Thomson TG576 v7 and TG585 v7 Residential DSL Gateway CLI Reference Guide R7.
Thomson TG576 v7 and TG585 v7 CLI Reference Guide R7.
Copyright Copyright ©1999-2007 THOMSON. All rights reserved. Distribution and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document.
Contents Contents: ? Command.................................................................................................. 25 .. Command.................................................................................................. 27 atm Commands............................................................................................29 atm cac config.....................................................................................................................................
Contents atm qosbook config............................................................................................................................ 60 atm qosbook ctdadd........................................................................................................................... 61 atm qosbook ctddelete....................................................................................................................... 62 atm qosbook ctdlist.................................................
Contents connection unbind.............................................................................................................................. 97 cwmp Commands........................................................................................99 cwmp config...................................................................................................................................... 100 cwmp debug traceconfig...............................................................................
Contents dhcp relay list.................................................................................................................................... 138 dhcp relay modify............................................................................................................................. 139 dhcp relay ruleadd............................................................................................................................ 140 dhcp relay ruledelete....................................
Contents dhcp server pool ruleadd................................................................................................................. 176 dhcp server pool ruledelete............................................................................................................. 177 dhcp spoofing add............................................................................................................................ 178 dhcp spoofing attach......................................................
Contents dsd Commands.......................................................................................... 213 dsd config.......................................................................................................................................... 214 dsd debug config.............................................................................................................................. 215 dsd debug connection list.......................................................................
Contents eth Commands...........................................................................................247 eth bridge add................................................................................................................................... 251 eth bridge clear................................................................................................................................. 252 eth bridge config...............................................................................
Contents eth bridge vlan ifadd........................................................................................................................ 288 eth bridge vlan ifconfig.................................................................................................................... 289 eth bridge vlan ifdelete.................................................................................................................... 290 eth bridge vlan iflist.............................................
Contents eth vlan add.......................................................................................................................................325 eth vlan delete...................................................................................................................................326 eth vlan flush.....................................................................................................................................327 eth vlan list......................................
Contents grp config...........................................................................................................................................366 grp flush............................................................................................................................................. 367 grp rip config.....................................................................................................................................368 grp rip flush...............................
Contents igmp host ifconfig............................................................................................................................. 402 igmp host iflist.................................................................................................................................. 403 igmp host list.....................................................................................................................................404 igmp proxy config....................................
Contents ip iflist.................................................................................................................................................440 ip ifwait...............................................................................................................................................441 ip ipadd.............................................................................................................................................. 442 ip ipconfig.......................
Contents label rule flush...................................................................................................................................475 label rule list...................................................................................................................................... 476 label rule modify............................................................................................................................... 477 language Commands...............................
Contents menu Command........................................................................................ 513 mlp Commands..........................................................................................515 mlp debug export..............................................................................................................................516 mlp debug stats................................................................................................................................
Contents ppp flush............................................................................................................................................ 550 ppp ifadd............................................................................................................................................ 551 ppp ifattach........................................................................................................................................ 552 ppp ifconfig..............................
Contents script run............................................................................................................................................ 588 service Commands.................................................................................... 589 service host add................................................................................................................................ 590 service host assign..........................................................................
Contents sntp Commands.........................................................................................627 sntp add............................................................................................................................................. 628 sntp config......................................................................................................................................... 629 sntp debug traceconfig....................................................................
Contents tls https-server cert delete............................................................................................................... 663 tls https-server cert list.....................................................................................................................664 tls https-server config....................................................................................................................... 665 tls self cert list...............................................
Contents wireless macacl flush........................................................................................................................699 wireless macacl list........................................................................................................................... 700 wireless macacl modify.................................................................................................................... 701 wireless macacl register...........................................
Contents xdsl debug traceconfig..................................................................................................................... 736 xdsl info..............................................................................................................................................737 xdsl version........................................................................................................................................738 24 E-DOC-CTC-20071119-0014 v1.
? Command ? Command Displays this help information E-DOC-CTC-20071119-0014 v1.
.. Command 26 E-DOC-CTC-20071119-0014 v1.
