User's Manual

ManualsBrandsTechnicolor - Thomson ManualsNetwork RouterTechnicolor - Thomson Network Router ST536

Power

DSL

Ethernet

Internet

Thomson ST516/536/546

CLI Reference Guide

Summary of content (792 pages)

PAGE 1
P o E w e r th D rn SL e t e In te rn e t Thomson ST516/536/546 CLI Reference Guide
PAGE 2
PAGE 3
Thomson ST516/536/546 CLI Reference Guide R6.
PAGE 4
Copyright Copyright ©1999-2007 THOMSON. All rights reserved. Distribution and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document.
PAGE 5
Contents About this CLI Reference Guide ................................................ 1 1 Root Commands .......................................................................... 3 ping.......................................................................................................................................................... 4 traceroute ................................................................................................................................................
PAGE 6
Contents atm debug aal5stats ............................................................................................................................. 41 atm debug gstats.................................................................................................................................. 42 atm debug portstats ............................................................................................................................. 43 atm oam config........................................
PAGE 7
Contents 6 Connection Commands............................................................. 81 connection appconfig........................................................................................................................... 82 connection appinfo............................................................................................................................... 84 connection applist ....................................................................................................
PAGE 8
Contents dhcp client debug traceconfig ........................................................................................................... 121 dhcp client rqoptions add .................................................................................................................. 122 dhcp client rqoptions delete .............................................................................................................. 123 dhcp client rqoptions list ............................................
PAGE 9
Contents dhcp server option instdelete ............................................................................................................ 163 dhcp server option instlist ................................................................................................................. 164 dhcp server option tmpladd .............................................................................................................. 165 dhcp server option tmpldelete .........................................
PAGE 10
Contents dns server route delete ...................................................................................................................... 205 dns server route flush ........................................................................................................................ 206 dns server route list............................................................................................................................ 207 11 DSD Commands........................................
PAGE 11
Contents env set ................................................................................................................................................. 247 env unset............................................................................................................................................. 248 14 Eth Commands ........................................................................ 249 eth ifadd ....................................................................................
PAGE 12
Contents eth bridge maclist ............................................................................................................................... 289 eth bridge mcdadd ............................................................................................................................. 290 eth bridge mcddelete ......................................................................................................................... 291 eth bridge mcdlist......................................
PAGE 13
Contents 15 Expr Commands ...................................................................... 327 expr add .............................................................................................................................................. 328 expr delete .......................................................................................................................................... 332 expr flush .......................................................................................
PAGE 14
Contents grp rip flush......................................................................................................................................... 382 grp rip ifconfig .................................................................................................................................... 383 grp rip show........................................................................................................................................ 385 18 Hostmgr Commands ..................
PAGE 15
Contents igmp proxy iflist.................................................................................................................................. 422 igmp proxy mbslist ............................................................................................................................ 423 igmp proxy debug clear ..................................................................................................................... 424 igmp proxy debug stats ..................................
PAGE 16
Contents ip auto ifdetach ................................................................................................................................... 465 ip auto iflist ......................................................................................................................................... 466 ip debug httpprobe............................................................................................................................. 467 ip debug sendto ............................
PAGE 17
Contents language config .................................................................................................................................. 514 language delete .................................................................................................................................. 515 language list........................................................................................................................................ 516 26 MBUS Commands ...........................
PAGE 18
Contents mlp privilege config ........................................................................................................................... 552 mlp privilege delete............................................................................................................................ 553 mlp privilege list ................................................................................................................................. 555 mlp privilege removezone ..........................
PAGE 19
Contents ppp relay ifdelete................................................................................................................................ 607 ppp relay iflist ..................................................................................................................................... 608 ppp relay sesslist ................................................................................................................................ 609 31 PPTP Commands .........................
PAGE 20
Contents service system modify ....................................................................................................................... 647 34 SNMP Commands ................................................................... 649 snmp config ........................................................................................................................................ 650 snmp get .......................................................................................................
PAGE 21
Contents system ra config ................................................................................................................................. 687 system rtc synchronize ...................................................................................................................... 688 system rtc settime .............................................................................................................................. 689 38 Systemlog Commands................................
PAGE 22
Contents user flush............................................................................................................................................. 727 user list ................................................................................................................................................ 728 user rights ........................................................................................................................................... 730 42 Abbreviations.............
PAGE 23
About this CLI Reference Guide About this CLI Reference Guide Used Symbols i A note provides additional information about a topic. ! A caution warns you about potential problems or specific precautions that need to be taken. Terminology Generally, the Thomson ST516/536/546 will be referred to as Thomson ST in this CLI Reference Guide. Typographical Conventions Following typographical convention is used throughout this manual: > Sample text indicates a hyperlink to a Web site.
PAGE 24
About this CLI Reference Guide 2 E-DOC-CTC-20061027-0003 v2.
PAGE 25
Root Commands 1 Root Commands From the root prompt, you can choose one of the following commands: Command Description help Displays the help information. ? menu Displays the menu. exit Exits the shell. .. Exits group selection. saveall Saves current configuration. ping Send ICMP ECHO_REQUEST packets. traceroute Send ICMP/UDP packets to trace the ip path.
PAGE 26
Root Commands ping Send ICMP ECHO_REQUEST packets. SYNTAX: ping proto = <{ip|atm}> addr = dest = [count = ] [size = ] [interval(ms) = ] [DF-bit = <{disabled|enabled}>] [srcaddr = ] where: proto The interface type to be used. Choose between: > > REQUIRED ip atm addr The destination IP address. REQUIRED dest The destination address for the request. REQUIRED count A number between 1 and 1000000.
PAGE 27
Root Commands traceroute Send ICMP/UDP packets to trace the IP path. SYNTAX: traceroute addr = [count = ] [size = ] [interval = ] [maxhops = ] [dstport = ] [maxfail = ] [type = <{icmp | udp}>] [utime = <{disabled | enabled}>] where: addr The destination IP address. REQUIRED count A number between 1 and 10. Represents the number of times to reissue a traceroute request with the same TTL.
PAGE 28
Root Commands EXAMPLE: =>traceroute addr = 192.193.195.250 count=3 size=1 interval=1000 maxhops=30 dstport=33433 maxfail=5 type=icmp utime=yes :traceroute addr=192.193.195.250 ttl=1 192.193.195.250 676 us 1351 us 648 us => 6 E-DOC-CTC-20061027-0003 v2.
PAGE 29
ADSL Commands 2 ADSL Commands Introduction This chapter describes the commands of the adsl command group. Contents This chapter covers the following commands: adsl config Show/set the Asymmetric Digital Subscriber Line (ADSL) configuration. 8 adsl info Display the ADSL statistics and information about the DSL line status. 9 adsl debug bitloadinginfo Displays the number of bits per tone.
PAGE 30
ADSL Commands adsl config Show/set the Asymmetric Digital Subscriber Line (ADSL) configuration. SYNTAX: adsl config [opermode = <{multimode | multi_adsl2 | multi_readsl2 | multi_adsl2plus}>] [trace = <{disabled | enabled}>] where: opermode The operational mode of the Thomson ST. Choose between: > > > > OPTIONAL multimode multi_adsl2 multi_readsl2 multi_adsl2plus The default is multi_adsl2plus. trace Enable or disable ADSL tracing. The default is enabled.
PAGE 31
ADSL Commands adsl info Display the ADSL statistics and information about the DSL line status. Although the same command is used for both Thomson ST ADSL/POTS and Thomson ST ADSL/ISDN variants, the command features specific output parameters and counters per variant. SYNTAX: adsl info E-DOC-CTC-20061027-0003 v2.
PAGE 32
ADSL Commands EXAMPLE (for a Thomson ST ADSL/POTS variant): =>adsl info Modemstate Operation Mode Channel Mode Number of resets : : : : Vendor Country Vendor VendorSpecific StandardRevisionNr : : : : Local 0f TMMB 0000 00 Margin Attenuation OutputPower : : : Downstream 26.0 0.0 4.
PAGE 33
ADSL Commands adsl debug bitloadinginfo Displays the number of bits per tone. Syntax adsl debug bitloadinginfo E-DOC-CTC-20061027-0003 v2.
PAGE 34
ADSL Commands adsl debug deltconfig Enable/disable the Dual Ended Line Testing Interface (DELT) Syntax adsl debug deltconfig [state = <{disabled|enabled}>] where: state 12 enable or disable DELT REQUIRED E-DOC-CTC-20061027-0003 v2.
PAGE 35
ADSL Commands adsl debug deltinfo Display Dual Ended Line Testing Interface (DELT) results Syntax adsl debug deltinfo E-DOC-CTC-20061027-0003 v2.
PAGE 36
ADSL Commands adsl debug modemoptioninfo Displays the modem options bitmap Syntax adsl debug modemoptioninfo 14 E-DOC-CTC-20061027-0003 v2.
PAGE 37
ADSL Commands adsl debug modemoption Configure the modem options bitmap Syntax adsl debug modemoption [config = ] where: config E-DOC-CTC-20061027-0003 v2.
PAGE 38
ADSL Commands adsl debug traceconfig Configure the ADSL tracelevel. Syntax adsl debug traceconfig [level = ] where: level Trace Level: > > > 16 REQUIRED 0=disable tracing; 1=enable dsl manager tracing; 2=enable dsl driver tracing) E-DOC-CTC-20061027-0003 v2.
PAGE 39
ATM Commands 3 ATM Commands Introduction This chapter describes the commands of the atm command group. Contents This chapter covers the following commands: atm flush Flush all Asynchronous Transfer Mode (ATM) interfaces. 19 atm ifadd Create a new ATM interface. 20 atm ifattach Attach a ATM interface. 21 atm ifconfig Configure an ATM interface. 22 atm ifdelete Delete an ATM interface. 24 atm ifdetach Detach an ATM interface. 25 atm iflist Display the ATM interfaces.
PAGE 40
ATM Commands 18 atm oam vclb add Create a loopback connection for VC. 52 atm oam vclb del Delete a loopback connection for VC. 53 atm oam vclb list List all VC loopback connections. 54 atm phonebook add Add a new phonebook entry. 55 atm phonebook autolist Show the auto PVCs. 56 atm phonebook delete Delete an existing phonebook entry. 57 atm phonebook flush Flush all the phonebook entries. 58 atm phonebook list Display the current phonebook.
PAGE 41
ATM Commands atm flush Flush all Asynchronous Transfer Mode (ATM) interfaces. SYNTAX: atm flush E-DOC-CTC-20061027-0003 v2.
PAGE 42
ATM Commands atm ifadd Create a new ATM interface. SYNTAX: atm ifadd intf = where: intf The name for the new ATM interface. Note REQUIRED If not specified, the destination parameter must be specified. In this case the name of the destination will double as interface name.
PAGE 43
ATM Commands atm ifattach Attach a ATM interface. SYNTAX: atm ifattach intf = where: intf The name of the ATM interface to be attached.
PAGE 44
ATM Commands atm ifconfig Configure an ATM interface. i The interface to be configured must not be connected at the time of configuration. If this should be the case, use the command :atm ifdetach before using the command :atm ifconfig.
PAGE 45
ATM Commands ulp Select the Upper Layer Protocol (ULP) for this interface. Choose between: > > > OPTIONAL ip (for a Routed IPoA interface). mac (for a Bridged Ethernet, Routed ETHoA, Bridged PPP over Ethernet (PPPoE), Routed PPPoE or a PPPoE Relay interface). ppp (for a Routed PPP over ATM (PPPoA) interface). The default is ip.
PAGE 46
ATM Commands atm ifdelete Delete an ATM interface. SYNTAX: atm ifdelete intf = where: intf The name of the ATM interface to be deleted.
PAGE 47
ATM Commands atm ifdetach Detach an ATM interface. SYNTAX: atm ifdetach intf = where: intf The name of the ATM interface to be detached.
PAGE 48
ATM Commands atm iflist Display the ATM interfaces. SYNTAX: atm iflist [intf = ] where: intf The name of the ATM interface to be shown. Note OPTIONAL If not specified, all the ATM interfaces are shown.
PAGE 49
ATM Commands atm bundle add Add a new bundle of interfaces. SYNTAX: atm bundle add name = where: name The name of the new bundle. REQUIRED EXAMPLE: =>atm bundle add name=myBundle =>atm bundle list myBundle: Connection state : not-connected Retry: 10 Policy: priority Propagate: disabled TX requested bytes: 0 requested frames: 0 TX bytes: 0 frames: 0 RX bytes: 0 frames: 0 => RELATED COMMANDS: atm bundle delete Delete a bundle of interfaces. atm bundle list Display the current bundles.
PAGE 50
ATM Commands atm bundle attach Attach a bundle of interfaces. SYNTAX: atm bundle attach name = where: name The name of the bundle to be attached. REQUIRED EXAMPLE: =>atm bundle attach name=myBundle =>atm bundle list myBundle: Connection state : connected Retry: 10 TX requested bytes: 0 TX bytes: 0 RX bytes: 0 => Policy: priority Propagate: disabled requested frames: 0 frames: 0 frames: 0 RELATED COMMANDS: atm bundle detach 28 Detach a bundle of interfaces. E-DOC-CTC-20061027-0003 v2.
PAGE 51
ATM Commands atm bundle config Modify a bundle of interfaces. i The bundle of interfaces to be configured must not be connected at the time of configuration. If this should be the case, use the command :atm bundle detach before using the command :atm bundle config. SYNTAX: atm bundle config name = [policy = <{priority | connection}>] [propagate = <{disabled | enabled}>] [retry = ] where: name The name of the bundle to be configured.
PAGE 52
ATM Commands atm bundle clear Clear the bundle statistics. SYNTAX: atm bundle clear [name = ] where: name The name of the bundle for which the statistics must be cleared. Note 30 OPTIONAL If not specified, the statistics for all the bundles will be cleared. E-DOC-CTC-20061027-0003 v2.
PAGE 53
ATM Commands atm bundle delete Delete a bundle of interfaces. SYNTAX: atm bundle delete name = where: name The name of the bundle to be deleted. REQUIRED RELATED COMMANDS: atm bundle add Add a new bundle of interfaces. atm bundle list Display the current bundles. E-DOC-CTC-20061027-0003 v2.
PAGE 54
ATM Commands atm bundle detach Detach a bundle of interfaces. SYNTAX: atm bundle detach intf = where: intf The name of the bundle to be detached. REQUIRED RELATED COMMANDS: atm bundle attach 32 Attach a bundle of interfaces. E-DOC-CTC-20061027-0003 v2.
PAGE 55
ATM Commands atm bundle flush Flush all bundles. SYNTAX: atm bundle flush E-DOC-CTC-20061027-0003 v2.
PAGE 56
ATM Commands atm bundle ifadd Add an interface on a bundle. i Up to 8 interfaces or (sub-)bundles can be added to one bundle. SYNTAX: atm bundle ifadd name = intf = [index = ] where: name The name of the bundle to which an ATM interface must be added. REQUIRED intf The name of the ATM interface to be added. REQUIRED index A number between 0 and 6. Represents the index of the ATM interface.
PAGE 57
ATM Commands atm bundle ifconfig Configure an interface from a bundle. i The interface to be configured must not be connected at the time of configuration. If this should be the case, use the command :atm bundle ifdetach before using the command :atm bundle ifconfig. SYNTAX: atm bundle ifconfig name = intf = [state = <{disabled | enabled}>] [low = ] [high = ] where: name The name of the bundle from which an ATM interface must be configured.
PAGE 58
ATM Commands atm bundle ifdelete Remove an interface from a bundle. SYNTAX: atm bundle ifdelete name = intf = where: name The name of the bundle from which an ATM interface must be removed. REQUIRED intf The name of the ATM interface to be removed.
PAGE 59
ATM Commands atm bundle list Display the current bundles. SYNTAX: atm bundle list EXAMPLE: =>atm bundle list Test : Connection state : not-connected Retry: 10 Policy: priority TX requested bytes: 0 requested frames: 0 TX bytes: 0 frames: 0 RX bytes: 0 frames: 0 Interface: Test State: enabled Selector: 0-15 TX bytes: 0 frames: 0 RX bytes: 0 frames: 0 RX discarded bytes: 0 discarded frames: 0 Disconnects: 0 => RELATED COMMANDS: atm bundle add Add a new bundle of interfaces.
PAGE 60
ATM Commands atm cac config Configure the ATM connection admission control. SYNTAX: atm cac config config port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number> state = <{disabled|enabled}> where: config port The port for which CAC is configured. REQUIRED state Enable/disable CAC for an ATM port. REQUIRED EXAMPLE: {Administrator}=>atm cac config port = dsl0 state = enabled :atm cac config port=dsl0 state=enabled {Administrator}=> RELATED COMMANDS: 38 atm cac list Display all the CAC parameters.
PAGE 61
ATM Commands atm cac list Display all the CAC parameters. SYNTAX: atm cac list EXAMPLE: {Administrator}[atm cac]=>list CAC: port: dsl0 state: enabled CAC: port: dsl1 state: enabled CAC: port: atm2 state: enabled CAC: port: aal5 state: disabled CAC: port: atm5 state: disabled Overbooking: realtime: 0% non-realtime: 0%. {Administrator}[atm cac]=> RELATED COMMANDS: atm cac config Configure the ATM connection admission control. atm cac overbooking Configure ATM overbooking parameters.
PAGE 62
ATM Commands atm cac overbooking Configure ATM overbooking parameters. SYNTAX: atm cac overbooking rt = nrt = where: rt A number between 0 and 1000. The realtime overbooking percentage. REQUIRED nrt A number between 0 and 1000. The non-realtime overbooking percentage.
PAGE 63
ATM Commands atm debug aal5stats Display ATM Adaptation Layer 5 (AAL5) port specific ATM statistics. SYNTAX: atm debug aal5stats port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number> vpi = [vci = ] [clear = <{disabled | enabled}>] where: port The port number for which statistics will be retrieved. Choose between: > > > > > > REQUIRED DSL0 DSL1 ATM2 ATM3 AAL5 ATM5 Or specify a port number (dsl0 has port number 0). vpi A number between 0 and 15.
PAGE 64
ATM Commands atm debug gstats Display ATM global statistics. SYNTAX: atm debug gstats [clear = <{disabled | enabled}>] where: clear Enable or disable clearing of the statistics after request. OPTIONAL EXAMPLE: {admin}[atm debug]=>gstats # of received octets = 1802. # of transmitted octets = 4346. # of received cells = 34. # of transmitted cells = 82. # of unknown cells = 0. # of errors on the input = 0. # of errors on output = 0.
PAGE 65
ATM Commands atm debug portstats Display port specific ATM statistics. SYNTAX: atm debug portstats port = <{dsl0} or number> [clear = <{disabled | enabled}>] where: port The port number for which statistics will be retrieved. Choose between: > REQUIRED DSL0 Or specify a port number (dsl0 has port number 0). clear Enable or disable clearing of the statistics after request. OPTIONAL EXAMPLE: =>atm debug portstats port=dsl0 # of received octets = 1961. # of transmitted octets = 4717.
PAGE 66
ATM Commands atm oam config Modify the ATM Operation and Maintenance (OAM) settings. SYNTAX: atm oam config [clp = ] [loopbackid = ] where: clp A number (0 or 1). Represents the Cell Loss Priority (CLP) bit value of the OAM cells. The default is 1. OPTIONAL loopbackid A hexadecimal string. Represents the loopback ID for processing of segment loopback cells. The default is 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a.
PAGE 67
ATM Commands atm oam list Display the ATM OAM settings. SYNTAX: atm oam list EXAMPLE: =>atm oam list OAM config dump ------------------CLP bit value : 1 Loopback id : 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a OAM data blocking mode -------------------------Port dsl0: blocking Port dsl1: blocking Port atm2: blocking Port atm3: blocking Port aal5: blocking Port atm5: blocking => RELATED COMMANDS: atm oam config Modify the ATM Operation and Maintenance (OAM) settings.
PAGE 68
ATM Commands atm oam modify Modify the ATM OAM data blocking mode. SYNTAX: atm oam modify port = <{dsl0} or number> blocking = <{disabled | enabled}> where: port The port for which OAM blocking is configured. Choose between: > REQUIRED DSL0 Or specify a port number (dsl0 has port number 0). blocking 46 Enable or disable the OAM data blocking mode on this port. The default is enabled. REQUIRED E-DOC-CTC-20061027-0003 v2.
PAGE 69
ATM Commands EXAMPLE: =>atm oam list OAM config dump ------------------CLP bit value : 1 Loopback id : 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a OAM data blocking mode -------------------------Port dsl0: blocking Port dsl1: blocking Port atm2: blocking Port atm3: blocking Port aal5: blocking Port atm5: blocking =>atm oam modify port=dsl1 blocking=disabled =>:atm oam list OAM config dump ------------------CLP bit value : 1 Loopback id : 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a OAM data blocking
PAGE 70
ATM Commands atm oam ping Send ATM loopback cells. SYNTAX: atm oam ping dest = [count = ] [interval = ] where: dest The destination address for the request. This can be any ATM phonebook entry. REQUIRED count A number between 1 and 1000000. Represents the number of pings to send. OPTIONAL interval A number between 100 and 1000000 (milliseconds). Represents the interval between packets.
PAGE 71
ATM Commands atm oam cc list Display Continuity Check (CC) configuration. SYNTAX: atm oam cc list EXAMPLE: =>atm oam cclist PORT = 0 VPI = 15 VCI = 16 End2End Mode = Auto Segment Mode = Auto PORT = 0 VPI = 0 VCI = 35 End2End Mode = Auto Segment Mode = Auto PORT = 0 VPI = 8 VCI = 35 End2End Mode = Auto Segment Mode = Auto PORT = 0 VPI = 0 VCI = 16 End2End Mode = Auto Segment Mode = Auto => RELATED COMMANDS: atm oam cc modify Modify CC on the connection.
PAGE 72
ATM Commands atm oam cc modify Modify CC on the connection. SYNTAX: atm oam modify port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number> vpi = [vci = ] [transmit = <{disabled | enabled}>] [receive = <{disabled | enabled}>] [auto = <{disabled | enabled}>] [span = <{segment | end2end}>] where: port The ATM port number. Choose between: > > > > > > REQUIRED DSL0 DSL1 ATM2 ATM3 AAL5 ATM5 Or specify a port number (dsl0 has port number 0). vpi A number between 0 and 15.
PAGE 73
ATM Commands atm oam cc send Send CC activate/deactivate to connection. SYNTAX: atm oam cc send port = <{dsl0} or number> vpi = [vci = ] [span = <{segment | end2end}>] [action = <{activate | deactivate}>] [direction = <{source | sink | both}>] where: port The ATM port number. Choose between: > REQUIRED DSL0. Or specify a port number (dsl0 has port number 0). vpi A number between 0 and 15. Represents the VPI. REQUIRED vci A number between 0 and 511.
PAGE 74
ATM Commands atm oam vclb add Create a loopback connection for VC. SYNTAX: atm oam vclb add port = <{dsl0} or number> vpi = [vci = ] where: port The ATM port number. Choose between: > REQUIRED DSL0 Or specify a port number (dsl0 has port number 0). vpi A number between 0 and 15. Represents the VPI. REQUIRED vci A number between 0 and 511. Represents the VCI. OPTIONAL Note For a VP cross-connection, use 0 or do not specify.
PAGE 75
ATM Commands atm oam vclb del Delete a loopback connection for VC. SYNTAX: atm oam vclb del port = <{dsl0} or number> vpi = [vci = ] where: port The ATM port number. Choose between: > REQUIRED DSL0 Or specify a port number (dsl0 has port number 0). vpi A number between 0 and 15. Represents the VPI. REQUIRED vci A number between 0 and 511. Represents the VCI. OPTIONAL Note For a VP cross-connection, use 0 or do not specify.
PAGE 76
ATM Commands atm oam vclb list List all VC loopback connections. SYNTAX: atm oam vclb list EXAMPLE: =>atm oam vclb list PORT = 0 VPI = 0 VCI = PORT = 1 VPI = 0 VCI = => 36 37 RELATED COMMANDS: 54 atm oam vclb add Create a loopback connection for VC. atm oam vclb del Delete a loopback connection for VC. E-DOC-CTC-20061027-0003 v2.
PAGE 77
ATM Commands atm phonebook add Add a new phonebook entry. SYNTAX: atm phonebook add name = addr = where: name addr The name of the new phonebook entry.
PAGE 78
ATM Commands atm phonebook autolist Show the auto PVCs. i Auto PVCs are only shown if they are supported by the Central Office DSLAM. SYNTAX: atm phonebook autolist EXAMPLE: =>atm phonebook autolist 8.35 => RELATED COMMANDS: atm phonebook list 56 Display the current phonebook. E-DOC-CTC-20061027-0003 v2.
PAGE 79
ATM Commands atm phonebook delete Delete an existing phonebook entry. i This command is only applicable for phonebook entries that are not used (in other words, not configured for any packet service). SYNTAX: atm phonebook delete name = where: name The name of the phonebook entry to be deleted. Tip REQUIRED Use the command :atm phonebook list to check whether the entry is in use (Use=1) or not (Use=0). EXAMPLE: =>atm phonebook list Name Use Address atm_pvc_0_35 1 0.35 RtPPPoA 0 8.
PAGE 80
ATM Commands atm phonebook flush Flush all the phonebook entries. i 1. Phonebook entries that are in use, cannot be flushed. 2. This command does not impact previously saved configurations. SYNTAX: atm phonebook flush EXAMPLE: =>atm phonebook list Name Use Address atm_pvc_0_35 1 0.35 RtPPPoA 0 8.35 => =>atm phonebook flush Some phonebook entries are still in use. Entries that are in use cannot be deleted. => =>atm phonebook list Name Use Address atm_pvc_0_35 1 0.35 => 58 E-DOC-CTC-20061027-0003 v2.
PAGE 81
ATM Commands atm phonebook list Display the current phonebook. SYNTAX: atm phonebook list EXAMPLE: =>atm phonebook list Name Use Address atm_pvc_0_35 1 0.35 RtPPPoA 0 8.35 => RELATED COMMANDS: atm phonebook add Add a new phonebook entry. atm phonebook autolist Show the auto PVCs. atm phonebook delete Delete an existing phonebook entry. E-DOC-CTC-20061027-0003 v2.
PAGE 82
ATM Commands atm qosbook add Add a new QoS book entry. SYNTAX: atm qosbook add name = [txctd = ] [rxctd = ] where: name The name of the new QoS entry. REQUIRED txctd The name of the Conformance Traffic Descriptor (CTD) for the transmit (upstream) direction. OPTIONAL rxctd The name of the CTD for the receive (downstream) direction.
PAGE 83
ATM Commands atm qosbook config Modify the QoS book configuration. SYNTAX: atm qosbook config [format = <{bytes | cells}>] where: format The input/output format of the QoS book. Choose between: > > OPTIONAL bytes: the output is shown in Kbits or bytes. cells: the output is shown in cps or cells. The default is bytes.
PAGE 84
ATM Commands atm qosbook ctdadd Add a Connection Traffic Descriptor (CTD). SYNTAX: atm qosbook ctdadd name = conformance = <{UBR | CBR | VBR }> [peakrate = ] [sustrate = ] [realtime = <{enabled | disabled}>] where: name The name of the new CTD. REQUIRED conformance The ATM service conformance definition. REQUIRED peakrate A number between 0 and 27786. Represents the peak rate (in kilobits per second).
PAGE 85
ATM Commands IMPORTANT NOTE: The Thomson ST always rounds up specified burst sizes to a multiple of 48 bytes (a multiple of ATM cells). Example: In the example below a burst size of 100 bytes is specified (maxburst=100). The Thomson ST will round up the burst size to the closest matching multiple of 48 bytes, as can be seen when displaying the profile via the command :atm qosbook ctdlist (burst=144).
PAGE 86
ATM Commands atm qosbook ctddelete Delete a CTD. SYNTAX: atm qosbook ctddelete name = [force = <{disabled | enabled}>] where: name The name of the CTD entry to be deleted. REQUIRED force Enable or disable to force delete the entry even when it is still in use. The default is disabled.
PAGE 87
ATM Commands atm qosbook ctdlist Display all CTDs. SYNTAX: atm qosbook ctdlist EXAMPLE: =>atm qosbook ctdlist Name Ref Conf Peak (Kbits) default 2 led High 0 led => Sust (Kbits) Burst (bytes) Minrate (Kbits) Frame (bytes) Cdvt RT FD UBR linerate 0 0 0 0 0 disabled disab CBR 27786 0 0 0 0 disabled disab 0 RELATED COMMANDS: atm qosbook ctdadd Add a Connection Traffic Descriptor (CTD). atm qosbook ctddelete Delete a CTD. E-DOC-CTC-20061027-0003 v2.
PAGE 88
ATM Commands atm qosbook delete Delete a QoS book entry. SYNTAX: atm qosbook delete name = [force = <{disabled | enabled}>] where: name The name of the QoS book entry to be deleted. REQUIRED force Enable or disable to force delete the entry even when it is still in use. The default is disabled.
PAGE 89
ATM Commands atm qosbook flush Flush all the QoS book entries. i The flush command does not impact previously saved configurations. SYNTAX: atm qosbook flush E-DOC-CTC-20061027-0003 v2.
PAGE 90
ATM Commands atm qosbook list Display the QoS book. SYNTAX: atm qosbook list EXAMPLE: =>atm qosbook list Name Ref Type default 3 TestVBR 0 => TX peak (Kbits) ubr linerate vbr-nrt 1500 sust (Kbits) 0 1000 burst (bytes) 0 144 RX peak (Kbits) linerate 1500 sust (Kbits) 0 1000 burst (bytes) 0 144 framediscard disabled enabled RELATED COMMANDS: 68 atm qosbook add Add a new QoS book entry. atm qosbook delete Delete a QoS book entry. E-DOC-CTC-20061027-0003 v2.
PAGE 91
AutoPVC Commands 4 AutoPVC Commands Introduction This chapter describes the commands of the autopvc command group. Contents This chapter covers the following commands: autopvc config Configure autopvc. 70 autopvc list Show the retrieved information. 72 E-DOC-CTC-20061027-0003 v2.
PAGE 92
AutoPVC Commands autopvc config Configure autopvc. SYNTAX: autopvc config [mode = <{pseudo | passive | active}>] [type = <{bridge | pppoerelay | ipoa | ethoa | pppoa | pppoe }>] [overwrite = <{disabled | enabled}>] [peakrate = ] where: mode Select the autopvc mode: OPTIONAL > pseudo: only pseudo-ILMI (VP/VC 15/16) is enabled.
PAGE 93
AutoPVC Commands EXAMPLE: =>autopvc config Autopvc mode : Autopvc type : Autopvc standard: Autopvc pseudo : UBR overwrite : UBR peak rate : => E-DOC-CTC-20061027-0003 v2.
PAGE 94
AutoPVC Commands autopvc list Show the retrieved information. SYNTAX: autopvc list [table = <{Port | AtmLayer | Vpc | Vcc | Address | AddressRegistrationAdmin | AtmServiceType | AtmServiceConnectionInfo | AAL1Profile | | AAL34Profile | AAL5Profile | AAL2CommonProfile | AAL2TrunkingProfile | AAL2LESProfile | AtmServiceConnInfoExtension | | AtmServiceTypeExtension | AAL5ProfileExtension}>] where: table Select the autopvc table for which the information must be shown.
PAGE 95
Config Commands 5 Config Commands Introduction This chapter describes the commands of the config command group. Contents This chapter covers the following commands: config delete Delete a user configuration file. 74 config dump Show the saved configuration file. 75 config flush Flush the loaded configuration. 76 config list Show the current configuration set. 77 config load Load complete saved (backup) or default configuration file.
PAGE 96
Config Commands config delete Delete a user configuration file. SYNTAX: config delete [filename = ] where: filename Name of the user configuration file to be deleted. Note OPTIONAL If not specified, all the user configuration files that were saved in the Thomson ST permanent storage will be deleted. RELATED COMMANDS: config dump 74 Show the saved configuration file. E-DOC-CTC-20061027-0003 v2.
PAGE 97
Config Commands config dump Show the saved configuration file. SYNTAX: config dump [sections = ] where: sections Sections to be dumped OPTIONAL RELATED COMMANDS: config delete E-DOC-CTC-20061027-0003 v2.0 Delete a user configuration file.
PAGE 98
Config Commands config flush Flush the loaded configuration. i 1. This flush command combines all the possible flush commands. 2. This command does not affect saved configurations. SYNTAX: config flush [flush_ip = <{enabled | disabled}>] where: flush_ip Flush IP settings (enabled) or not (disabled). The default is enabled. Note 76 OPTIONAL Not keeping the IP settings could cause lost IP connectivity in the LAN. E-DOC-CTC-20061027-0003 v2.
PAGE 99
Config Commands config list Show the current configuration set. SYNTAX: config list [templates = <{disabled | enabled}>] where: templates List the template files (disabled) or not (enabled). The default is disabled. OPTIONAL RELATED COMMANDS: config load Load complete saved (backup) or default configuration file. config save Store the current configuration in a backup file. E-DOC-CTC-20061027-0003 v2.
PAGE 100
Config Commands config load Load complete saved (backup) or default configuration file. i Use the command :config flush before loading a configuration file. SYNTAX: config load [load_ip = <{enabled | disabled}>] [defaults = <{enabled | disabled}>] [flush = <{enabled | disabled}>] [echo = <{disabled | enabled}>] [filename = ] where: load_ip Load IP settings (enabled) or not (disabled). Note defaults Not keeping the IP settings could cause lost IP connectivity in the LAN.
PAGE 101
Config Commands EXAMPLE: =>ip rtlist Destination Source 10.0.0.0/24 10.0.0.0/24 172.16.0.5/32 0.0.0.0/0 10.0.0.140/32 0.0.0.0/0 127.0.0.1/32 0.0.0.0/0 172.16.0.0/24 0.0.0.0/0 =>config load flush_ip=no =>ip rtlist Destination Source 10.0.0.0/24 10.0.0.0/24 10.0.0.140/32 0.0.0.0/0 127.0.0.1/32 0.0.0.0/0 =>config load flush=yes =>ip rtlist Destination Source 10.0.0.0/24 10.0.0.0/24 10.0.0.140/32 0.0.0.0/0 172.16.0.5/32 0.0.0.0/0 127.0.0.1/32 0.0.0.0/0 172.16.0.0/24 0.0.0.0/0 => Gateway 10.0.0.140 172.16.0.
PAGE 102
Config Commands config save Store the current configuration in a backup file. All the existing configurations and modifications entered by the user are saved. The backup file is saved in the Thomson ST permanent storage. This file can be downloaded via the Thomson ST web pages or via an FTP session. SYNTAX: config save filename = where: filename The filename for the backup file of the current configuration. REQUIRED RELATED COMMANDS: 80 config list Show the current configuration set.
PAGE 103
Connection Commands 6 Connection Commands Introduction This chapter describes the commands of the connection command group. Contents This chapter covers the following commands: connection appconfig Configure the available CONN/NAT application helpers. 82 connection appinfo Display CONN/NAT application specific info. 84 connection applist List the available CONN/NAT application helpers. 85 connection bind Create a new CONN/NAT application helper/port binding.
PAGE 104
Connection Commands connection appconfig Configure the available CONN/NAT application helpers. SYNTAX: connection appconfig application = [trace = <{disabled | enabled}>] [timeout = ] [floating = <{disabled | enabled}>] [childqos = <{DSCP|Interactive| Management|Video|VoIP|default}>] [tracelevel = ] [SIP_ALG = <{disabled|enabled}>] [RTP_predict_for_term_SIP_ALG = <{disabled|enabled}>] where: application The name of a CONN/NAT application helper.
PAGE 105
Connection Commands EXAMPLE: =>connection Application IP6TO4 PPTP ESP IKE SIP ... LOOSE(UDP) FTP =>connection =>connection Application IP6TO4 PPTP ESP IKE SIP ...
