool applies.
Chapter 5 Expert Configuration DHCP Relay The DHCP relay tab allows you to add/delete and overview SpeedTouch™ 's DHCP relay interfaces. The DHCP relay configuration is split up in two sections: Relay Config Relay Config To add/delete and configure a DHCP relay server on a certain interface Relay Interfaces To enable/disable and define the behaviour of the DHCP relay agent per configured interface.
Chapter 5 Expert Configuration DHCP Client Dynamic interfaces are created and managed by means of the DHCP Client table. Following fields are listed in the DHCP Client table: Interface: The name of the SpeedTouch™ logical interface for which this DHCP client applies The Address column shows the IP address assigned to the interface given in the first column. The State column shows the current state of the dynamic interface.
Chapter 5 Expert Configuration 5.5.2 DNS Overview DNS is short for Domain Name System. It is a network functionality that allows network members to use host names rather than IP addresses for referencing networked computers. The DNS web page consists of two sections: Configuration Configuration Hostname Table In addition to the host name, a local computer needs the DNS domain name to construct a fully qualified name. By default the SpeedTouch™ DNS's domain name is lan.
Chapter 5 Expert Configuration 5.5.3 Managed Switch Overview Your SpeedTouch™ is equipped with a four-port 10/100Base-T auto-sensing MDI/ MDI-X Ethernet switch. Each physical Ethernet port of the switch can be managed individually for extended networking control and monitoring purposes. The Managed Switch page consists of two sections: Managed Ethernet Switch 158 Managed Ethernet Switch provides an overview of each individual Ethernet port.
Chapter 5 Expert Configuration Mirror Configuration Port mirroring allows monitoring from one port (called mirrored port) to another port (called mirror capture port). This functionality allows any port's Ingress and/or Egress traffic to be monitored to a pre-defined "mirror capture port". Depending on your configuration you can mirror (from mirror port to mirror capture port): E-DOC-CTC-20050429-0104 v1.0 The outgoing traffic The incoming traffic Both incoming and outgoing traffic.
Chapter 5 Expert Configuration 5.5.4 Wireless Overview The SpeedTouch™ IEEE802.11g compliant Wireless LAN (WLAN) interface allows you to share its high-speed Internet connection with multiple networking clients in a local network, without needing to (re-)wire your home. The SpeedTouch™ acts as a wireless Access Point (AP), connecting wireless clients and transferring data between them.
Chapter 5 Expert Configuration Access point settings This section provides an overview and allows you to configure the basic wireless networking parameters for your SpeedTouch™ wireless access point. Following wireless access point settings can be viewed or configured: E-DOC-CTC-20050429-0104 v1.0 Network Name (SSID): The network name, also known as Service Set ID (SSID). For more information, see “ Network Name (SSID)” on page 162.
Chapter 5 Expert Configuration Network Name (SSID) The WLAN's 'radio' link is a shared medium. As no physical connection exists between the SpeedTouch™ and wireless clients, a name must be given to allow unique identification of your WLAN radio link. This is done by the Network Name, also known as Service Set ID (SSID). Wireless clients must be configured for the same Network Name in order to be able to communicate with other clients on the (W)LAN - via the SpeedTouch™ wireless access point.
Chapter 5 Expert Configuration Enable/disable the wireless interface To disable your wireless interface: 1 Clear wireless interface enabled. 2 Click Apply to immediately apply your changes. ! All your wireless clients will be disconnected! You can also disable your wireless interface by pressing the front panel button for 10 seconds. When the WLAN led is extinguished, the interface is disabled. To enable the wireless interface: 1 Select Wireless interface enabled.
Chapter 5 Expert Configuration WEP The Wired Equivalent Privacy (WEP) algorithm is used to protect wireless communication from eavesdropping. WEP relies on a secret key that is shared between the wireless client (e.g. a laptop with a wireless ethernet card and the SpeedTouch™. The fixed secret key is used to encrypt packets before they are transmitted. I.e.
Chapter 5 Expert Configuration Access Control Wireless client access control allows to authorize or explicitly inhibit access between specific wireless clients and the SpeedTouch™ wireless access point based on the wireless client's MAC address. The Access Control tab allows you to manage the SpeedTouch™ Access Control List (ACL). By default New stations allowed automatically is selected.
Chapter 5 Expert Configuration Associated stations The Associated Stations tab allows you to overview the currently associated clients. To add an associated station to the access control list: 1 Select the entry you want to explicitly add to the ACL. Associated stations that are not present in the ACL yet, are identified by the name Not Registered (ACL). 2 To change the access rights for this station, click Access Control. 3 Change the name of the station (optional but recommended).