.. Command .. Command Exits group selection. E-DOC-CTC-20071119-0014 v1.
atm Commands 28 E-DOC-CTC-20071119-0014 v1.
atm Commands atm Commands atm cac config Configure ATM connection admission control. see page 31 atm cac list List all CAC parameters. see page 32 atm cac overbooking Configure ATM overbooking parameters. see page 33 atm debug aal5stats Display AAL5 port specific atm statistics. see page 34 atm debug gstats Display ATM global statistics. see page 35 atm debug portstats Display port specific atm statistics. see page 36 atm flush Flush all ATM interfaces.
atm Commands atm phonebook delete Delete a phonebook entry. see page 56 atm phonebook flush Flush all phonebook entries. see page 57 atm phonebook list Display the phonebook. see page 58 atm qosbook add Add a new qosbook entry. see page 59 atm qosbook config Modify the qosbook configuration. see page 60 atm qosbook ctdadd Add a new connection traffic descriptor. see page 61 atm qosbook ctddelete Delete a connection traffic descriptor.
atm Commands atm cac config Configure ATM connection admission control. SYNTAX: atm cac config port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number> state = <{disabled|enabled}> where: port The port for which CAC is configured. REQUIRED state Enable/disable CAC for an ATM port. REQUIRED E-DOC-CTC-20071119-0014 v1.
atm Commands atm cac list List all CAC parameters. 32 E-DOC-CTC-20071119-0014 v1.
atm Commands atm cac overbooking Configure ATM overbooking parameters. SYNTAX: atm cac overbooking [rt = [nrt = where: rt The realtime overbooking percentage. OPTIONAL nrt The non-realtime overbooking percentage. OPTIONAL E-DOC-CTC-20071119-0014 v1.
atm Commands atm debug aal5stats Display AAL5 port specific atm statistics. SYNTAX: atm debug aal5stats port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number> vpi = [vci = [clear = <{disabled|enabled}]> where: port The port number for which statistics will be retrieved. REQUIRED vpi The VPI number for which statistics will be retrieved. REQUIRED vci The VCI number for which statistics will be retrieved. OPTIONAL clear Clear the statistics after request.
atm Commands atm debug gstats Display ATM global statistics. SYNTAX: atm debug gstats [clear = <{disabled|enabled}]> where: clear E-DOC-CTC-20071119-0014 v1.0 Clear the statistics after request.
atm Commands atm debug portstats Display port specific atm statistics. SYNTAX: atm debug portstats port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number> [clear = <{disabled|enabled}]> where: port The port for which statistics will be retrieved. REQUIRED clear Clear the statistics after the request. OPTIONAL 36 E-DOC-CTC-20071119-0014 v1.
atm Commands atm flush Flush all ATM interfaces. E-DOC-CTC-20071119-0014 v1.
atm Commands atm ifadd Create a new ATM interface. SYNTAX: atm ifadd intf = where: intf 38 The name for the new ATM interface. If not specified, the destination will double as interface name. REQUIRED E-DOC-CTC-20071119-0014 v1.
atm Commands atm ifattach Attach an ATM interface. SYNTAX: atm ifattach intf = <{}> where: intf E-DOC-CTC-20071119-0014 v1.0 The name of the ATM interface.
atm Commands atm ifconfig Modify an ATM interface. SYNTAX: atm ifconfig intf = <{atm_Internet}> [dest = <{}]> [qos = <{default}]> [clp = <{0|1|classification}]> [clpthresh = [encaps = <{llc|vcmux}]> [fcs = <{disabled|enabled|auto}]> [ulp = <{mac|ip|ppp}]> [retry = where: intf The name of the ATM interface to configure. REQUIRED dest The WAN destination for this ATM interface. Typically, a phonebook entry.
atm Commands atm ifdelete Delete an ATM interface. SYNTAX: atm ifdelete intf = <{}> where: intf E-DOC-CTC-20071119-0014 v1.0 The name of the ATM interface.
atm Commands atm ifdetach Detach an ATM interface. SYNTAX: atm ifdetach intf = <{}> where: intf 42 The name of the ATM interface. REQUIRED E-DOC-CTC-20071119-0014 v1.
atm Commands atm iflist Display the ATM interfaces. SYNTAX: atm iflist [intf = <{atm_Internet}]> where: intf E-DOC-CTC-20071119-0014 v1.0 The name of an ATM interface.