PAGE 106
Connection Commands connection appinfo Display CONN/NAT application specific info. SYNTAX: connection appinfo application = <{string}> where: application The name of a CONN/NAT application helper. Tip REQUIRED Use the command :connection applist to obtain a list of CONN/NAT application helpers. EXAMPLE: =>connection appinfo application=SIP SIP ALG session SIPALG: pool=138, in use=0, bottom=138 => RELATED COMMANDS: 84 connection appconfig Configure the available CONN/NAT application helpers.
PAGE 107
Connection Commands connection applist List the available CONN/NAT application helpers.
PAGE 108
Connection Commands connection bind Create a new CONN/NAT application helper/port binding. SYNTAX: connection bind application = port = where: application The name of a CONN/NAT application helper. Tip port REQUIRED Use the command :connection applist to obtain a list of CONN/NAT application helpers. The port number or port range this application handler should work on. REQUIRED EXAMPLE: =>connection Application JABBER JABBER FTP IRC ...
PAGE 109
Connection Commands connection bindlist List the current CONN/NAT application helper/port bindings.
PAGE 110
Connection Commands connection clean Clean the connection database by forcing timeouts. SYNTAX: connection clean [level = ] where: level A number between 0 and 9. Represents the desired scrubbing level. OPTIONAL EXAMPLE: =>connection list ID proto state ------ ----8 tcp ACTIVE INIT: 16 192.168. RESP: 17 192.168. 34 tcp ACTIVE INIT: 68 192.168. RESP: 69 192.168. =>connection clean =>connection list ID proto state ------ ----8 tcp ACTIVE INIT: 16 192.168. RESP: 17 192.168.
PAGE 111
Connection Commands connection clear Kill all the connections. SYNTAX: connection clear EXAMPLE: =>connection clear Connection to host lost. E-DOC-CTC-20061027-0003 v2.
PAGE 112
Connection Commands connection config Configure the connection handling. SYNTAX: connection config [configchangemode = <{immediate | delayed}>] [probes = <{disabled | enabled}>] [udptrackmode = <{strict | loose}>] where: configchangemode Select how configuration changes are handled. Choose between: > > OPTIONAL immediate delayed. The default is immediate. probes Enable or disable live probes on idle connections. The default is disabled.
PAGE 113
Connection Commands connection debug The connection debug commands SYNTAX: connection debug [trace = <{disabled|enabled}>] where: trace Enable or disable traces. The default is disabled. OPTIONAL EXAMPLE: =>connection debug connection traces : disabled => =>connection debug trace enabled => =>connection debug connection traces : enabled => E-DOC-CTC-20061027-0003 v2.
PAGE 114
Connection Commands connection describe Describe the streams of a connection. SYNTAX: connection describe [id = ] where: id A number between 0 and 2048. Represents the ID of the connection to be described. Note Tip OPTIONAL If not specified, the connection with ID 0 will be described. Use the command :connection list to obtain the IDs of the different connections.
PAGE 115
Connection Commands connection flush Flush the current connection configuration. SYNTAX: connection flush E-DOC-CTC-20061027-0003 v2.
PAGE 116
Connection Commands connection info Show all the registered modules with some info. SYNTAX: connection info EXAMPLE: =>connection info Registered connection modules : - Module : FW, holds private data (F:10264 S:6592). - Module : IDS, holds private data (F:0 S:0). - Module : NAT, holds private data (F:0 S:0). Registered stream modules : - Module : ROUTING, holds private data (F:10199 S:6657). - Module : LABEL, holds private data (F:22546 S:19870). - Module : IPQOS, holds private data (F:10202 S:6653).
PAGE 117
Connection Commands connection list Display the currently known connections. SYNTAX: connection list [nr = ][string = ] [beginstring = ] where: nr A number between 1 and 2048. Represents the number of connections to be displayed. Note OPTIONAL If not specified, all the connections will be displayed.
PAGE 118
Connection Commands connection refresh Invalidate all the cached decisions. SYNTAX: connection refresh 96 E-DOC-CTC-20061027-0003 v2.
PAGE 119
Connection Commands connection stats Display the connection and stream statistics.
PAGE 120
Connection Commands connection timerclear Clear the connection timeout to default. SYNTAX: connection timerclear [timer = <{tcpidle|tcpneg|tcpkill|udpidle|udpkill| icmpkill|ipidle|ipkill}>] where: timer The name of the connection idle timer to be reset. Note REQUIRED If not specified, all the timers will be reset to their default values.
PAGE 121
Connection Commands connection timerconfig Configure the connection timeout handling. SYNTAX: connection timerconfig [timer = <{tcpidle|tcpneg|tcpkill|udpidle|udpkill| icmpkill|ipidle|ipkill}>] [value = ] where: timer The name of the connection idle timer to be configured. Choose between: > > > > > > > > value OPTIONAL tcpidle tcpneg tcpkill udpidle udpkill icmpkill ipidle ipkill A number between 0 and 86400 (seconds). Represents the timer expire value.
PAGE 122
Connection Commands connection unbind Delete an existing CONN/NAT application helper/port binding. SYNTAX: connection unbind application = port = where: application The name of a CONN/NAT application helper. Tip port REQUIRED Use the command :connection applist to obtain a list of CONN/NAT application helpers. The port number or port range this application handler should work on. REQUIRED EXAMPLE: =>connection Application IRC JABBER JABBER FTP IRC ...
PAGE 123
CWMP Commands 7 CWMP Commands Introduction This chapter describes the commands of the cwmp (CPE WAN Management Protocol) command group. Contents This chapter covers the following commands: cwmp config Configure the cwmpd as seen from the ACS. 102 cwmp server config Configure the cwmpd towards the ACS. 104 E-DOC-CTC-20061027-0003 v2.
PAGE 124
CWMP Commands cwmp config Configure the cwmpd as seen from the ACS.
PAGE 125
CWMP Commands connectionRequest Set the connection request flag of the cwmp daemon. Choose between: > > OPTIONAL enabled disabled. The default is enabled. connectionReqPath Set the path where the cwmp daemon can be reached. OPTIONAL connectionReqUserName Set the username the ACS must use to log in. OPTIONAL connectionReqPsswd Set the password the ACS must use to log in. OPTIONAL connectionReqAuth Set the digest authentication flag of the cwmp daemon.
PAGE 126
CWMP Commands cwmp server config Configure the cwmpd towards the ACS. SYNTAX: cwmp server config [url = ] [username = ] [password = ] where: url Set the HTTP URL used to contact the ACS server. OPTIONAL username Set the username for ACS Digest Authentication. OPTIONAL password Set the password for ACS Digest Authentication. OPTIONAL EXAMPLE: =>cwmp server config ACS url : 10.11.10.248 ACS username : ACS password : => 104 E-DOC-CTC-20061027-0003 v2.
PAGE 127
Debug Commands 8 Debug Commands Introduction This chapter describes the commands of the debug command group. Contents This chapter covers the following commands: debug exec E-DOC-CTC-20061027-0003 v2.0 Execute a 'Trace & Debug' command.
PAGE 128
Debug Commands debug exec Execute a 'Trace & Debug' command. ! This command is for qualified personnel only. SYNTAX: debug exec cmd = where: cmd 106 A quoted 'Trace & Debug' command string. REQUIRED E-DOC-CTC-20061027-0003 v2.
PAGE 129
DHCP Commands 9 DHCP Commands Introduction This chapter describes the commands of the Dynamic Host Configuration Protocol (DHCP) command group. Contents This chapter covers the following commands: dhcp client flush Delete all the DHCP leases. 109 dhcp client ifadd Create a DHCP client. 110 dhcp client ifattach Activate a DHCP client. 111 dhcp client ifconfig Configure a DHCP client. 112 dhcp client ifdelete Delete a DHCP client.
PAGE 130
DHCP Commands 108 dhcp relay ruledelete Delete a selection rule from a DHCP forward entry. 142 dhcp rule add Add a rule for DHCP conditional selection. 143 dhcp rule debug traceconfig Modify DHCP rule trace configuration. 144 dhcp rule delete Delete a DHCP rule. 145 dhcp rule flush Flush all DHCP rules. 146 dhcp rule list List all DHCP rules. 147 dhcp server config Print the DHCP server configuration settings. 148 dhcp server flush Flush all DHCP server pool and lease entries.
PAGE 131
DHCP Commands dhcp client flush Delete all the DHCP leases. i The flush command does not impact previously saved configurations. SYNTAX: dhcp client flush E-DOC-CTC-20061027-0003 v2.
PAGE 132
DHCP Commands dhcp client ifadd Create a DHCP client. SYNTAX: dhcp client ifadd intf = [defrqoptions = <{disabled|enabled}>] where: intf The name of the dynamic interface for which a DHCP lease must be created. REQUIRED defrqoptions Enable/Disable the creation of the default Parameter Request List. OPTIONAL EXAMPLE: =>dhcp client iflist No dynamic interfaces defined.
PAGE 133
DHCP Commands dhcp client ifattach Activate a DHCP client. SYNTAX: dhcp client ifattach intf = where: intf The name of the dynamic interface for which a DHCP client was created. REQUIRED EXAMPLE: =>dhcp client iflist myPPP_ppp : [INIT] flags = bc dns rt IP address : 0.0.0.0 HW address [SpeedTouch] : 00 DHCP server: 255.255.255.
PAGE 134
DHCP Commands dhcp client ifconfig Configure a DHCP client. i Use the command :dhcp client ifrelease before configuring the dhcp client. SYNTAX: dhcp client ifconfig intf = [label = ] [metric = ] [dnsmetric = ] [broadcast = <{disabled|enabled}>] [serverroute = ] where: intf The name of the dynamic interface to be configured. REQUIRED label Label for default gateway and static routes. OPTIONAL metric A number between 0 and 255.
PAGE 135
DHCP Commands dhcp client ifdelete Delete a DHCP client. SYNTAX: dhcp client ifdelete intf = where: intf The name of the dynamic interface for which the DHCP lease must be deleted. REQUIRED EXAMPLE: =>dhcp client iflist myPPP_ppp : [INIT] flags = bc dns rt IP address : 10.0.0.1 HW address [SpeedTouch] : 00:90:d0:01:47:f1 DHCP server: 10.10.1.
PAGE 136
DHCP Commands dhcp client ifdetach De-activate a DHCP client and releases its lease. SYNTAX: ifdetach intf = where: intf The name of the dynamic interface. REQUIRED RELATED COMMANDS: 114 dhcp client ifattach Activate a DHCP client. dhcp client ifrenew Renew the DHCP lease. dhcp client iflist List all the DHCP leases attached to dynamic interfaces. E-DOC-CTC-20061027-0003 v2.
PAGE 137
DHCP Commands dhcp client iflist List all the DHCP leases attached to dynamic interfaces. SYNTAX: dhcp client iflist [intf = ] [expand = <{disabled|enabled}>] where: intf The name of the dynamic interface. OPTIONAL expand Expand enabled/disabled. OPTIONAL EXAMPLE: =>dhcp client iflist myPPP_ppp : [INIT] flags = bc dns rt IP address : 10.0.0.1 HW address [SpeedTouch] : 00:90:d0:01:47:f1 DHCP server: 10.10.1.
PAGE 138
DHCP Commands RELATED COMMANDS: 116 dhcp client ifadd Create a DHCP client. dhcp client ifdelete Delete a DHCP client. E-DOC-CTC-20061027-0003 v2.
PAGE 139
DHCP Commands dhcp client ifrenew Renew the DHCP lease. SYNTAX: dhcp client ifrenew intf = where: intf The name of the dynamic interface for which the DHCP lease must be renewed. REQUIRED EXAMPLE 1: =>dhcp client iflist NewETHoA : [BOUND] flags= uc IP address : 10.0.0.10 HW address : 00:90:d0:01:47:f1 DHCP server : 255.255.255.255 hostname : NewLease req.
PAGE 140
DHCP Commands EXAMPLE 2: The Thomson ST is configured as DHCP client disabled its Ethernet interface eth0.
PAGE 141
DHCP Commands dhcp client debug clear Clear the DHCP client statistics.
PAGE 142
DHCP Commands dhcp client debug stats Print the DHCP client statistics.
PAGE 143
DHCP Commands dhcp client debug traceconfig Modify the DHCP client trace configuration. SYNTAX: dhcp client debug traceconfig [state = <{disabled | enabled}>] where: state Enable or disable tracing. The default is disabled. OPTIONAL EXAMPLE: =>dhcp client debug traceconfig tracing: disabled =>dhcp client debug traceconfig trace=enabled =>dhcp client debug traceconfig tracing: enabled => E-DOC-CTC-20061027-0003 v2.
PAGE 144
DHCP Commands dhcp client rqoptions add Add a DHCP Option Code to the Parameter Request List. SYNTAX: dhcp client rqoptions add intf = option = [index = ] where: intf The name of the dynamic interface. REQUIRED option The name or number of the option. OPTIONAL index The index of the option. OPTIONAL RELATED COMMANDS: 122 dhcp client iflist List all the DHCP leases attached to dynamic interfaces.
PAGE 145
DHCP Commands dhcp client rqoptions delete Delete a DHCP Option Code from the Parameter Request List. SYNTAX: dhcp client rqoptions delete intf = option = where: intf The name of the dynamic interface. REQUIRED option The name or number of the option. OPTIONAL RELATED COMMANDS: dhcp client rqoptions list E-DOC-CTC-20061027-0003 v2.0 List all DHCP Option Codes in the Parameter Request List.
PAGE 146
DHCP Commands dhcp client rqoptions list List all DHCP Option Codes in the Parameter Request List. SYNTAX: dhcp client rqoptions list [intf = ] where: intf The name of the dynamic interface. OPTIONAL RELATED COMMANDS: dhcp client rqoptions delete 124 Delete a DHCP Option Code from the Parameter Request List. E-DOC-CTC-20061027-0003 v2.
PAGE 147
DHCP Commands dhcp client rqoptions optionlist List all DHCP Option Codes that can be used in the Parameter Request List. SYNTAX: dhcp client rqoptions optionlist RELATED COMMANDS: dhcp client rqoptions add Add a DHCP Option Code to the Parameter Request List. dhcp client rqoptions list List all DHCP Option Codes in the Parameter Request List. E-DOC-CTC-20061027-0003 v2.
PAGE 148
DHCP Commands dhcp client txoptions add Add an option. SYNTAX: dhcp client txoptions add intf = option = value = [index = ] where: intf The name of the dynamic interface. REQUIRED option The name or number of the option. REQUIRED value The value of the option. REQUIRED index The index of the option.
PAGE 149
DHCP Commands dhcp client txoptions delete Delete an option. SYNTAX: dhcp client txoptions delete intf = option = where: intf The name of the dynamic interface. REQUIRED option The name or number of the option. REQUIRED RELATED COMMANDS: dhcp client txoptions list E-DOC-CTC-20061027-0003 v2.0 List all options.
PAGE 150
DHCP Commands dhcp client txoptions list List all options. SYNTAX: dhcp client txoptions list RELATED COMMANDS: dhcp client txoptions delete 128 Delete an option. E-DOC-CTC-20061027-0003 v2.
PAGE 151
DHCP Commands dhcp client txoptions optionlist Lists all DHCP Option Codes that can be used. SYNTAX: dhcp client txoptions optionlist RELATED COMMANDS: dhcp client txoptions add Add an option. dhcp client txoptions list List all options. E-DOC-CTC-20061027-0003 v2.
PAGE 152
DHCP Commands dhcp relay add Add an entry to the DHCP forward list. SYNTAX: dhcp relay add name = where: name The forward entry name. REQUIRED RELATED COMMANDS: 130 dhcp relay delete Delete an entry from the DHCP forward list. dhcp relay list List the DHCP forward list. dhcp relay modify Modify an entry from the DHCP forward list. E-DOC-CTC-20061027-0003 v2.
PAGE 153
DHCP Commands dhcp relay debug stats Show the DHCP relay statistics. SYNTAX: dhcp relay debug stats EXAMPLE: =>dhcp relay debug stats DHCP relay statistics ------------------------Client packet relayed : Server packet relayed : Bogus relay agent : Bogus giaddr recv : Corrupt agent option : Missing agent option : Bad circuit id : Missing circuit id : => 64 0 0 0 0 0 0 0 RELATED COMMANDS: dhcp relay debug traceconfig E-DOC-CTC-20061027-0003 v2.0 Modify the DHCP relay trace configuration.
PAGE 154
DHCP Commands dhcp relay debug traceconfig Modify the DHCP relay trace configuration. SYNTAX: dhcp relay debug traceconfig [state = <{disabled | enabled}>] where: state Enable or disable tracing. The default is disabled. OPTIONAL EXAMPLE: =>dhcp relay debug traceconfig Tracing: disabled => RELATED COMMANDS: dhcp relay debug stats 132 Show the DHCP relay statistics. E-DOC-CTC-20061027-0003 v2.
PAGE 155
DHCP Commands dhcp relay config Set the DHCP relay configuration settings. SYNTAX: dhcp relay config [agentinfo = <{disabled | enabled}>] [agentmismatch = <{disabled | enabled}>] where: agentinfo Set the relay agent info status (RFC3046) enabled or disabled. The default is disabled. OPTIONAL agentmismatch Forward/drop DHCP reply packet when a relay agent info mismatch is detected (RFC3046) (enabled) or not (disabled). The default is disabled.
PAGE 156
DHCP Commands dhcp relay delete Delete an entry from the DHCP forward list. SYNTAX: dhcp relay delete name = where: name The forward entry name. REQUIRED EXAMPLE: =>dhcp relay delete name = lan1_to_127.0.0.1 :dhcp relay delete name=lan1_to_127.0.0.1 => RELATED COMMANDS: 134 dhcp relay add Add an entry to the DHCP forward list. dhcp relay list List the DHCP forward list. dhcp relay modify Modify an entry from the DHCP forward list. E-DOC-CTC-20061027-0003 v2.
PAGE 157
DHCP Commands dhcp relay flush Flush the DHCP relay settings. i The flush command does not impact previously saved configurations. SYNTAX: dhcp relay flush EXAMPLE: =>dhcp relay list DHCP server Interface giaddr ------------------------------------------------------127.0.0.1 eth0 192.168.1.254 =>dhcp relay flush =>dhcp relay list No dynamic interfaces defined. => E-DOC-CTC-20061027-0003 v2.
PAGE 158
DHCP Commands dhcp relay ifconfig Configure a DHCP relay interface. SYNTAX: dhcp relay ifconfig intf = [relay = <{disabled | enabled}>] [maxhops = ] [remoteid = ] [trusted = <{disabled | enabled}>] where: 136 intf The name of the dynamic interface to be configured. REQUIRED relay Set the relay status to enabled or disabled. The default is disabled. OPTIONAL maxhops A number between 0 and 16. Represents the maximum number of hops allowed in the DHCP packet.
PAGE 159
DHCP Commands EXAMPLE: =>dhcp relay iflist eth0 : admin state = up max hops = 4 trusted = disabled Internet_trigger : admin state = down max hops = 4 trusted = disabled Internet : admin state = down max hops = 4 trusted = disabled oper state = up remote id = oper state = down remote id = oper state = down remote id = =>dhcp relay ifconfig intf=Internet_trigger relay=enabled trusted=enabled =>dhcp relay iflist eth0 : admin state = up oper state = up max hops = 4 trusted = disabled remote id = Internet_t
PAGE 160
DHCP Commands dhcp relay iflist Show the configuration of the relay interfaces. SYNTAX: dhcp relay iflist [intf = ] where: intf The name of the dynamic interface to be listed. Note OPTIONAL If not specified, all the relay interfaces will be shown.
PAGE 161
DHCP Commands dhcp relay list List the DHCP forward list. SYNTAX: dhcp relay list [name = ] where: name The forward entry name. OPTIONAL EXAMPLE: =>dhcp relay list DHCP server Interface giaddr ------------------------------------------------------127.0.0.1 eth0 10.0.0.138 => RELATED COMMANDS: dhcp relay add Add an entry to the DHCP forward list. dhcp relay delete Delete an entry from the DHCP forward list. dhcp relay modify Modify an entry from the DHCP forward list.
PAGE 162
DHCP Commands dhcp relay modify Modify an entry from the DHCP forward list. SYNTAX: dhcp relay modify name = [addr = ] [intf = <{None | guest1 | dmz1 | wan1 | lan1 | Internet}>] [giaddr = ] [script = <>] where: name The forward entry name. REQUIRED addr The DHCP server IP address. OPTIONAL intf The name of the relay interface, ‘None’ to indicate no interface is specified. The standard is None. OPTIONAL giaddr The giaddr field to be used in relayed DHCP packets.
PAGE 163
DHCP Commands dhcp relay ruleadd Add a selection rule to a DHCP forward entry. SYNTAX: dhcp relay ruleadd name = [key = <{or | and}>] rulename = where: name The name of the forward entry. REQUIRED key The logical key of the selection rule. The default is or. OPTIONAL rulename The name of the DHCP selection rule. REQUIRED RELATED COMMANDS: dhcp relay ruledelete E-DOC-CTC-20061027-0003 v2.0 Delete a selection rule from a DHCP forward entry.
PAGE 164
DHCP Commands dhcp relay ruledelete Delete a selection rule from a DHCP forward entry. SYNTAX: dhcp relay ruledelete name = rulename = where: name The name of the forward entry. REQUIRED rulename The name of the DHCP selection rule. REQUIRED RELATED COMMANDS: dhcp relay ruleadd 142 Add a selection rule to a DHCP forward entry. E-DOC-CTC-20061027-0003 v2.
PAGE 165
DHCP Commands dhcp rule add Add a rule for DHCP conditional selection. SYNTAX: dhcp rule add i name = type = <{vci | uci | mac}> vci [!]= uci [!]= [match = <{exactly|as_substring}>] mac [!]= If a value is preceded by a “!”, it means NOT. For example “mac=!00:9f:aa:bb:cc:dd” means “for MAC address different from 00:9f:aa:bb:cc:dd”. where: name The name of the new DHCP rule.
PAGE 166
DHCP Commands dhcp rule debug traceconfig Modify DHCP rule trace configuration. SYNTAX: dhcp rule debug traceconfig [state = {disabled | enabled}] where: state 144 Set tracing to disabled or enabled. The default is disabled. OPTIONAL E-DOC-CTC-20061027-0003 v2.
PAGE 167
DHCP Commands dhcp rule delete Delete a DHCP rule. SYNTAX: dhcp rule delete name = where: name The name of the DHCP rule. REQUIRED EXAMPLE: =>dhcp rule delete name = new :dhcp rule delete name=new => RELATED COMMANDS: dhcp rule add Add a rule for DHCP conditional selection. dhcp rule flush Flush all DHCP rules. dhcp rule list List all DHCP rules. E-DOC-CTC-20061027-0003 v2.
PAGE 168
DHCP Commands dhcp rule flush Flush all DHCP rules. SYNTAX: dhcp rule flush EXAMPLE: =>dhcp rule list Name new =>dhcp rule flush =>dhcp rule list Name => Use 0 Value vci=test Use Value RELATED COMMANDS: 146 dhcp rule add Add a rule for DHCP conditional selection. dhcp rule delete Delete a DHCP rule. dhcp rule list List all DHCP rules. E-DOC-CTC-20061027-0003 v2.
PAGE 169
DHCP Commands dhcp rule list List all DHCP rules. SYNTAX: dhcp rule list EXAMPLE: =>dhcp rule list Name new => Use 0 Value vci=test RELATED COMMANDS: dhcp rule add Add a rule for DHCP conditional selection. dhcp rule delete Delete a DHCP rule. dhcp rule flush Flush all DHCP rules. E-DOC-CTC-20061027-0003 v2.
PAGE 170
DHCP Commands dhcp server config Print the DHCP server configuration settings. SYNTAX: dhcp server config [state = <{disabled | enabled}>] where: 148 E-DOC-CTC-20061027-0003 v2.
PAGE 171
DHCP Commands dhcp server flush Flush all DHCP server pool and lease entries. i The flush command does not impact previously saved configurations. SYNTAX: dhcp server flush E-DOC-CTC-20061027-0003 v2.
PAGE 172
DHCP Commands dhcp server policy Print the DHCP server policy settings. SYNTAX: dhcp server policy [verifyfirst = ] [trustclient = ] [rtbehaviour = ] where: 150 E-DOC-CTC-20061027-0003 v2.
PAGE 173
DHCP Commands dhcp server debug clear Clear the DHCP server statistics.
PAGE 174
DHCP Commands dhcp server debug stats Show the DHCP server statistics.
PAGE 175
DHCP Commands > Ping table got full: whether the history list of IP address pings got full or not. These pings are sent by the DHCP server to verify whether the IP address is already in use disabled the LAN or not (:dhcp server policy verifyfirst=yes). > Second DHCP server seen: whether a concurrent DHCP server was found disabled the LAN or not. RELATED COMMANDS: dhcp server debug clear E-DOC-CTC-20061027-0003 v2.0 Clear the DHCP server statistics.
PAGE 176
DHCP Commands dhcp server debug traceconfig Modify the DHCP server trace configuration. SYNTAX: dhcp server debug traceconfig [state = <{disabled | enabled}>] where: state Enable or disable tracing. The default is disabled. OPTIONAL EXAMPLE: =>dhcp server debug traceconfig Tracing: disabled => 154 E-DOC-CTC-20061027-0003 v2.
PAGE 177
DHCP Commands dhcp server lease add Add a DHCP server lease. SYNTAX: dhcp server lease add clientid = pool = [addr = ] [offset = ] [leasetime = ] [expirytime = ] [gateway = ] [macaddr = ] where: clientid The DHCP client identification string of the booting host. REQUIRED pool The name of the DHCP server pool from which the DHCP lease should be taken.
PAGE 178
DHCP Commands EXAMPLE: =>dhcp server Lease 0 0.0.0.0 =>dhcp server =>dhcp server Lease 0 0.0.0.0 1 10.0.0.1 => lease list Pool TTL State dhcp_pool_1 00:26:40 FREE lease add clientid=01:23:55:67:89:ab lease list Pool TTL State dhcp_pool_1 00:26:40 FREE local_pool 00:59:22 USED Clientid 00:90:D0:12:34:56 pool=Local_pool leasetime=3600 Clientid 00:90:D0:12:34:56 01:23:45:67:89:AB RELATED COMMANDS: 156 dhcp server lease delete Delete a DHCP server lease.
PAGE 179
DHCP Commands dhcp server lease delete Delete a DHCP server lease. SYNTAX: dhcp server lease delete [clientid = ] [index = ] where: clientid The DHCP client identification string of the DHCP lease. Note index OPTIONAL If not specified, all DHCP clients are deleted. The DHCP server lease table index. OPTIONAL Use the command :dhcp server lease list to obtain a list of the index numbers of all current DHCP leases. Tip EXAMPLE: =>dhcp server Lease 0 0.0.0.0 1 10.0.0.
PAGE 180
DHCP Commands dhcp server lease flush Flush all the DHCP server leases. i The flush command does not impact previously saved configurations. SYNTAX: dhcp server lease flush [pool = ] where: pool The name of the DHCP server pool to be flushed. Only the leases belonging to this pool will be deleted. Note OPTIONAL If not specified, all the DHCP server leases will be flushed. EXAMPLE: =>dhcp server Lease 0 0.0.0.0 1 10.0.0.1 2 10.0.0.101 3 10.0.0.132 5 10.0.0.5 4 10.0.0.6 8 10.0.0.8 9 10.0.0.
PAGE 181
DHCP Commands dhcp server lease list List all the DHCP server leases. SYNTAX: dhcp server lease list [clientid = ] [index = ] where: clientid The DHCP client identification string of the DHCP lease. Note index If not specified, the DSHCP server leases for all the DHCP clients are listed. The DHCP server lease table index. Note OPTIONAL OPTIONAL If not specified, the complete DHCP server lease table will be shown. EXAMPLE: =>dhcp server Lease 0 0.0.0.0 1 10.0.0.1 2 10.0.
PAGE 182
DHCP Commands dhcp server option flush Flush all DHCP server option templates and instances. i The flush command does not impact previously saved configurations. SYNTAX: dhcp server option flush 160 E-DOC-CTC-20061027-0003 v2.
PAGE 183
DHCP Commands dhcp server option instadd Add a DHCP server option instance. SYNTAX: dhcp server option instadd name = tmplname = value = where: name The name of the DHCP server option instance. REQUIRED tmplname The name of the DHCP server option template. REQUIRED Tip value The value of the DHCP server option instance.
PAGE 184
DHCP Commands EXAMPLE: =>dhcp server option instlist myInstance Tmpl name : myTmpl Use : 0 Value : (32-bit)64 (1) =>dhcp server option instadd name=yourInstance tmplname=yourTmpl value=(ascii)! {root}[dhcp server option]=>instlist yourInstance Tmpl name : yourTmpl (2) Use : 0 Value : (ascii)! myInstance Tmpl name : myTmpl Use : 0 Value : (32-bit)64 (1) => RELATED COMMANDS: 162 dhcp server option instdelete Delete a DHCP server option instance.
PAGE 185
DHCP Commands dhcp server option instdelete Delete a DHCP server option instance. SYNTAX: dhcp server option instdelete name = where: name The name of the DHCP server option instance to be deleted.
PAGE 186
DHCP Commands dhcp server option instlist List all the DHCP server option instances. SYNTAX: dhcp server option instlist EXAMPLE: =>dhcp server option instlist yourInstance Tmpl name : yourTmpl Use : 0 Value : (ascii)! myInstance Tmpl name : myTmpl Use : 0 Value : (32-bit)64 (2) (1) => RELATED COMMANDS: 164 dhcp server option instadd Add a DHCP server option instance. dhcp server option instdelete Delete a DHCP server option instance. E-DOC-CTC-20061027-0003 v2.
PAGE 187
DHCP Commands dhcp server option tmpladd Add a DHCP server option template. SYNTAX: dhcp server option tmpladd name = optionid = type = <{8-bit | 16-bit | 32-bit | addr | ascii | byte_array}> where: name The name of the DHCP server option template. REQUIRED optionid A number between 1 and 254. Specifies the DHCP server option code. REQUIRED type Specifies the DHCP server option type. Choose between: REQUIRED > > > > > > 8-bit 16-bit 32-bit addr ascii byte_array.
PAGE 188
DHCP Commands dhcp server option tmpldelete Delete a DHCP server option template. SYNTAX: dhcp server option tmpldelete name = where: name The name of the DHCP server option template to be deleted.
PAGE 189
DHCP Commands dhcp server option tmpllist List all the DHCP server option templates. SYNTAX: dhcp server option tmpllist EXAMPLE: =>dhcp server option tmpllist Name Option Type yourTmpl 2 ascii myTmpl 1 32-bit => Use 0 0 RELATED COMMANDS: dhcp server option tmpladd Add a DHCP server option template. dhcp server option tmpldelete Delete a DHCP server option template. E-DOC-CTC-20061027-0003 v2.
PAGE 190
DHCP Commands dhcp server pool add Add a DHCP server pool. SYNTAX: dhcp server pool add name = [index = ] where: name The name of the DHCP server pool. Note index If not specified, the name is “dhcp_pool_x”, where x is a subsequent number. The number of the pool before which you want the new pool to be added. Note 168 REQUIRED OPTIONAL If not specified, the DHCP server pool will be added at the bottom of the DHCP server lease table. E-DOC-CTC-20061027-0003 v2.
PAGE 191
DHCP Commands EXAMPLE: =>dhcp server pool list Pool Start End 0 dhcp_pool_1 0.0.0.0 0.0.0.0 1 My_LAN_Pool 10.0.0.1 10.0.0.254 2 dhcp_pool_2 0.0.0.0 0.0.0.0 =>dhcp server pool add =>dhcp server pool list Pool Start End 0 dhcp_pool_1 0.0.0.0 0.0.0.0 1 My_LAN_Pool 10.0.0.1 10.0.0.254 2 dhcp_pool_2 0.0.0.0 0.0.0.0 3 dhcp_pool_3 0.0.0.0 0.0.0.0 =>dhcp server pool add name=POOL_EXTRA1 =>dhcp server pool list Pool Start End 0 dhcp_pool_1 0.0.0.0 0.0.0.0 1 My_LAN_Pool 10.0.0.1 10.0.0.254 2 dhcp_pool_2 0.0.0.0 0.0.
PAGE 192
DHCP Commands dhcp server pool config Configure a DHCP server pool.
PAGE 193
DHCP Commands gateway The IP address of the default gateway for the DHCP clients. The default value of this parameter is 0 (not specified), which means that the gateway IP address will be communicated by the remote server as soon as the PPP IPCP subnetmasking connection is established or that the Thomson ST acts as the LAN default gateway. OPTIONAL server The IP address of the DHCP server for DHCP clients. OPTIONAL primdns The IP address of the primary DNS server for the DHCP clients.
PAGE 194
DHCP Commands dhcp server pool delete Delete a DHCP server pool. SYNTAX: dhcp server pool delete name = where: name The name of the DHCP server pool to be deleted. Tip REQUIRED Use the command :dhcp server pool list to obtain a list of all current DHCP leases. EXAMPLE: =>dhcp server pool list Pool Start End 0 LAN_Private 10.0.0.1 10.0.0.254 1 My_Pool 192.6.11.101 192.6.11.254 =>dhcp server pool delete name=My_Pool =>dhcp server pool list Pool Start End 0 LAN_Private 10.0.0.1 10.0.0.
PAGE 195
DHCP Commands dhcp server pool flush Flush all DHCP server pools. i The flush command does not impact previously saved configurations. SYNTAX: dhcp server pool flush EXAMPLE: =>dhcp server pool list Pool Start 0 LAN_Private 10.0.0.1 1 My_Pool 192.6.11.101 =>dhcp server pool flush =>dhcp server pool list => E-DOC-CTC-20061027-0003 v2.0 End 10.0.0.254 192.6.11.
PAGE 196
DHCP Commands dhcp server pool list List all DHCP server pools. SYNTAX: dhcp server pool list [name = ] where: name The name of the DHCP server pool to be shown. Note OPTIONAL If not specified, all the DHCP server pools are shown. EXAMPLE: =>dhcp server pool list Pool Start 0 LAN_Private 10.0.0.1 1 My_Pool 192.6.11.101 => End 10.0.0.254 192.6.11.254 Intf eth0 eth0 State USED USED RELATED COMMANDS: 174 dhcp server pool add Add a DHCP server pool.
PAGE 197
DHCP Commands dhcp server pool optadd Add an option instance to the DHCP server pool. SYNTAX: dhcp server pool optadd name = instname = where: name The name of the DHCP server pool to which an option instance must be added. REQUIRED instname The name of the DHCP server option instance. REQUIRED Tip Use the command :dhcp server option instlist to obtain a list of DHCP server option instances.
PAGE 198
DHCP Commands dhcp server pool optdelete Delete an option instance from the DHCP server pool. SYNTAX: dhcp server pool optdelete name = instname = where: name The name of the DHCP server pool from which an option instance must be deleted. REQUIRED instname The name of the DHCP server option instance to be deleted. REQUIRED Tip 176 Use the command :dhcp server option list to obtain a list of DHCP server option instances. E-DOC-CTC-20061027-0003 v2.
PAGE 199
DHCP Commands EXAMPLE: =>dhcp server pool list name=dhcp_pool_1 Pool Start End 1 dhcp_pool_1 0.0.0.0 0.0.0.0 DHCP server Netmask Leasetime Gateway DNS domain DNS metric = = = = = = Intf lan1 State FREE 0.0.0.0 [unnumbered] 0.0.0.0 infinite 0.0.0.0 lan 0 DNS address list: 0.0.0.0 (local DNS) Option instance list: Name Option yourInstance 2 (yourTmpl) =>dhcp server pool optdelete name=dhcp_pool_1 instname=yourInstance =>dhcp server pool list name=dhcp_pool_1 Pool Start End Intf State 1 dhcp_pool_1 0.0.