Chapter 5 Expert Configuration 5.6 Firewall Overview E-DOC-CTC-20050429-0104 v1.0 The Firewall menu consists of the following topics: Click ... To ... Expressions view/configure interface, or IP, or Service related expressions. For more information, see “5.3.2 Expressions” on page 125. Policy view/configure the SpeedTouch™ Stateful Inspection Firewall security level and its policies. Log view log messages for SpeedTouch™ firewall events.
Chapter 5 Expert Configuration 5.6.1 Policy Firewall levels 168 The Level list allows you to choose between the following level: Disabled: All traffic is allowed to pass through your SpeedTouch™. Game and Application sharing is allowed by the firewall. BlockAll: Use this Security Level to block all traffic from and to the Internet. Game and Application sharing is not allowed by the firewall.
Chapter 5 Expert Configuration Buttons Click: Customize... to create a new firewall level starting from the selected firewall level. For more information, see “ Creating a firewall rule” on page 170. Set Active to activate the selected firewall rule. ! Loose UDP tracking To save the new configuration, click Save All. If this check box is: Selected: The source port of the original UDP connection is opened for all hosts which want to connect to this port.
Chapter 5 Expert Configuration Creating a firewall rule Proceed as follows to create a new security level and to add rules: 1 Select one of the six security levels. 2 Click Customize. 3 Type name and description for the new security level and click Apply. 4 Click New to add a rule. 5 Fill in all the fields. Index: The index of the firewall rule. The firewall hierarchically goes through the rules, starting from rule 1.
Chapter 5 Expert Configuration 5.6.2 Log Introduction E-DOC-CTC-20050429-0104 v1.0 The Log page allows you to view log messages when: a firewall rule is hit. the firewall is enabled or disabled. the firewall level is changed. a firewall rule is created. a firewall rule is modified. a firewall rule is deleted.
Chapter 5 Expert Configuration 5.7 VPN Availability Overview 172 The VPN feature is only available if you activated the VPN software module. For more information, see “5.2.10 Add-on” on page 122. The VPN menu consists of following items Click ... To ... LAN to LAN connect your LAN with a remote LAN through an IPSec VPN tunnel. VPN Client set up a connection between the SpeedTouch™ and a remote VPN server. VPN Server set up the SpeedTouch™ as a VPN server.
Chapter 5 Expert Configuration 5.7.1 LAN to LAN Tabs Configuration procedure E-DOC-CTC-20050429-0104 v1.0 The LAN to LAN page consists of two tabs. Select: Remote Gateway Address Known as the starting page when the SpeedTouch™ must be able to initiate a VPN connection. Remote Gateway Address Unknown as the starting page when the SpeedTouch™ only needs to have responder capability.
Chapter 5 Expert Configuration 5.7.2 VPN Client The VPN Client page Configuration procedure 174 The VPN client in the SpeedTouch™ can replace a software VPN client installed on a computer. You can use it for example to connect from your home to your employer’s corporate network for tele-working. The VPN Client page allows you to configure a VPN client that functions in Initiator mode. This means that the VPN client takes the initiative to set up a secure connection to a remote VPN server.
Chapter 5 Expert Configuration 5.7.3 VPN Server The SpeedTouch™ as VPN Server In a VPN client-server scenario, the VPN server is always the responder in the IKE negotiations. Various VPN clients can dial in to a VPN server, since it supports multiple simultaneous VPN connections. A VPN server does not know a priori which remote Security Gateway will attempt to set up a VPN connection. In time, new users may join the VPN.
Chapter 5 Expert Configuration 5.7.4 Certificates Certificates pages The Certificates pages allow you to manage your certificates. Secure Storage page This page shows the list of certificates stored in the SpeedTouch™. Request Import page This page allows importing new certificates from a Certificate Authority into the SpeedTouch™. 176 CRL page This page allows managing the use of Certificates Revocation Lists. CEP page This page allows configuring the Certificates Enrollment Protocol settings.
Chapter 5 Expert Configuration 5.7.5 Advanced When to use The Advanced VPN menu gives access to two main pages where the complete IPSec configuration can be done. These pages are component-oriented, as opposed to the application-oriented pages described in “5.7.1 LAN to LAN” on page 173, “5.7.2 VPN Client” on page 174 and “5.7.3 VPN Server” on page 175. Componentoriented means that a number of components are constructed and subsequently combined.