atm Commands atm oam cc list Display CC configuration. 44 E-DOC-CTC-20071119-0014 v1.
atm Commands atm oam cc modify Modify CC on the connection. SYNTAX: atm oam cc modify port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number> vpi = [vci = [transmit = <{disabled|enabled}]> [receive = <{disabled|enabled}]> [auto = <{disabled|enabled}]> [span = <{segment|end2end}]> where: port The ATM port number. REQUIRED vpi The Virtual Path Identifier. REQUIRED vci The Virtual Channel Identifier. OPTIONAL transmit Enable/disable transmission of CC cells.
atm Commands atm oam cc send Send CC activate/deactivate to connection. SYNTAX: atm oam cc send port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number> vpi = [vci = [span = <{segment|end2end}]> [action = <{activate|deactivate}]> [direction = <{source|sink|both}]> where: port The ATM port number. REQUIRED vpi The Virtual Path Identifier. REQUIRED vci The Virtual Channel Identifier. OPTIONAL span Send CC action end2end or segment. OPTIONAL action The CC action.
atm Commands atm oam config Modify the ATM OAM settings. SYNTAX: atm oam config [clp = [loopbackid = where: clp The CLP bit value of the OAM cells. OPTIONAL loopbackid The loopback id (hexadecimal string) for processing of segment loopback cells. OPTIONAL E-DOC-CTC-20071119-0014 v1.
atm Commands atm oam list Display the ATM OAM settings. 48 E-DOC-CTC-20071119-0014 v1.
atm Commands atm oam modify Modify the ATM OAM data blocking mode. SYNTAX: atm oam modify port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number> blocking = <{disabled|enabled}> where: port The port for which OAM blocking is configured. REQUIRED blocking Enable/disable OAM blocking. REQUIRED E-DOC-CTC-20071119-0014 v1.
atm Commands atm oam ping Send ATM loopback cells. SYNTAX: atm oam ping dest = <{atm_pvc_8_35}> [count = [interval = where: dest The destination address for the request. REQUIRED count The number of pings to send. OPTIONAL interval The interval in milliseconds between packets. OPTIONAL 50 E-DOC-CTC-20071119-0014 v1.
atm Commands atm oam vclb add Create a loopback connection for VC SYNTAX: atm oam vclb add port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number> vpi = [vci = where: port The ATM port number. REQUIRED vpi The Virtual Path Identifier. REQUIRED vci The Virtual Channel Identifier. OPTIONAL E-DOC-CTC-20071119-0014 v1.
atm Commands atm oam vclb del Delete a loopback connection for VC SYNTAX: atm oam vclb del port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number> vpi = [vci = where: port The ATM port number. REQUIRED vpi The Virtual Path Identifier. REQUIRED vci The Virtual Channel Identifier. OPTIONAL 52 E-DOC-CTC-20071119-0014 v1.
atm Commands atm oam vclb list List all VC loopback connections E-DOC-CTC-20071119-0014 v1.
atm Commands atm phonebook add Add a new phonebook entry. SYNTAX: atm phonebook add name = addr = where: name The phonebook name for this destination. REQUIRED addr The address for this destination. REQUIRED 54 E-DOC-CTC-20071119-0014 v1.
atm Commands atm phonebook autolist Display auto PVC's. E-DOC-CTC-20071119-0014 v1.
atm Commands atm phonebook delete Delete a phonebook entry. SYNTAX: atm phonebook delete name = <{}> where: name 56 The name of the entry to delete. REQUIRED E-DOC-CTC-20071119-0014 v1.
atm Commands atm phonebook flush Flush all phonebook entries. E-DOC-CTC-20071119-0014 v1.
atm Commands atm phonebook list Display the phonebook. 58 E-DOC-CTC-20071119-0014 v1.
atm Commands atm qosbook add Add a new qosbook entry. SYNTAX: atm qosbook add name = [txctd = <{default}]> [rxctd = <{default}]> where: name The name for the new QoS entry. REQUIRED txctd The name of the CTD for transmit (upstream) direction. OPTIONAL rxctd The name of the CTD for receive (downstream) direction. OPTIONAL E-DOC-CTC-20071119-0014 v1.