PAGE 200
DHCP Commands dhcp server pool rtadd Add a route to the DHCP server pool. SYNTAX: dhcp server pool rtadd name = dst = [dstmsk = ] [gateway = ] where: name The name of the DHCP server pool to which a route must be added. REQUIRED dst The IP destination address of the route for DHCP clients. REQUIRED dstmsk The destination IP address mask. OPTIONAL gateway The IP address of the next hop.
PAGE 201
DHCP Commands dhcp server pool rtdelete Delete a route from the DHCP server pool. SYNTAX: dhcp server pool rtdelete name = dst = [dstmsk = ] [gateway = ] where: name The name of the DHCP server pool from which a route must be deleted. REQUIRED dst The IP destination address of the route for DHCP clients. REQUIRED dstmsk The destination IP address mask. OPTIONAL gateway The IP address of the next hop.
PAGE 202
DHCP Commands dhcp server pool ruleadd Add a selection rule to the DHCP server pool. SYNTAX: dhcp server pool ruleadd name = [key = {or | and}] rulename = where: name The name of the DHCP server pool to which a selection rule must be added. REQUIRED key The logical key of the selection rule. The default is or. OPTIONAL The name of the DHCP selection rule. REQUIRED rulename Tip Use the command :dhcp server rule list to obtain a list of DHCP server rules.
PAGE 203
DHCP Commands dhcp server pool ruledelete Delete a selection rule from the DHCP server pool. SYNTAX: dhcp server pool ruleadd name = rulename = where: name The name of the DHCP server pool from which a selection rule must be deleted. REQUIRED rulename The name of the DHCP selection rule to be deleted. REQUIRED Tip Use the command :dhcp server rule list to obtain a list of DHCP server rules. RELATED COMMANDS: dhcp server pool ruleadd E-DOC-CTC-20061027-0003 v2.
PAGE 204
DHCP Commands 182 E-DOC-CTC-20061027-0003 v2.
PAGE 205
DNS Commands 10 DNS Commands Introduction This chapter describes the commands of the dns command group. Contents This chapter covers the following commands: dns client config Modify the Domain Name System (DNS) resolver configuration. 184 dns client dnsadd Add a DNS server. 185 dns client dnsdelete Delete a DNS server. 186 dns client dnslist List all DNS servers. 187 dns client flush Remove all DNS servers. 188 dns client nslookup DNS lookup for a domain name or an address.
PAGE 206
DNS Commands dns client config Modify the Domain Name System (DNS) resolver configuration. SYNTAX: dns client config [timeout = ] [retry = ] [search = <{disabled | enabled}>] [list = ] [trace = <{disabled | enabled}>] where: timeout A number between 1 and 900 (seconds). Represents the query timeout. The default is 5. OPTIONAL retry A number between 0 and 10. Represents the number of query retries before giving up. The default is 3.
PAGE 207
DNS Commands dns client dnsadd Add a DNS server. SYNTAX: dns client dnsadd addr = [port = ] where: addr The IP address of the DNS server to be added. REQUIRED port The DNS server port number. The default is 53. OPTIONAL EXAMPLE: =>dns client dnsadd addr=150.150.150.150 =>dns client dnslist Entry 1 2 State CONNECTED CONNECTED Family IP IP Server [port] 53 - [addr] 127.0.0.1 [port] 53 - [addr] 150.150.150.150 => RELATED COMMANDS: dns client dnsdelete Delete a DNS server.
PAGE 208
DNS Commands dns client dnsdelete Delete a DNS server. SYNTAX: dns client dnsdelete index = where: index A number between 1 and 99. Represents the index number of the DNS server to be deleted. Tip REQUIRED Use the command :dns client dnslist to obtain a list of DNS servers. EXAMPLE: =>dns client dnslist Entry 1 2 State CONNECTED CONNECTED Family IP IP Server [port] 53 - [addr] 127.0.0.1 [port] 53 - [addr] 150.150.150.
PAGE 209
DNS Commands dns client dnslist List all DNS servers. SYNTAX: dns client dnslist EXAMPLE: =>dns client dnslist Entry 1 2 State CONNECTED CONNECTED Family IP IP Server [port] 53 - [addr] 127.0.0.1 [port] 53 - [addr] 150.150.150.150 => RELATED COMMANDS: dns client dnsadd Add a DNS server. dns client dnsdelete Delete a DNS server. E-DOC-CTC-20061027-0003 v2.
PAGE 210
DNS Commands dns client flush Remove all DNS servers. SYNTAX: dns client flush 188 E-DOC-CTC-20061027-0003 v2.
PAGE 211
DNS Commands dns client nslookup DNS lookup for a domain name or an address. SYNTAX: dns client nslookup host = where: host E-DOC-CTC-20061027-0003 v2.0 The DNS domain name string for which to query.
PAGE 212
DNS Commands dns server config Modify the DNS resolver configuration. SYNTAX: dns server config [domain = ] [timeout = ] [suppress = ] [state = <{disabled | enabled}>] [trace = <{disabled | enabled}>] [WANDownSpoofing = <{disabled | enabled}>] [WDSpoofedIP = ] where: domain The DNS server domain name. OPTIONAL timeout A number between 0 and 2147483647 (seconds). Represents the forwarded DNS query timeout. The default is 15.
PAGE 213
DNS Commands dns server flush Flush all local DNS hosts and routes. SYNTAX: dns server flush E-DOC-CTC-20061027-0003 v2.
PAGE 214
DNS Commands dns server debug clear Clear the DNS server/forwarder statistics.
PAGE 215
DNS Commands dns server debug stats Print the DNS server/forwarder statistics. SYNTAX: dns server debug stats EXAMPLE: =>dns server debug stats Corrupted packets received Local questions resolved Local negative answers sent Total DNS packets forwarded External answers received Spoofed responses Forward table full, discard Spurious answers Unknown query types => : : : : : : : : : 100 3 1 0 0 0 0 0 0 RELATED COMMANDS: dns server debug clear E-DOC-CTC-20061027-0003 v2.
PAGE 216
DNS Commands dns server debug spoof clear Clear the intercept cache table SYNTAX: dns server debug spoof clear RELATED COMMANDS: 194 dns server debug spoof getaddress Get the real ip for the given spoofed ip dns server debug spoof getflags Get the error flags for the given spoofed ip dns server debug spoof list List the intercept cache table. dns server debug spoof update Update the intercept cache table. E-DOC-CTC-20061027-0003 v2.
PAGE 217
DNS Commands dns server debug spoof getaddress Get the real ip for the given spoofed ip SYNTAX: dns server debug spoof getaddress addr = where: addr The IP address of the spoofed server. REQUIRED EXAMPLE: {Administrator}=>dns server debug spoof getaddress addr=198.18.1.1 :dns server debug spoof getaddress addr=198.18.1.1 Resolved ip = 0.0.0.0.
PAGE 218
DNS Commands dns server debug spoof getflags Get the error flags for the given spoofed ip SYNTAX: dns server debug spoof getflags addr = where: addr The IP address of the spoofed server. REQUIRED EXAMPLE: {Administrator}[dns server debug spoof]=>:dns server debug spoof getflags addr = 192.168.1.254 :dns server debug spoof getflags addr=192.168.1.254 Invalid spoofed ip.
PAGE 219
DNS Commands dns server debug spoof list List the intercept cache table. SYNTAX: dsn server debug spoof list EXAMPLE: {Administrator}[dns server debug spoof]=>list Spoof IP FQDN 198.18.1.1 eu.thmulti.com 198.18.1.2 thmulti.com 198.18.1.3 com 198.18.1.4 edgmd588.eu.thmulti.com 198.18.1.5 edgmssus01.eu.thmulti.com 198.18.1.6 BOULSDCEU02.eu.thmulti.com 198.18.1.7 juleke.nit Real IP 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.
PAGE 220
DNS Commands dns server debug spoof update Update the intercept cache table. SYNTAX: dns server debug spoof update EXAMPLE: {Administrator}=>dns server debug spoof update {Administrator}=> RELATED COMMANDS: 198 dns server debug spoof clear Clear the intercept cache table dns server debug spoof getaddress Get the real ip for the given spoofed ip dns server debug spoof getflags Get the error flags for the given spoofed ip dns server debug spoof list List the intercept cache table.
PAGE 221
DNS Commands dns server host add Add a local DNS host. SYNTAX: dns server host add name = [addr = ] [ttl = ] where: name The name of the IP host to be added. REQUIRED addr The IP address of the host. OPTIONAL ttl A number between 0 and 2147483647 (seconds). Represents the lifetime of the host. The default is 0 (in other words, no limit on the lifetime). OPTIONAL EXAMPLE: =>dns server host add name=myDNS addr=150.150.150.
PAGE 222
DNS Commands dns server host delete Delete a local DNS host. SYNTAX: dns server host delete name = where: name The name of the DNS host to be deleted. REQUIRED EXAMPLE: =>dns server host list Address Hostname 150.150.150.150 myDNS speedtouch dsldevice =>dns server host delete name=myDNS =>dns server host list Address Hostname speedtouch dsldevice => TTL (s) 3600 0 0 TTL (s) 0 0 RELATED COMMANDS: 200 dns server host add Add a local DNS host.
PAGE 223
DNS Commands dns server host flush Flush all the local DNS hosts. SYNTAX: dns server host flush EXAMPLE: =>dns server host list Address Hostname 192.168.1.64 * Unknown-00-10-a4-ad-32-cf dsldevice speedtouch =>dns server host flush =>dns server host list => E-DOC-CTC-20061027-0003 v2.
PAGE 224
DNS Commands dns server host list List all the local DNS hosts. SYNTAX: dns server host list EXAMPLE: =>dns server host list Address Hostname 192.168.1.64 * Unknown-00-10-a4-ad-32-cf dsldevice speedtouch => TTL (s) 60 1200 1200 RELATED COMMANDS: 202 dns server host add Add a local DNS host. dns server host delete Delete a local DNS host. E-DOC-CTC-20061027-0003 v2.
PAGE 225
DNS Commands dns server route add Creates a DNS forwarding entry or template. SYNTAX: dns server route add dns = [src = ] [srcmask = ] [domain = ] [metric = ] [intf = ] where: dns The IP address of a DNS server. If 0.0.0.0 is used, the entry becomes a DNS-Template which is instantiated if DNS Server IPs are configured on an IP interface. REQUIRED src The source IP address(es) using this remote DNS server.
PAGE 226
DNS Commands EXAMPLE: =>dns server route add dns=150.150.150.150 src=10.0.0.0/8 domain=myDNS intf=eth0 =>dns server route list DNS Server Source Domain Metric Intf State 150.150.150.150 10.0.0.0/8 myDNS 0 eth0 UP => RELATED COMMANDS: 204 dns server route delete Delete a DNS forwarding route. dns server route list List all the DNS forwarding routes. E-DOC-CTC-20061027-0003 v2.
PAGE 227
DNS Commands dns server route delete Deletes a DNS forwarding entry or template SYNTAX: dns server route delete dns = [domain = ] [intf = <{loop|Internet|LocalNetwork}>] where: dns The IP address of the DNS server for which the forwarding route must be deleted. REQUIRED domain The DNS domain string. OPTIONAL intf The interface associated with the DNS entry or DNS Template. OPTIONAL EXAMPLE: =>dns server route list DNS Server Source Domain 150.150.150.150 10.0.0.
PAGE 228
DNS Commands dns server route flush Removes all DNS forwarding entries and templates. SYNTAX: dns server route flush EXAMPLE: =>dns server route list DNS Server Source 150.150.150.150 10.0.0.0/8 =>dns server route flush =>dns server route list => 206 Domain myDNS Metric 0 Intf eth0 State UP E-DOC-CTC-20061027-0003 v2.
PAGE 229
DNS Commands dns server route list List all the DNS forwarding entries or templates. SYNTAX: dns server route list EXAMPLE: =>dns server route list DNS Server Source 150.150.150.150 10.0.0.0/8 => Domain myDNS Metric 0 Intf eth0 State UP RELATED COMMANDS: dns server route add Adds a DNS forwarding route. dns server route delete Delete a DNS forwarding route. E-DOC-CTC-20061027-0003 v2.
PAGE 230
DNS Commands 208 E-DOC-CTC-20061027-0003 v2.
PAGE 231
DSD Commands 11 DSD Commands Introduction This chapter describes the commands of the dsd command group. Contents This chapter covers the following commands: dsd config Display/modify the Differentiated Service Delivery (DSD) framework configuration. 210 dsd debug config Display/modify DSD debug settings 211 dsd debug connection list Display the internal connection pool usage. 212 dsd debug proxy Display/modify the HyperText Transfer Protocol (HTTP) Intercept fixed proxy configuration.
PAGE 232
DSD Commands dsd config Display/modify the Differentiated Service Delivery (DSD) framework configuration. SYNTAX: dsd config [state = <{disabled | enabled | automatic}>] where: state i Choose between: OPTIONAL > automatic (default): By default (DSD config state is automatic), the DSD framework is not active, for example no URL filtering or web site filtering is applied.
PAGE 233
DSD Commands dsd debug config Display/modify DSD debug settings SYNTAX: config [turbomode = <{disabled|enabled}>] where: turbomode E-DOC-CTC-20061027-0003 v2.
PAGE 234
DSD Commands dsd debug connection list Display the internal connection pool usage. SYNTAX: dsd debug connection list [expand = <{disabled|enabled}>] where: expand 212 Enable or disable the expanded listing. The default is disabled. optional E-DOC-CTC-20061027-0003 v2.
PAGE 235
DSD Commands dsd debug proxy Display/modify the HyperText Transfer Protocol (HTTP) Intercept fixed proxy configuration. SYNTAX: dsd debug proxy [state = <{disabled | enabled}>] [dest = ] [port = <{supported TCP/UDP port} or number>] where: state Enable or disable fixed proxy redirecting. The default is disabled. OPTIONAL dest The destination IP address to which requests will be forwarded. OPTIONAL port The port to be used for connecting to proxy.
PAGE 236
DSD Commands dsd debug recycling Display/modify HTTPI recycling settings SYNTAX: dsd debug recycling state = | interval = httpidle = otheridle = where: 214 state Enable/disable stream recycling OPTIONAL interval Time between successive activity checks OPTIONAL httpidle Minimal idle count for recycling (filtered) http streams OPTIONAL otheridle Minimal idle count for recycling other streams OPTIONAL E-DOC-CTC-20061027-0003 v2.
PAGE 237
DSD Commands dsd debug stats Display/clear DSD framework and module statistics SYNTAX: dsd debug stats name = <{intercept|urlfilter|recycling|syslog|all} clear = <{no|yes}> where: name Specify the name of a module REQUIRED clear Clear the specified statistics REQUIRED E-DOC-CTC-20061027-0003 v2.
PAGE 238
DSD Commands dsd intercept config Display/modify the HTTP Intercept configuration. SYNTAX: dsd intercept config [WDSpoofedIP = ] [servertimeout = ] [servererrorurl = ] [categoryerrorurl = ] [monitorintercepturl = ] [urlblockedurl = ] [imageredirect = <{disabled | enabled}>] [imageredirecturl = ] [alwaysuseip = <{disabled | enabled}>] where: WDSpoofedIP The IP address indicating unavailable WAN connection. The default is 198.18.1.1.
PAGE 239
DSD Commands dsd syslog config Display/modify the HTTP Intercept logging configuration. SYNTAX: dsd syslog config [syslog = <{none | unauthorized | errors | intercepted | all}>] where: syslog Define the type of events to log. Choose between: > > none: nothing is logged to syslog. > errors: only the HTTP requests that are blocked because of Server errors, Category errors, Monitor intercept, loop detection, bad requests or redirects by local policy rules.
PAGE 240
DSD Commands dsd syslog list Display the HTTP Intercept log file. SYNTAX: dsd syslog list EXAMPLE: =>dsd syslog list <86> SysUpTime: 00:22:37 [HTTPI] src=10.0.0.1 src_port=1965 dst=141.11.196.35 dst_port=80 eve nt=ServerConnect dst_name=aWebsite.com/icons/Button_Document.gif <86> SysUpTime: 00:22:59 [HTTPI] src=10.0.0.1 src_port=1968 dst=141.11.234.60 dst_port=80 eve nt=ServerConnect dst_name=anotherWebsite.com/rawgen.
PAGE 241
DSD Commands dsd urlfilter config Display/modify the URL filtering configuration. SYNTAX: dsd urlfilter config [state = <{disabled | enabled}>] [blockproxy = <{disabled | enabled}>] [blockipaddress = <{disabled | enabled}>] [blockobscuredip = <{disabled | enabled}>] [defaultaction = <{block | accept}>] where: state Enable or disable URL filtering. The default is enabled. OPTIONAL blockproxy Enable or disable blocking of HTTP requests via a proxy server. The default is disabled.
PAGE 242
DSD Commands dsd urlfilter rule add Add a rule. SYNTAX: dsd urlfilter rule add url = action = <{block | accept | redirect}> redirect = where: url Definition of the URL filter. REQUIRED action The action to perform when URL matches URL. Choose between: REQUIRED > > > redirect block accept redirect. The redirection URL. Note REQUIRED This parameter is only required when the action is redirect. EXAMPLE: =>dsd urlfilter rule add url=www.speedtouch.
PAGE 243
DSD Commands dsd urlfilter rule delete Delete a rule. SYNTAX: dsd urlfilter rule delete index = [url = ] where: index Insertion position in the list. Tip url REQUIRED Use the command :dsd urlfilter rule list to obtain the index number of the rule to be deleted. Definition of the URL filter. OPTIONAL EXAMPLE: =>dsd urlfilter rule list Index Action Url Redirect ----- ------ --- -------- 0 redirect www.speedtouch.com www.speedtouch.be 1 accept www.baen.
PAGE 244
DSD Commands dsd urlfilter rule flush Remove all current rules. SYNTAX: dsd urlfilter rule flush EXAMPLE: =>dsd urlfilter rule list Index Action Url Redirect ----- ------ --- -------- 0 redirect www.speedtouch.com www.speedtouch.be 1 accept www.baen.com Rule list statistics : 2 present, 128 total (0.0% used) =>dsd urlfilter rule flush =>dsd urlfilter rule list Index Action Url Redirect ----- -------- ------ --- Rule list statistics : 0 present, 128 total (0.
PAGE 245
DSD Commands dsd urlfilter rule list Display the list of current rules. SYNTAX: dsd urlfilter rule list EXAMPLE: =>dsd urlfilter rule list Index Action Url Redirect ----- ------ --- -------- 0 redirect www.speedtouch.com www.speedtouch.be 1 accept www.baen.com Rule list statistics : 2 present, 128 total (0.0% used) => RELATED COMMANDS: dsd urlfilter rule add Add a rule. dsd urlfilter rule delete Delete a rule. E-DOC-CTC-20061027-0003 v2.
PAGE 246
DSD Commands dsd urlfilter rule modify Modify an existing rule. SYNTAX: dsd urlfilter rule modify index = [newurl = ] action = <{block | accept | redirect}> redirect = where: index Insertion position in the list. REQUIRED newurl Definition of the new URL filter. OPTIONAL action Action to perform when URL matches URL. Choose between: REQUIRED > > > redirect block accept redirect. The redirection URL.
PAGE 247
DSD Commands EXAMPLE: =>dsd urlfilter rule list Index Action Url Redirect ----- ------ --- -------- 0 redirect www.speedtouch.com www.speedtouch.be 1 accept www.baen.com Rule list statistics : 2 present, 128 total (0.0% used) =>dsd urlfilter rule modify index=0 newurl=www.speed*.* action=redirect redirect=www.speedtou ch.be =>dsd urlfilter rule list Index Action Url Redirect ----- ------ --- -------- 0 redirect www.speed*.* www.speedtouch.be 1 accept www.baen.
PAGE 248
DSD Commands 226 E-DOC-CTC-20061027-0003 v2.
PAGE 249
DynDNS Commands 12 DynDNS Commands Introduction Dynamic DNS is a service that allows to bind a host name to an IP address. In contrast to classical DNS, this service allows regular updates of the IP address related to a host name. In this way, hosts of which the IP address regularly changes (for example due to a limited DHCP lease time) can be identified by a static host name that is unique throughout the Internet. This chapter describes the commands of the dyndns commnd group.
PAGE 250
DynDNS Commands dyndns add Add a dynamic DNS client. SYNTAX: dyndns add name = where: name The name of the new dynamic DNS client. Note REQUIRED A maximum of 5 clients can be configured. EXAMPLE: =>dyndns add name=WAN =>dyndns list WAN : [INIT] user = password = addr = 0.0.0.0 => RELATED COMMANDS: 228 dyndns delete Delete a dynamic DNS client. dyndns list List all dynamic DNS clients. E-DOC-CTC-20061027-0003 v2.
PAGE 251
DynDNS Commands dyndns delete Delete a dynamic DNS client. SYNTAX: dyndns delete name = where: name The name of the dynamic DNS client to be deleted. REQUIRED EXAMPLE: =>dyndns list WAN : [INIT] user = password = addr = 0.0.0.0 =>dyndns delete name=WAN =>dyndns list => RELATED COMMANDS: dyndns add Add a dynamic DNS client. dyndns list List all dynamic DNS clients. E-DOC-CTC-20061027-0003 v2.
PAGE 252
DynDNS Commands dyndns flush Delete all the dynamic DNS clients. SYNTAX: dyndns flush 230 E-DOC-CTC-20061027-0003 v2.
PAGE 253
DynDNS Commands dyndns list List all the dynamic DNS clients. SYNTAX: dyndns list EXAMPLE: =>dyndns list WAN : [INIT] user = password = addr = 0.0.0.0 => RELATED COMMANDS: dyndns add Add a dynamic DNS client. dyndns delete Delete a dynamic DNS client. E-DOC-CTC-20061027-0003 v2.
PAGE 254
DynDNS Commands dyndns modify Modify a dynamic DNS client. SYNTAX: dyndns modify name = [intf = ] [user = ] [password = ] [group = ] [mx = ] [backmx = <{disabled | enabled}>] [wildcard = <{disabled | enabled}>] [offline = <{disabled | enabled}>] [service = <{dyndns | statdns | custom | No-IP | DtDNS | gnudip}>] [status = <{disabled | enabled}>] [trace = <{disabled | enabled}>] where: name The name of the dynamic DNS client to be modified.
PAGE 255
DynDNS Commands status Enable or disable the dynamic DNS client. The default is disabled. OPTIONAL trace Enable or disable the verbose console logging for the dynamic DNS client. The default is disabled. OPTIONAL EXAMPLE: =>dyndns list WAN : [INIT] user = password = addr = 0.0.0.0 =>dyndns modify name=WAN intf=RtPPPoE user=DNSuser password=_DEV_BA8C0C963BD84130 service=gnu dip =>dyndns list WAN : RtPPPoE_ppp [INIT] options = gnudip user = my_DNS_user password = ******** addr = 0.0.0.
PAGE 256
DynDNS Commands dyndns host add Add a fully qualified host name. SYNTAX: dyndns host add group = name = where: group The dynamic DNS host group. Note name A maximum of 4 different groups can be created. The name of an IP host to add. Note REQUIRED REQUIRED A maximum of 20 hosts can be configured. EXAMPLE: =>dyndns host add group=local name=localhost.com =>dyndns host list local : [ ] localhost.
PAGE 257
DynDNS Commands dyndns host delete Delete a host name. SYNTAX: dyndns host delete name = where: name The name of the IP host to be deleted. REQUIRED EXAMPLE: =>dyndns host list local : [ ] localhost.com public : [ ] publichost.com legend : [ ] not initialised [o] update in progress [v] update successful [x] error =>dyndns host delete name=publichost.com =>dyndns host list local : [ ] localhost.
PAGE 258
DynDNS Commands dyndns host flush Delete all hosts. i The hosts cannot be flushed, if there is still a group referenced to the hosts. SYNTAX: dyndns host flush 236 E-DOC-CTC-20061027-0003 v2.
PAGE 259
DynDNS Commands dyndns host list List all host names. SYNTAX: dyndns host list EXAMPLE: =>dyndns host list local : [ ] localhost.com public : [ ] publichost.com legend : [ ] not initialised [v] update successful => [o] [x] update in progress error RELATED COMMANDS: dyndns host add Add a fully qualified host name. dyndns host delete Delete a host name. E-DOC-CTC-20061027-0003 v2.
PAGE 260
DynDNS Commands dyndns service list List all dynamic DNS services. SYNTAX: dyndns service list EXAMPLE: =>dyndns service list dyndns : server = port = request = update interval = retry interval = max retry = members.dyndns.org 80 /nic/update 2097120 30 3 statdns : server port request update interval retry interval max retry = = = = = = members.dyndns.org 80 /nic/update 0 30 3 custom : server port request update interval retry interval max retry = = = = = = members.dyndns.
PAGE 261
DynDNS Commands RELATED COMMANDS: dyndns service modify E-DOC-CTC-20061027-0003 v2.0 Modify specific dynamic DNS service settings.
PAGE 262
DynDNS Commands dyndns service modify Modify specific dynamic DNS service settings. SYNTAX: dyndns service modify name = [server = ] [port = <{supported TCP/UDP port name} or number>] [request = ] [updateinterval = ] [retryinterval = ] where: name > > > > > > dyndns statdns custom No-IP DtDNS gnudip. server The hostname of the dynamic DNS server. OPTIONAL port The port of the dynamic DNS server.
PAGE 263
DynDNS Commands EXAMPLE: =>dyndns service modify name=custom server=mydyndns.org port=www-http request=hereiam | updateinterval=2000000 retryinterval=15 max_retry=5 =>dyndns service list dyndns : server = members.dyndns.org port = 80 request = /nic/update update interval = 2097120 retry interval = 30 max retry = 3 statdns : server port request update interval retry interval max retry = = = = = = members.dyndns.
PAGE 264
DynDNS Commands 242 E-DOC-CTC-20061027-0003 v2.
PAGE 265
Env Commands 13 Env Commands Introduction This chapter describes the commands of the env command group. Contents This chapter covers the following commands: env flush Flush all the non-system environment variables. 244 env get Get the current value of an environment variable. 245 env list Show all the currently available environment variables. 246 env set Set an environment variable. 247 env unset Delete a environment variable. 248 E-DOC-CTC-20061027-0003 v2.
PAGE 266
Env Commands env flush Flush all the non-system environment variables. SYNTAX: env flush 244 E-DOC-CTC-20061027-0003 v2.
PAGE 267
Env Commands env get Get the current value of an environment variable. SYNTAX: env get var = where: var The name of the environment variable. Tip REQUIRED Use the command :env list to obtain a list of all environment variables. RELATED COMMANDS: env list E-DOC-CTC-20061027-0003 v2.0 List all current environment variables.
PAGE 268
Env Commands env list Show all the currently available environment variables. SYNTAX: env list RELATED COMMANDS: env get 246 Get the current value of an environment variable. E-DOC-CTC-20061027-0003 v2.
PAGE 269
Env Commands env set Set an environment variable. SYNTAX: env set var = value = where: var The name of the environment variable. Tip REQUIRED When creating an environment variable, any name is allowed. However spaces are NOT allowed and the name may NOT start with: > > > > value “CONF” “HOST” an underscore “_” the dollar sign “$”. A quoted translated string which defines the value of the environment variable.
PAGE 270
Env Commands env unset Delete a environment variable. SYNTAX: env unset var = where: var The name of the environment variable to be deleted. Note REQUIRED System variables (built-in variables with names starting with an underscore “_”, “CONF” or “HOST”) cannot be unset, changed or deleted. EXAMPLE: =>env list _COMPANY_NAME=THOMSON multimedia _COMPANY_URL=http://www.speedtouch.com _PROD_NAME=SpeedTouch .....
PAGE 271
Eth Commands 14 Eth Commands Introduction This chapter describes the commands of the eth command group. Contents This chapter covers the following commands: eth ifadd Create a new ETH interface. 252 eth ifattach Attach an ETH interface. 253 eth ifconfig Modify an ETH interface. 254 eth ifdelete Delete an ETH interface. 255 eth ifdetach Detach an ETH interface. 256 eth iflist Display the ETH interfaces. 257 eth flush Flush all the ETH interfaces.
PAGE 272
Eth Commands 250 eth bridge igmpsnooping ifconfig Configure the bridge interface‘s IGMP snooping flags and mode 282 eth bridge igmpsnooping iflist Display a bridge interface‘s IGMP status 283 eth bridge igmpsnooping clear Clear the snooping statistics 284 eth bridge macadd Add a static MAC address to a bridge interface. 285 eth bridge macdelete Remove a MAC address from the filtering database. 287 eth bridge maclist Display the MAC address database.
PAGE 273
Eth Commands eth vlan flush Flush all VLANs. 325 eth vlan list Display all VLANs. 326 E-DOC-CTC-20061027-0003 v2.
PAGE 274
Eth Commands eth ifadd Create a new ETH interface. SYNTAX: eth ifadd intf = where: intf The name of the new ETH interface. REQUIRED RELATED COMMANDS: 252 eth ifdelete Delete an ETH interface. eth iflist Display the ETH interfaces. E-DOC-CTC-20061027-0003 v2.
PAGE 275
Eth Commands eth ifattach Attach an ETH interface. SYNTAX: eth ifattach intf = where: intf The name of the ETH interface to be attached. REQUIRED RELATED COMMANDS: eth ifdetach E-DOC-CTC-20061027-0003 v2.0 Detach an ETH interface.
PAGE 276
Eth Commands eth ifconfig Modify an ETH interface. SYNTAX: eth ifconfig intf = [dest = ] [retry = ] [vlan = ] where: 254 intf The name of the ETH interface to be configured. REQUIRED dest The destination interface for this ETH interface. OPTIONAL retry A number between 0 and 65535. Represents the number of times the ETH connection setup should retry before giving up. The default is 10.
PAGE 277
Eth Commands eth ifdelete Delete an ETH interface. SYNTAX: eth ifdelete intf = where: intf The name of the ETH interface name to be deleted. REQUIRED RELATED COMMANDS: eth ifadd Create a new ETH interface. eth iflist Display the ETH interfaces. E-DOC-CTC-20061027-0003 v2.
PAGE 278
Eth Commands eth ifdetach Detach an ETH interface. SYNTAX: eth ifdetach intf = where: intf The name of the ETH interface to be detached. REQUIRED RELATED COMMANDS: eth ifattach 256 Attach an ETH interface. E-DOC-CTC-20061027-0003 v2.
PAGE 279
Eth Commands eth iflist Display the ETH interfaces. SYNTAX: eth iflist [intf = ] [string = ] [beginstring = ] where: intf The name of the ETH interface to be displayed. Note OPTIONAL If not specified, all the ETH interfaces will be displayed. string String matching condition OPTIONAL beginstring Beginstring matching condition OPTIONAL RELATED COMMANDS: eth ifadd Create a new ETH interface. eth ifdelete Delete an ETH interface. E-DOC-CTC-20061027-0003 v2.
PAGE 280
Eth Commands eth flush Flush all the ETH interfaces. i The flush command does not impact previously saved configurations. SYNTAX: eth flush 258 E-DOC-CTC-20061027-0003 v2.
PAGE 281
Eth Commands eth bridge clear Clear the bridge statistics. SYNTAX: eth bridge clear E-DOC-CTC-20061027-0003 v2.
PAGE 282
Eth Commands eth bridge list Display the current bridge instances Syntax eth bridge list [brname = <{bridge}>] [string = ] [beginstring = ] where 260 brname The name of a bridge instance OPTIONAL string String matching condition OPTIONAL beginstring Beginstring matching condition OPTIONAL E-DOC-CTC-20061027-0003 v2.
PAGE 283
Eth Commands eth bridge add Add a new bridge instance Syntax eth bridge add brname= where brname E-DOC-CTC-20061027-0003 v2.
PAGE 284
Eth Commands eth bridge delete Delete a bridge instance Syntax eth bridge delete brname = <{bridge}> where brname 262 The name of the bridge instance to be deleted REQUIRED E-DOC-CTC-20061027-0003 v2.
PAGE 285
Eth Commands eth bridge select Select the default bridge to configure interfaces (when not setting a bridge name, for legacy purposes). Syntax eth bridge select brname = <{bridge}> where brname E-DOC-CTC-20061027-0003 v2.
PAGE 286
Eth Commands eth bridge config Modify/display the bridge configuration settings. SYNTAX: eth bridge config [brname = <{bridge}>] [age = ] [filter = <{no_WAN_broadcast | none}>] [vlan = <{disabled | enabled}>] [precedencemap = ] where: brname The name of a bridge instance age A number between 10 and 100000 (seconds). Represents the lifetime of a dynamically learned Medium Access Control (MAC) address. The default is 300.
PAGE 287
Eth Commands eth bridge dynvlan actlist Display the active MAC entries for the dynamic VLAN membership. SYNTAX: eth bridge dynvlan actlist RELATED COMMANDS: eth bridge dynvlan add Add a dynamic VLAN membership entry. eth bridge dynvlan config Modify the dynamic VLAN membership configuration. eth bridge dynvlan delete Delete a dynamic VLAN membership entry. eth bridge dynvlan list Display a dynamic VLAN membership entry. E-DOC-CTC-20061027-0003 v2.
PAGE 288
Eth Commands eth bridge dynvlan add Add a dynamic VLAN membership entry. SYNTAX: eth bridge dynvlan add [id = ] hwaddr = vlan = [remvlan = <{default}>] where: id A number between 0 and 100000. Represents the id of the dynamic VLAN membership entry. OPTIONAL hwaddr The (masked) ethernet MAC address of the dynamic VLAN membership entry. REQUIRED vlan The VLAN for the dynamic VLAN membership entry.
PAGE 289
Eth Commands eth bridge dynvlan config Modify the dynamic VLAN membership configuration. SYNTAX: eth bridge dynvlan config [timeout = ] where: timeout A number between 0 and 100000 (seconds). Represents timeout for the dynamic entries. OPTIONAL RELATED COMMANDS: eth bridge dynvlan actlist Display the active MAC entries for the dynamic VLAN membership. eth bridge dynvlan add Add a dynamic VLAN membership entry. eth bridge dynvlan delete Delete a dynamic VLAN membership entry.
PAGE 290
Eth Commands eth bridge dynvlan delete Delete a dynamic VLAN membership entry. SYNTAX: eth bridge dynvlan delete id = where: id A number between 0 and 100000. Represents the id of a dynamic VLAN membership. REQUIRED RELATED COMMANDS: 268 eth bridge dynvlan actlist Display the active MAC entries for the dynamic VLAN membership. eth bridge dynvlan add Add a dynamic VLAN membership entry. eth bridge dynvlan config Modify the dynamic VLAN membership configuration.
PAGE 291
Eth Commands eth bridge dynvlan flush Flush all dynamic VLAN membership entries. SYNTAX: eth bridge dynvlan flush E-DOC-CTC-20061027-0003 v2.
PAGE 292
Eth Commands eth bridge dynvlan list Display a dynamic VLAN membership entry. SYNTAX: eth bridge dynvlan list RELATED COMMANDS: 270 eth bridge dynvlan actlist Display the active MAC entries for the dynamic VLAN membership. eth bridge dynvlan add Add a dynamic VLAN membership entry. eth bridge dynvlan config Modify the dynamic VLAN membership configuration. eth bridge dynvlan delete Delete a dynamic VLAN membership entry. E-DOC-CTC-20061027-0003 v2.
PAGE 293
Eth Commands eth bridge flush Flush bridge interfaces and parameters. i The flush command does not impact previously saved configurations. SYNTAX: eth bridge flush E-DOC-CTC-20061027-0003 v2.
PAGE 294
Eth Commands eth bridge ifadd Add a new bridge interface. SYNTAX: eth bridge ifadd [brname = <{bridge}>] intf = where: brname The name of a bridge instance. OPTIONAL intf The name of the new bridge interface. REQUIRED RELATED COMMANDS: 272 eth bridge ifdelete Delete a bridge interface. eth bridge iflist Display the current bridge interfaces. E-DOC-CTC-20061027-0003 v2.