Chapter 5 Expert Configuration 5.7.6 Debug Status page Statistics page Logging page This page shows the status of the IKE Security Association (Phase 1) and the IPSec Security Association(s) (Phase 2). For an operational VPN connection, both an IKE Security Association and an IPSec Security Association should be active. This page shows the amount of traffic carried over the IKE Security Association (Phase 1) and the IPSec Security Association(s) (Phase 2).
Chapter 5 Expert Configuration 5.8 SIP PBX Availability The VPN feature is only available if you activated the SIP PBX software module. For more information, see “5.2.10 Add-on” on page 122. SpeedTouch™ SIP PBX The SpeedTouch™ has a key role in the enhancement of Voice over IP services for corporations, universities or enterprises.
Chapter 5 Expert Configuration Location Service Call Logging The Location Service page allows you to: View the registered users. Add new SIP users. All inbound and outbound SIP sessions that cross the multi-media SIP PBX can be monitored from the SpeedTouch™web interface. Both successful and failed calls will be shown. This is a useful tool to supervise the SIP communications involving your LAN User Agents. The Syslog Settings tab allows you to log SIP call information to the syslog.
Chapter 6 Software Keys 6 Software Keys Introduction A Software Key is a tool to disclose or activate services or software modules.
Chapter 6 Software Keys 3 Select the desired software module to open the registration web site on the Internet. Complete the form to request a new software Key. 4 Select the Request Software Key button to proceed. As a result you will get a text box with the key in it. 182 5 Copy the key and past it into the Software Activation Code Input Display and click the Add button. 6 Click the Restart button, to restart the SpeedTouch™and activate the software module.
Chapter 7 Software Upgrade 7 Software Upgrade Introduction System software upgrades availability System software packages and security This chapter describes how to upgrade the SpeedTouch™ system software or firmware. For the availability of new system software version packages you can: Click the SpeedTouch Maintenance link, available on the Setup CD menu. Go to the embedded Update page. Check for SpeedTouch™ upgrades at http://www.speedtouch.com/upgrade.
Chapter 7 Software Upgrade 7.1 Embedded Update Page Introduction Procedure From a remote server This procedure is OS independent and supports roll-back scenarios. Your SpeedTouch™ provides storage room for two system software packages: the active system software the SpeedTouch™ is currently running and a passive package. A switch over from the one package to the other can be performed. Proceed as follows: 1 Go to the embedded web pages. 2 In the menu select SpeedTouch > Update.
Chapter 7 Software Upgrade From a PC You can upgrade your SpeedTouch™ from a PC. This procedure is done in steps. You will download the software image to your PC first. You can choose another moment to upload the software to your SpeedTouch™. 1 2 3 4 E-DOC-CTC-20050429-0104 v1.0 To download the latest software version: 1 Click SpeedTouch Support Site. 2 On the SpeedTouch™ Support Site, download the software. Remember the location where you save this software.
Chapter 7 Software Upgrade 7.2 Upgrade Wizard on Setup CD Introduction The procedures described in this section are valid only in case: You run an MS Windows Operating System or Mac OS X. Your SpeedTouch™ and computer are properly connected through Ethernet. ! It is NOT possible to upgrade your SpeedTouch™ over a wireless connection. During the upgrade procedure in most cases configuration settings are backed up by the wizard and restored after uploading the system software.
Chapter 7 Software Upgrade Upgrade procedure 1 2 In the Welcome to the SpeedTouch Upgrade Wizard window, click Next. The SpeedTouch™ Software License Agreement window appears. You must accept before continuing. Click Yes to accept. If you accepted this License Agreement in a previous upgrade, this window will not be shown. 3 The SpeedTouch™ Upgrade Wizard will search for the SpeedTouch™ on the network. A progress bar is displayed.
Chapter 7 Software Upgrade The following window shows the system software version currently active on the SpeedTouch™ as well as one or more system software versions available on the CD: 6 For more information on a found software version, click Firmware Details. Select the appropriate system software version and click Next. If your Service Provider has included a separate disk with dedicated upgrade system software, click Have Disk to navigate to the location of the appropriate file.
Chapter 7 Software Upgrade 7.3 Upgrade via a BOOTP/TFTP Server SpeedTouch™ system software management The SpeedTouch™ system software is based on BOOTP, a standard mechanism used for booting diskless stations. You can force the SpeedTouch™ in BOOTP mode, allowing a BOOTP/TFTP server to manage the SpeedTouch™ file system, and submit upgrade files to it.
Chapter 7 Software Upgrade Procedure To upgrade/restore the SpeedTouch™ system software: 1 In a preliminary step, make sure that a BOOTP server is readily installed on the computer from which you intend to perform the system software upgrade. 2 Configure the BOOTP server to use the SpeedTouch™ system software image file in its reply to BOOTP requests from the SpeedTouch™ you want to upgrade.