atm Commands atm qosbook config Modify the qosbook configuration. SYNTAX: atm qosbook config [format = <{bytes|cells}]> where: format 60 The input, output format of the qosbook. OPTIONAL E-DOC-CTC-20071119-0014 v1.
atm Commands atm qosbook ctdadd Add a new connection traffic descriptor. SYNTAX: atm qosbook ctdadd name = conformance = <{UBR|CBR|VBR|UBR.1|UBR.2| UBR.mdcr|CBR.1|VBR.1|VBR.2|VBR.3|VBR.c|VBR.nt| VBR.t|GFR.1|GFR.
atm Commands atm qosbook ctddelete Delete a connection traffic descriptor. SYNTAX: atm qosbook ctddelete name = <{default}> [force = <{disabled|enabled}]> where: name The name of the CTD entry to delete. REQUIRED force Force delete even when the entry is still in use. OPTIONAL 62 E-DOC-CTC-20071119-0014 v1.
atm Commands atm qosbook ctdlist Display all connection traffic descriptors. E-DOC-CTC-20071119-0014 v1.
atm Commands atm qosbook delete Delete a qosbook entry. SYNTAX: atm qosbook delete name = <{default}> [force = <{disabled|enabled}]> where: name The name of the qosbook entry to delete. REQUIRED force Force delete even when the entry is still in use. OPTIONAL 64 E-DOC-CTC-20071119-0014 v1.
atm Commands atm qosbook flush Flush all qosbook entries. E-DOC-CTC-20071119-0014 v1.
atm Commands atm qosbook list Display the qosbook. 66 E-DOC-CTC-20071119-0014 v1.
autopvc Commands autopvc Commands autopvc config Configure autopvc. see page 68 autopvc list Show retreived information. see page 69 E-DOC-CTC-20071119-0014 v1.
autopvc Commands autopvc config Configure autopvc. SYNTAX: autopvc config [mode = <{pseudo|passive|active}]> [type = <{bridge|pppoerelay|ipoa|ethoa|pppoa| pppoe}]> [overwrite = <{disabled|enabled}]> [peakrate = where: mode Autopvc mode. OPTIONAL type Type of autopvc. OPTIONAL overwrite Enable/disable UBR peak rate overwrite. OPTIONAL peakrate The UBR peak rate (in kilobits per second) '0' to indicate linerate. OPTIONAL 68 E-DOC-CTC-20071119-0014 v1.
autopvc Commands autopvc list Show retreived information. SYNTAX: autopvc list [table = <{Port|AtmLayer|Vpc|Vcc|Address| AddressRegistrationAdmin|AAL5Profile| AAL2CommonProfile|AAL2TrunkingProfile| AAL2LESProfile|AtmServiceConnInfoExtension| AtmServiceTypeExtension| AAL5ProfileExtension}]> where: table E-DOC-CTC-20071119-0014 v1.0 Autopvc table.
config Commands 70 E-DOC-CTC-20071119-0014 v1.
config Commands config Commands config delete Delete a user configuration file. see page 72 config dump Show the saved configuration file see page 73 config flush Flush the loaded configuration. see page 74 config list Show the current configuration set see page 75 config load Load saved or default configuration. see page 76 config save Store current configuration to backup file see page 77 E-DOC-CTC-20071119-0014 v1.
config Commands config delete Delete a user configuration file. SYNTAX: config delete [filename = where: filename 72 configuration file to erase OPTIONAL E-DOC-CTC-20071119-0014 v1.
config Commands config dump Show the saved configuration file E-DOC-CTC-20071119-0014 v1.
config Commands config flush Flush the loaded configuration. SYNTAX: config flush [flush_ip = <{enabled|disabled}]> where: flush_ip 74 Flush IP settings or not. OPTIONAL E-DOC-CTC-20071119-0014 v1.
config Commands config list Show the current configuration set SYNTAX: config list [templates = <{disabled|enabled}]> where: templates E-DOC-CTC-20071119-0014 v1.
config Commands config load Load saved or default configuration. SYNTAX: config load [load_ip = <{enabled|disabled}]> [defaults = <{disabled|enabled}]> [flush = <{enabled|disabled}]> [echo = <{disabled|enabled}]> [filename = where: load_ip Load IP settings or not. OPTIONAL defaults Load default instead of saved configuration. OPTIONAL flush Flush current configuration before loading new one. OPTIONAL echo Echo each command string when loaded.