PAGE 295
Eth Commands eth bridge ifattach Attach a bridge interface. SYNTAX: eth bridge ifattach [brname = <{bridge}>] intf = where: brname The name of a bridge instance. OPTIONAL intf The name of the bridge interface to be attached. REQUIRED RELATED COMMANDS: eth bridge ifdetach E-DOC-CTC-20061027-0003 v2.0 Detach a bridge interface.
PAGE 296
Eth Commands eth bridge ifconfig Modify a bridge interface configuration.
PAGE 297
Eth Commands ipprec The IP precedence for this interface. Choose between: > > > OPTIONAL disabled precedence dscp. The default is disabled. priority A number between 0 and 7. Represents the default priority for tagging egress packets. The default is 0. OPTIONAL regenprio The priority regeneration table for tagged ingress packets. The default is 01234567. OPTIONAL ingressfiltering Enable/disable discard of tagged ingress packets if the interface is not part of the VLAN. The default is disabled.
PAGE 298
Eth Commands eth bridge ifdelete Delete a bridge interface. SYNTAX: eth bridge ifdelete [brname = <{bridge}>] intf = where: brname The name of a bridge instance. OPTIONAL intf The name of the bridge interface name to be deleted. REQUIRED RELATED COMMANDS: 276 eth bridge ifadd Add a new bridge interface. eth bridge iflist Display the current bridge interfaces. E-DOC-CTC-20061027-0003 v2.
PAGE 299
Eth Commands eth bridge ifdetach Detach a bridge interface. SYNTAX: eth bridge ifdetach [brname = <{bridge}>] intf = where: brname The name of a bridge instance. OPTIONAL intf The name of the bridge interface to be detached. REQUIRED RELATED COMMANDS: eth bridge ifattach E-DOC-CTC-20061027-0003 v2.0 Attach a bridge interface.
PAGE 300
Eth Commands eth bridge iflist Display the current bridge interfaces. SYNTAX: eth bridge iflist [brname = <{bridge}>] [intf = ] [string = ] [beginstring = ] where: brname The name of a bridge instance. OPTIONAL intf The name of the bridge interface to be displayed. OPTIONAL Note If not specified, all bridge interfaces are shown.
PAGE 301
Eth Commands eth bridge ifflush Flush the bridge interfaces: detach/delete all interfaces. SYNTAX: eth bridge ifflush [brname = <{bridge}>] where: brname E-DOC-CTC-20061027-0003 v2.0 The name of a bridge instance.
PAGE 302
Eth Commands eth bridge igmpsnooping config Configure the bridge instance‘s IGMP Snooping flags Syntax eth bridge igmpsnooping config [brname = <{bridge}>] [state = <{enabled|disabled}>] [floodrp = <{disabled|enabled}>] [floodmcast = <{disabled|enabled}>] where: 280 brname The name of a bridge instance OPTIONAL state Enable/Disable the IGMP Snooping The default is enabled OPTIONAL floodrp Enable/Disable flooding reports to all ports The default is disabled OPTIONAL floodmcast Enable/Disable
PAGE 303
Eth Commands eth bridge igmpsnooping list Display a bridge instance‘s snooped groups. Syntax eth bridge igmpsnooping list [brname = <{bridge}>] where: brname E-DOC-CTC-20061027-0003 v2.
PAGE 304
Eth Commands eth bridge igmpsnooping ifconfig Configure the bridge interface‘s IGMP snooping flags and mode.
PAGE 305
Eth Commands eth bridge igmpsnooping iflist Display a bridge interface‘s IGMP status Syntax Display bridge interface IGMP status [brname = <{bridge}>] [intf = <{interface}>] where: brname The name of a bridge instance OPTIONAL intf The name of the bridge interface OPTIONAL E-DOC-CTC-20061027-0003 v2.
PAGE 306
Eth Commands eth bridge igmpsnooping clear Clear the snooping statistics. Syntax eth bridge igmpsnooping clear [brname = <{bridge}>] [intf = <{interface}>] where: 284 brname The name of a bridge instance OPTIONAL intf The name of the bridge interface OPTIONAL E-DOC-CTC-20061027-0003 v2.
PAGE 307
Eth Commands eth bridge macadd Add a static MAC address to a bridge interface. This command allows to manually add static MAC addresses, which should normally be dynamically discovered by the bridge itself. SYNTAX: eth bridge macadd [brname = <{bridge}>] intf = hwaddr = [vlan = ] where: brname The name of a bridge instance. OPTIONAL intf The name of the bridge interface to which the MAC address must be added.
PAGE 308
Eth Commands EXAMPLE: =>eth bridge maclist 00:10:a4:ad:32:cf -- dynamic, ethport1, 300 seconds 00:90:d0:8b:fc:2c -- permanent 01:00:5e:00:00:67 -- static 01:00:5e:7f:ff:fa -- static 01:80:c2:00:00:00 -- permanent 01:80:c2:00:00:01 -- permanent 01:80:c2:00:00:02 -- permanent 01:80:c2:00:00:03 -- permanent ...
PAGE 309
Eth Commands eth bridge macdelete Remove a MAC address from the filtering database. SYNTAX: eth bridge macdelete [brname = <{bridge}>] hwaddr = [vlan = ] where: brname The name of a bridge instance. OPTIONAL hwaddr The Ethernet MAC address of the entry to be deleted. REQUIRED vlan The VLAN.
PAGE 310
Eth Commands RELATED COMMANDS: 288 eth bridge macadd Add a static MAC address to a bridge interface. eth bridge maclist Display the MAC address database. E-DOC-CTC-20061027-0003 v2.
PAGE 311
Eth Commands eth bridge maclist Display the MAC address database. SYNTAX: eth bridge maclist [brname = <{bridge}>] where: brname The name of a bridge instance.
PAGE 312
Eth Commands eth bridge mcdadd Add a multicast group to be dropped to the database. SYNTAX: eth bridge mcdadd [brname = <{bridge}>] srcintfs = dstintfs = where: brname The name of a bridge instance. OPTIONAL srcports The source bridge interfaces from which multicast packets must be dropped. REQUIRED dstports The destination bridge interfaces for which the multicast packets must be dropped.
PAGE 313
Eth Commands eth bridge mcddelete Delete a multicast group to be dropped from the database. SYNTAX: eth bridge mcddelete [brname = <{bridge}>] where: brname The name of a bridge instance. OPTIONAL RELATED COMMANDS: eth bridge mcdadd Add a multicast group to be dropped to the database. eth bridge mcdlist Display the multicast group to be dropped from the database. E-DOC-CTC-20061027-0003 v2.
PAGE 314
Eth Commands eth bridge mcdlist Display the multicast group to be dropped from the database. SYNTAX: eth bridge mcdlist RELATED COMMANDS: 292 eth bridge mcdadd Add a multicast group to be dropped to the database. eth bridge mcddelete Delete a multicast group to be dropped from the database. E-DOC-CTC-20061027-0003 v2.
PAGE 315
Eth Commands eth bridge rule add Add a new constraint to the VLAN learning system. SYNTAX: eth bridge rule add type = vlan = [vlan2 [isi = <{shared | independent}> = ] ] where: type Type of constraint. Choose between: > > REQUIRED shared independent. vlan The VLAN to which the constraint belongs. REQUIRED vlan2 The second VLAN for a shared constraint. OPTIONAL Note isi This parameter is required when type is shared. A number between 0 and 32.
PAGE 316
Eth Commands eth bridge rule delete Delete a constraint from the VLAN learning system. SYNTAX: eth bridge rule delete index = where: index Index of the constraint to be deleted. Tip REQUIRED Use the command :eth bridge rule list to obtain a list of the indexes of the constraints.
PAGE 317
Eth Commands eth bridge rule flush Flush all constraints from the VLAN learning system. SYNTAX: eth bridge rule flush E-DOC-CTC-20061027-0003 v2.
PAGE 318
Eth Commands eth bridge rule list Display all constraints from the VLAN learning system. SYNTAX: eth bridge rule list EXAMPLE: =>eth bridge rule list Index Type VLAN ----------1 independant default => Parameter --------Independent set identifier: 1 RELATED COMMANDS: 296 eth bridge rule add Add a new constraint to the VLAN learning system. eth bridge rule delete Delete a constraint from the VLAN learning system. E-DOC-CTC-20061027-0003 v2.
PAGE 319
Eth Commands eth bridge vlan ifadd Add a bridge interface to a VLAN. SYNTAX: eth bridge vlan ifadd name = intf = [untagged = <{disabled | enabled}>] where: name The VLAN name to which a bridge interface must be added. REQUIRED intf The name of the bridge interface to be added to the VLAN. REQUIRED untagged Enable or disable the interface as untagged for this VLAN. The default is disabled.
PAGE 320
Eth Commands eth bridge vlan ifconfig Modify a bridge interface from a VLAN. SYNTAX: eth bridge vlan ifconfig name = intf = untagged = <{disabled | enabled}> where: name The VLAN name for which a bridge interface must be modified. REQUIRED intf The name of the bridge interface to be modified. REQUIRED untagged Enable or disable the interface as untagged for this VLAN. REQUIRED RELATED COMMANDS: 298 eth bridge vlan ifadd Add a bridge interface to a VLAN.
PAGE 321
Eth Commands eth bridge vlan ifdelete Delete a bridge interface from a VLAN. SYNTAX: eth bridge vlan ifdelete name = intf = where: name The VLAN name for which a bridge interface must be deleted. REQUIRED intf The name of the bridge interface to be deleted. REQUIRED RELATED COMMANDS: eth bridge vlan ifadd Add a bridge interface to a VLAN. eth bridge vlan ifconfig Modify a bridge interface from a VLAN. eth bridge vlan iflist Display all VLANs. E-DOC-CTC-20061027-0003 v2.
PAGE 322
Eth Commands eth bridge vlan iflist Display all VLANs. SYNTAX: eth bridge vlan iflist RELATED COMMANDS: 300 eth bridge vlan ifadd Add a bridge interface to a VLAN. eth bridge vlan ifconfig Modify a bridge interface from a VLAN. eth bridge vlan ifdelete Delete a bridge interface from a VLAN. E-DOC-CTC-20061027-0003 v2.
PAGE 323
Eth Commands eth device ifconfig Configure an Ethernet interface. SYNTAX: eth device ifconfig intf = [type = <{auto | 10BaseTHD | 10BaseTFD | 100BaseTHD| 100BaseTFD} or number>] [state = <{enabled | disabled}>] where: intf The name of a physical interface. REQUIRED type The Ethernet type. Select either: OPTIONAL > auto: Auto negotiation of Ethernet communication speed (10Mb/s or 100Mb/s) and Duplex mode (half duplex or full duplex).
PAGE 324
Eth Commands EXAMPLE: =>eth device iflist Interface Type Result State ethif1 auto 100BaseTFD UP [forwarding] ethif2 auto 100BaseTFD UP [forwarding] ethif3 auto 100BaseTFD UP [forwarding] ethif4 auto 100BaseTFD UP [forwarding] usbif1 UP [forwarding] =>eth device ifconfig intf=ethif4 state=disabled =>eth device iflist Interface Type Result State ethif1 auto 100BaseTFD UP [forwarding] ethif2 auto 100BaseTFD UP [forwarding] ethif3 auto 100BaseTFD UP [forwarding] ethif4 auto 100BaseTFD DOWN [disabled] usbif1 UP
PAGE 325
Eth Commands eth device iflist Show status of Ethernet interfaces.
PAGE 326
Eth Commands eth switch group flush Set all the ports to the default settings. All the ports are placed in group 0. SYNTAX: eth switch group flush EXAMPLE: =>eth Group Group Group =>eth =>eth Group => switch group 0 Ports: 4 1 Ports: 1 2 Ports: 2 3 switch group switch group 0 Ports: 1 2 list flush list 3 4 RELATED COMMANDS: eth switch group list List all the configured switch groups. eth switch group move Move a specified port to a specified switch group. 304 E-DOC-CTC-20061027-0003 v2.
PAGE 327
Eth Commands eth switch group list List all the configured switch groups. SYNTAX: eth switch group list EXAMPLE: =>eth Group Group Group => switch group list 0 Ports: 4 1 Ports: 1 2 Ports: 2 3 RELATED COMMANDS: eth switch group flush Set all the ports to the default settings. eth switch group move Move a specified port to a specified switch group. E-DOC-CTC-20061027-0003 v2.
PAGE 328
Eth Commands eth switch group move Move a specified port to a specified switch group. SYNTAX: eth switch group move group = port = where: group A number between 0 and 4. Represents the group ID to which the port must be moved. REQUIRED port A number between 01 and 4. Represents the port to be moved.
PAGE 329
Eth Commands eth switch mirror capture Define the specified port to be the Mirror Capture Port. i Only one port can be the Mirror Capture Port at any one time. SYNTAX: eth switch mirror capture port = where: port The port to be the Mirror Capture Port. Note REQUIRED If no port number is specified, then the port number of the Mirror Capture Port is shown.
PAGE 330
Eth Commands eth switch mirror egress Enable or disable the specified port to be the Mirror Egress Port. Only one port can be the Mirror Egress Port at any one time. But a port can be the Mirror Egress Port and the Mirror Ingress Port at the same time. i SYNTAX: eth switch mirror egress port = [state = <{enabled | disabled}>] where: port The port to be the Mirror Egress Port.
PAGE 331
Eth Commands eth switch mirror ingress Enable or disable the specified port to be the Mirror Ingress Port. Only one port can be the Mirror Ingress Port at any one time. But a port can be the Mirror Egress Port and the Mirror Ingress Port at the same time. i SYNTAX: eth switch mirror ingress port = [state = <{enabled | disabled}>] where: port The port to be the Mirror Ingress Port.
PAGE 332
Eth Commands eth switch share add Add a port to be shared. SYNTAX: eth switch share add port = shared = where: port A number between 1 and 4. Represents the port. REQUIRED shared A number between 1 and 4. Represents the shared port. REQUIRED RELATED COMMANDS: 310 eth switch share delete Delete a shared port. eth switch share list Display shared ports. E-DOC-CTC-20061027-0003 v2.
PAGE 333
Eth Commands eth switch share delete Delete a shared port. SYNTAX: eth switch share delete port = shared = where: port A number between 1 and 4. Represents the port. REQUIRED shared A number between 1 and 4. Represents the shared port. REQUIRED RELATED COMMANDS: eth switch share add Add a port to be shared. eth switch share list Display shared ports. E-DOC-CTC-20061027-0003 v2.
PAGE 334
Eth Commands eth switch share list Display shared ports. SYNTAX: eth switch share list RELATED COMMANDS: 312 eth switch share add Add a port to be shared. eth switch share delete Delete a shared port. E-DOC-CTC-20061027-0003 v2.
PAGE 335
Eth Commands eth switch info Display switch capabilities. SYNTAX: eth switch info RELATED COMMANDS: Not applicable E-DOC-CTC-20061027-0003 v2.
PAGE 336
Eth Commands eth switch qos config Configure common qos parameters. SYNTAX: eth switch qos config state = [nbrOfQueues = ] [realtime = ] where: state Enable or disable QoS REQUIRED nbrOfQueues Number of QoS queues OPTIONAL realtime Enable or disable real time OPTIONAL RELATED COMMANDS: 314 eth switch qos ifconfig Configure per port QoS parameters. eth switch qos list Display QoS configuration.
PAGE 337
Eth Commands eth switch qos ifconfig Configure per port QoS parameters. SYNTAX: eth switch qos ifconfig port = mode = <802.1p|diffserv|high|none|tos> [flowcontrol = ] where: Port Port to be configured REQUIRED Mode QoS Classifier for the port REQUIRED Fowcontrol Enable or disable flow control OPTIONAL RELATED COMMANDS: eth switch qos config Configure common qos parameters. eth switch qos list Display QoS configuration.
PAGE 338
Eth Commands eth switch qos list Display QoS configuration. SYNTAX: eth switch qos list RELATED COMMANDS: 316 eth switch qos config Configure common qos parameters. eth switch qos ifconfig Configure per port QoS parameters. eth switch qos weights Configure the queue weights. E-DOC-CTC-20061027-0003 v2.
PAGE 339
Eth Commands eth switch qos weights Configure the queue weights. SYNTAX: eth switch qos weights queue0 queue1 queue2 queue3 = = = = where: QueueX The weight of queue X in WFQ (percentage) X=1 through 4 REQUIRED RELATED COMMANDS: eth switch qos config Configure common qos parameters. eth switch qos ifconfig Configure per port QoS parameters. eth switch qos list Display QoS configuration. E-DOC-CTC-20061027-0003 v2.
PAGE 340
Eth Commands eth switch shaper config Configure common ingress shaper parameters. SYNTAX: eth switch shaper config shaper = [unicast = ] [multicast = ] [broadcast = ] [control = ] [unknown = ] [discard = ] where: shaper The shaper instance REQUIRED unicast Shape unicast traffic. OPTIONAL multicast Shape multicast traffic. OPTIONAL broadcast Shape broadcast traffic.
PAGE 341
Eth Commands eth switch shaper ifconfig Configure per port shaper parameters. SYNTAX: eth switch shaper ifconfig port = ingress = shaper = [state = ] [speed = ] [burstsize = ] where: port Port number REQUIRED ingress Enabled: port is ingress port Disabled: port is egress port REQUIRED shaper Shaper instance REQUIRED state Enable/disable shaping OPTIONAL speed Speed in bits/sec.
PAGE 342
Eth Commands eth switch shaper iflist Display shaper configuration per port. SYNTAX: eth switch shaper iflist RELATED COMMANDS: 320 eth switch shaper config Configure common ingress shaper parameters. eth switch shaper ifconfig Configure per port shaper parameters. E-DOC-CTC-20061027-0003 v2.
PAGE 343
Eth Commands eth switch storm ifconfig Configure per port storm control parameters.
PAGE 344
Eth Commands eth switch storm iflist Display storm control configuration per port. SYNTAX: eth switch storm iflist RELATED COMMANDS: eth switch storm ifconfig 322 Configure per port storm control parameters. E-DOC-CTC-20061027-0003 v2.
PAGE 345
Eth Commands eth vlan add Add a new VLAN. SYNTAX: eth vlan add name = vid = [addrule = <{disabled | enabled}>] where: name The new VLAN name. REQUIRED vid A number representing the new VLAN ID. REQUIRED Note addrule The ID 1 is reserved for the default VLAN. Add (enabled) the default bridge constraint or not (disabled). The default is enabled.
PAGE 346
Eth Commands eth vlan delete Delete a VLAN. SYNTAX: eth vlan delete name = where: name The name of the VLAN to be deleted. REQUIRED EXAMPLE: =>eth vlan list Vid Name -----1 default 2 myVLAN =>eth vlan delete name=myVLAN vid=2 =>eth vlan list Vid Name -----1 default => RELATED COMMANDS: 324 eth vlan add Add a new VLAN. eth vlan list Display all VLANs. E-DOC-CTC-20061027-0003 v2.
PAGE 347
Eth Commands eth vlan flush Flush all VLANs. i All the VLANs, except the default VLAN will be flushed. SYNTAX: eth vlan flush EXAMPLE: =>eth vlan list Vid Name -----1 default 2 myVLAN 3 yourVLAN =>eth vlan flush =>eth vlan list Vid Name -----1 default => E-DOC-CTC-20061027-0003 v2.
PAGE 348
Eth Commands eth vlan list Display all VLANs. SYNTAX: eth vlan list EXAMPLE: =>eth vlan list Vid Name -----1 default 2 myVLAN => RELATED COMMANDS: 326 eth vlan add Add a new VLAN. eth vlan delete Delete a VLAN. E-DOC-CTC-20061027-0003 v2.
PAGE 349
Expr Commands 15 Expr Commands Introduction This chapter describes the commands of the expr command group. Contents This chapter covers the following commands: expr add Add a subexpression to an expression. 328 expr delete Delete an expression. 332 expr flush Flush all the expressions. 334 expr list List the expressions. 335 expr modify Modify an expression. 339 E-DOC-CTC-20061027-0003 v2.
PAGE 350
Expr Commands expr add Add a subexpression to an expression.
PAGE 351
Expr Commands intfgroup The IP interface group. Choose between: > > > > > > wan local lan tunnel dmz guest. Note tos OPTIONAL The parameters tos, precedence and dscp are mutually exclusive. The Differentiated Services Code Point (DSCP) in the IP packet (part of tos). Select a DSCP (see “ Differentiated Services Code Point (DSCP)” on page 753) or, alternatively, specify the number. Note OPTIONAL The parameters tos, precedence and dscp are mutually exclusive.
PAGE 352
Expr Commands 330 icmpcode A number between 0 and 15. Represents the ICMP code (or beginning of range) of the packet. OPTIONAL icmpcodeend A number between 0 and 15. Represents the ICMP code range end (inclusive). OPTIONAL E-DOC-CTC-20061027-0003 v2.
PAGE 353
Expr Commands EXAMPLE: =>expr list name type use flags expression -----------------------------------------------------------------------------------------_myPPP_ppp intf 0 D 1. intf=myPPP_ppp _eth0 intf 0 D 1. intf=eth0 wan intf 0 1. intfgroup=0 lan intf 28 1. intfgroup=2 local intf 0 1. intfgroup=1 notwan intf 1 1. intfgroup=2 2. intfgroup=1 _10.0.0.138 ip 0 D 1. addr=10.0.0.138 _192.168.1.254 ip 0 D 1. addr=192.168.1.254 ... DiffServ sip serv serv 0 1 h323 serv 1 1. 1. 2. 1. 2. 3.
PAGE 354
Expr Commands expr delete Delete an expression. SYNTAX: expr delete name = [index = ] where: name The name of the expression to be deleted. REQUIRED index The index of the subexpression to be deleted. OPTIONAL Note 332 If not specified, all the subexpressions wil be deleted. E-DOC-CTC-20061027-0003 v2.
PAGE 355
Expr Commands EXAMPLE: =>expr list name type use flags expression -----------------------------------------------------------------------------------------_myPPP_ppp intf 0 D 1. intf=myPPP_ppp _eth0 intf 0 D 1. intf=eth0 wan intf 0 1. intfgroup=0 lan intf 28 1. intfgroup=2 local intf 0 1. intfgroup=1 notwan intf 1 1. intfgroup=2 2. intfgroup=1 myEXPR intf 0 1. intf=Internet intfgroup=2 _10.0.0.138 ip 0 D 1. addr=10.0.0.138 _192.168.1.254 ip 0 D 1. addr=192.168.1.254 ...
PAGE 356
Expr Commands expr flush Flush all the expressions. SYNTAX: expr flush 334 E-DOC-CTC-20061027-0003 v2.
PAGE 357
Expr Commands expr list List the expressions. SYNTAX: expr list [name = ] [type = <{intf | ip | serv}>] [format = <{pretty | cli}>] [string = ] [beginstring = ] where: name The name of an existing expression. Note type OPTIONAL intf ip serv. Note format If not specified, all the expressions will be listed. The expression type. Choose between: > > > OPTIONAL If not specified, the expressions of all types will be shown. Select the output format of the list.
PAGE 358
Expr Commands EXAMPLE 1: =>expr list name type use flags expression -----------------------------------------------------------------------------------------_Internet intf 0 D 1. intf=Internet _LocalNetwork intf 0 D 1. intf=LocalNetwork HTTPI_if_0 intf 1 D 1. intf=LocalNetwork 2. intf=LocalNetwork 3. intf=LocalNetwork HTTP_if_0 intf 1 D 1. intfgroup=2 HTTPs_if_0 intf 1 D 1. intfgroup=2 FTP_if_0 intf 1 D 1. intfgroup=2 TELNET_if_0 intf 1 D 1. intfgroup=2 DNS-S_if_0 intf 1 D 1.
PAGE 359
Expr Commands EXAMPLE 2: =>expr list format=cli :expr add name=_Internet type=intf intf=Internet :expr add name=_LocalNetwork type=intf intf=LocalNetwork :expr add name=HTTPI_if_0 type=intf intf=LocalNetwork :expr add name=HTTPI_if_0 type=intf intf=LocalNetwork :expr add name=HTTPI_if_0 type=intf intf=LocalNetwork :expr add name=HTTP_if_0 type=intf intfgroup=lan :expr add name=HTTPs_if_0 type=intf intfgroup=lan :expr add name=FTP_if_0 type=intf intfgroup=lan :expr add name=TELNET_if_0 type=intf intfgroup=l
PAGE 360
Expr Commands RELATED COMMANDS: 338 expr add Add a subexpression to an expression. expr delete Delete an expression. E-DOC-CTC-20061027-0003 v2.
PAGE 361
Expr Commands expr modify Modify an expression.
PAGE 362
Expr Commands intfgroup The IP interface group. Choose between: > > > > > > wan local lan tunnel dmz guest. Note bridgeport OPTIONAL The parameters tos, precedence and dscp are mutually exclusive. OPTIONAL The parameters tos, precedence and dscp are mutually exclusive. The DSCP in the IP packet (part of tos). Select a DSCP (see “ Differentiated Services Code Point (DSCP)” on page 753). Note 340 Only for expression type intf. The precedence in the IP packet (part of tos).
PAGE 363
Expr Commands icmpcode A number between 0 and 15. Represents the ICMP code (or beginning of range) of the packet. OPTIONAL icmpcodeend A number between 0 and 15. Represents the ICMP code range end (inclusive). OPTIONAL E-DOC-CTC-20061027-0003 v2.
PAGE 364
Expr Commands 342 E-DOC-CTC-20061027-0003 v2.
PAGE 365
Firewall Commands 16 Firewall Commands Introduction This chapter describes the commands of the firewall command group. Contents This chapter covers the following commands: firewall config Configure the firewall options. 344 firewall clear Flush the firewall configuration. 346 firewall list List the firewall configuration. 347 firewall chain add Add a chain. 349 firewall chain delete Delete a chain. 351 firewall chain flush Flush all chains. 353 firewall chain list List all chains.
PAGE 366
Firewall Commands firewall config Configure the firewall options. SYNTAX: firewall config [state = <{disabled | enabled}>] [keep = <{disabled | enabled}>] [tcpchecks = <{none | fast | exact}>] [udpchecks = <{disabled|enabled}>] [icmpchecks = <{disabled | enabled}>] [logdefault = <{disabled | enabled}>] [logthreshold = <{disabled | enabled}>] [tcpwindow = ] where: state Enable or disable the firewall. The default is enabled.
PAGE 367
Firewall Commands logdefault Disable or enable logging of default firewall rule. The default is disabled. OPTIONAL logthreshold Disable or enable log thresholding. The default is enabled. OPTIONAL tcpwindow A number between 0 and 1073725440. This parameter permits to modify the TCP window for fast TCP checks. The default is 65536.
PAGE 368
Firewall Commands firewall clear Flush the firewall configuration. SYNTAX: firewall clear 346 E-DOC-CTC-20061027-0003 v2.
PAGE 369
Firewall Commands firewall list List the firewall configuration. SYNTAX: firewall list [format = <{pretty | cli}>] where: format Select the output format in which the configuration must be shown. Choose between: > pretty: the configuration is shown as intuitive output in clear text. > cli: the configuration is shown via the CLI commands configuration. OPTIONAL The default is pretty. E-DOC-CTC-20061027-0003 v2.
PAGE 370
Firewall Commands EXAMPLE of output in text mode: =>firewall list Config ====== State Keep TcpChecks TcpWindow IcmpChecks LogDefault LogThreshold : : : : : : : Modules ======= Module State enabled disabled exact 65536 enabled disabled enabled Text Hooks ------------------------------------------------------------------------------------------------fire enabled Firewall Administration Module sink, forward, source host_service enabled Firewall Host Service Module forward level enabled Firewall Level M
PAGE 371
Firewall Commands firewall chain add Add a chain. SYNTAX: firewall chain add chain = where: chain E-DOC-CTC-20061027-0003 v2.0 The name of the chain to be added.
PAGE 372
Firewall Commands EXAMPLE: =>firewall chain list Chains ====== Name Description ----------------------------------------------------------------sink system forward system source system sink_fire system forward_fire system source_fire system forward_host_service system forward_level system sink_system_service system forward_level_BlockAll system forward_level_Standard system forward_level_Disabled system =>firewall chain add chain=myCHAIN =>firewall chain list Chains ====== Name Description ----------------
PAGE 373
Firewall Commands firewall chain delete Delete a chain. SYNTAX: firewall chain delete chain = where: chain E-DOC-CTC-20061027-0003 v2.0 The name of the chain to be deleted.
PAGE 374
Firewall Commands EXAMPLE: =>firewall chain list Chains ====== Name Description ----------------------------------------------------------------sink system forward system source system sink_fire system forward_fire system source_fire system forward_host_service system forward_level system sink_system_service system forward_level_BlockAll system forward_level_Standard system forward_level_Disabled system myCHAIN user =>firewall chain delete chain=myCHAIN =>firewall chain list Chains ====== Name Description
PAGE 375
Firewall Commands firewall chain flush Flush all chains. SYNTAX: firewall chain flush E-DOC-CTC-20061027-0003 v2.
PAGE 376
Firewall Commands firewall chain list List all chains. SYNTAX: firewall chain list [format = <{pretty | cli}>] where: format Select the output format in which the chains must be shown. Choose between: > pretty: the chains are shown as intuitive output in clear text. > cli: the chains are shown via the CLI commands configuration. OPTIONAL The default is pretty.
PAGE 377
Firewall Commands firewall debug clear Clear the firewall statistics.
PAGE 378
Firewall Commands firewall debug stats Display the firewall statistics.
PAGE 379
Firewall Commands firewall debug traceconfig Configure the firewall trace options. SYNTAX: firewall debug traceconfig [tcpchecks = <{disabled | enabled}>] [udpchecks = <{disabled|enabled}>] [icmpchecks = <{disabled | enabled}>] [sink = <{none | all | accept | deny | drop | reset} or number>] [forward = <{none | all | accept | deny | drop reset} or number>] [source = <{none | all | accept | deny | drop | reset} or number>] where: tcpchecks Disable or enable tcpchecks traces. The default is disabled.
PAGE 380
Firewall Commands firewall level add Add a security level. SYNTAX: firewall level add name = [index = ] [readonly = <{disabled | enabled}>] [udptrackmode = <{strict | loose}>] [service = <{disabled | enabled}>] [proxy = <{disabled|enabled}>] [text = ] where: name The name of the security level to be added. REQUIRED index The index of the security level. OPTIONAL Use the command :firewall level list to obtain a list of indexes.
PAGE 381
Firewall Commands firewall level delete Delete a security level. SYNTAX: firewall level delete name = where: name The name of the security level to be deleted. REQUIRED RELATED COMMANDS: firewall level add Add a security level. firewall level list List all the security levels. E-DOC-CTC-20061027-0003 v2.
PAGE 382
Firewall Commands firewall level flush Flush the security level configuration. SYNTAX: firewall level flush 360 E-DOC-CTC-20061027-0003 v2.
PAGE 383
Firewall Commands firewall level list List all the security levels. SYNTAX: firewall level list [format = <{pretty | cli}>] [string = ] [beginstring = ] where: format Select the output format in which the security levels must be shown. Choose between: > pretty: the security levels are shown as intuitive output in clear text. > cli: the security levels are shown via the CLI commands configuration. OPTIONAL The default is pretty.
PAGE 384
Firewall Commands firewall level modify Configure a security level. SYNTAX: firewall level modify name = [index = ] [readonly = <{disabled | enabled}>] [udptrackmode = <{strict | loose}>] [service = <{disabled | enabled}>] [proxy = <{disabled|enabled}>] [text = ] where: name The name of the security level to be added. REQUIRED index The index of the security level. OPTIONAL Use the command :firewall level list to obtain a list of indexes.
PAGE 385
Firewall Commands firewall level set Set the security level or display the current security level. SYNTAX: firewall level set [name = ] where: name The name of the security level to be set. Note E-DOC-CTC-20061027-0003 v2.0 OPTIONAL If no security level is specified, the current security level will be shown.
PAGE 386
Firewall Commands firewall rule add Add a firewall rule. SYNTAX: firewall rule add i chain = [index = ] [name = ] [clink = ] [srcintf [!]= ] [srcip [!]= ] [dstip [!]= ] [serv [!]= ] [log = <{disabled | enabled}>] [state = <{disabled | enabled}>] action = <{accept|deny|drop|reset|count|link}> If a value is preceded by a “!”, it means NOT. For example “srcintf=!wan” means “if the source interface is different from WAN”.
PAGE 387
Firewall Commands firewall rule delete Delete a firewall rule. SYNTAX: firewall rule delete chain = index = where: chain The name of the chain in which a rule must be deleted. REQUIRED index The number of the rule in the chain. REQUIRED RELATED COMMANDS: firewall rule add E-DOC-CTC-20061027-0003 v2.0 Add a firewall rule.
PAGE 388
Firewall Commands firewall rule flush Flush all firewall rules. SYNTAX: firewall rule flush [chain = ] where: chain The name of the chain for which the rules must be flushed. Note 366 OPTIONAL If not specified, the rules of all the chains will be flushed. E-DOC-CTC-20061027-0003 v2.
PAGE 389
Firewall Commands firewall rule list Show a list of the firewall rules in a chain. SYNTAX: firewall rule list [chain = ] [format = <{pretty | cli}>] [string = ] [beginstring = ] where: chain The name of the chain for which the rules must be listed. Note format If not specified, the rules of all the chains are shown. Select the output format in which the list must be shown. Choose between: > > OPTIONAL OPTIONAL pretty: the list is shown as intuitive output in clear text.
PAGE 390
Firewall Commands EXAMPLE: =>firewall rule list Rules (flags: C=Constant, D=Dynamic, E=Enable, L=Log) ===== Chain Nr. Flags Rule --------------------------------------------------------------------------------------sink 1 CDE : link sink_fire 2 CDE : link sink_system_service sink_fire 1 C E SSDP : accept ssdp_serv lan.* > *.ssdp_ip sink_system_service 1 CDE HTTPI : accept HTTPI_sv_0 HTTPI_if_0.* > *.* 2 DE PING_RESPONDER : accept PING_RESPONDER_sv_0 PING_RESPON DER_ if_0.* > *.
PAGE 391
Firewall Commands firewall rule modify Modify a firewall rule. SYNTAX: firewall rule modify i chain = index = [newindex = ] [name = ] [clink = ] [srcintf [!]= ] [srcip [!]= ] [dstintf [!]= ] [dstip [!]= ] [serv [!]= ] [log = <{disabled | enabled}>] [state = <{disabled | enabled}>] [action = ] If a value is preceded by a “!”, it means NOT.
PAGE 392
Firewall Commands firewall rule debug clear Clear the firewall rule statistics. SYNTAX: firewall rule debug clear [chain = ] [index = ] where: chain The name of the chain which contains the rule. OPTIONAL index The number of the rule in the chain. OPTIONAL Note 370 If not specified, the statistics for all the rules in the chain will be cleared. E-DOC-CTC-20061027-0003 v2.
PAGE 393
Firewall Commands EXAMPLE: =>firewall rule debug stats chain index packets bytes ---------------------------------------------------------------------------sink 1 0 0 2 4 192 forward 1 0 0 2 0 0 3 10 480 source 1 0 0 sink_fire 1 0 0 source_fire 1 0 0 forward_level 1 10 480 sink_system_service 1 1 48 2 0 0 ...
PAGE 394
Firewall Commands firewall rule debug stats Show the firewall rule statistics. SYNTAX: firewall rule debug stats [chain = ] [index = ] where: chain The name of the chain for which the statistics must be shown. Note index 372 If not specified, the statistics for all the chains will be shown. The number of the rule in the chain. Note OPTIONAL OPTIONAL If not specified, the statistics for all the rules in the chain are shown. E-DOC-CTC-20061027-0003 v2.