Chapter 8 Troubleshooting 8 Troubleshooting Introduction This chapter suggest solutions for problems you may encounter while installing or configuring your SpeedTouch™. If the suggestions do not resolve the problem, look at the support pages on http:// www.speedtouch.com/support or contact your service provider. For Internet connection troubleshooting, refer to the provided Installation and Setup Guide. E-DOC-CTC-20050429-0104 v1.
Chapter 8 Troubleshooting 8.1 General SpeedTouch™ Troubleshooting SpeedTouch™ does not work SpeedTouch™ unreachable If none of the LEDs light up, make sure that: The SpeedTouch™ is plugged into a power socket outlet. You are using the correct power supply for your SpeedTouch™ device, that is 18V AC. The power on the SpeedTouch™ is turned on via the rocker switch on the back panel.
Chapter 8 Troubleshooting 8.1.1 Wired Ethernet Troubleshooting LAN LED does not light up E-DOC-CTC-20050429-0104 v1.0 Make sure that: The LAN cable is securely connected to the 10/100Base-T port. You are using the correct cable type for your Ethernet equipment, that is UTP CAT5 with RJ-45 connectors.
Chapter 8 Troubleshooting 8.1.2 Wireless Ethernet Troubleshooting Not able to connect wireless clients No wireless connectivity Poor wireless connectivity or reach 194 Check following: In case registration is enabled, you must press the 'Association' button to register the wireless client or search for wireless devices via the embedded web pages. Make sure the SpeedTouch™ Association Control List is not locked. You can check this on the web pages.
Chapter 8 Troubleshooting 8.1.3 Upgrade Troubleshooting Introduction Upgrade via web pages While upgrading your SpeedTouch™ via the Upgrade Wizard on the web pages or on the Setup CD, you might encounter one of following problems. One of following messages might appear: Update from remote server: Message Due to Failed to retrieve new software version from the support site. Try again later. The file does not exist, meaning there is no newer software release. Loss of connectivity.
Chapter 8 Troubleshooting Upgrade via Setup CD If the Upgrade Wizard in step 4, as described in “ Upgrade procedure” on page 187, does not find any SpeedTouch™ on the network, an error window will appear, stating your SpeedTouch™ has not been found. In this case check that: The SpeedTouch™ is turned on and fully initialised. Your PC is correctly connected to the SpeedTouch™. Your PC has a valid IP address. To check this in MS Windows: 1 In the Windows task bar, click Start. 2 Select Run...
Chapter 8 Troubleshooting 8.2 UPnP™ on Windows XP Systems SpeedTouch™ not detected by UPnP™ or IGD Control Client Adding UPnP™ Check on following: Make sure the UPnP™ and Internet Gateway Device Control Client Networking components are added to your MS Windows XP system. Your computer doesn’t support UPnP™ if you run an operating system other than MS Windows XP and MS Windows Millennium. Make sure that UPnP™ is not disabled in the SpeedTouch™ web page; see “4.5.
Chapter 8 Troubleshooting Adding IGD Discovery and Control Your MS Windows XP system is able to discover and control Internet Gateway Devices (IGD), like the SpeedTouch™ on your local network. Therefore it is recommended to add the IGD Discovery and Control client to your system. Proceed as follows: 1 On the Windows task bar, click Start. 2 Select (Settings >) Control Panel > Add or Remove Programs. 3 In the Add or Remove Programs window, click Add/Remove Windows Components.
Chapter 8 Troubleshooting 8.3 Reset to Factory Defaults Resetting your SpeedTouch™ You might consider a reset to factory defaults as described below. ! Be aware that a reset to factory defaults will revoke all configurational changes you made to the SpeedTouch™. You can choose between: Hardware reset Software reset A reset to factory default settings deletes the configuration profile settings. Therefore, after the reset, a reconfiguration of your SpeedTouch™ will be needed.
Chapter 8 Troubleshooting Software reset 200 Proceed as follows: 1 Go to the SpeedTouch™ web pages. 2 In the menu select SpeedTouch > Configuration. 3 In the Pick a task... list, click Reset my SpeedTouch to default settings. 4 The SpeedTouch™ restarts. 5 The SpeedTouch™ returns to the SpeedTouch™ Home page (unless the IP address of your computer is not in the same subnet as the default IP address of the SpeedTouch™, being 192.168.1.254). E-DOC-CTC-20050429-0104 v1.
© THOMSON 2005. All rights reserved. E-DOC-CTC-20050429-0104 v1.0 Need more help? Additional help is available online at www.speedtouch.