config Commands config save Store current configuration to backup file SYNTAX: config save filename = where: filename E-DOC-CTC-20071119-0014 v1.
connection Commands 78 E-DOC-CTC-20071119-0014 v1.
connection Commands connection Commands connection appconfig Modify a CONN/NAT application helper configuration see page 80 connection appinfo Display CONN/NAT application specific info see page 81 connection applist Display the available CONN/NAT application helpers. see page 82 connection bind Create a CONN/NAT application helper/port binding. see page 83 connection bindlist Display the CONN/NAT application helper/port bindings.
connection Commands connection appconfig Modify a CONN/NAT application helper configuration SYNTAX: connection appconfig application = <{IP6TO4|PPTP|ESP|IKE|SIP| JABBER|CU/SeeMe|RAUDIO(PNA)|RTSP|ILS|H245| H323|IRC|GAME(UDP)|CONE(UDP)|LOOSE(UDP)|FTP}> [trace = <{disabled|enabled}]> [timeout = [childqos = <{DSCP|Interactive|Management| Video|VoIP-RTP|VoIP-Signal|default}]> [floating = <{disabled|enabled}]> [proxy = <{disabled|enabled}]> [tracelevel = [SIP_ALG = <{disabled|e
connection Commands connection appinfo Display CONN/NAT application specific info SYNTAX: connection appinfo application = <{IP6TO4|PPTP|ESP|IKE|SIP| JABBER|CU/SeeMe|RAUDIO(PNA)|RTSP|ILS|H245| H323|IRC|GAME(UDP)|CONE(UDP)|LOOSE(UDP)|FTP}> where: application E-DOC-CTC-20071119-0014 v1.0 The name of a CONN/NAT application helper as listed by ':connection applist'.
connection Commands connection applist Display the available CONN/NAT application helpers. 82 E-DOC-CTC-20071119-0014 v1.
connection Commands connection bind Create a CONN/NAT application helper/port binding. SYNTAX: connection bind application = <{IP6TO4|PPTP|ESP|IKE|SIP| JABBER|CU/SeeMe|RAUDIO(PNA)|RTSP|ILS|H245| H323|IRC|GAME(UDP)|CONE(UDP)|LOOSE(UDP)|FTP}> port = where: application The name of a CONN/NAT application helper as listed by ':connection applist'. REQUIRED port The port number or range this application handler should work on. REQUIRED E-DOC-CTC-20071119-0014 v1.
connection Commands connection bindlist Display the CONN/NAT application helper/port bindings. 84 E-DOC-CTC-20071119-0014 v1.
connection Commands connection clean Clean connection database by forcing timeouts. SYNTAX: connection clean [level = where: level E-DOC-CTC-20071119-0014 v1.0 Scrubbing level.
connection Commands connection clear Kill all connections. 86 E-DOC-CTC-20071119-0014 v1.
connection Commands connection config Modify global connection configuration. SYNTAX: connection config [configchangemode = <{immediate|delayed}]> [probes = <{disabled|enabled}]> [udptrackmode = <{strict|loose}]> where: configchangemode Select how config changes are handled. OPTIONAL probes Enable/disable alive probes on idle connections. OPTIONAL udptrackmode UDP connection tracking mode. OPTIONAL E-DOC-CTC-20071119-0014 v1.
connection Commands connection debug Connection debug commands. SYNTAX: connection debug [trace = <{disabled|enabled}]> where: trace 88 Enable/disable traces. OPTIONAL E-DOC-CTC-20071119-0014 v1.
connection Commands connection describe Describe the streams of a connection. SYNTAX: connection describe [id = where: id E-DOC-CTC-20071119-0014 v1.0 The connection ID to describe.
connection Commands connection flush Flush the connection configuration. 90 E-DOC-CTC-20071119-0014 v1.
connection Commands connection info Display all modules with some info. E-DOC-CTC-20071119-0014 v1.