PAGE 395
Firewall Commands EXAMPLE: =>firewall rule debug stats chain index packets bytes ---------------------------------------------------------------------------sink 1 0 0 2 4 192 forward 1 0 0 2 0 0 3 10 480 source 1 0 0 sink_fire 1 0 0 source_fire 1 0 0 forward_level 1 10 480 sink_system_service 1 1 48 2 0 0 3 0 0 4 0 0 5 0 0 6 0 0 7 0 0 8 0 0 9 0 0 10 0 0 11 0 0 12 0 0 13 0 0 14 1 48 15 0 0 16 0 0 17 2 96 forward_level_BlockAll 1 0 0 forward_level_Standard 1 0 0 forward_level_Disabled 1 10 480 => RELATED CO
PAGE 396
Firewall Commands firewall rule debug traceconfig Display or modify the rule trace configuration. SYNTAX: firewall rule debug traceconfig [trace = <{disabled | enabled}>] where: trace Enable or disable rule traces. The default is disabled. OPTIONAL EXAMPLE: =>firewall rule debug traceconfig :firewall rule debug traceconfig state=disabled => 374 E-DOC-CTC-20061027-0003 v2.
PAGE 397
GRP Commands 17 GRP Commands Introduction This chapter describes the commands of the grp command group. Contents This chapter covers the following commands: grp config Set the Generic Routing Protocol (GRP) configuration settings. 376 grp flush Flush the GRP interface settings and parameters. 377 grp rtlist Show the current routes in the GRP interfaces routing table. 378 grp rip config Configure the RIP settings. 379 grp rip flush Flush the RIP interface settings and global parameters.
PAGE 398
GRP Commands grp config Set the Generic Routing Protocol (GRP) configuration settings. SYNTAX: grp config [cdistance = ] [kdistance = ] [rdistance = ] [trace = <{disabled | enabled}>] where: cdistance A number between 0 and 255. Sets the distance of the connected route type. The default is 0. OPTIONAL kdistance A number between 0 and 255. Sets the distance of the kernel route type. The default is 1. OPTIONAL rdistance A number between 0 and 255.
PAGE 399
GRP Commands grp flush Flush the GRP interface settings and parameters. SYNTAX: grp flush E-DOC-CTC-20061027-0003 v2.
PAGE 400
GRP Commands grp rtlist Show the current routes in the GRP interfaces routing table. SYNTAX: grp rtlist [dst = ] [dstmask = ] where: dst The destination IP address of the route. Supports IP/mask notation. Note dstmask OPTIONAL If no destination IP address is specified, all the current routes will be shown. The destination IP address mask, either in dotted or in numerical cidr notation.
PAGE 401
GRP Commands grp rip config Configure the RIP settings.
PAGE 402
GRP Commands 380 impsrt Enable or disable the import of static routes. The default is enabled. OPTIONAL impdefkrt Enable or disable the import of the default kernel route. The default is enabled. OPTIONAL impdefsrt Enable or disable the import of the default static route. The default is enabled. OPTIONAL exprt Enable or disable the export of received RIP routes. The default is enabled. OPTIONAL expdefrt Enable or disable the export of the received RIP default route. The default is enabled.
PAGE 403
GRP Commands EXAMPLE: =>grp rip show RIP routing protocol config dump -----------------------------------RIP daemon is enabled Global RIP queries received : 0 Global RIP route changes : 0 Default version : send rip_v2, receive rip_v2 Default redistribution metric is 1 Sending routing table updates every 30 seconds with +/-5% Route timeout after 180 seconds Route garbage collect after 120 seconds Import of connected routes is enabled Import of kernel routes is enabled Import of static routes is enabled Impo
PAGE 404
GRP Commands grp rip flush Flush the RIP interface settings and global parameters. SYNTAX: grp rip flush 382 E-DOC-CTC-20061027-0003 v2.
PAGE 405
GRP Commands grp rip ifconfig Configure a RIP interface. SYNTAX: grp rip ifconfig intf = [rip = <{disabled | enabled}>] [rxversion = <{rip_unspec | rip_v1 | rip_v2 | rip_v1-2}>] [authmode = <{none | cleartext}>] [authstring = ] [splithorizon = <{disable | enable}>] where: intf The name of the RIP interface to be configured. REQUIRED Use the command :grp iflist to obtain a list of available interfaces. Tip rip Enabled or disabled RIP on this interface.
PAGE 406
GRP Commands EXAMPLE: =>grp rip ifconfig intf = myPPP_ppp [rip] = disabled [rxversion] = rip_unspec [authmode] = none [authstr] = [passive] = disabled [splithorizon] = enabled :grp rip ifconfig intf=myPPP_ppp => 384 E-DOC-CTC-20061027-0003 v2.
PAGE 407
GRP Commands grp rip show Show the RIP settings and the routes in the RIP database.
PAGE 408
GRP Commands 386 E-DOC-CTC-20061027-0003 v2.
PAGE 409
Hostmgr Commands 18 Hostmgr Commands Introduction This chapter describes the commands of the hostmgr command group. Contents This chapter covers the following commands: hostmgr add Add host device info to the host manager. 388 hostmgr clear Remove all the hosts from the list. 390 hostmgr config Configure the host manager parameters. 391 hostmgr delete Delete the host device info from the host manager. 392 hostmgr flush Flush the host manager configuration.
PAGE 410
Hostmgr Commands hostmgr add Add host device info to the host manager. SYNTAX: hostmgr add mac_addr = [ip_addr = ] [name = ] [type = <{generic_device|desktop_computer|laptop_computer| set_top_box|pda|gaming_console|phone|mobile_phone| printer|mass_storage_device}>] [ipintf = ] [ethintf = ] [physintf = ] where: mac_addr The MAC address of the host to be added. REQUIRED ip_addr The host IP address. OPTIONAL name The host name.
PAGE 411
Hostmgr Commands EXAMPLE: =>hostmgr list MAC-address IP-address -------------------00:10:a4:ad:32:cf 192.168.1.64 Flags Type ----- ---C Generic Device Intf ---LocalNetwork Hw Intf ------ethif4 Hostname -------MyComputer =>hostmgr add mac_addr=00:10:a4:33:56:53 name=Play type=Playstation =>hostmgr list MAC-address IP-address Flags Type Intf ------------------------ ------00:10:a4:33:56:53 0.0.0.0 Playstation ethif1 00:10:a4:ad:32:cf 192.168.1.
PAGE 412
Hostmgr Commands hostmgr clear Remove all the hosts from the list. SYNTAX: hostmgr clear EXAMPLE: =>hostmgr list MAC-address ----------00:10:a4:33:56:53 00:10:a4:ad:32:cf er IP-address ---------0.0.0.0 192.168.1.64 Flags ----C Type ---Playstation Generic Device Intf ---ethif1 LocalNetwork Hw Intf ------ethif1 ethif4 Hostname -------Play MyComput =>hostmgr clear =>hostmgr list No hosts found. => RELATED COMMANDS: hostmgr delete 390 Delete the host device info from the host manager.
PAGE 413
Hostmgr Commands hostmgr config Configure the host manager parameters. SYNTAX: hostmgr config [state = <{disabled | enabled}>] [scantime = ] [autosave = <{disabled | enabled}>] [trace = <{disabled | enabled}>] where: state Enable or disable the host manager daemon. The default is enabled. OPTIONAL scantime A number between 10 an 600 (seconds). Represents the time between two scans. The default is 30 (seconds). OPTIONAL autosave Enable or disable automatic saves to flash memory.
PAGE 414
Hostmgr Commands hostmgr delete Delete the host device info from the host manager. SYNTAX: hostmgr delete mac_addr = where: mac_addr The MAC address of the host to be removed. REQUIRED EXAMPLE: =>hostmgr list MAC-address ----------00:10:a4:33:56:53 00:10:a4:ad:32:cf er IP-address ---------0.0.0.0 192.168.1.
PAGE 415
Hostmgr Commands hostmgr flush Flush the host manager configuration. The host manager configuration is cleaned and returned to default values. SYNTAX: hostmgr flush E-DOC-CTC-20061027-0003 v2.
PAGE 416
Hostmgr Commands hostmgr list List all the host devices. SYNTAX: hostmgr list EXAMPLE: =>hostmgr list MAC-address ----------00:10:a4:33:56:53 00:10:a4:ad:32:cf er IP-address ---------0.0.0.0 192.168.1.64 Flags ----C Type ---Playstation Generic Device Intf ---ethif1 LocalNetwork Hw Intf ------ethif1 ethif4 Hostname -------Play MyComput => RELATED COMMANDS: 394 hostmgr add Add host device info to the host manager. hostmgr delete Delete the host device info from the host manager.
PAGE 417
IDS Commands 19 IDS Commands Introduction This chapter describes the commands of the ids command group. Contents This chapter covers the following commands: ids clear Reset the IDS statistics. 396 ids config Display/modify the Intrusion Detection System (IDS) configuration. 397 ids parser list Display the IDS parser configuration. 398 ids parser modify Modify the IDS parser configuration. 399 ids pattern clear Reset the pattern tracker.
PAGE 418
IDS Commands ids clear Reset the IDS statistics. SYNTAX: ids clear RELATED COMMANDS: ids parser list 396 Display the IDS parser configuration. E-DOC-CTC-20061027-0003 v2.
PAGE 419
IDS Commands ids config Display/modify the Intrusion Detection System (IDS) configuration. SYNTAX: ids config [state = <{disabled | enabled}>] [trace = <{disabled|enabled}>] where: state Enable or disable IDS checks. The default is enabled. OPTIONAL trace Enable or disable tracing. The default is disabled. OPTIONAL EXAMPLE: =>ids config IDS configuration: ================= state : enabled traces ::disabled => E-DOC-CTC-20061027-0003 v2.
PAGE 420
IDS Commands ids parser list Display the IDS parser configuration. SYNTAX: ids parser list [parser = ] where: parser The name of the parser REQUIRED EXAMPLE: =>ids parser list parser state ----------------------------------------fragment enabled scan enabled dos enabled proto enabled rate enabled => 398 E-DOC-CTC-20061027-0003 v2.
PAGE 421
IDS Commands ids parser modify Modify the IDS parser configuration. SYNTAX: ids parser modify parser = state = <{disabled | enabled}> where: parser The name of the IDS parser of which the configuration must be modifi ed. REQUIRED state Disable or enable the parser. REQUIRED E-DOC-CTC-20061027-0003 v2.
PAGE 422
IDS Commands EXAMPLE: =>ids list Resources: ========== resource total maximum --------------------------------parsers 5 10 signatures 38 50 Signatures: ========== parser signature hits action state --------------------------------------------------------------------------------------fragment fragment sweep 0 log, drop enabled fragment zero-length fragment size 0 log, drop enabled fragment small fragment size 0 log, drop enabled fragment fragment size overrun 0 log, drop enabled fragment fragment overlap 0
PAGE 423
IDS Commands ids pattern clear Reset the pattern tracker.
PAGE 424
IDS Commands ids pattern list Display the patterns in the pattern tracker. SYNTAX: ids pattern list [size = <{10 | 100 | full} or number>] where: size The size of the IDS pattern list that will be shown. Choose between: > > > OPTIONAL 10 100 full or, alternatively, specify a number. The default is full. EXAMPLE: =>ids pattern list 1. # 40002# UDP period: [00001564..00001565] 2. # 30002# UDP period: [00001564..00001566] 3. # 5000a# UDP period: [00001411..00001425] => *.*.*.*:* -> *.*.*.
PAGE 425
IDS Commands ids pattern stats Display the pattern tracker statistics. SYNTAX: ids pattern stats EXAMPLE: =>ids pattern stats Pattern tracker statistics: --------------------------memory maximum number of patterns number of active patterns number of recycled patterns number of pattern searches number of new patterns maximum number of hash collisions % of hash entries with collisions % of hash entries unused => : : : : : : : : : 32768 bytes 512 8 0 9 8 1 0.09 99.
PAGE 426
IDS Commands ids signature list Displays the ids signature configuration SYNTAX ids signature list [signature =
PAGE 427
IDS Commands ids signature modify Modify the states of the signatures.
PAGE 428
IDS Commands ids threshold clear Reset the IDS thresholds to their default values. SYNTAX: ids threshold clear EXAMPLE: =>ids threshold list index name window limit scaling ----------------------------------------------------------------1. ids scan 20 20 enabled 2. ids flood 2 100 disabled 3. ids tcp rate 10 300 enabled 4. ids udp rate 1 200 disabled 5. ids icmp rate 1 200 disabled 6.
PAGE 429
IDS Commands ids threshold list Display the IDS thresholds. SYNTAX: ids threshold list EXAMPLE: =>ids threshold list index name window limit scaling ----------------------------------------------------------------1. ids scan 20 20 enabled 2. ids flood 2 100 disabled 3. ids tcp rate 1 200 disabled 4. ids udp rate 1 200 disabled 5. ids icmp rate 1 200 disabled 6. ids ip rate 1 200 disabled => RELATED COMMANDS: ids threshold clear Reset the IDS thresholds to their default values.
PAGE 430
IDS Commands ids threshold modify Modify the IDS thresholds. SYNTAX: ids threshold modify index = [window = ] [limit = ] [scaling = <{disabled | enabled}>] where: index The index of the IDS threshold to be modified. Tip REQUIRED Use the command :ids threshold list to obtain the indexes. window A number (of seconds). Represents the time window of the threshold. OPTIONAL limit A number. Represents the limit of the threshold.
PAGE 431
IGMP Commands 20 IGMP Commands Introduction This chapter describes the commands of the IGMP command group. Contents This chapter covers the following commands: igmp host config Display or modify global IGMP configuration. 410 igmp host flush Flush the IGMP settings. 411 igmp host list Show the IGMP groups. 412 igmp host debug clear Show the IGMP groups. 412 igmp host ifconfig Configure an IGMP interface. 413 igmp host iflist Show the configuration of the IGMP interfaces.
PAGE 432
IGMP Commands igmp host config Display or modify global IGMP configuration. SYNTAX: igmp host config [requirera = <{disabled | enabled}>] where: requirera Enable or disable the router alert IP option check. The default is disabled. OPTIONAL EXAMPLE: =>igmp host confighostmgr list Router alert IP option check : disabled => RELATED COMMANDS: igmp host debug clear 410 Show the IGMP groups. E-DOC-CTC-20061027-0003 v2.
PAGE 433
IGMP Commands igmp host flush Flush the IGMP settings. SYNTAX: igmp host flush E-DOC-CTC-20061027-0003 v2.
PAGE 434
IGMP Commands igmp host list Show the IGMP groups. SYNTAX: igmp host list [intf = ] [expand = <{disabled | enabled}>] where: intf The IP interface name. OPTIONAL expand Enable or disable expanded listing of IGMP groups. The default is disabled. OPTIONAL EXAMPLE: =>igmp host list Interface 4 lan1 4 lan1 => 412 Group 224.0.0.103 239.255.255.250 Filter-Mode EXCLUDE EXCLUDE Source none none E-DOC-CTC-20061027-0003 v2.
PAGE 435
IGMP Commands igmp host ifconfig Configure an IGMP interface. SYNTAX: igmp host ifconfig intf = version = <{none |IGMPv1 |IGMPv2 |IGMPv3}> where: intf The IP interface name. REQUIRED version The IGMP version of the IP interface. Choose between: REQUIRED > > > > IGMPv1 IGMPv2 IGMPv3 none EXAMPLE: =>igmp host ifconfig intf = lan1 version = IGMPv1 :igmp host ifconfig intf=lan1 version=IGMPv1 => RELATED COMMANDS: igmp proxy iflist E-DOC-CTC-20061027-0003 v2.
PAGE 436
IGMP Commands igmp host iflist Show the configuration of the IGMP interfaces. SYNTAX: igmp host iflist [expand = <{disabled | enabled}>] where: expand Enable or disable expanded listing of IGMP interfaces configuration. The default is disabled.
PAGE 437
IGMP Commands igmp host debug clear Clear IGMP statistics. SYNTAX: igmp host debug clear RELATED COMMANDS: igmp host debug stats E-DOC-CTC-20061027-0003 v2.0 Print IGMP statistics.
PAGE 438
IGMP Commands igmp host debug stats Print IGMP statistics.
PAGE 439
IGMP Commands igmp proxy config Configure the IGMP proxy. SYNTAX: igmp proxy config [state = <{disabled | enabled}>] [qi = ] [qri = ] [lmqi = ] [rv = ] [requirera = <{disabled | enabled}>] [localgroup = <{disabled | enabled}>] where: state Enable or disable the IGMP proxy. The default is enabled. OPTIONAL qi A number between 1 and 86400. Represents the interval in seconds between general queries sent by the querier.
PAGE 440
IGMP Commands EXAMPLE: =>igmp proxy config IGMP proxy state Query Interval Query Response Interval Last Member Query Interval Robustness variable Router alert IP option check Process local multicast group => : : : : : : : disabled 0 days, 0:02:05 0 days, 0:00:10 0 days, 0:00:01 2 disabled disabled RELATED COMMANDS: igmp proxy grouplist 418 Show the learned groups on an IGMP proxy interface. E-DOC-CTC-20061027-0003 v2.
PAGE 441
IGMP Commands igmp proxy flush Flush all IGMP proxy settings and learned groups. SYNTAX: igmp proxy flush E-DOC-CTC-20061027-0003 v2.
PAGE 442
IGMP Commands igmp proxy grouplist Show the learned groups on an IGMP proxy interface. SYNTAX: igmp proxy grouplist [intf = ] [expand = <{disabled | enabled}>] where: intf The name of the IGMP proxy interface to be listed. OPTIONAL expand Enable or disable expanded listing of the learned groups on an IGMP proxy interface. The default is disabled. OPTIONAL RELATED COMMANDS: igmp proxy config 420 Configure the IGMP proxy. E-DOC-CTC-20061027-0003 v2.
PAGE 443
IGMP Commands igmp proxy ifconfig Configure an IGMP proxy interface. SYNTAX: igmp proxy ifconfig intf = [state = <{inactive | downstream | upstream}>] [version = <{IGMPv1 | IGMPv2 | IGMPv3}>] [fastleave = <{disabled | enabled}>] where: intf The name of the IGMP proxy interface to be configured. REQUIRED state The state of the IGMP proxy interface. Choose between: OPTIONAL > > > version downstream upstream The IGMP version of the IGMP proxy interface.
PAGE 444
IGMP Commands igmp proxy iflist Show the configuration of an IGMP proxy interface. SYNTAX: igmp proxy iflist [expand = <{disabled | enabled}>] where: expand Enable or disable expanded listing of IGMP proxy interface configuration. The default is disabled.
PAGE 445
IGMP Commands igmp proxy mbslist Show the IGMP proxy membership database (merge of all learned groups. SYNTAX: igmp proxy mbslist E-DOC-CTC-20061027-0003 v2.
PAGE 446
IGMP Commands igmp proxy debug clear Clear IGMP proxy statistics. SYNTAX: igmp proxy debug clear RELATED COMMANDS: 424 igmp proxy debug stats Print IGMP proxy statistics. igmp proxy debug traceconfig Modify IGMP proxy trace configuration. E-DOC-CTC-20061027-0003 v2.
PAGE 447
IGMP Commands igmp proxy debug stats Print IGMP proxy statistics.
PAGE 448
IGMP Commands igmp proxy debug traceconfig Modify IGMP proxy trace configuration. SYNTAX: igmp proxy debug traceconfig [state = <{disabled | enabled}>] where: state Enable or disable tracing. The default is disabled. OPTIONAL RELATED COMMANDS: 426 igmp proxy debug clear Clear IGMP proxy statistics. igmp proxy debug stats Print IGMP proxy statistics. E-DOC-CTC-20061027-0003 v2.
PAGE 449
Interface Commands 21 Interface Commands Introduction This chapter describes the commands of the interface command group. Contents This chapter covers the following commands: interface list E-DOC-CTC-20061027-0003 v2.0 Display interfaces.
PAGE 450
Interface Commands interface list Display interfaces. SYNTAX: interface list [expand = <{disabled | enabled}>] [reverse = <{disabled | enabled}>] where: 428 expand Enable or disable expanded listing of interfaces. The default is disabled. OPTIONAL reverse Enable or disable reverse listing (lower layer first instead of upper layer first). The default is disabled. OPTIONAL E-DOC-CTC-20061027-0003 v2.
PAGE 451
Interface Commands EXAMPLE: =>interface list Name Type State Use UL Interfaces ethif1 physical connected 1 bridge ethif4 physical connected 1 bridge usbif1 physical connected 1 bridge RELAY eth connected 1 Internet_ppp bridge eth connected 1 eth0 atm_0_35 atm connected 1 ethoa_0_35 atm_8_35 atm connected 1 ethoa_8_35 ethoa_0_35 eth connected 0 ethoa_8_35 eth connected 0 Internet_ppp ppp not-connected 1 Internet Internet ip not-connected 0 eth0 ip connected 0 => =>interface list expand=enabled Name Type Sta
PAGE 452
Interface Commands 430 E-DOC-CTC-20061027-0003 v2.
PAGE 453
IP Commands 22 IP Commands Introduction This chapter describes the commands of the ip command group. Contents This chapter covers the following commands: ip arpadd Add an entry to the ARP cache of a broadcast Internet Protocol (IP) interface. 433 ip arpdelete Delete an entry from the ARP cache. 434 ip arplist Display the ARP cache. 435 ip config Show/set global IP stack configuration options. 436 ip flush Flush all the static IP parameters. 438 ip ifadd Create an IP interface.
PAGE 454
IP Commands 432 ip debug sendto Send UDP packets. 468 ip debug stats Display IP statistics. 470 ip debug traceconfig Display/modify the IP stack trace configuration. 471 E-DOC-CTC-20061027-0003 v2.
PAGE 455
IP Commands ip arpadd Add an entry to the ARP cache of a broadcast Internet Protocol (IP) interface. SYNTAX: ip arpadd intf = ip = [hwaddr = ] where: intf The IP interface name. REQUIRED ip The IP address (or range) of the entry to be added to the Address Resolution Protocol (ARP) cache. REQUIRED hwaddr The hardware address (for example the Ethernet MAC address) of the entry to be added.
PAGE 456
IP Commands ip arpdelete Delete an entry from the ARP cache. SYNTAX: ip arpdelete intf = ip = [hwaddr = ] where: intf The IP interface name. REQUIRED ip The IP address (or range) of the entry to be deleted. REQUIRED hwaddr The hardware address (for example the Ethernet MAC address) of the entry to be deleted. OPTIONAL EXAMPLE: =>ip arplist Interface IP-address HW-address Type 2 eth0 10.0.0.1 00:10:a4:ad:32:cf STATIC 2 eth0 10.0.0.
PAGE 457
IP Commands ip arplist Display the ARP cache. SYNTAX: ip arplist EXAMPLE: =>ip arplist Interface 2 eth0 2 eth0 2 eth0 => IP-address 10.0.0.1 10.0.0.2 10.0.0.3 HW-address 00:10:a4:ad:32:cf 00:00:00:00:00:00 00:a0:24:ae:66:e1 Type STATIC DYNAMIC STATIC RELATED COMMANDS: ip arpadd Add an entry to the ARP cache of a broadcast Internet Protocol (IP) interface. ip arpdelete Delete an entry from the ARP cache. E-DOC-CTC-20061027-0003 v2.
PAGE 458
IP Commands ip config Show/set global IP stack configuration options.
PAGE 459
IP Commands addrcheck Set the level of IP address checks. Choose between: > off: No address checking is performed. For advanced users only; in normal circumstances there should always be some kind of address checking. > own: Minimum level of checking. OPTIONAL Only the address configuration on the Thomson ST is checked.
PAGE 460
IP Commands ip flush Flush all the static IP parameters. Dynamic configurations (for example from PPP or CIP links) remain. i The flush command does not impact previously saved configurations. ! The command :ip flush deletes all local IP connectivity. Do not use this command during an IP based local connection, for example a Telnet CLI session, or web based CLI access. SYNTAX: ip flush 438 E-DOC-CTC-20061027-0003 v2.
PAGE 461
IP Commands ip ifadd Create an IP interface. SYNTAX: ip ifadd intf = dest = where: intf The name of the IP interface to be created. REQUIRED dest An network interface name.
PAGE 462
IP Commands ip ifattach Attach an IP interface. SYNTAX: ip ifattach intf = where: intf The name of the IP interface to be attached.
PAGE 463
IP Commands ip ifconfig Configure the parameters of an IP interface. SYNTAX: ip ifconfig intf = [mtu = ] [status = <{down | up}>] [hwaddr = ] [group = or number] [linksensing = <{disabled | enabled}>] [primary = <{disabled | enabled}>] [mcastpromisc = <{disabled|enabled}>] where: intf The name of the IP interface to be configured. REQUIRED mtu A number between 68 and 65535.
PAGE 464
IP Commands EXAMPLE: =>ip iflist Interface Group MTU 0 loop local 65535 1 Internet wan 1500 2 RtPPPoE_ppp wan 1500 3 LocalNetwork lan 1500 4 myIPintf wan 1500 =>ip ifconfig intf = myIPintf [mtu] = 1500 [status] = up [hwaddr] = 00:0e:50:0f:fc:2c [group] = wan [linksensing] = enabled [primary] = enabled :ip ifconfig intf=myIPintf =>ip iflist Interface Group MTU 0 loop local 65535 1 Internet wan 1500 2 RtPPPoE_ppp wan 1500 3 LocalNetwork lan 1500 4 myIPintf wan 1500 => i 442 RX 123966 0 0 86589 0 TX 75177
PAGE 465
IP Commands ip ifdelete Delete an IP interface. SYNTAX: ip ifdelete intf = where: intf The name of the IP interface to be deleted.
PAGE 466
IP Commands ip ifdetach Detach an IP interface. SYNTAX: ip ifdetach intf = where: intf The name of the IP interface to be detached. REQUIRED EXAMPLE: =>ip iflist expand=enabled Interface Group MTU RX TX TX-Drop Status HW-address 0 loop local 65535 130597 82240 0 [UP] 00:0e:50:0f:fc:2c BRHW-address : ff:ff:ff:ff:ff:ff RX unicastpkts: 1304 brcastpkts : 0 TX unicastpkts: 1994 brcastpkts : 0 droppkts:0 Oper state : UP Admin State: UP Flags : ARP BROADCAST ARPTABLE LOOP MULTICAST INTERNAL ...
PAGE 467
IP Commands ip iflist Display all the IP interfaces. SYNTAX: ip iflist [expand = <{disabled | enabled}>] [string = ] [beginstring = ] where: expand Enable or disable expanded listing. The default is disabled.
PAGE 468
IP Commands ip ifwait Wait for a status change of an IP interface. SYNTAX: ip ifwait intf = [timeout = ] [adminstatus = <{down | up}>] [operstatus = <{down | up}>] [linkstatus = <{down | up}>] where: intf The IP interface name. REQUIRED timeout A number between 1 and 600000 (seconds). Represents the timeout. OPTIONAL adminstatus The administrative state of the interface. Choose between: OPTIONAL > > operstatus up. The operational state of the interface.
PAGE 469
IP Commands ip ipadd Assign an IP address to an IP interface. SYNTAX: ip ipadd intf = addr = [netmask = ] [pointopoint = ] [addroute = <{disabled | enabled}>] where: intf The IP interface name. REQUIRED addr The new IP address to be added. REQUIRED netmask The subnetmask associated with this address. OPTIONAL pointopoi nt The remote IP address in case of a dedicated point-to-point link.
PAGE 470
IP Commands ip ipconfig Modify an IP address configuration. SYNTAX: ip ipconfig addr = [preferred = <{disabled | enabled}>] [primary = <{disabled | enabled}>] where: addr The IP address to be configured. REQUIRED preferred Make this IP address the preferred address for that subnet (enabled) or not (disabled). The default is disabled. OPTIONAL primary Make this IP address the primary address for the interface (enabled) or not (disabled). The default is disabled.
PAGE 471
IP Commands ip ipdelete Remove an IP address from an IP interface. SYNTAX: ip ipdelete addr = where: addr The IP address to be deleted. REQUIRED EXAMPLE: =>ip iplist Interface 1 eth0 1 eth0 1 eth0 0 loop Type Ethernet Ethernet Ethernet Ethernet =>ip ipdelete addr=10.0.0.2 =>ip iplist Interface Type 1 eth0 Ethernet 1 eth0 Ethernet 0 loop Ethernet IP-address 10.0.0.2 10.0.0.138 169.254.141.11 127.0.0.1 Point-to-point/Mask 255.255.255.0 255.255.255.0 255.255.0.0 255.0.0.
PAGE 472
IP Commands ip iplist Display all the configured IP addresses. SYNTAX: ip iplist EXAMPLE: =>ip iplist Interface 2 LocalNetwork 2 LocalNetwork 0 loop => Type Ethernet Ethernet Ethernet IP-address 10.0.0.138 *192.168.1.254 127.0.0.1 Point-to-point/Mask 255.255.255.0 255.255.255.0 255.255.255.255 RELATED COMMANDS: 450 ip ipadd Assign an IP address to an IP interface. ip ipdelete Remove an IP address from an IP interface. E-DOC-CTC-20061027-0003 v2.
PAGE 473
IP Commands ip mcast rtadd Add a multicast route to the multicast routing table. SYNTAX: ip mcast rtadd srcintf = [src = ] grp = dstintf = [ttl = ] [ttlincr = {disabled | enabled}] where: srcintf The source IP interface. REQUIRED src The source IP address. OPTIONAL grp The multicast group IP address. REQUIRED dstintf The destination IP interface. REQUIRED ttl The time-to-live for that destination IP interface.
PAGE 474
IP Commands ip mcast rtdelete Delete a multicast route from the multicast routing table. SYNTAX: ip mcast rtdelete srcintf = [src = ] grp = dstintf = where: srcintf The source IP interface. REQUIRED src The source IP address. OPTIONAL grp The multicast group IP address. REQUIRED dstintf The destination IP interface. REQUIRED RELATED COMMANDS: 452 ip mcast rtadd Add a multicast route to the multicast routing table.
PAGE 475
IP Commands ip mcast rtlist Display the multicast routing table. SYNTAX: ip mcast rtlist [expand = <{disabled | enabled}>}] where: expand Enable or disable expanded listing. The default is disabled. OPTIONAL RELATED COMMANDS: ip mcast rtadd Add a multicast route to the multicast routing table. ip mcast rtdelete Delete a multicast route from the multicast routing table. ip mcast flush Flush the multicast routing table. E-DOC-CTC-20061027-0003 v2.
PAGE 476
IP Commands ip mcast flush Flush the multicast routing table. SYNTAX: ip mcast flush RELATED COMMANDS: 454 ip mcast rtadd Add a multicast route to the multicast routing table. ip mcast rtdelete Delete a multicast route from the multicast routing table. ip mcast rtlist Display the multicast routing table. E-DOC-CTC-20061027-0003 v2.
PAGE 477
IP Commands ip rtadd Add a route to the routing table. SYNTAX: ip rtadd dst = [dstmsk = ] [label = ] [gateway = ] [intf = ] [srcintf = ] [metric = ] where: dst The destination IP address(es) for this route. Note REQUIRED Supports ip/mask notation. dstmsk The destination IP address mask. OPTIONAL label The name of the label.
PAGE 478
IP Commands EXAMPLE: =>ip rtlist Destination Label Gateway Intf Mtrc Status 10.0.0.0/24 10.0.0.140 eth0 0 [UP] 10.0.0.140/32 10.0.0.140 eth0 0 [UP] 127.0.0.1/32 127.0.0.1 loop 0 [UP] =>ip rtadd dst=10.10.0.0/24 label=Interactive gateway=10.0.0.140 =>ip rtlist Destination Label Gateway Intf Mtrc Status 10.0.0.0/24 10.0.0.140 eth0 0 [UP] 10.10.0.0/24 Interactive 10.0.0.140 eth0 0 [UP] 10.0.0.140/32 10.0.0.140 eth0 0 [UP] 127.0.0.1/32 127.0.0.
PAGE 479
IP Commands ip rtdelete Delete a route from the routing table. SYNTAX: ip rtdelete dst = [dstmsk = ] [label = ] [gateway = ] [intf = ] where: dst The destination IP address(es) for this route. Note REQUIRED Supports cidr notation. dstmsk The destination IP address mask. OPTIONAL label The name of the label. OPTIONAL gateway The IP address of the next hop. The next hop must be directly connected.
PAGE 480
IP Commands ip rtlist Display the routing table. SYNTAX: ip rtlist [expand = <{disabled | enabled}>] where: expand Enable or disable expanded listing. The default is disabled. OPTIONAL EXAMPLE: =>ip rtlist Destination Label 10.0.0.138/32 127.0.0.1/32 10.0.0.0/24 =>ip rtlist expand=enabled Destination Label 10.0.0.138/ 32 127.0.0.1 127.0.0.1/ 32 127.0.0.1 10.0.0.0/ 24 10.0.0.138 => Gateway 127.0.0.1 127.0.0.1 10.0.0.
PAGE 481
IP Commands ip auto flush Flush the autoIP interfaces. SYNTAX: ip auto flush E-DOC-CTC-20061027-0003 v2.
PAGE 482
IP Commands ip auto ifadd Create an autoIP interface. SYNTAX: ip auto ifadd intf = [addr = ] where: intf The name of the IP interface for which a link-local address has to be allocated. REQUIRED dest The preferred link-local IP address. OPTIONAL EXAMPLE: =>ip auto ifadd intf=eth0 => ip auto iflist eth0 : [INIT] 0.0.0.0 poolstart = 169.254.1.1 claim : 10 defence : 5 probes sent = 0 collisions = 0 poolend = 169.254.254.254 netmask = 255.255.0.
PAGE 483
IP Commands ip auto ifattach Select and assign a link-local address to an autoIP interface. SYNTAX: ip auto ifattach intf = where: intf The name of the autoIP interface for which a link-local address has to be attached. REQUIRED EXAMPLE: => ip auto iflist ipsec0 : [INIT] 0.0.0.0 poolstart = 169.254.1.1 claim : 10 defence : 5 probes sent = 0 collisions = 0 poolend = 169.254.254.254 netmask = 255.255.0.
PAGE 484
IP Commands ip auto ifconfig Configure an autoIP interface. SYNTAX: ip auto ifconfig intf = [addr = ] [poolstart = ] [poolend = ] [netmask = ] [claim = ] [defence = ] [probe = ] [interval = ] where: 462 intf The name of the autoIP interface to be configured. REQUIRED addr The preferred link-local IP address.
PAGE 485
IP Commands EXAMPLE: => ip auto iflist eth0 : [INIT] 0.0.0.0 poolstart = 169.254.1.1 claim : 10 defence : 5 probes sent = 0 collisions = 0 poolend = 169.254.254.254 netmask = 255.255.0.0 probe : 4 interval : 2 (sec) =>ip auto ifconfig intf=ipsec0 claim=5 probe=5 => ip auto iflist ipsec0 : [INIT] 0.0.0.0 poolstart = 169.254.1.1 poolend = 169.254.254.254 netmask = 255.255.0.0 claim : 5 defence : 5 probe : 5 interval : 2 (sec) probes sent = 0 collisions = 0 => E-DOC-CTC-20061027-0003 v2.
PAGE 486
IP Commands ip auto ifdelete Delete an existing autoIP interface. SYNTAX: ip auto ifdelete intf = where: intf The name of the IP interface to be deleted. REQUIRED EXAMPLE: =>ip auto iflist ipsec0 : [SELECTING] poolstart = claim : 10 probes sent collisions 169.254.80.236 169.254.1.1 poolend = 169.254.254.254 netmask = 255.255.0.
PAGE 487
IP Commands ip auto ifdetach Release the link-local address for the given autoIP interface. SYNTAX: ip auto ifdetach intf = where: intf The name of the autoIP interface for which a link-local address has to be detached. REQUIRED EXAMPLE: =>ip auto iflist ipsec0 : [SELECTING] poolstart = claim : 10 probes sent collisions 169.254.80.236 169.254.1.1 poolend = 169.254.254.254 netmask = 255.255.0.
PAGE 488
IP Commands ip auto iflist Display the autoIP interfaces. SYNTAX: ip auto iflist [intf = ] where: intf The name of the autoIP interface to be listed. Note OPTIONAL If not specified, all the autoIP interfaces are shown. EXAMPLE: =>ip auto iflist eth0 : [CLAIMED] 169.254.138.1 poolstart = 169.254.1.1 claim : 10 defence : 5 probes sent = 2 collisions = 0 poolend = 169.254.254.254 netmask = 255.255.0.
PAGE 489
IP Commands ip debug httpprobe Send a HTTP probe. This HTTP probe will measure the Round Trip Time (RTT) taken to connect and access data from a HTTP server. SYNTAX: ip debug httpprobe url = [version = <{1.0 | 1.1}>] where: url The Uniform Resource Locator (URL) identifying the HTTP server. REQUIRED version The version of the HTTP server. The default is 1.0. OPTIONAL EXAMPLE: The first example shows the measured time for a file that was downloaded: =>ip httpprobe url=http://download.
PAGE 490
IP Commands ip debug sendto Send UDP packets. SYNTAX: ip debug sendto addr = [count = ] [size = ] [interval = ] [listen = <{disabled | enabled}>] [dffield = <{disabled | enabled}>] [srcaddr = ] [srcport = ] dstport = [dstintf = ] where: 468 addr The destination IP address. REQUIRED count A number between 1 and 1000000. Represents the number of UDP packets to send.
PAGE 491
IP Commands EXAMPLE: =>ip debug sendto addr=10.0.0.148 listen=on srcport=19 dstport=1025 =>ip debug sendto addr=10.0.0.148 listen=on srcport=19 dstport=1025 1 bytes from 10.0.0.148:1025 41 A =>ip debug sendto addr=10.0.0.148 count=3 listen=on srcport=19 dstport=1025 1 bytes from 10.0.0.148:1025 41 A 1 bytes from 10.0.0.148:1025 41 A 1 bytes from 10.0.0.148:1025 41 A => E-DOC-CTC-20061027-0003 v2.
PAGE 492
IP Commands ip debug stats Display IP statistics.
PAGE 493
IP Commands ip debug traceconfig Display/modify the IP stack trace configuration.
PAGE 494
IP Commands EXAMPLE: =>ip debug traceconfig Input traces : none Forward traces : none Output traces : none Drop traces : all Path traces : none Trace mode : line ARP traces : none => EXAMPLE: =>ip debug traceroute addr = 192.193.195.250 count=3 size=1 interval=1000 maxhops=30 dstport= 33433 maxfail=5 type=icmp utime=yes :ip debug traceroute addr=192.193.195.250 ttl=1 192.193.195.250 676 us 1351 us 648 us => 472 E-DOC-CTC-20061027-0003 v2.
PAGE 495
IPQoS Commands 23 IPQoS Commands Introduction This chapter describes the commands of the ipqos command group. Contents This chapter covers the following commands: ipqos config Configure IPQoS for a given destination interface for the IPQoS queues instantiation. 474 ipqos list Display the IPQoS configuration. 477 ipqos ef config Configure the IPQoS Expedited Forwarding (EF) timer for an interface. 478 ipqos ef list Display the IPQoS EF timers.
PAGE 496
IPQoS Commands ipqos config Configure IPQoS for a given destination interface for the IPQoS queues instantiation. When enabling or disabling IPQoS, take the following into account: i > if the WAN interface (for example PPPoA, IP oA,...) is detached at the time of enabling/disabling IPQoS, then the WAN interface has to be attached in order for the enabling/disabling of IPQoS to take effect.
PAGE 497
IPQoS Commands priority Select the subqueue priority algorithm. Choose between: > wfq: Weighted Fair Queuing (WFQ) is used for the four AF queues. The realtime queue has priority over the WFQ queues, which have priority over the best-effort queue. > strict: Priority queuing is used. Strict Priority scheduling is used between all queues. The higher the queue number, the higher the priority. > wrr: Weighted Round Robin (WRR) is used for the four AF queues.
PAGE 498
IPQoS Commands EXAMPLE: =>ipqos config dest=atm_pvc_8_35 state=enabled =>ipqos list Name State Discard Priority Size (Packets) atm_pvc_0_35 disabled early wfq 250 atm_pvc_8_35 enabled early wfq 250 => Size (KBytes) 56 56 Rate (%) 80% 80% Burst (KBytes) 2 2 Weights Weights 25% 25% 25% 25% 25% 25% 25% 25% RELATED COMMANDS: ipqos list 476 Display the IPQoS configuration. E-DOC-CTC-20061027-0003 v2.
PAGE 499
IPQoS Commands ipqos list Display the IPQoS configuration. SYNTAX: ipqos list EXAMPLE: =>ipqos list Name State atm_pvc_0_35 disabled % atm_pvc_8_35 enabled % => Discard Priority wfq Size Size (Packets) (KBytes) 250 56 Rate (%) 80% Burst (KBytes) 2 Weights Weights 25% 25% 25% 25 early early wfq 250 80% 2 25% 25% 25% 25 56 RELATED COMMANDS: ipqos config E-DOC-CTC-20061027-0003 v2.0 Configure IPQoS for a given destination interface for the IPQoS queues instantiation.
PAGE 500
IPQoS Commands ipqos ef config Configure the IPQoS Expedited Forwarding (EF) timer for an interface. SYNTAX: ipqos ef config intf = [state = <{disabled | enabled}>] [timeout = ] [mtu = ] where: intf The name of the IP interface. REQUIRED state Enable or disable the IPQoS EF timer for the interface. The default is disabled. OPTIONAL timeout A number between 100 and 10000 milliseconds. Represents the timeout. The default is 1000.
PAGE 501
IPQoS Commands ipqos ef list Display the IPQoS EF timers. SYNTAX: ipqos ef list EXAMPLE: =>ipqos ef list Interface State loop Rt_PPPoA2 eth0 => disabled enabled disabled Timeout (ms) 1000 1000 1000 MTU (bytes) 65535 1500 1500 RELATED COMMANDS: ipqos ef config Configure the IPQoS Expedited Forwarding (EF) timer for an interface. ipqos ef stats Display the IPQoS EF timer statistics. E-DOC-CTC-20061027-0003 v2.
PAGE 502
IPQoS Commands ipqos ef stats Display the IPQoS EF timer statistics. SYNTAX: ipqos ef stats EXAMPLE: =>ipqos ef stats Interface State loop Rt_PPPoA2 eth0 => active active disabled Remain (ms) 900 900 0 RELATED COMMANDS: 480 ipqos ef config Configure the IPQoS Expedited Forwarding (EF) timer for an interface. ipqos ef list Display the IPQoS EF timers. E-DOC-CTC-20061027-0003 v2.
PAGE 503
IPQoS Commands ipqos queue clear Clear the IPQoS statistics.
PAGE 504
IPQoS Commands ipqos queue config Modify the IPQoS subqueue configuration. SYNTAX: ipqos queue config dest = queue = [propagate = <{disabled | enabled}>] [ecnmarking = <{disabled | enabled}>] [ackfiltering = <{disabled | enabled}>] [maxpackets = ] [maxbytes = ] [respackets = ] [resbytes = ] [hold = ] [markprob = ] where: dest The destination interface for the IPQoS queues instantiation.
PAGE 505
IPQoS Commands maxbytes A number between 0 and 128. Represents the maximum size in kilobytes of this queue. The default is 0 for the Real time queue and 20 for the other queues. Note OPTIONAL 0 means that a maximum size is not enforced. respackets A number between 0 and 250. Represents the reserved number of packets in this queue. The default is 30 for the Real time queue and 13 for the other queues.
PAGE 506
IPQoS Commands ipqos queue list Display the IPQoS subqueue configuration. SYNTAX: ipqos queue list [dest = ] where: dest The destination interface for the IPQoS queues instantiation. This is an ATM phonebook entry. Note OPTIONAL If not specified, the IPQoS subqueue configuration for all the interfaces will be shown.
PAGE 507
IPQoS Commands ipqos queue stats Show the IPQoS subqueue statistics. SYNTAX: ipqos queue stats [dest = ] where: dest The destination interface for the IPQoS queues instantiation. This is an ATM phonebook entry. Note OPTIONAL If not specified, the IPQoS subqueue statistics for all the interfaces will be shown.
PAGE 508
IPQoS Commands 486 E-DOC-CTC-20061027-0003 v2.
PAGE 509
Label Commands 24 Label Commands Introduction This chapter describes the commands of the label command group. Contents This chapter covers the following commands: label add Create a new label. 488 label delete Delete a label. 489 label flush Flush all labels. 490 label list Display the labels. 491 label modify Modify a label configuration. 492 label chain add Add a new label chain. 495 label chain delete Delete a label chain. 496 label chain flush Flush all label chains.
PAGE 510
Label Commands label add Create a new label. SYNTAX: label add name = where: name The name of the label to be added.
PAGE 511
Label Commands label delete Delete a label. SYNTAX: label delete name = [force = <{disabled | enabled}>] where: name The name of the label to be deleted. REQUIRED force Force delete and cleanup references even when the label is still in use (enabled) or not (disabled). The default is disabled.
PAGE 512
Label Commands label flush Flush all labels. i The flush command does not impact previously saved configurations. SYNTAX: label flush 490 E-DOC-CTC-20061027-0003 v2.
PAGE 513
Label Commands label list Display the labels. SYNTAX: label list [name = ] where: name The name of the label to be displayed. Note OPTIONAL If not specified, all the labels will be displayed.
PAGE 514
Label Commands label modify Modify a label configuration.
PAGE 515
Label Commands ackclass The priority class of the ACK segments of the TCP connection. Choose between: > > > OPTIONAL A number between 0 and 15 prioritize defclass. The default is 0. bidirectional The label applies to the initiator stream, the returning stream (the current connection) as well as to the child connections (enabled) or not (disabled). The default is disabled.
PAGE 516
Label Commands EXAMPLE: =>label list Name Class Def Ack Bidirect Inherit Tosmark Type Value Use Trace DSCP overwrite dscp defclass disabled disabled disabled tos 0 0 0 disabled Interactive increase 8 8 disabled disabled disabled tos 0 0 0 disabled Management increase 12 12 disabled disabled disabled tos 0 0 0 disabled Video increase 10 10 disabled disabled disabled tos 0 0 0 disabled VoIP overwrite 14 14 enabled enabled disabled tos 0 0 0 disabled default increase default prioritize disabled disabled disab
PAGE 517
Label Commands label chain add Add a new label chain. SYNTAX: label chain add chain = where: chain The name of the chain to be added.
PAGE 518
Label Commands label chain delete Delete a label chain. SYNTAX: label chain delete chain = where: chain The name of the chain to be deleted.
PAGE 519
Label Commands label chain flush Flush all label chains. SYNTAX: label chain flush E-DOC-CTC-20061027-0003 v2.
PAGE 520
Label Commands label chain list Display a list of chains. SYNTAX: label chain list [format = <{pretty | cli}>] where: format OPTIONAL Select the output format of the list. Choose between: > pretty: the configuration is shown as intuitive output in clear text. > cli: the configuration is shown via the CLI commands configuration. The default is pretty.
PAGE 521
Label Commands label rule add Add a label rule. SYNTAX: label rule add i chain = [index = ] [name = ] [clink = ] [srcintf [!]= ] [srcip [!]= <{ip address | private}>] [dstip [!]= <{ip address | private}>] [serv [!]= <{service name}>] [log = <{disabled | enabled}>] [state = <{disabled | enabled}>] label = If a value is preceded by a “!”, it means NOT. For example “srcintf=!wan” means “if srcintf is different from WAN”.
PAGE 522
Label Commands EXAMPLE: =>label rule list Rules (flags: C=Constant, D=Dynamic, E=Enable, L=Log) ===== Chain Nr. Flags Rule --------------------------------------------------------------------------------------------routing_labels 1 CDE : link rt_user_labels 2 CDE : link rt_default_labels qos_labels 1 CDE : link qos_user_labels 2 CDE : link qos_default_labels qos_default_labels 1 C E : VoIP sip *.* > *.* 2 C E : VoIP h323 *.* > *.* 3 C E : Interactive telnet *.* > *.* 4 C E : Interactive smtp *.* > *.
PAGE 523
Label Commands label rule list E-DOC-CTC-20061027-0003 v2.0 Display a list of label rules.
PAGE 524
Label Commands label rule delete Delete a label rule. SYNTAX: label rule delete chain = index = where: chain The name of the chain in which a rule must be deleted. REQUIRED index The index number of the rule in the chain. REQUIRED Tip Use the command :label rule list to obtain the index number of the applicable rule. EXAMPLE: =>label rule list Rules (flags: C=Constant, D=Dynamic, E=Enable, L=Log) ===== Chain Nr.
PAGE 525
Label Commands RELATED COMMANDS: label rule add Add a label rule. label rule list Display a list of label rules. E-DOC-CTC-20061027-0003 v2.
PAGE 526
Label Commands label rule flush Flush all label rules. The chains themselves are not removed. i The flush command does not impact previously saved configurations. SYNTAX: label rule flush [chain = ] where: chain The name of the chain to be flushed. Note 504 OPTIONAL If not specified, all the rules for all the chains are flushed. E-DOC-CTC-20061027-0003 v2.
PAGE 527
Label Commands label rule list Display a list of label rules. SYNTAX: label rule list [chain = ] [format = <{pretty | cli}>] [string = ] [beginstring = ] where: chain The name of the chain for which the rules must be listed. Note format OPTIONAL If not specified, all rules for all chains are shown. Select the output format of the list. Choose between: > pretty: the configuration is shown as intuitive output in clear text.
PAGE 528
Label Commands EXAMPLE: =>label rule list format=cli :label rule add chain=qos_default_labels label=VoIP :label rule add chain=qos_default_labels label=VoIP :label rule add chain=qos_default_labels label=Interactive :label rule add chain=qos_default_labels label=Interactive :label rule add chain=qos_default_labels label=Interactive :label rule add chain=qos_default_labels label=Interactive :label rule add chain=qos_default_labels label=Interactive :label rule add chain=qos_default_labels label=Interactive
PAGE 529
Label Commands label rule modify Modify a label rule. SYNTAX: label rule modify i chain = index = [newindex = ] [name = ] [clink = ] [srcintf [!]= ] [srcip [!]= <{ip address | private}>] [dstip [!]= <{ip address | private}>] [serv [!]= <{service name}>] [log = <{disabled | enabled}>] [state = <{disabled | enabled}>] [label = ] If a value is preceded by a “!”, it means “NOT”.
PAGE 530
Label Commands label rule debug clear Clear the label rule statistics. SYNTAX: label rule debug clea r [chain = ] [index = ] where: chain The name of the chain in which the rule is to be found. Note index If not specified, the statistics for all the rules in all chains will be cleared. The index number (determined by the position) of the rule in the chain. Note 508 OPTIONAL OPTIONAL If not specified, the statistics for all the rules in a chain will be cleared.
PAGE 531
Label Commands EXAMPLE: =>label rule debug stats chain=qos_labels chain index packets bytes -----------------------------------------------------------qos_labels 1 0 0 2 203 19146 =>label rule debug clear chain=qos_labels =>label rule debug stats chain index packets bytes -----------------------------------------------------------routing_labels 1 0 0 2 0 0 qos_labels 1 0 0 2 0 0 qos_default_labels 1 0 0 2 0 0 3 4 168 4 0 0 5 0 0 6 0 0 7 0 0 8 0 0 9 0 0 10 0 0 11 0 0 12 0 0 13 10 480 14 3 144 15 0 0 16 0 0
PAGE 532
Label Commands label rule debug stats Display the label rule statistics. SYNTAX: label rule debug stat s [chain = ] [index = ] where: chain The name of the chain for which the statistics must be shown. Note index If not specified, the statistics for the rules applicable to all chains are shown. The index number of the rule for which the statistics must be shown. Tip Note OPTIONAL OPTIONAL Use the command :label rule list to obtain the index number of the applicable rule.
PAGE 533
Label Commands label rule debug traceconfig Display or modify the rule trace configuration. SYNTAX: label rule debug trac econfig [trace = <{disabled | enabled}>] where: trace Disable or enable rule traces. The default is disabled. OPTIONAL EXAMPLE: =>label rule debug traceconfig :label rule debug traceconfig state=disabled => E-DOC-CTC-20061027-0003 v2.
PAGE 534
Label Commands 512 E-DOC-CTC-20061027-0003 v2.
PAGE 535
Language Commands 25 Language Commands Introduction This chapter describes the commands of the language command group. Contents This chapter covers the following commands: language config Select a language. 514 language delete Delete one or all language archives. 515 language list List the available language archives. 516 E-DOC-CTC-20061027-0003 v2.
PAGE 536
Language Commands language config Select a language. SYNTAX: language config [language = ] [complete = <{yes | no}>] where: language Language code: OSI language code (2 chars) for language. Example: en for english. OPTIONAL complete Enable translation for expert pages. The default is yes. OPTIONAL EXAMPLE: =>language config language : en complete : no => RELATED COMMANDS: 514 language delete Delete one or all language archives. language list List the available language archives.
PAGE 537
Language Commands language delete Delete one or all language archives. SYNTAX: language delete [file = ] [all = <{yes | no}>] where: file The filename of the language archive to be removed. OPTIONAL all Remove all languages archives (yes) or not (no). The default is no. OPTIONAL RELATED COMMANDS: language config Select a language. language list List the available language archives. E-DOC-CTC-20061027-0003 v2.
PAGE 538
Language Commands language list List the available language archives. SYNTAX: language list EXAMPLE: =>language list CODE LANGUAGE en* English => i VERSION 5.3.0.10.0 FILENAME The currently selected language is indicated by a “*” next to the OSI language code. RELATED COMMANDS: 516 language config Select a language. language delete Delete one or all language archives. E-DOC-CTC-20061027-0003 v2.
PAGE 539
MBUS Commands 26 MBUS Commands Introduction This chapter describes the commands of the mbus command group. Contents This chapter covers the following commands: mbus client config Modify client parameters. 518 mbus client exec Execute mbus command. 519 mbus client register Register cli client to mbus. 521 mbus debug stats Display mbus statistics. 522 mbus debug clearstats Reset MBUS statistics . 523 mbus debug traceconfig Modify mbus trace settings.
PAGE 540
MBUS Commands mbus client config Modify client parameters. SYNTAX: mbus client config [writelock = <{enabled | disabled}>] [wlgetimeout = ] [wlidletimeout = ] [path = ] [type = ] where: writelock Enable or disable mbus writelock. The default is enabled. OPTIONAL wlgetimeout Writelock get timeout in seconds. OPTIONAL wlidletimeout Writelock idle timeout in seconds.
PAGE 541
MBUS Commands mbus client exec Execute mbus command. SYNTAX: mbus client exec cmd = <{addobject | deleteobject | getparamattributes | getparamcount | getparamnames | getparamvalues | getpath | setparamvalue}> [param = ] [value = ] [gettype = <{object | parameter | path}>] [depth = ] [processcmd = <{disabled | enabled}>] [readcommitted = <{disabled | enabled}>] [onerrorrollback = <{disabled | enabled}>] where: cmd Mbus command name.
PAGE 542
MBUS Commands RELATED COMMANDS: 520 mbus client config Modify client parameters. mbus client register Register cli client to mbus. mbus debug stats Display mbus statistics. E-DOC-CTC-20061027-0003 v2.
PAGE 543
MBUS Commands mbus client register Register cli client to mbus. SYNTAX: mbus client register RELATED COMMANDS: mbus client config Modify client parameters. mbus client exec Execute mbus command. mbus debug stats Display mbus statistics. E-DOC-CTC-20061027-0003 v2.
PAGE 544
MBUS Commands mbus debug stats Display mbus statistics. SYNTAX: mbus debug stats RELATED COMMANDS: mbus debug traceconfig 522 Modify mbus trace settings. E-DOC-CTC-20061027-0003 v2.
PAGE 545
MBUS Commands mbus debug clearstats Reset MBUS statistics . SYNTAX: mbus debug clearstats RELATED COMMANDS: mbus debug stats Display mbus statistics. mbus debug traceconfig Modify mbus trace settings. E-DOC-CTC-20061027-0003 v2.
PAGE 546
MBUS Commands mbus debug traceconfig Modify mbus trace settings. SYNTAX: mbus debug traceconfig [level = ] where: level A number between 0 and 4. Represents the mbus trace level. OPTIONAL RELATED COMMANDS: mbus debug stats 524 Display mbus statistics. E-DOC-CTC-20061027-0003 v2.
PAGE 547
MBUS Commands mbus listobjects Display the object instances. SYNTAX: mbus listobjects [path = [type = [output [expand ] <{idpath | keypath}>] = <{list | tree}>] = <{disabled | enabled}>] where: path Fully qualified mbus path to list. OPTIONAL type Path type. Choose between: OPTIONAL > > idpath keypath. The default is idpath. output List output type. Choose between: > > OPTIONAL list tree. The default is tree. expand Enable or disable details. The default is disabled.
PAGE 548
MBUS Commands mbus listtypes Display the registered objecttypes. SYNTAX: mbus listtypes [path = ] [expand = <{disabled | enabled}>] where: path Fully qualified mbus path to list. OPTIONAL expand Enable or disable details. The default is disabled.
PAGE 549
MBUS Commands mbus listenums Display the registered enumtypes. SYNTAX: mbus listenumss [dmtree = <{igd|atomic|system}>] [name = ] [expand = <{disabled|enabled}>] where: dmtree Select mbusd datamodel tree. OPTIONAL name Filter enumtypes by (part of) the name OPTIONAL expand Enable or disable details. The default is disabled.
PAGE 550
MBUS Commands mbus listcontexts Display the context instances . SYNTAX: listcontexts [dmtree = <{igd|atomic|system}>] where: dmtree Select mbusd datamodel tree. OPTIONAL RELATED COMMANDS: 528 mbus listobjects Display the object instances. mbus listtypes Display the registered objecttypes. mbus listenums Display the registered enumtypes. mbus listsubscriptions Display the subscription instances . E-DOC-CTC-20061027-0003 v2.
PAGE 551
MBUS Commands mbus listsubscriptions Display the subscription instances . SYNTAX: listsubscriptions [dmtree = <{igd|atomic|system}>] where: dmtree Select mbusd datamodel tree. OPTIONAL RELATED COMMANDS: mbus listobjects Display the object instances. mbus listtypes Display the registered objecttypes. mbus listenums Display the registered enumtypes. mbus listcontexts Display the context instances . E-DOC-CTC-20061027-0003 v2.
PAGE 552
MBUS Commands mbus debug loadobjects Load object instances of registered objecttypes. SYNTAX: mbus debug loadobjects [dmtree = <{igd|atomic|system}>] [path = ] [type = <{indexpath|objidpath|keystrpath}>] [flush = <{disabled|enabled}>] where: dmtree mbus data model tree OPTIONAL path Fully qualified mbus path. OPTIONAL type Path type. The default is indexpath.
PAGE 553
MBUS Commands mbus debug unloadobjects Unload object instances. SYNTAX: mbus unloadobjects [path = ] [type = <{idpath | keypath}>] where: path Fully qualified mbus path. OPTIONAL type Path type. Choose between: OPTIONAL > > idpath keypath. The default is idpath. RELATED COMMANDS: mbus debug loadobjects E-DOC-CTC-20061027-0003 v2.0 Load object instances of registered objecttypes.
PAGE 554
MBUS Commands mbus pluginevent Simulate event from plugin . SYNTAX: mbus pluginevent ctxid = type = <{addobj|delobj|updobj}> path = [name = ] [value = ] [orivalue = ] where: 532 ctxid Plugin context id type Event type path Plugin event subpath name Plugin event name value Plugin event value orivalue Plugin event orivalue E-DOC-CTC-20061027-0003 v2.
PAGE 555
MBUS Commands mbus unregister Unregister a client/plugin context . SYNTAX: unregister id = where: id E-DOC-CTC-20061027-0003 v2.0 message-based client/plugin context id.
PAGE 556
MBUS Commands mbus client unregister Unregister cli client from mbus . SYNTAX: unregister 534 E-DOC-CTC-20061027-0003 v2.
PAGE 557
MEMM Commands 27 MEMM Commands Introduction This chapter describes the commands of the memm command group. Contents This chapter covers the following commands: memm debug lock traceconfig Modify lock trace settings. 536 memm debug traceconfig Modify memm trace settings. 537 memm debug clearstats Display memm statistics. 541 memm debug lock stats Display memm statistics. 541 memm listobjects Display objects. 540 memm stats Display memm statistics. 541 E-DOC-CTC-20061027-0003 v2.
PAGE 558
MEMM Commands memm debug lock traceconfig Modify lock trace settings. SYNTAX: memm debug lock traceconfig [level = ] [name = ] where: 536 level A number between 0 and 4. Represents the memm trace level. OPTIONAL name Application name filter for lock traces (empty displays all lock traces). OPTIONAL E-DOC-CTC-20061027-0003 v2.
PAGE 559
MEMM Commands memm debug traceconfig Modify memm trace settings. SYNTAX: memm debug traceconfig [level = ] where: level E-DOC-CTC-20061027-0003 v2.0 A number between 0 and 4. Represents the memm trace level.
PAGE 560
MEMM Commands memm debug clearstats Clear time statistics SYNTAX: memm debug clearstats 538 E-DOC-CTC-20061027-0003 v2.
PAGE 561
MEMM Commands memm debug lock stats Display lock statistics SYNTAX: memm debug lock stats E-DOC-CTC-20061027-0003 v2.
PAGE 562
MEMM Commands memm listobjects Display objects. SYNTAX: memm listobjects [name = ] where: name 540 Select typename(s) to list (supports partial typename). OPTIONAL E-DOC-CTC-20061027-0003 v2.
PAGE 563
MEMM Commands memm stats Display memm statistics. SYNTAX: memm stats [name = ] where: name Select typename(s) to list (supports partial typename).
PAGE 564
MEMM Commands EXAMPLE: =>memm stats pool name cur,max,avail ------------memm_pooldesc j: 0, 255 dynstr_pool 0, 0, mbus_llist 0, 0, mbus_dynstr 0, 0, - strings buffer mbus_client 0, 0, mbus_cmddata 0, 0, mbus_objecttype 0, 0, mbus_paramtype 0, 0, mbus_object 0, 0, mbus_objectindex 0, 0, upnp_dynstr 0, 0, - strings buffer upnp_handles 0, 0, upnp_devices 0, 0, upnp_services 0, 0, upnp_subscriptions 0, 0, upnp_firstdeviceevents 0, 0, mbus_cliclient 0, 0, cwmp_elem_pool 0, 0, cwmp_attr_pool 0, 0, cwmp_llist_poo
PAGE 565
MLP Commands 28 MLP Commands Introduction This chapter describes the commands of the mlp command group. Contents This chapter covers the following commands: mlp flush Flush all the Multi-Level access Policies (MLP) structures. 544 mlp import Import all the scores. 545 mlp debug export Export all the scores. 546 mlp debug stats Display MLP statistics. 547 mlp debug traceconfig Modify the MLP trace settings. 548 mlp privilege add Add a privilege.
PAGE 566
MLP Commands mlp flush Flush all the Multi-Level access Policies (MLP) structures. SYNTAX: mlp flush 544 E-DOC-CTC-20061027-0003 v2.
PAGE 567
MLP Commands mlp import Import all the scores. SYNTAX: mlp import [trace = <{disabled | enabled | full}>] where: trace Select the import trace level. Choose between: > > > OPTIONAL disabled enabled full. The default is disabled. RELATED COMMANDS: mlp debug export E-DOC-CTC-20061027-0003 v2.0 Export all the scores.
PAGE 568
MLP Commands mlp debug export Export all the scores. SYNTAX: mlp debug export RELATED COMMANDS: mlp import 546 Import all the scores. E-DOC-CTC-20061027-0003 v2.
PAGE 569
MLP Commands mlp debug stats Display MLP statistics. SYNTAX: mlp debug stats EXAMPLE: =>mlp debug stats Roles (cur/free/max) : 8/7/15 Privileges (cur/free/max) : 35/25/60 ListItems (cur/free/max) : 31/119/150 => E-DOC-CTC-20061027-0003 v2.
PAGE 570
MLP Commands mlp debug traceconfig Modify the MLP trace settings. SYNTAX: mlp debug traceconfig [trace = <{disabled | enabled | full}>] where: trace Select the trace level. Choose between: > > > OPTIONAL disabled enabled full. The default is disabled. EXAMPLE: =>mlp debug traceconfig mlp trace: disabled => 548 E-DOC-CTC-20061027-0003 v2.
PAGE 571
MLP Commands mlp privilege add Add a privilege. SYNTAX: mlp privilege add name = type = <{access | service}> [descr = ] where: name The name of the new privilege. Note type descr REQUIRED access: the privilege is an access privilege. service: the privilege is a service privilege. A description of the privilege. Note E-DOC-CTC-20061027-0003 v2.0 The maximum number of privileges is 60. Select the privilege type.
PAGE 572
MLP Commands EXAMPLE: =>mlp privilege list type=access Privilege (type) Description ---------------------------anyaccess (access) All access privileges granted AP1 (access) LAN_Local_all AP2 (access) LAN_Local with all secured channels AP3 (access) LAN_Local with all channels & access to sensitive files ...
PAGE 573
MLP Commands mlp privilege addzone Add a zone to a privilege. i Only one zone can be added at a time to a privilege. If multiple zones need to be added, the command :mlp privilege addzone must be executed for each zone to be added. SYNTAX: mlp privilege addzone name = zone = where: name The name of the privilege in which a zone must be added. REQUIRED zone The name of the new zone.
PAGE 574
MLP Commands mlp privilege config Modify a privilege. SYNTAX: mlp privilege config name = [descr = ] [score = <{hex-word}[:{hex-word}] ex: 'a12:c30f'>] where: name The name of the privilege to be modified. REQUIRED descr Set the privilege description. OPTIONAL Note score The maximum length is 63 characters. Set the score of the privilege. Note OPTIONAL This is a hexadecimal value, for example “a12:c30f”.
PAGE 575
MLP Commands mlp privilege delete Delete a privilege. SYNTAX: mlp privilege delete name = where: name The name of the privilege to be deleted.
PAGE 576
MLP Commands RELATED COMMANDS: 554 mlp privilege delete Add a privilege. mlp privilege list Display the privileges. E-DOC-CTC-20061027-0003 v2.
PAGE 577
MLP Commands mlp privilege list Display the privileges. SYNTAX: mlp privilege list [name = ] [type = <{access | service}>] [verbose = <{minimal | medium | all}>] where: name The name of the privilege to be listed. Note type service: only the service privileges will be shown. If not specified, all the privilege types will be shown. Limit the output list.
PAGE 578
MLP Commands EXAMPLE: =>mlp privilege list type=service Privilege (type) Description ---------------------------anyservice (service) All service privileges granted SP1 (service) Limited_Read SP2 (service) detailed_Read SP3 (service) Write_to_LAN SP4 (service) Write_FWD_RT_normal_FW_cfgs SP5 (service) cooperative_cfgs SP6 (service) Remote Configurations SP7 (service) Advanced sink & source FW SP8 (service) Write_to_U_Connection SP9 (service) Write_to_Local SP10 (service) Simple_network_debugging SP11 (servi
PAGE 579
MLP Commands mlp privilege removezone Remove a zone from a privilege. i Only one zone can be removed at a time from a privilege. If multiple zones need to be removed, the command :mlp privilege removezone must be executed for each zone to be removed. SYNTAX: mlp privilege removezone name = zone = where: name The name of the privilege in which a zone must be removed. REQUIRED zone The name of the zone to be removed.
PAGE 580
MLP Commands mlp role add Add a role. SYNTAX: mlp role add name = parent = [descr = ] where: name The name of the new role. Note REQUIRED The maximum number of roles is 15. parent The name of the parent role. REQUIRED descr The role description. OPTIONAL Note The maximum length is 63 characters.
PAGE 581
MLP Commands mlp role list E-DOC-CTC-20061027-0003 v2.0 Display the roles.
PAGE 582
MLP Commands mlp role addpriv Add a privilege to a role. SYNTAX: mlp role addpriv name = access = service = where: name The name of the role. REQUIRED access The name of the access privilege to be added. REQUIRED service The name of the service privilege to be added.
PAGE 583
MLP Commands mlp role config Modify the role. SYNTAX: mlp role config name = [parent = ] [descr = ] where: name The name of the role to be configured. REQUIRED parent The name of the parent role. OPTIONAL descr The role description. OPTIONAL Note The maximum length is 63 characters.
PAGE 584
MLP Commands mlp role delete Delete a role. SYNTAX: mlp role delete name = where: name The name of the role to be deleted.
PAGE 585
MLP Commands mlp role list Display the roles. SYNTAX: mlp role list [name = ] [verbose = <{minimal | medium | all}>] where: name The name of the role to be listed. Note verbose If not specified, all the roles will be listed. Limit the output list. Choose between: > > > OPTIONAL OPTIONAL minimal medium all. The default is minimal.
PAGE 586
MLP Commands mlp role removepriv Remove a privilege from a role. SYNTAX: mlp role removepriv name = access = [service = ] where: name The name of the role. REQUIRED access The name of the access privilege to be deleted. REQUIRED service The name of the service privilege to be deleted.
PAGE 587
NAT Commands 29 NAT Commands Introduction This chapter describes the commands of the nat command group. Contents This chapter covers the following commands: nat config Display/modify global NAT configuration options. 566 nat flush Flush the current NAT configuration. 567 nat ifconfig Modify address translation on an IP interface. 568 nat iflist Display the address translation configuration on all the interfaces.
PAGE 588
NAT Commands nat config Display/modify global NAT configuration options. SYNTAX: nat config [trace = <{disabled | enabled}>] where: trace Enable or disable traces. The default is disabled. REQUIRED EXAMPLE: =>nat config NAT traces : disabled =>nat config trace=enabled =>nat config NAT traces : enabled => 566 E-DOC-CTC-20061027-0003 v2.
PAGE 589
NAT Commands nat flush Flush the current NAT configuration. SYNTAX: nat flush E-DOC-CTC-20061027-0003 v2.
PAGE 590
NAT Commands nat ifconfig Modify address translation on an IP interface. SYNTAX: nat ifconfig intf = translation = <{disabled | enabled | transparent}> where: intf The IP interface name. REQUIRED translation Enable or disable address translation. Choose between: REQUIRED > > > disabled: Address translation is disabled. enabled: Address translation is enabled. transparent: An inside address is translated into the same outside IP address.
PAGE 591
NAT Commands nat iflist Display the address translation configuration on all the interfaces. SYNTAX: nat iflist EXAMPLE: =>nat iflist Interface loop Internet RtPPPoE_ppp LocalNetwork => NAT disabled enabled enabled transparent RELATED COMMANDS: nat ifconfig E-DOC-CTC-20061027-0003 v2.0 Modify address translation on an IP interface.
PAGE 592
NAT Commands nat mapadd Add an address mapping to a Network Address Translation (NAT) enabled interface. SYNTAX: nat mapadd intf = [type = <{napt | nat}>] [outside_addr = ] [inside_addr = ] [access_list = ] [foreign_addr = ] [protocol = <{supported IP protocol} or number>] [outside_port = ] [inside_port = ] [mode = <{auto | inbound | outbound}>] where: intf The IP interface name.