connection Commands connection list Display the currently known connections. SYNTAX: connection list [nr = [history = <{disabled|enabled}]> where: nr The number of connections to display. OPTIONAL history If enabled, show history. OPTIONAL 92 E-DOC-CTC-20071119-0014 v1.
connection Commands connection refresh Invalidate all cached decisions. E-DOC-CTC-20071119-0014 v1.
connection Commands connection stats Display connection and stream statistics. 94 E-DOC-CTC-20071119-0014 v1.
connection Commands connection timerclear Clear connection timeout to default. SYNTAX: connection timerclear [timer = <{tcpidle|tcpneg|tcpkill|udpidle| udpkill|icmpkill|ipidle|ipkill|aiprefresh}]> where: timer E-DOC-CTC-20071119-0014 v1.0 The name of the connection idle timer.
connection Commands connection timerconfig Modify connection timeout handling. SYNTAX: connection timerconfig [timer = <{tcpidle|tcpneg|tcpkill|udpidle| udpkill|icmpkill|ipidle|ipkill|aiprefresh}]> [value = where: timer The name of the connection idle timer. OPTIONAL value The timer expire value in seconds. OPTIONAL 96 E-DOC-CTC-20071119-0014 v1.
connection Commands connection unbind Delete a CONN/NAT application helper/port binding. SYNTAX: connection unbind application = <{IP6TO4|PPTP|ESP|IKE|SIP| JABBER|CU/SeeMe|RAUDIO(PNA)|RTSP|ILS|H245| H323|IRC|GAME(UDP)|CONE(UDP)|LOOSE(UDP)|FTP}> port = where: application The name of a CONN/NAT application helper as listed by ':connection applist'. REQUIRED port The port number or range this application handler should work on. REQUIRED E-DOC-CTC-20071119-0014 v1.
cwmp Commands 98 E-DOC-CTC-20071119-0014 v1.
cwmp Commands cwmp Commands cwmp config Configure the cwmpd as seen from the ACS. see page 100 cwmp debug traceconfig Enable or disable tracing. see page 102 cwmp server config Configure the cwmpd towards the ACS. see page 103 E-DOC-CTC-20071119-0014 v1.
cwmp Commands cwmp config Configure the cwmpd as seen from the ACS.
cwmp Commands connectionReqAuth Set the authentication type of modem CWMP server for asynchronous connects. OPTIONAL qos-class Set the quality of service class for outgoing CWMP data. OPTIONAL bootdelayrange Set the delay on boot before inform is sent. OPTIONAL upgradedelay Set whether to delay upgrade if services are active. OPTIONAL am1Termination Set if am 1 session termination is enabled. OPTIONAL persistentSubscription The cwmp daemon has persistent subscriptions.
cwmp Commands cwmp debug traceconfig Enable or disable tracing. SYNTAX: cwmp debug traceconfig [level = where: level 102 Set the tracelevel (0-1) OPTIONAL E-DOC-CTC-20071119-0014 v1.
cwmp Commands cwmp server config Configure the cwmpd towards the ACS. SYNTAX: cwmp server config [url = [username = [password = where: url Set the HTTP URL used to contact the ACS server. OPTIONAL username Set the username for ACS Digest Authentication. OPTIONAL password Set the password for ACS Digest Authentication. OPTIONAL E-DOC-CTC-20071119-0014 v1.
debug Command 104 E-DOC-CTC-20071119-0014 v1.
debug Command debug Command Execute a 'Trace & Debug' command. For qualified personnel only. SYNTAX: debug exec cmd = where: cmd E-DOC-CTC-20071119-0014 v1.
dhcp Commands 106 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp Commands dhcp client debug clear Clear DHCP client statistics see page 111 dhcp client debug stats Print DHCP client statistics see page 112 dhcp client debug traceconfig Modify DHCP client trace configuration see page 113 dhcp client flush Delete all DHCP clients. see page 114 dhcp client ifadd Create a DHCP client. see page 115 dhcp client ifattach Activate a DHCP client. see page 116 dhcp client ifconfig Configure a DHCP client.
dhcp Commands dhcp relay delete Delete an entry from the DHCP forward list. see page 134 dhcp relay flush Flushes the DHCP relay settings. see page 135 dhcp relay ifconfig Configure a relay interface. see page 136 dhcp relay iflist Show the configuration of the relay interfaces. see page 137 dhcp relay list List the DHCP forward list. see page 138 dhcp relay modify Modify an entry from the DHCP forward list.