PAGE 593
NAT Commands inside_addr The inside (typically private) IP address. > Inbound: Represents the address(es) to be used as destination address after translation. > Outbound: This map will only apply if the source IP address is part of the inside address(es). Allowed values are: > > > An IP address (A.B.C.D or A.D, meaning A.0.0.D). OPTIONAL for NAT maps and NAPT maps. REQUIRED for portshifting maps. A range of IP addresses (A.B.C.[D-E]) (only for NAT). An IP subnet (A.B.C.D/M (only for NAT)).
PAGE 594
NAT Commands outside_port The outside port number or range (only for maps of type napt). > For a NAPT map: Represents the range of TCP/UDP ports to be used as dynamic port range during the NAPT process. > For a port-shifting map: Represents the source port(s) to be translated (shifted) into inside_port. Allowed values are: > > inside_port TCP/UDP port number (only for port-shifting maps). TCP/UDP port number (only for port-shifting maps).
PAGE 595
NAT Commands EXAMPLE: =>nat maplist Idx Type Interface Outside Address Inside Address Use 1 NAPT eth0 any:80 127.0.0.1:8080 0 2 NAPT eth0 any:1080 127.0.0.1:8080 0 3 NAPT eth0 any:8080 127.0.0.1:8080 0 =>nat mapadd intf=myPPP_ppp type=napt outside_addr=100.100.100.1 access_list=10.0.0.0/24 =>nat maplist Idx Type Interface Outside Address Inside Address Use 1 NAPT myPPP_ppp 100.100.100.1 unmapped 0 1 NAPT eth0 any:80 127.0.0.1:8080 0 2 NAPT eth0 any:1080 127.0.0.1:8080 0 3 NAPT eth0 any:8080 127.0.0.
PAGE 596
NAT Commands nat mapdelete Delete an address mapping from a NAT enabled interface. SYNTAX: nat mapdelete intf = index = where: intf The IP interface name. REQUIRED index The map index. REQUIRED Tip Use the command :nat maplist to obtain a list of the mapindexes. EXAMPLE: =>nat maplist Idx Type Interface Outside Address 1 NAPT myPPP_ppp 100.100.100.
PAGE 597
NAT Commands nat maplist Display the address mapping for a NAT enabled interface. SYNTAX: nat maplist [intf = ] [expand = <{disabled | enabled}>] [string = ] [beginstring = ] where: intf The IP interface name. Note OPTIONAL If not specified, the address mapping for all the NAT enabled interfaces will be shown. expand Enable or disable expanded listing. The default is disabled.
PAGE 598
NAT Commands nat tmpladd Add an address mapping template. SYNTAX: nat tmpladd [intf = ] [group = <{wan|local|lan|tunnel|dmz|guest} or number>] [timeout = ] [type = <{napt | nat}>] outside_addr = [inside_addr = ] [access_list = ] [foreign_addr = ] [protocol = <{supported IP protocol} or number>] [outside_port = ] [inside_port = ] [mode = <{auto | inbound | outbound}>] where: intf The IP interface name.
PAGE 599
NAT Commands outside_addr The outside (typically public) IP address. > Inbound: This map will only apply if the destination IP address is part of the outside address(es). > Outbound: Represents the address(es) to be used as source address after translation. Allowed values are: > > > inside_addr An IP address (A.B.C.D or A.D, meaning A.0.0.D). OPTIONAL for portshifting maps. A range of IP addresses (A.B.C.[D-E]) (only for NAT). An IP subnet (A.B.C.D/M) (only for NAT).
PAGE 600
NAT Commands protocol The IP protocol to be used as filter for inbound/outbound traffic. The NAT map only applies if the protocol of the IP packet matches the map protocol. Select an IP protocol (see “ Supported IP Protocols” on page 746) or, alternatively, type the protocol number. The default is 0 (meaning any protocol). OPTIONAL outside_port The outside port number or range (only for maps of type napt). OPTIONAL for NAPT map.
PAGE 601
NAT Commands EXAMPLE: =>nat tmpladd intf=myPPP_ppp type=napt outside_addr=100.100.100.1 =>nat tmpllist Idx Type Interface Ifgroup Outside Address Inside Address Use 1 NAPT myPPP_ppp any 100.100.100.1 unmapped 0 =>nat tmpladd group=lan type=napt outside_addr=100.200.100.1 =>nat tmpllist Idx Type Interface Ifgroup Outside Address Inside Address Use 1 NAPT any lan 100.200.100.1 unmapped 0 2 NAPT myPPP_ppp any 100.100.100.1 unmapped 0 => RELATED COMMANDS: nat tmpldelete Delete an address mapping template.
PAGE 602
NAT Commands nat tmpldelete Delete an address mapping template. SYNTAX: nat tmpldelete index = where: index The index of the address mapping template to be deleted. Tip REQUIRED Use the command :nat tmpllist to view the address mapping templates. EXAMPLE: =>nat tmpllist Idx Type Interface Use 1 NAPT any 0 2 NAPT myPPP_ppp 0 =>nat tmpldelete index=1 =>nat tmpllist Idx Type Interface Use 1 NAPT myPPP_ppp 0 => Ifgroup Outside Address Inside Address lan 100.200.100.1 unmapped any 100.
PAGE 603
NAT Commands nat tmpllist Display the address mapping templates. SYNTAX: nat tmpllist [expand = <{disabled | enabled}>] where: expand Enable or disable expanded listing. The default is disabled. OPTIONAL EXAMPLE: =>nat tmpllist Idx Type Interface Use 1 NAPT any 0 2 NAPT myPPP_ppp 0 => Ifgroup Outside Address Inside Address lan 100.200.100.1 unmapped any 100.100.100.1 unmapped RELATED COMMANDS: nat tmpladd Add an address mapping template. nat tmpldelete Delete an address mapping template.
PAGE 604
NAT Commands nat tmplinst Instantiate address mapping templates for a given dynamic address. SYNTAX: nat tmplinst intf = addr_index = dynamic_addr = where: intf The IP interface name. REQUIRED addr_index The outside IP address index/key to instantiate for. REQUIRED dynamic_addr The dynamic address to substitute the index/key with. REQUIRED EXAMPLE: =>nat tmplinst intf=myPPP_ppp addr_index=100.100.100.1 dynamic_addr=200.200.200.
PAGE 605
PPP Commands 30 PPP Commands Introduction This chapter describes the commands of the ppp command group. Contents This chapter covers the following commands: ppp flush Flush all PPP interfaces. 584 ppp ifadd Create a new PPP interface. 585 ppp ifattach Attach a PPP interface. 587 ppp ifconfig Configure a PPP interface. 589 ppp ifdelete Delete a PPP interface. 594 ppp ifdetach Detach a PPP interface. 596 ppp iflist Display the PPP interfaces.
PAGE 606
PPP Commands ppp flush Flush all PPP interfaces. i The flush command does not impact previously saved configurations. SYNTAX: ppp flush 584 E-DOC-CTC-20061027-0003 v2.
PAGE 607
PPP Commands ppp ifadd Create a new PPP interface. SYNTAX: ppp ifadd intf = where: intf The name for the new PPP interface. Note REQUIRED If not specified, the destination parameter must be specified. In this case the name of the destination will double as interface name.
PAGE 608
PPP Commands RELATED COMMANDS: 586 ppp ifdelete Delete a PPP interface. ppp iflist Display the PPP interfaces. E-DOC-CTC-20061027-0003 v2.
PAGE 609
PPP Commands ppp ifattach Attach a PPP interface. SYNTAX: ppp ifattach intf = where: intf E-DOC-CTC-20061027-0003 v2.0 The name of the PPP interface to be attached.
PAGE 610
PPP Commands EXAMPLE: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr savepwd demanddial dns metric = 0 mru = 1492 Tx inactivity = 1200s left = 0s auth = auto user = password = admin state = down oper state = down link state = not-connected LCP : state = initial retransm = 10 term. reason = IPCP: state = initial retransm = 0 term.
PAGE 611
PPP Commands ppp ifconfig Configure a PPP interface. i The interface to be configured must not be connected at the time of configuration. If this should be the case, use the command :ppp ifdetach before using the command :ppp ifconfig.
PAGE 612
PPP Commands password The password for remote PAP/CHAP authentication. OPTIONAL acname The Access Concentrator name for a PPPoE session. OPTIONAL Use the command :ppp ifscan to obtain the names of available access concentrators, if any. Tip servicename The Service Name for a PPPoE session. OPTIONAL Use the command :ppp ifscan to obtain the available service names, if any. Tip pcomp Try (enabled) or do not try (disabled) to negotiate PPP protocol compression (LCP PCOMP). The default is disabled.
PAGE 613
PPP Commands silent Do not send anything at startup and just listen for incoming LCP messages (enabled) or retry up to 10 times to establish the connection (disabled). The default is disabled. OPTIONAL echo Send LCP echo requests at regular intervals (enabled) or not (disabled). The default is disabled. OPTIONAL mru A number between 293 and 8192. Represents the maximum packet size the Thomson ST should negotiate to be able to receive. The default is 1492.
PAGE 614
PPP Commands dnsmetric A number between 1 and 100. Represents the DNS route metric to be used for the negotiated DNS servers. The default is 1. OPTIONAL idletime A number between 0 and 1000000 (seconds). Represents the maximum time the link may be idle. The default is 0. OPTIONAL idletrigger Consider the link being idle if no traffic is sent and/or received during the idle time. Choose between: OPTIONAL > RxTx: The idle time period restarts when a packet is transmitted or received.
PAGE 615
PPP Commands EXAMPLE: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr savepwd demanddial dns metric = 0 mru = 1492 Tx inactivity = 1200s left = 0s auth = auto user = password = admin state = down oper state = down link state = not-connected LCP : state = initial retransm = 10 term. reason = IPCP: state = initial retransm = 0 term.
PAGE 616
PPP Commands ppp ifdelete Delete a PPP interface. SYNTAX: ppp ifdelete intf = where: intf The name of the PPP interface to be deleted. REQUIRED EXAMPLE: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr savepwd demanddial dns metric = 0 mru = 1492 Tx inactivity = 1200s left = 0s auth = auto user = password = admin state = down oper state = down link state = not-connected LCP : state = initial retransm = 10 term.
PAGE 617
PPP Commands RELATED COMMANDS: ppp ifadd Create a new PPP interface. ppp iflist Display the PPP interfaces. E-DOC-CTC-20061027-0003 v2.
PAGE 618
PPP Commands ppp ifdetach Detach a PPP interface. SYNTAX: ppp ifdetach intf = where: intf 596 The name of the PPP interface to be detached. REQUIRED E-DOC-CTC-20061027-0003 v2.
PAGE 619
PPP Commands EXAMPLE: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr savepwd demanddial dns metric = 0 mru = 1492 Tx inactivity = 1200s left = 0s auth = auto user = password = admin state = down oper state = down link state = not-connected LCP : state = initial retransm = 10 term. reason = IPCP: state = initial retransm = 0 term.
PAGE 620
PPP Commands ppp iflist Display the PPP interfaces. SYNTAX: ppp iflist [intf = ] [string = ] [beginstring = ] where: intf The name of the PPP interface. Note OPTIONAL If not specified, all PPP interfaces are shown.
PAGE 621
PPP Commands ppp ifscan Scan a PPPoE interface for available Access Concentrator and Service names. i Use the command :ppp ifdetach for this interface before performing a scan on it. SYNTAX: ppp ifscan intf = [time = ] where: intf The name of the PPPoE interface to be scanned. REQUIRED time A number between 0 and 36000 (seconds). Represents the time to scan for services.
PAGE 622
PPP Commands ppp rtadd Add a route to the routing table when the PPP link comes up. This route configuration will determine which local hosts are allowed to use this link and/or which remote destinations should be or should not be reachable. i The interface must not be connected when a route configuration is added. If this should be the case, use the command :ppp ifdetach for this interface prior to configuring routes.
PAGE 623
PPP Commands metric The route metric, in other words, the cost factor of the route. Practically, the cost is determined by the hop count. OPTIONAL EXAMPLE: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr savepwd demanddial dns metric = 0 mru = 1492 Tx inactivity = 1200s left = 0s auth = auto user = password = admin state = down oper state = down link state = not-connected LCP : state = initial retransm = 10 term.
PAGE 624
PPP Commands ppp rtdelete Delete the route for a PPP link. i The interface must not be connected when a route configuration must be deleted. If the interface is connected, use the command :ppp ifdetach for this interface. SYNTAX: ppp rtdelete intf = where: intf 602 The PPP interface name for which to delete the route settings. REQUIRED E-DOC-CTC-20061027-0003 v2.
PAGE 625
PPP Commands EXAMPLE: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr savepwd demanddial dns metric = 0 mru = 1492 Tx inactivity = 1200s left = 0s auth = auto user = password = admin state = down oper state = down link state = not-connected LCP : state = initial retransm = 10 term. reason = IPCP: state = initial retransm = 0 term.
PAGE 626
PPP Commands ppp relay flush Remove all Ethernet interfaces from the PPP relay agent list and terminate all sessions. i The flush command does not impact previously saved configurations. SYNTAX: ppp relay flush 604 E-DOC-CTC-20061027-0003 v2.
PAGE 627
PPP Commands ppp relay ifadd Add an Ethernet interface to the PPP relay list. SYNTAX: ppp relay ifadd intf = where: intf The Ethernet interface to be added to the PPP relay agent list.
PAGE 628
PPP Commands ppp relay ifconfig Modify an ethernet interface from the PPP relay agent list. SYNTAX: ppp relay ifconfig intf = hwaddr = where: 606 inft The ethernet intf to be added to the PPP relay agent list. REQUIRED hwaddr The hardware address (e.g. Ethernet MAC address) of this interface. REQUIRED E-DOC-CTC-20061027-0003 v2.
PAGE 629
PPP Commands ppp relay ifdelete Delete an Ethernet interface from the PPP relay agent list. SYNTAX: ppp relay ifdelete intf = where: intf The Ethernet interface to be deleted from the PPP relay agent list.
PAGE 630
PPP Commands ppp relay iflist Display all Ethernet interfaces added to the PPP relay agent list. SYNTAX: ppp relay iflist where: intf The Ethernet interface to be added to the PPP relay agent list. REQUIRED EXAMPLE: =>ppp relay iflist # Interface 1 ethoa_0_35 2 ethoa_8_35 => HWaddr Status 00-0e-50-0f-fc-2d connected 00-0e-50-0f-fc-2d connected RELATED COMMANDS: 608 ppp relay ifadd Add an Ethernet interface to the PPP relay list.
PAGE 631
PPP Commands ppp relay sesslist Add an Ethernet interface to the PPP relay list. SYNTAX: ppp relay ifadd intf = where: intf E-DOC-CTC-20061027-0003 v2.0 The Ethernet interface to be added to the PPP relay agent list.
PAGE 632
PPP Commands 610 E-DOC-CTC-20061027-0003 v2.
PAGE 633
PPTP Commands 31 PPTP Commands Introduction This chapter describes the commands of the pptp command group. Contents This chapter covers the following commands: pptp ifadd Add a Point-to-Point Tunneling Protocol (PPTP) profile. 612 pptp flush Flush the complete PPTP configuration. 613 pptp list Show the current PPTP configuration. 614 pptp profadd Define a new PPTP profile. 615 pptp profdelete Delete a PPTP profile. 617 pptp proflist Display all the current PPTP profiles.
PAGE 634
PPTP Commands pptp ifadd Add a Point-to-Point Tunneling Protocol (PPTP) profile. i Backwards compatible with previous release, use profiles instead. SYNTAX: pptp ifadd dest = [rate = ] [encaps = <{vcmux | nlpid}>] [ac = <{never | always | keep}>] where: dest The WAN destination for this PPTP tunnel. Typically a phonebook entry. REQUIRED rate A number between 10 and 10000. Represents the transmission speed (in bits/s) for the WAN link.
PAGE 635
PPTP Commands pptp flush Flush the complete PPTP configuration. i The flush command does not impact previously saved configurations. SYNTAX: pptp flush E-DOC-CTC-20061027-0003 v2.
PAGE 636
PPTP Commands pptp list Show the current PPTP configuration. SYNTAX: pptp list EXAMPLE: =>pptp list Dialstr Destination DIALUP_PPP3 => 614 QoS default Encaps vcmux AC never State CONNECTED User (10.0.0.2) E-DOC-CTC-20061027-0003 v2.
PAGE 637
PPTP Commands pptp profadd Define a new PPTP profile. SYNTAX: pptp profadd name = [qos = ] [encaps = <{vcmux | nlpid}>] [ac = <{never | always | keep}>] where: name The name of the new PPTP profile. REQUIRED qos The name of the qosbook entry, containing the settings for this profile. OPTIONAL Note encaps This parameter never needs to be specified. The type of WAN protocol encapsulation to be used with this PPTP profile. Choose between: > > OPTIONAL VC-MUX NLPID.
PAGE 638
PPTP Commands RELATED COMMANDS: 616 pptp profdelete Define a new PPTP profile. pptp proflist Display all the current PPTP profiles. E-DOC-CTC-20061027-0003 v2.
PAGE 639
PPTP Commands pptp profdelete Delete a PPTP profile. SYNTAX: pptp profdelete name where: name The name of the PPTP profile to be deleted. REQUIRED EXAMPLE: =>pptp proflist Profile QoS Encaps Relay_PPP1 default nlpid PPTPLink default vcmux =>pptp profdelete name=PPTPLink =>pptp proflist Profile QoS Encaps Relay_PPP1 default nlpid => AC always never AC always RELATED COMMANDS: pptp profadd Define a new PPTP profile. pptp proflist Display all the current PPTP profiles.
PAGE 640
PPTP Commands pptp proflist Display all the current PPTP profiles. SYNTAX: pptp proflist EXAMPLE: =>pptp proflist Profile QoS Relay_PPP1 default PPTPLink default => Encaps nlpid vcmux AC always never RELATED COMMANDS: 618 pptp profadd Define a new PPTP profile. pptp profdelete Delete a PPTP profile. E-DOC-CTC-20061027-0003 v2.
PAGE 641
Script Commands 32 Script Commands Introduction This chapter describes the commands of the script command group. Scripting is not a general purpose mechanism but is only used in the autoPVC/ILMI mechanism. ! It is recommended not to change the default scripts. Contents This chapter covers the following commands: script add Add a line to a script. 620 script delete Delete a complete script or a line from a script. 621 script flush Flush all scripts.
PAGE 642
Script Commands script add Add a line to a script. SYNTAX: script add name = [index = ] command = where: name Name of the script in which a line must be added. REQUIRED index Line number OPTIONAL Note command Use 0 to add a line. Command. REQUIRED RELATED COMMANDS: 620 script delete Delete a complete script or a line from a script. script list Display a script or all scripts. E-DOC-CTC-20061027-0003 v2.
PAGE 643
Script Commands script delete Delete a complete script or a line from a script. SYNTAX: script delete name = [index = ] where: name Name of the script to be deleted. REQUIRED index Line number to be deleted. OPTIONAL Tip Note Use the command :script list to view the line numbers. If not specified, the complete script will be deleted. RELATED COMMANDS: script add Add a line to a script. script list Display a script or all scripts. E-DOC-CTC-20061027-0003 v2.
PAGE 644
Script Commands script flush Flush all scripts. i The flush command does not impact previously saved configurations. SYNTAX: script flush 622 E-DOC-CTC-20061027-0003 v2.
PAGE 645
Script Commands script list Display a script or all scripts. SYNTAX: script list [name = ] where: name Name of the script to be listed. Note OPTIONAL If not specified, all the scripts are displayed. EXAMPLE Some of the default scripts are shown below: =>script list Script: autopvc_add_qos 0: qosbook add name _auto_$1_$2 class $3 tx_peakrate $4 tx_sustrate $5 tx_maxburst $ 6 rx_peakrate $4 rx_sustrate $5 rx_maxburst $6 dynamic yes ...
PAGE 646
Script Commands RELATED COMMANDS: 624 script add Add a line to a script. script delete Delete a complete script or a line from a script. E-DOC-CTC-20061027-0003 v2.
PAGE 647
Script Commands script run Run a script. SYNTAX: script run name = pars = where: name Name of the script to be run. Tip pars E-DOC-CTC-20061027-0003 v2.0 REQUIRED Use the command :script list to obtain the names of the different scripts. Parameters separated with comma. For example a,b,c.
PAGE 648
Script Commands 626 E-DOC-CTC-20061027-0003 v2.
PAGE 649
Service Commands 33 Service Commands Introduction This chapter describes the commands of the service command group. Contents This chapter covers the following commands: service host assign Assign a service to a host device. 628 service host config Modify and/or display global service configuration options. 629 service host add Add a host service. 630 service host delete Delete a host service. 631 service host disable Disable a host service. 632 service host flush Flush all host services.
PAGE 650
Service Commands service host assign Assign a service to a host device. SYNTAX: service host assign name = [host = ] [log = <{disabled|enabled}>] where: name The name of an existing host service. REQUIRED host The IP address of the host. OPTIONAL log Enable or disable logging. OPTIONAL EXAMPLE: =>service host assign name="MSN Messenger" host=192.168.1.
PAGE 651
Service Commands service host config Modify and/or display global service configuration options. SYNTAX: service host config [trace = <{disabled | enabled}>] where: trace Enable or disable traces. The default is disabled. REQUIRED EXAMPLE: =>service host config Service traces : disabled l=> E-DOC-CTC-20061027-0003 v2.
PAGE 652
Service Commands service host add Add a host service. SYNTAX: service host add name = [mode = <{server | client | custom}>] where: name The name of the new host service. REQUIRED mode The service mode. Choose between: OPTIONAL > > > server: The service is defined for server purposes. client: The service is defined for client purposes. custom: The service is a user created service (in other words, a customized service). The default is custom.
PAGE 653
Service Commands service host delete Delete a host service. SYNTAX: service host delete name = where: name The name of the host service to be deleted. REQUIRED EXAMPLE: =>service host list Service Name Host User-Defined Mode --------------------------------------------------------------------------Age of Empires unassigned server AIM Talk unassigned client ...
PAGE 654
Service Commands service host disable Disable a host service. SYNTAX: service host disable [name = ] where: name The name of the host service to be disabled. Note OPTIONAL If not specified, all the host services will be disabled. EXAMPLE: =>service host list Service Name Host User-Defined Mode --------------------------------------------------------------------------Age of Empires unassigned server AIM Talk unassigned client Aliens vs. Predator unassigned server .. MSN Messenger 192.
PAGE 655
Service Commands service host flush Flush all host services. SYNTAX: service host flush E-DOC-CTC-20061027-0003 v2.
PAGE 656
Service Commands service host list Display a list of host services. SYNTAX: service host list [name = ] [string = ] [beginstring = ] where: name The name of the host service to be listed. Note REQUIRED If not specified, all the host services will be listed.
PAGE 657
Service Commands service host stats Show the host service statistics. SYNTAX: service host stats EXAMPLE: =>service host Services : Service maps : Trigger ports: => E-DOC-CTC-20061027-0003 v2.0 stats 113 of 150 in use. 225 of 300 in use. 0 of 25 in use.
PAGE 658
Service Commands service host triggerlist List all triggers. SYNTAX: service host triggerlist EXAMPLE: =>service triggerlist Ip Triggerport -----------=> 636 Portrange --------- Timeout ------- E-DOC-CTC-20061027-0003 v2.
PAGE 659
Service Commands service host rule add Create/define a host service portmap. SYNTAX: service host rule add name = [protocol = <{any|tcp|udp} or number>] [baseport = ] portrange = [triggerport = ] [triggerprotocol = <{any|tcp|udp} or number>] where: name The name of the host service. REQUIRED protocol The IP protocol type. Choose between: OPTIONAL > > > > baseport any tcp udp a number. The inbound base port.
PAGE 660
Service Commands service host rule delete Delete a host service portmap. SYNTAX: service host rule delete name = [protocol = <{any|tcp|udp} or number>] [baseport = ] portrange = [triggerport = ] [triggerprotocol = <{any|tcp|udp} or number>] where: name The name of the host service. REQUIRED protocol The IP protocol type. Choose between: OPTIONAL > > > > baseport any tcp udp a number. The inbound base port.
PAGE 661
Service Commands service system ifadd Add an interface group to the access list. SYNTAX: service system ifadd name = group = <{wan|local|lan|tunnel|dmz|guest} or number> where: name The name of the system service for this access list. REQUIRED group The interface group for this access list.
PAGE 662
Service Commands service system ifdelete Delete an interface group from the access list. SYNTAX: service system ifdelete name = group = <{wan|local|lan|tunnel|dmz|guest} or number> where: name The name of the system service for this access list. REQUIRED group The interface group for this access list.
PAGE 663
Service Commands service system ipadd Add an IP address (range) to the access list. SYNTAX: service system ipadd name = ip = where: name The name of the system service for this access list. REQUIRED ip The IP address (range) for this access list. REQUIRED EXAMPLE: =>service system list name=SIPPBX expand=enabled Idx Name Protocol SrcPort DstPort Group State --------------------------------------------------------------------------------1 SIPPBX udp 5060 disabled Description....
PAGE 664
Service Commands service system ipdelete Delete an IP address (range) from the access list. SYNTAX: service system ipdelete name = ip = where: name The name of the system service for this access list. REQUIRED ip The IP address (range) for this access list.
PAGE 665
Service Commands service system list Display the system services. SYNTAX: service system list [name = ] [expand = <{disabled | enabled}>] [dynamics = <{disabled | enabled}>] [members = <{disabled | enabled}>] [string = ] [beginstring = ] where: name The name of the system service to be displayed. Note OPTIONAL If not specified, all the system services will be displayed. expand Enable or disable expanded listing. The default is disabled.
PAGE 666
Service Commands EXAMPLE: =>service system list Idx Name Protocol SrcPort DstPort Group State --------------------------------------------------------------------------------1 DNS-C udp 53 enabled 2 SNTP udp 123 123 enabled 3 SLA_ICMP_PING icmp 8 enabled 4 SLA_UDP_PING udp 7 enabled 5 SLA_ICMP_TRRT icmp 8 enabled 6 SLA_UDP_TRRT udp 33434 enabled 7 SYSLOG udp 514 enabled 8 HTTP tcp 80 enabled 9 HTTPs tcp 443 enabled 10 HTTPI tcp 8080 enabled 11 FTP tcp 21 enabled 12 TELNET tcp 23 enabled 13 RIP udp 520 520
PAGE 667
Service Commands service system mapadd Add a port map for a system service. SYNTAX: service system mapadd name = <{string}> intf = <{auto|loop|Internet|LocalNetwork}> port = where: name The name of the system service for this map. REQUIRED intf The interface for this map. REQUIRED port The port for this map. Select one of the supported TCP/UDP port names (see “ Supported TCP/UDP Port Names” on page 747) or, alternatively, specify the port number.
PAGE 668
Service Commands service system mapdelete Delete a port map for a system service. SYNTAX: service system mapdelete name = intf = <{auto|loop|Internet|LocalNetwork}> port = where: name The name of the system service for this map. REQUIRED intf The interface for this map. REQUIRED port The port for this map. Select one of the supported TCP/UDP port names (see “ Supported TCP/UDP Port Names” on page 747) or, alternatively, specify the port number.
PAGE 669
Service Commands service system modify Modify a system service. SYNTAX: service system modify name = [state = <{disabled | enabled}>] [port = ] [srcintf = ] [log = <{disabled|enabled}>] [qoslabel = <{None|DSCP|Interactive| Management|Video|VoIP|default}>] [routelabel = <{None|DSCP|Interactive| Management|Video|VoIP|default}>] [natpmweight = ] [forward = <{disabled|enabled}>] where: name The name of the system service for this map.
PAGE 670
Service Commands 648 E-DOC-CTC-20061027-0003 v2.
PAGE 671
SNMP Commands 34 SNMP Commands Introduction This chapter describes the commands of the snmp command group. Contents This chapter covers the following commands: snmp config Show/set global Simple Network Management Protocol (SNMP) parameters. 650 snmp get Get from the supplied SNMP Object IDentifier (OID). 651 snmp getnext GetNext from the supplied SNMP OID. 652 snmp walk Walk from the supplied SNMP OID. 653 snmp community add Configure an SNMP community string to allow SNMP access over IP.
PAGE 672
SNMP Commands snmp config Show/set global Simple Network Management Protocol (SNMP) parameters. SYNTAX: snmp config [sysContact = ] [sysName = ] [sysLocation = ] where: sysContact The SNMP system contact. The default is Service Provider. OPTIONAL sysName The SNMP system name. OPTIONAL sysLocation The SNMP system location. The default is Customer Premises.
PAGE 673
SNMP Commands snmp get Get from the supplied SNMP Object IDentifier (OID). For example: get ObjectId=.1.3.6.1.2.1.1.1.0. SYNTAX: snmp get [ObjectId = ] where: ObjectID The Object Identifier. Object ID to get from ... must include the instance which is 0 for scalar objects, for example .1.3.6.1.2.1.1.1.0 sysDescription. Note OPTIONAL If not specified, the sysDescription OID .1.3.6.1.2.1.1.1.0 is assumed. Its value is Thomson ST. EXAMPLE: =>snmp get VB_octetStr => .1.3.6.1.2.1.1.1.
PAGE 674
SNMP Commands snmp getnext GetNext from the supplied SNMP OID. SYNTAX: snmp getnext [ObjectId = ] where: ObjectID The Object Identifier. Object ID to getnext from for example .1.3.6.1.2.1.1 system returns sysDescription. OPTIONAL EXAMPLE: =>snmp getnext ObjectId=.1.3.6.1.2.1.1.4.0 VB_octetStr .1.3.6.1.2.1.1.5.0 => Sascha RELATED COMMANDS: 652 snmp get Get from the supplied SNMP Object IDentifier (OID). snmp walk Walk from the supplied SNMP OID. E-DOC-CTC-20061027-0003 v2.
PAGE 675
SNMP Commands snmp walk Walk from the supplied SNMP OID. SYNTAX: snmp walk [ObjectId = ] where: ObjectID The Object Identifier. Object ID to walk from for example .1.3.6.1.2.1.1 system walks the system group. OPTIONAL EXAMPLE: =>snmp walk ObjectId=.1.3.6.1.2.1.1 VB_octetStr .1.3.6.1.2.1.1.1.0 VB_objId .1.3.6.1.2.1.1.2.0 VB_timeTicks .1.3.6.1.2.1.1.3.0 VB_octetStr .1.3.6.1.2.1.1.4.0 VB_octetStr .1.3.6.1.2.1.1.5.0 VB_octetStr .1.3.6.1.2.1.1.6.0 VB_integer .1.3.6.1.2.1.1.7.0 => Thomson ST 620 .
PAGE 676
SNMP Commands snmp community add Configure an SNMP community string to allow SNMP access over IP. SYNTAX: snmp community add securityname = <{RWCommunity | ROCommunity}> communityname = where: securityname Configure access rights/restrictions control for the community name. Choose between: > > communityname REQUIRED RWCommunity: read/write access rights ROCommunity: read only access rights. Configure the SNMP community name.
PAGE 677
SNMP Commands snmp community delete Delete an SNMP community string to prevent SNMP access over IP. SYNTAX: snmp community delete securityname = <{RWCommunity | ROCommunity}> where: securityname Select the access rights/restrictions control for the community name to be deleted. Choose between: > > REQUIRED RWCommunity: read/write access rights ROCommunity: read only access rights.
PAGE 678
SNMP Commands snmp community list List all SNMP community strings in use for SNMP access over IP. SYNTAX: snmp community list EXAMPLE: =>snmp community list Read-write SNMP community name Read-only SNMP community name => : : ***** ***** RELATED COMMANDS: 656 snmp community add Configure an SNMP community string to allow SNMP access over IP. snmp community delete Delete an SNMP community string to prevent SNMP access over IP. E-DOC-CTC-20061027-0003 v2.
PAGE 679
SNMP Commands snmp community modify Modify an SNMP community string to allow SNMP access over IP. SYNTAX: snmp community modify securityname = <{RWCommunity | ROCommunity}> communityname = where: securityname Configure access rights/restrictions control for the community name. Choose between: > > communityname E-DOC-CTC-20061027-0003 v2.0 REQUIRED RWCommunity: read/write access rights ROCommunity: read only access rights. Configure the SNMP community name.
PAGE 680
SNMP Commands snmp ifadd Create a new SNMP interface. SYNTAX: snmp ifadd intf = dest = where: intf The name for the new SNMP interface. REQUIRED dest The destination interface for this SNMP interface. REQUIRED EXAMPLE: =>snmp ifadd intf = new dest = Internet :snmp ifadd intf=new dest=Internet => RELATED COMMANDS: 658 snmp ifdelete Delete an SNMP interface. snmp ifattach Attach an SNMP interface. snmp ifdetach Detach an SNMP interface.
PAGE 681
SNMP Commands snmp ifdelete Delete an SNMP interface. SYNTAX: snmp ifdelete intf = where: intf The name of the SNMP interface. REQUIRED EXAMPLE: =>snmp ifdelete intf = new :snmp ifdelete intf=new => RELATED COMMANDS: snmp ifadd Create a new SNMP interface. snmp ifattach Attach an SNMP interface. snmp ifdetach Detach an SNMP interface. snmp ifconfig Modify an SNMP interface. snmp iflist Display the SNMP interfaces. E-DOC-CTC-20061027-0003 v2.
PAGE 682
SNMP Commands snmp ifattach Attach an SNMP interface. SYNTAX: snmp ifattach intf = where: intf The name of the SNMP interface. REQUIRED EXAMPLE: =>snmp ifattach intf = Internet :snmp ifattach intf=Internet => RELATED COMMANDS: 660 snmp ifadd Create a new SNMP interface. snmp ifdelete Delete an SNMP interface. snmp ifdetach Detach an SNMP interface. snmp ifconfig Modify an SNMP interface. snmp iflist Display the SNMP interfaces. E-DOC-CTC-20061027-0003 v2.
PAGE 683
SNMP Commands snmp ifdetach Detach an SNMP interface. SYNTAX: snmp ifdetach intf = where: intf The name of the SNMP interface. REQUIRED EXAMPLE: =>snmp ifdetach intf = Internet :snmp ifdetach intf=Internet => RELATED COMMANDS: snmp ifadd Create a new SNMP interface. snmp ifdelete Delete an SNMP interface. snmp ifattach Attach an SNMP interface. snmp ifconfig Modify an SNMP interface. snmp iflist Display the SNMP interfaces. E-DOC-CTC-20061027-0003 v2.
PAGE 684
SNMP Commands snmp ifconfig Modify an SNMP interface. SYNTAX: snmp ifconfig intf = [securityname = <{RWCommunity | ROCommunity}>] [communityname = ] where: intf The name of the SNMP interface to configure. REQUIRED securityname Configure access rights/restrictions control for the community name. Choose between: OPTIONAL > > RWCommunity ROCommunity. The default is RWCommunity. communityname Configure SNMP community name.
PAGE 685
SNMP Commands snmp iflist Display the SNMP interfaces. SYNTAX: snmp iflist [intf = ] where: intf E-DOC-CTC-20061027-0003 v2.0 The name of an SNMP interface to configure.
PAGE 686
SNMP Commands 664 E-DOC-CTC-20061027-0003 v2.
PAGE 687
SNTP Commands 35 SNTP Commands Introduction This chapter describes the commands of the Simple Network Time Protocol (SNTP) command group. Contents This chapter covers the following commands: sntp add Add a Network Time Protocol (NTP) server to the NTP server list. 666 sntp config Modify/display the SNTP client configuration. 667 sntp delete Delete an NTP server from the NTP server list. 668 sntp flush Flush the NTP server list and the SNTP client configuration.
PAGE 688
SNTP Commands sntp add Add a Network Time Protocol (NTP) server to the NTP server list. The internal Thomson ST real time clock (SNTP client) will be synchronized with the NTP server. SYNTAX: sntp add [addr = ] [name = ] [version = ] where: addr The IP address of the NTP server to add to the list. Note name This parameter is optional in this respect that either an IP address or the name of an NTP server must be specified.