dhcp Commands dhcp server option instlist List all DHCP server option instances see page 159 dhcp server option ruleadd Add a selection rule to a DHCP server option instance see page 160 dhcp server option ruledelete Delete a selection rule from a DHCP server option instance see page 161 dhcp server option tmpladd Add a DHCP server option template see page 162 dhcp server option tmpldelete Delete a DHCP server option template see page 163 dhcp server option tmpllist List all DHCP server opt
dhcp Commands dhcp spoofing list List the available SpoofingAssociations see page 185 dhcp spoofing option-add Add a DHCP Option Code to a Spoofing-Association. see page 186 dhcp spoofing option-delete Delete a DHCP Option Code from a Spoofing-Association. see page 187 110 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp client debug clear Clear DHCP client statistics E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp client debug stats Print DHCP client statistics 112 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp client debug traceconfig Modify DHCP client trace configuration SYNTAX: dhcp client debug traceconfig [state = <{disabled|enabled}]> where: state E-DOC-CTC-20071119-0014 v1.0 Enable/Disable tracing.
dhcp Commands dhcp client flush Delete all DHCP clients. 114 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp client ifadd Create a DHCP client. SYNTAX: dhcp client ifadd intf = <{Internet|LocalNetwork}> where: intf E-DOC-CTC-20071119-0014 v1.0 The name of the interface on which a DHCP Client is defined.
dhcp Commands dhcp client ifattach Activate a DHCP client. SYNTAX: dhcp client ifattach intf = <> where: intf 116 The name of the interface on which a DHCP Client is defined. REQUIRED E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp client ifconfig Configure a DHCP client. SYNTAX: dhcp client ifconfig intf = <> [label = <{None|DSCP|Interactive|Management| Video|VoIP-RTP|VoIP-Signal|default}]> [metric = [dnsmetric = [broadcast = <{disabled|enabled}]> [serverroute = <{disabled|enabled}]> [followlabel = <{disabled|enabled}]> where: intf The name of the dynamic interface to be configured. REQUIRED label Label for default gateway and static routes.
dhcp Commands dhcp client ifdelete Delete a DHCP client. SYNTAX: dhcp client ifdelete intf = <> where: intf 118 The name of the interface on which a DHCP Client is defined. REQUIRED E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp client ifdetach De-activate a DHCP client and releases its lease. SYNTAX: dhcp client ifdetach intf = <> where: intf E-DOC-CTC-20071119-0014 v1.0 The name of the interface on which a DHCP Client is defined.
dhcp Commands dhcp client iflist List DHCP clients. SYNTAX: dhcp client iflist [intf = <]> [expand = <{disabled|enabled}]> where: intf The name of the interface on which a DHCP Client is defined. OPTIONAL expand Expand enabled/disabled. OPTIONAL 120 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp client ifrenew Renew a DHCP lease. SYNTAX: dhcp client ifrenew intf = <> where: intf E-DOC-CTC-20071119-0014 v1.0 The name of the interface on which a DHCP Client is defined.
dhcp Commands dhcp client rqoptions add Add a DHCP Option Code to the Parameter Request List.
dhcp Commands dhcp client rqoptions delete Delete a DHCP Option Code from the Parameter Request List.
dhcp Commands dhcp client rqoptions list List all DHCP Option Codes in the Parameter Request List. SYNTAX: dhcp client rqoptions list [intf = <]> where: intf 124 The name of the interface on which a DHCP Client is defined. OPTIONAL E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp client rqoptions optionlist List all DHCP Option Codes that can be used in the Parameter Request List. E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp client txoptions add Add an option. SYNTAX: dhcp client txoptions add intf = <> option = <{subnet-mask|time-offset|defaultrouters|time-servers|ien116-name-impressservers|resource-location-servers|hostname|boot-file-size|merit-dump|domain-name| swap-server|root-path|extensions-path|ipforwarding|non-local-source-routing|policyfilter|max-dgram-reassembly|default-ip-ttl| path-mtu-aging-timeout|path-mtu-plateau-table| interface-mtu|all-subnets-local|broadcastaddress|perform-mask-discovery|..