PAGE 689
SNTP Commands sntp config Modify/display the SNTP client configuration. SYNTAX: sntp config [state = <{enabled | disabled}>] [poll = ] [pollpresync = ] where: state Enable or disable the Thomson ST SNTP client. The default is enabled. OPTIONAL poll A number between 1 and 60 (minutes). Represents the time interval for the SNTP client to poll the configured NTP server and, if needed, (re-)synchronize its internal clock. The default is 60.
PAGE 690
SNTP Commands sntp delete Delete an NTP server from the NTP server list. SYNTAX: sntp delete [addr = ] [name = ] where: addr The IP address of the NTP server to be removed from the list. Note name OPTIONAL This parameter is optional in this respect that either an IP address or the name of an NTP server must be specified. The DNS name of the NTP server to be removed to the list.
PAGE 691
SNTP Commands sntp flush Flush the NTP server list and the SNTP client configuration. SYNTAX: sntp flush E-DOC-CTC-20061027-0003 v2.
PAGE 692
SNTP Commands sntp list List the NTP servers. SYNTAX: sntp list EXAMPLE: =>sntp list IP Address 100.101.110.111 100.101.110.112 100.101.110.113 => Version 4 4 4 Status Name contacting ... Unable to contact Synchronized DESCRIPTION: The status of an NTP server can be: > > > Not used: The Thomson ST SNTP client is disabled. As a consequence, none of the NTP servers are used. > Synchronized: The Thomson ST SNTP client was able to contact this NTP server.
PAGE 693
Software Commands 36 Software Commands Introduction This chapter describes the commands of the software command group. Contents This chapter covers the following commands: software upgrade Reboot the modem to initiate the SW upgrade. 672 software version Display the software version. 673 E-DOC-CTC-20061027-0003 v2.
PAGE 694
Software Commands software upgrade Reboot the modem to initiate the SW upgrade. New software available on a remote LAN host will be uploaded to the modem. SYNTAX: software upgrade 672 E-DOC-CTC-20061027-0003 v2.
PAGE 695
Software Commands software version Display the software version. SYNTAX: software version E-DOC-CTC-20061027-0003 v2.
PAGE 696
Software Commands 674 E-DOC-CTC-20061027-0003 v2.
PAGE 697
System Commands 37 System Commands Introduction This chapter describes the commands of the system command group. Contents This chapter covers the following commands: system config Set/change the system configuration parameters. 676 system flush Flush the current system configuration. 678 system locale Set/get the regional settings. 679 system reboot Reboot the Thomson ST. 681 system reset Reset the Thomson ST to its factory or ISP defaults and reboot the device.
PAGE 698
System Commands system config Set/change the system configuration parameters. ! For a good operation of UPnP and the discovery mechanism, it is highly recommended not to change the system configuration settings.
PAGE 699
System Commands autosavedelay A number between 0 and 600. Represents the autosave delay in seconds (0 for immediate save). OPTIONAL EXAMPLE: =>system config upnp discovery TR-64 discovery mdap discovery drst support reset button digest authentication rtc defaultconnection autosave autosave delay => E-DOC-CTC-20061027-0003 v2.
PAGE 700
System Commands system flush Flush the current system configuration. The system password and the system config settings (dcache excluded) are flushed. i The flush command does not impact previously saved configurations. SYNTAX: system flush EXAMPLE: =>system flush Security notification: Password changed, use 'saveall' to make it permanent. => 678 E-DOC-CTC-20061027-0003 v2.
PAGE 701
System Commands system locale Set/get the regional settings. SYNTAX: system locale [dec_symbol = <{, | .}>] [group_symbol = <{. | ,}>] [date_separator = <{/ | - | .}>] [date_format = <{iso | ddmmyyyy | ddmmyy | mmddyyyy | mmddyy}>] [time_format = <{iso | hmmss}>] [datetime_format = <{iso | date+time | time+date}>] [duration_format = <{dhmmss | hmmss}>] where: dec_symbol Set the decimal symbol. Choose between: > > OPTIONAL . , The default is “,”. group_symbol Set the group symbol.
PAGE 702
System Commands time_format Set the time format. Choose between: > > OPTIONAL iso hmmss. The default is iso. Note datetime_format h = hours; mm = minutes; ss = seconds. Set the date-time format. Choose between: > > > OPTIONAL iso date+time time+date. The default is date+time. duration_format Set the duration format. Choose between: > > OPTIONAL dhmmss hmmss. The default is dhmmss. Note d = days; h = hours; mm = minutes; ss = seconds.
PAGE 703
System Commands system reboot Reboot the Thomson ST. ! Non-saved configuration settings will be lost after reboot. SYNTAX: system reboot EXAMPLE: =>system reboot ..... (lost session connectivity due to reboot) ..... RELATED COMMANDS: system timedreboot E-DOC-CTC-20061027-0003 v2.0 Set or change a timed reboot for the Thomson ST..
PAGE 704
System Commands system reset Reset the Thomson ST to its factory or ISP defaults and reboot the device. ! All user specific settings and all saved configuration changes are lost after reboot. SYNTAX: system reset factory yes/no = <{yes | no}> proceed no/yes = <{no | yes}> where: factory yes/no Choose between: > > proceed no/yes REQUIRED yes: delete user and ISP specific settings. no: delete user specific settins only. Confirmation for resetting the modem.
PAGE 705
System Commands RELATED COMMANDS: sntp config E-DOC-CTC-20061027-0003 v2.0 Modify/display the SNTP client configuration.
PAGE 706
System Commands system timedreboot Set or change a timed reboot for the Thomson ST. SYNTAX timedreboot [state = <{disabled|enabled}>] [time = ] [date = ] where: state Enable/Disable timed reboot. The default is disabled. OPTIONAL time Change default countdown time (Min). A number between 0 and 16384. The default is 60. OPTIONAL date Set date/time to reboot (DD/MM/YYYY/HH:MM).
PAGE 707
System Commands system debug autosave Autosave debugging commands SYNTAX: system debug autosave [trace = <{disabled|enabled}>] where: trace E-DOC-CTC-20061027-0003 v2.
PAGE 708
System Commands system debug stats Show the Thomson ST CPU and memory statistics. SYNTAX: system debug stats [reset = <{disabled | enabled}>] where: reset Reset the CPU statistics. The default is disabled. OPTIONAL DESCRIPTION: > CHIP memory: Memory used by the CPU (first MB from the RAM) – not cached since it has to be realtime. > Application memory: Memory used by the applications. > min: The least amount of free memory detected during the uptime of the Thomson ST. 686 E-DOC-CTC-20061027-0003 v2.
PAGE 709
System Commands system ra config Configure Remote management access parameters. SYNTAX: system ra config [secure = <{disabled | enabled}>] [port = ] [timeout = ] where: secure Enable or disable https. The default is enabled. OPTIONAL port Set the destination port for remote access. The default is 51003. OPTIONAL timeout Set the connection timeout in minutes.
PAGE 710
System Commands system rtc synchronize Do a SNTP update and synchronize the realtime clock. SYNTAX: system rtc synchronize 688 E-DOC-CTC-20061027-0003 v2.
PAGE 711
System Commands system rtc settime Set/get date, time, timezone, daylight savings time, uptime. When synchronization with an external NTP server via the Thomson ST SNTP client fails, this command allows to manually configure its internal clock. i In cases without regular synchronization, accurate realtime clock settings can not be guaranteed.
PAGE 712
System Commands 690 E-DOC-CTC-20061027-0003 v2.
PAGE 713
Systemlog Commands 38 Systemlog Commands Introduction This chapter describes the commands of the systemlog command group. Contents This chapter covers the following commands: systemlog flush Flush all messages in the internal Syslog message buffer. 692 systemlog show Show messages in the internal Syslog message buffer. 693 systemlog send Send messages from the internal Syslog message buffer to a specified local or remote syslog server host. 695 E-DOC-CTC-20061027-0003 v2.
PAGE 714
Systemlog Commands systemlog flush Flush all messages in the internal Syslog message buffer. SYNTAX: systemlog flush 692 E-DOC-CTC-20061027-0003 v2.
PAGE 715
Systemlog Commands systemlog show Show messages in the internal Syslog message buffer. SYNTAX: systemlog show [fac = ] [sev = ] [hist = <{disabled | enabled}>] where: fac Specify the facility name of the syslog messages to be shown. Use one of the supported facility names (see “ Supported Facilities” on page 751). Note sev hist OPTIONAL If not specified, the messages of all the severities will be shown.
PAGE 716
Systemlog Commands EXAMPLE: =>syslog msgbuf show fac=kern sev=emerg hist=enabled <0> SysUpTime: 14:45:43 KERNEL Controlled restart (after internal error or explicit system re boot) <0> SysUpTime: 02:58:18 KERNEL Controlled restart (after internal error or explicit system re boot) <0> SysUpTime: 04 days 04:52:37 KERNEL Controlled restart (after internal error or explicit s ystem reboot) <0> SysUpTime: 00:00:41 KERNEL Controlled restart (after internal error or explicit system re boot) =>syslog msgbuf show f
PAGE 717
Systemlog Commands systemlog send Send messages from the internal Syslog message buffer to a specified local or remote syslog server host. i There will be no notification on whether the host has received the messages or not. SYNTAX: systemlog send [fac = ] [sev = ] [hist = <{disabled | enabled}>] dest = where: fac Specify the facility name of the syslog messages to show.
PAGE 718
Systemlog Commands systemlog DBG dbg_syslog Perform a syslog call. SYNTAX: systemlog DBG dbg_syslog priority = msgstring = where: 696 priority priority number msgstring message content E-DOC-CTC-20061027-0003 v2.
PAGE 719
Systemlog Commands systemlog DBG dbg_long_mess Generate a long syslog message call. SYNTAX: systemlog DBG dbg_long_mess E-DOC-CTC-20061027-0003 v2.
PAGE 720
Systemlog Commands systemlog DBG dbg_burst Perform a syslog message burst. SYNTAX: systemlog DBG dbg_burst 698 E-DOC-CTC-20061027-0003 v2.
PAGE 721
Systemlog Commands systemlog DBG dbg_contents Show the contents of the message buffer. SYNTAX: systemlog DBG dbg_contents E-DOC-CTC-20061027-0003 v2.
PAGE 722
Systemlog Commands 700 E-DOC-CTC-20061027-0003 v2.
PAGE 723
Upgrade Commands 39 Upgrade Commands Introduction This chapter describes the commands of the upgrade command group. Contents This chapter covers the following commands: upgrade config Change the upgrade daemon configuration. 702 upgrade start Start a new upgrade. 703 upgrade debug traceconfig Enable/disable upgrade daemon tracing. 704 upgrade debug sesslist Display the list of sessions. 705 upgrade profile add Add a new file profile description.
PAGE 724
Upgrade Commands upgrade config Change the upgrade daemon configuration. SYNTAX: upgrade config [state = <{disabled|enabled}>] [protocol = <{tftp|ftp|http|https}>] where: state Set the upgrade daemon state to enabled or disabled. OPTIONAL The default is disabled. protocol The transfer protocol to be used for file download. OPTIONAL Choose between: > > > > tftp ftp http https The default is tftp.
PAGE 725
Upgrade Commands upgrade start Start a new upgrade. SYNTAX: upgrade start protocol = <{tftp|ftp|http|https}> [server = ] [filename = ] where: protocol The protocol to be used for the download. REQUIRED Choose between: > > > > tftp ftp http https The default is disabled. server The server name or IP address OPTIONAL filename The file to be downloaded OPTIONAL E-DOC-CTC-20061027-0003 v2.
PAGE 726
Upgrade Commands upgrade debug traceconfig Enable/disable upgrade daemon tracing. SYNTAX: upgrade debug traceconfig state = <{disabled|enabled}> where: state 704 Set the upgared daemon state to enabled or disabled. REQUIRED E-DOC-CTC-20061027-0003 v2.
PAGE 727
Upgrade Commands upgrade debug sesslist Display the list of sessions. SYNTAX: upgrade debug sesslist EXAMPLE: =>:upgrade debug sesslist Session 0: --------------------------------------------------------------SessionId : 0x80c25850 State : IDLE Protocol : TFTP ServerName: FileName : DestFile : ServerIP : 0.0.0.0 Error : Session 1: --------------------------------------------------------------SessionId : 0x80c25c20 State : IDLE Protocol : TFTP ServerName: FileName : DestFile : ServerIP : 0.0.0.
PAGE 728
Upgrade Commands upgrade profile add Add a new file profile description. SYNTAX: upgrade profile add extension = <{sts|ini}> [maxsize(KBytes) = ] action = <{none|config_load|script_load|reboot}> where: extension The extension of the new file profile. Choose between: > > REQUIRED sts ini maxsize The maximum filesize (in KBytes) allowed for files with the extension of this profile. The default is 100.
PAGE 729
Upgrade Commands upgrade profile modify Modify a file profile description. SYNTAX: upgrade profile modify extension = <{sts|ini}> [maxsize(KBytes) = ] action = <{none|config_load|script_load|reboot}> where: extension The extension of the new file profile. Choose between: > > REQUIRED sts ini maxsize The maximum filesize (in KBytes) allowed for files with the extension of this profile. The default is 100.
PAGE 730
Upgrade Commands upgrade profile delete Delete a file profile description. SYNTAX: upgrade profile delete extension = <{sts|ini}> where: extension The extension of the profile to be deleted. Choose between: > > REQUIRED sts ini RELATED COMMANDS: 708 upgrade profile add Add a new file profile description. upgrade profile list Display a list of the file profile descriptions. E-DOC-CTC-20061027-0003 v2.
PAGE 731
Upgrade Commands upgrade profile list Display a list of the file profile descriptions. SYNTAX: upgrade profile list RELATED COMMANDS: upgrade profile delete Delete a file profile description. upgrade profile modify Modify a file profile description. E-DOC-CTC-20061027-0003 v2.
PAGE 732
Upgrade Commands upgrade ifadd Add a download interface. SYNTAX: upgrade ifadd intf = where: intf A download interface REQUIRED RELATED COMMANDS: 710 E-DOC-CTC-20061027-0003 v2.
PAGE 733
Upgrade Commands upgrade ifattach Attach a download interface. SYNTAX: upgrade ifattach intf = where: intf A download interface REQUIRED RELATED COMMANDS: E-DOC-CTC-20061027-0003 v2.
PAGE 734
Upgrade Commands upgrade ifconfig Configure a download interface.
PAGE 735
Upgrade Commands upgrade ifdelete Delete a download interface. SYNTAX: upgrade ifdelete intf = where: intf A download interface REQUIRED RELATED COMMANDS: E-DOC-CTC-20061027-0003 v2.
PAGE 736
Upgrade Commands upgrade ifdetach Detach a download interface. SYNTAX: upgrade ifdetach intf = where: intf A download interface REQUIRED RELATED COMMANDS: 714 E-DOC-CTC-20061027-0003 v2.
PAGE 737
Upgrade Commands upgrade iflist List all download interfaces. SYNTAX: upgrade iflist RELATED COMMANDS: E-DOC-CTC-20061027-0003 v2.
PAGE 738
Upgrade Commands 716 E-DOC-CTC-20061027-0003 v2.
PAGE 739
UPnP Commands 40 UPnP Commands Introduction This chapter describes the commands of the upnp command group. Contents This chapter covers the following commands: upnp config Configure the UPnP™ parameter(s). 718 upnp flush Flush the UPnP™ configuration. The UPnP configuration will be reset to the default configuration. 719 upnp list List all registered devices. 720 E-DOC-CTC-20061027-0003 v2.
PAGE 740
UPnP Commands upnp config Configure the UPnP™ parameter(s). SYNTAX: upnp config [maxage = ] [writemode = <{full | natonly | readonly}>] [safenat = <{disabled | enabled}>] [preferredaddress = ] [httpport = ] where: maxage A number between 60 and 999999. This parameter allows to configure how often the Thomson ST sends a notification message to advertise its presence as an Internet Gateway Device (IGD) on the network. The default is 1800.
PAGE 741
UPnP Commands upnp flush Flush the UPnP™ configuration. The UPnP configuration will be reset to the default configuration. SYNTAX: upnp flush E-DOC-CTC-20061027-0003 v2.
PAGE 742
UPnP Commands upnp list List all registered devices. i Use this command to check whether a PPP connection is properly configured and thus advertised as a PPP service. SYNTAX: upnp list [verbose = ] where: verbose Verbose level. The default is 1. OPTIONAL EXAMPLE: =>upnp list ---------------- device: IGD.xml -----------Advertised on: LocalNetwork (10.0.0.
PAGE 743
User Commands 41 User Commands Introduction This chapter describes the commands of the user command group. Contents This chapter covers the following commands: user add Add a user. 722 user config Modify a user. 724 user delete Delete a user. 726 user flush Flush the users. 727 user list Display the users. 728 user rights Display the session rights. 730 E-DOC-CTC-20061027-0003 v2.
PAGE 744
User Commands user add Add a user. i You can only add a user whose privileges are the same or lower than your own privileges. SYNTAX: user add name = password = role = [hash2 = ] [descr = ] [defuser = <{disabled | enabled}>] [defremadmin = <{disabled | enabled}>] [deflocadmin = <{disabled | enabled}>] where: name The new user name. Note REQUIRED 1. The maximum number of users is 10. 2. The maximum length is 32 characters.
PAGE 745
User Commands EXAMPLE: In the example below, the user Administrator creates a new user JohnDoe. This user has lower access rights than the user “Poweruser”. {Administrator}=>user list User Flags Role -------- ---Administrator U Administrator tech R TechnicalSupport {Administrator}[user]=>add name = JohnDoe password = **** Please retype password for verification.
PAGE 746
User Commands user config Modify a user. i You can only modify a user whose privileges are the same or lower than your own privileges. SYNTAX: user config name = [password = ] [role = ] [descr = ] [defuser = <{disabled | enabled}>] [defremadmin = <{disabled | enabled}>] [deflocadmin = <{disabled | enabled}>] where: name The user name. REQUIRED password The password. OPTIONAL Note role The role name.
PAGE 747
User Commands EXAMPLE: {Superuser}=>user list User ==== Superuser aPoweruser Role ==== root Poweruser {Superuser}=>user config name=aPoweruser role=LAN_admin {Superuser}=>user list User Role ==== ==== Superuser root aPoweruser LAN_admin {Superuser}=> E-DOC-CTC-20061027-0003 v2.
PAGE 748
User Commands user delete Delete a user. i You can only delete a user whose privileges are the same or lower than your own privileges. SYNTAX: user delete name = where: name The name of the user to be deleted.
PAGE 749
User Commands user flush Flush the users. After execution of this command, the access to the Thomson ST will no longer be protected by a password. The first user that logs on, after initiating a new Telnet session, will have the same administrative rights as a user with the role root.
PAGE 750
User Commands user list Display the users. SYNTAX: user list [name = ] [channel = <{ftp | telnet | http | mdap | serial}>] [origin = <{lan | wan | local}>] [secure = <{disabled | enabled}>] where: name The user name. Note channel telnet http mdap serial. wan local. OPTIONAL disabled enabled. Note 728 If not specified, all the origins will be listed. The selected security level. Choose between: > > OPTIONAL lan Note secure If not specified, all the channels will be listed.
PAGE 751
User Commands EXAMPLE: {Administrator}=>user list User ---Administrator tech Flags ----U R Role ---Administrator TechnicalSupport {Administrator}=>user list name=tech channel=http origin=wan service(s): r_lan, r_wan, r_fs_view, r_fs_retrieve, r_rtg, r_fwdg, r_nat, r_frwl, r_ipsec_norm, r_ipsec_adv, r_certificates, r_remote_mgnt, r_local, r_qos, w_lan, w_wan, w_fs_passive, w_rtg, w_fwdg, w_nat, w_frwl_norm, w_frwl_adv, w_frwe_mgnt, w_ipsec, w_certificates, w_remote_mgnt, w_local, w_qos, snd_lan, snd_wan,
PAGE 752
User Commands user rights Display the session rights. i The user rights of the currently logged-in user are shown.
PAGE 753
Abbreviations 42 Abbreviations The table below lists all the abbreviations used in the CLI Reference Guide.
PAGE 754
Abbreviations 732 Abbreviation Description HTTP HyperText Transfer Protocol ICMP Internet Control Message Protocol IDS Intrusion Detection System IGD Internet Gateway Device IGMP Internet Group Management Protocol IKE Internet Key Exchange IP Internet Protocol IP oA IP over ATM IPCP Internet Protocol Control Protocol IPSec IP Security ISDN Integrated Services Digital Network ISI Independent Set ID KB Kilobytes Kbps Kilobits per second LAN Local Area Network LCP Link Contro
PAGE 755
Abbreviations Abbreviation Description PPPoA PPP over ATM PPPoE PPP over Ethernet PPTP Point-to-Point Tunneling Protocol PSD Power Spectral Density PSK Pre-Shared Key PVC Permanent Virtual Channel QoS Quality of Service RIP Routing Information Protocol RTC Real Time Clock RTT Round Trip Time SAs Security Associations SFTP Secure File Transfer Protocol SHDSL Single Pair High-speed Digital Subscriber Line SIP Session Initiation Protocol SLA Service Level Agreement SMTP Simple
PAGE 756
Abbreviations 734 Abbreviation Description VLSM Variable Length Subnet Masking VP Virtual Path VPI Virtual Path Identifier VPN Virtual Private Networking WAN Wide Area Network WDS Wireless Distribution System WEP Wired Equivalent Privacy WFQ Weighted Fair Queueing WINS Windows Internet Naming Service WLAN Wireless LAN WPA Wi-Fi Protected Access WRR Weighted Round Robin E-DOC-CTC-20061027-0003 v2.
PAGE 757
System Logging Messages 43 System Logging Messages Introduction This chapter lists the different System Logging messages.
PAGE 758
System Logging Messages Auto-PVC Module Facility Severity Contents LOCAL5 WARNING AUTOPVC script failed LOCAL5 WARNING AUTOPVC script failed LOCAL5 WARNING AUTOPVC script (name1, qosb_name) failed LOCAL5 WARNING AUTOPVC script (name1, qosb_name, name2) failed LOCAL5 WARNING AUTOPVC script 'autopvc_change_qos (itable[i].
PAGE 759
System Logging Messages DHCP Relay Module Facility Severity Contents LOCAL2 WARNING DHCR relay: Dropping boot rqs on interface due to invalid giaddr for server () LOCAL2 WARNING DHCR relay: Dropping boot reply with invalid relay agent option from LOCAL2 WARNING DHCR relay: Dropping boot request containing the relay agent option from LOCAL2 WARNING DHCR relay: Dropping boot reply to unknown interface from LOCAL2 WARNING DHCR relay: Droppin
PAGE 760
System Logging Messages Dyndns Module Facility Severity Contents DYNDNS WARNING Connection failed to for client DYNDNS WARNING Failed to resolve host name for client DYNDNS WARNING Server Timeout() for client DYNDNS WARNING Update failed to server for client DYNDNS NOTICE clien
PAGE 761
System Logging Messages LOGIN Module Facility Severity Contents AUTH NOTICE LOGOUT User logged out on () AUTH NOTICE LOGOUT User logged out on AUTH NOTICE LOGOUT session of user killed () AUTH NOTICE LOGOUT session of user killed AUTH NOTICE LOGIN User tried to login on (from ) AUTH NOTICE LOGIN User logged in
PAGE 762
System Logging Messages PPP Module Facility Severity Contents LOCAL0 WARNING PPP Link up () LOCAL0 WARNING PPP Link down () AUTH ERROR PPP PAP authentication failed () [protocol reject] AUTH INFO PPP PAP on intf no response to authenticate-request AUTH NOTICE PPP PAP remote user successful authenticated AUTH ERROR PPP PAP authentication for remote user failed AUTH INFO PPP PAP Authenticate Ack received AUTH
PAGE 763
System Logging Messages RIP Module Facility Severity Contents LOCAL1 INFO RIP Packet received from unknown interface LOCAL1 INFO RIP Packet size is smaller than minimum size LOCAL1 INFO RIP Packet size is greater than maximum size LOCAL1 INFO RIP Wrong RIP packet alignment LOCAL1 INFO RIP RIP version 0 with command received LOCAL1 INFO RIP Reserved field not zero in RIP header LOCAL1 INFO RIP RIP is not enabled for network address LOCAL1 INFO RIP Packet
PAGE 764
System Logging Messages Facility Severity Contents LOCAL1 INFO RIP IP Address not found in RIP table Routing Module Facility Severity Contents LOCAL1 INFO GRP Default destination is routed via gateway LOCAL1 INFO GRP Default destination is not routed anymore via gateway SECURITY INFO LABEL Rule Id: Protocol: ICMP Src_ip: Dst_ip: ICMP message type: Label: SECURITY
PAGE 765
System Logging Messages Software Module Facility Severity Contents KERN INFO SOFTWARE File initiated KERN INFO SOFTWARE File <““ || not> successful terminated" UPnP Module Facility Severity Contents WARNING SECURITY UPnP refused for ip= NOTICE SECURITY UPnP () for ip= NOTICE SECURITY UPnP action from ip= () E-DOC-CTC-2006
PAGE 766
System Logging Messages 744 E-DOC-CTC-20061027-0003 v2.
PAGE 767
Supported Key Names 44 Supported Key Names Contents This chapter lists all the key names supported by the Thomson ST, that can be used for completing CLI command parameters: Supported IP Protocols 746 Supported TCP/UDP Port Names 747 Supported ICMP Type Names 750 Supported Facilities 751 Supported Severities 752 IP Precedence 752 Differentiated Services Code Point (DSCP) 753 E-DOC-CTC-20061027-0003 v2.
PAGE 768
Supported Key Names Supported IP Protocols For more information on the listed IP protocols, see RFC1340 or www.iana.org.
PAGE 769
Supported Key Names Supported TCP/UDP Port Names For more information on the listed TCP/UDP port assignments, see RFC1340 or www.iana.org.
PAGE 770
Supported Key Names 748 Port name Number TCP UDP Description sntp 123 Y Y Simple Network Time Protocol (SNTP) ingres-net 134 Y Y INGRES-NET Service netbios-ns 137 Y Y NETBIOS Naming System netbios-dgm 138 Y Y NETBIOS Datagram Service netbios-ssn 139 Y Y NETBIOS Session Service imap2 143 Y Y Internet Message Access Protocol (IMAP) v2 sql-net 150 Y Y SQL-NET pcmail-srv 158 Y Y PCMail Server snmp 161 Y Y Simple Network Management Protocol (SNMP) snmptrap 162
PAGE 771
Supported Key Names Port name Number TCP UDP Description ntalk 518 Y Y NTalk utime 519 Y Y UNIX Time rip 520 - Y Local routing process (on site); uses variant of Xerox NS Routing Information Protocol (RIP) timed 525 Y Y Timeserver netwall 533 Y Y For emergency broadcasts new-rwho 540 Y Y uucpd remote who is uucp 540 Y Y uucpd uucp-rlogin 540 Y Y uucpd remote login rtsp 554 Y Y Real Time Streaming Protocol (RTSP) whoami 565 Y Y whoami ipcserver 600 Y
PAGE 772
Supported Key Names Supported ICMP Type Names For more information on the listed ICMP type names, see RFC1340 or www.iana.org.
PAGE 773
Supported Key Names Supported Facilities For more information on the listed facilities, see RFC3164.
PAGE 774
Supported Key Names Supported Severities For more information on the listed severities, see RFC3164.
PAGE 775
Supported Key Names Differentiated Services Code Point (DSCP) For more information on DSCP, see RFC3260.
PAGE 776
Supported Key Names 754 E-DOC-CTC-20061027-0003 v2.
PAGE 777
Index A appinfo aal5stats applist connection appinfo 84 atm debug aal5stats 41 actlist connection applist 85 arpadd eth bridge dynvlan actlist 265 add ip arpadd 433 arpdelete atm bundle add 27 atm oam vclb add 52 atm phonebook add 55 atm qosbook add 60 dhcp client rqoptions add 122 dhcp client txoptions add 126 dhcp relay add 130 dhcp rule add 143 dhcp server lease add 155 dhcp server pool add 168 dns server host add 199 dns server route add 203 dsd urlfilter rule add 220 dyndns add 228 dyndns hos
PAGE 778
Index add 55 autolist 56 delete 57 flush 58 list 59 qosbook add 60 config 61 ctdadd 62 ctddelete 64 ctdlist 65 delete 66 flush 67 list 68 attach atm bundle attach 28 autolist atm phonebook autolist 56 autopvc config 70 info 72 autosave system debug autosave 685 B bind connection bind 86 bindlist connection bindlist 87 C capture eth switch mirror capture 307 clean connection clean 88 clear atm bundle clear 30 connection clear 89 dhcp client debug clear 119 dhcp server debug clear 151 dns server debug clea
PAGE 779
Index service host config 629 snmp config 650 sntp config 667 system config 676 system ra config 687 upgrade config 702 upnp config 718 user config 724 connection appconfig 82 appinfo 84 applist 85 bind 86 bindlist 87 clean 88 clear 89 config 90 debug 91 describe 92 flush 93 info 94 list 95 refresh 96 stats 97 timerclear 98 timerconfig 99 unbind 100 ctdadd atm qosbook ctdadd 62 ctddelete atm qosbook ctddelete 64 ctdlist atm qosbook ctdlist 65 cwmp config 102 server config 104 D debug connection debug 91 e
PAGE 780
Index optionlist 125 txoptions add 126 delete 127 list 128 relay add 130 config 133 debug stats 131 traceconfig 132 delete 134 flush 135 ifconfig 136 iflist 138 list 139 modify 140 ruleadd 141 ruledelete 142 rule add 143 debug traceconfig 144 delete 145 flush 146 list 147 server config 148 debug clear 151 stats 152 traceconfig 154 flush 149 lease add 155 delete 157 flush 158 list 159 option flush 160 instadd 161 instdelete 163 instlist 164 tmpladd 165 tmpldelete 166 tmpllist 167 policy 150 pool add 168 con
PAGE 781
Index delete 221 flush 222 list 223 modify 224 dump config dump 75 dyndns add 228 delete 229 flush 230 host add 234 delete 235 flush 236 list 237 list 231 modify 232 service list 238 modify 240 E egress eth switch mirror egress 308 env flush 244 get 245 list 246 set 247 unset 248 eth bridge add 261 clear 259 config 264 delete 262 dynvlan actlist 265 add 266 config 267 delete 268 flush 269 list 270 flush 271 ifadd 272 ifattach 273 ifconfig 274 ifdelete 276 ifdetach 277 ifflush 279 iflist 278 E-DOC-CTC-200
PAGE 782
Index iflist 322 vlan add 323 delete 324 flush 325 list 326 exec debug exec 106 mbus client exec 519 export mlp debug export 546 expr add 328 delete 332 flush 334 list 335 modify 339 F firewall chain add 349 delete 351 flush 353 list 354 config 344 debug clear 355 stats 356 traceconfig 357 flush 346 level add 358 delete 359 flush 360 list 361 modify 362 set 363 list 347 rule add 364 debug clear 370 stats 372 traceconfig 374 delete 365 flush 366 list 367 modify 369 760 flush atm bundle flush 33 atm flush
PAGE 783
Index G get env get 245 snmp get 651 snmp getnext 652 getaddress dns server debug spoof getaddress 195 getflags dns server debug spoof getflags 196 grouplist igmp proxy grouplist 420 grp config 376 flush 377 rip config 379 flush 382 ifconfig 383 show 385 rtlist 378 gstats atm debug gstats 42 H hostmgr add 388 clear 390 config 391 delete 392 flush 393 list 394 httpprobe ip debug httpprobe 467 I ids clear 396 config 397 list 398 parser config 399 pattern clear 401 E-DOC-CTC-20061027-0003 v2.
PAGE 784
Index atm ifdelete 24 dhcp client ifdelete 113 eth bridge ifdelete 276 eth bridge vlan ifdelete 299 eth ifdelete 255 ip auto ifdelete 464 ip ifdelete 443 ppp ifdelete 594 ppp relay ifdelete 607 service system ifdelete 640 snmp ifdelete 659 ifconfig 413 iflist 414 list 412 proxy config 417 debug clear 424 flush 419 grouplist 420 ifconfig 421 iflist 422 mbslist 423 ifdetach atm ifdetach 25 dhcp client ifdetach 114 eth bridge ifdetach 277 eth ifdetach 256 ip auto ifdetach 465 ip ifdetach 444 ppp ifdetach 59
PAGE 785
Index iflist 445 ifwait 446 ipadd 447 ipconfig 448 ipdelete 449 iplist 450 mcast flush 454 rtadd 451 rtdelete 452 rtlist 453 rtadd 455 rtdelete 457 rtlist 458 L label add 488 chain add 495 delete 496 flush 497 list 498 delete 489 flush 490 list 491 modify 492 rule add 499 debug clear 508 stats 510 traceconfig 511 delete 502 flush 504 list 505 modify 507 ipadd ip ipadd 447 service system ipadd 641 ipconfig ip ipconfig 448 ipdelete ip ipdelete 449 service system ipdelete 642 iplist language config 514 del
PAGE 786
Index eth switch qos list 316 eth switch share list 312 eth vlan list 326 expr list 335 firewall chain list 354 firewall level list 361 firewall list 347 firewall rule list 367 hostmgr list 394 ids list 398 ids pattern list 402 ids signature list 404 ids threshold list 407 igmp host list 412 interface list 428 ipqos ef list 479 ipqos list 477 ipqos queue list 484 label chain list 498 label list 491 label rule list 505 language list 516 mlp privilege list 555 mlp role list 563 pptp list 614 script list 623
PAGE 787
Index list 555 removezone 557 role add 558 addpriv 560 config 561 delete 562 list 563 removepriv 564 O optadd dhcp server pool optadd 175 optdelete dhcp server pool optdelete 176 optionlist dhcp client rqoptions optionlist 125 modify atm oam cc modify 50 atm oam modify 46 dhcp relay modify 140 dsd urlfilter rule modify 224 dyndns modify 232 dyndns service modify 240 expr modify 339 firewall level modify 362 firewall rule modify 369 ids signature modify 405 ids threshold modify 408 label modify 492 label
PAGE 788
Index profdelete ruledelete pptp profdelete 617 dhcp relay ruledelete 142 dhcp server pool ruledelete 181 proflist pptp proflist 618 run script run 625 proxy dsd debug proxy 213 S R save reboot system reboot 681 recycling dsd debug recycling 214 refresh connection refresh 96 register mbus client register 521 removepriv mlp role removepriv 564 removezone mlp privilege removezone 557 reset system reset 682 rights user rights 730 root commands ping 4 traceroute 5 rtadd dhcp server pool rtadd 178 ip m
PAGE 789
Index set env set 247 firewall level set 363 service host stats 635 system debug stats 686 synchronize settime system rtc settime 689 system rtc synchronize 688 Syslog messages show Auto-PVC 736 Configuration 736 DHCP client 736 DHCP relay 737 DHCP server 737 Dyndns 738 Firewall 738 Kernel 739 Linestate 739 LOGIN 739 NAPT 739 PPP 740 PPTP 740 RIP 741 Routing 742 Session 742 SNTP 742 Software 743 UPnP 743 grp rip show 385 systemlog show 693 snmp community add 654 delete 655 list 656 modify 657 config
PAGE 790
Index nat tmpladd 576 update tmpldelete dhcp server option tmpldelete 166 nat tmpldelete 580 dns server debug spoof update 198 upgrade config 702 debug sesslist 705 traceconfig 704 profile add 706 delete 708 modify 707 software upgrade 672 start 703 tmplinst nat tmplinst 582 tmpllist dhcp server option tmpllist 167 nat tmpllist 581 traceconfig dhcp client debug traceconfig 121 dhcp relay debug traceconfig 132 dhcp rule debug traceconfig 144 dhcp server debug traceconfig 154 firewall debug traceconfig 3
PAGE 791