dhcp Commands dhcp client txoptions delete Delete an option.
dhcp Commands dhcp client txoptions list List all options. SYNTAX: dhcp client txoptions list [intf = <]> [expand = <{disabled|enabled}]> where: intf The name of the interface on which a DHCP Client is defined. OPTIONAL expand Expand enabled/disabled. OPTIONAL 128 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp client txoptions optionlist Lists all DHCP Option Codes that can be used. E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp relay add Add an entry to the DHCP forward list. SYNTAX: dhcp relay add name = where: name 130 The forward entry name. REQUIRED E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp relay config Sets the relay configuration settings. SYNTAX: dhcp relay config [agentinfo = <{disabled|enabled}]> [agentmismatch = <{disabled|enabled}]> where: agentinfo Set the relay agent info status (RFC3046). OPTIONAL agentmismatch Forward/Drop DHCP reply packet when a relay agent info mismatch is detected (RFC3046). OPTIONAL E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp relay debug stats Print DHCP relay statistics. 132 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp relay debug traceconfig Modify DHCP relay trace configuration SYNTAX: dhcp relay debug traceconfig [state = <{disabled|enabled}]> where: state E-DOC-CTC-20071119-0014 v1.0 Enable/Disable tracing.
dhcp Commands dhcp relay delete Delete an entry from the DHCP forward list. SYNTAX: dhcp relay delete name = <{LocalNetwork_to_127.0.0.1}> where: name 134 The forward entry name. REQUIRED E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp relay flush Flushes the DHCP relay settings. E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp relay ifconfig Configure a relay interface. SYNTAX: dhcp relay ifconfig intf = <{LocalNetwork|Internet}> [relay = <{disabled|enabled}]> [maxhops = [remoteid = [trusted = <{disabled|enabled}]> where: intf The name of the relay interface to configure. REQUIRED relay Set the relay status. OPTIONAL maxhops Set the maximum number of hops allowed in the DHCP packet. OPTIONAL remoteid Set the remote id as specified in RFC3046.
dhcp Commands dhcp relay iflist Show the configuration of the relay interfaces. SYNTAX: dhcp relay iflist [intf = <{LocalNetwork|Internet}]> where: intf E-DOC-CTC-20071119-0014 v1.0 The name of the relay interface.
dhcp Commands dhcp relay list List the DHCP forward list. SYNTAX: dhcp relay list [name = <{LocalNetwork_to_127.0.0.1}]> where: name 138 The forward entry name. OPTIONAL E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp relay modify Modify an entry from the DHCP forward list. SYNTAX: dhcp relay modify name = <{LocalNetwork_to_127.0.0.1}> [addr = [intf = <{None|LocalNetwork|Internet}]> [giaddr = [script = <]> where: name The forward entry name. REQUIRED addr The DHCP server IP address. OPTIONAL intf The name of the relay interface, 'None' to indicate no interface is specified. OPTIONAL giaddr The giaddr field to be used in relayed DHCP packets.
dhcp Commands dhcp relay ruleadd Add a selection rule to a DHCP forward entry SYNTAX: dhcp relay ruleadd name = <{LocalNetwork_to_127.0.0.1}> [key = <{or|and}]> rulename = <> where: name The name of the forward entry. REQUIRED key The logical key of the selection rule. OPTIONAL rulename The name of the DHCP selection rule. REQUIRED 140 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp relay ruledelete Delete a selection rule from a DHCP forward entry SYNTAX: dhcp relay ruledelete name = <{LocalNetwork_to_127.0.0.1}> rulename = <> where: name The name of the forward entry. REQUIRED rulename The name of the DHCP selection rule. REQUIRED E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp rule add Add a rule for DHCP conditional selection SYNTAX: dhcp rule add name = type = <{option|mac|vci|uci}> option [!] = <{subnet-mask|time-offset| default-routers|time-servers|ien116-servers| impress-servers|resource-location-servers| host-name|boot-file-size|merit-dump|domainname|swap-server|root-path|extensions-path| ip-forwarding|non-local-source-routing|policyfilter|max-dgram-reassembly|default-ip-ttl| path-mtu-aging-timeout|path-mtu-plateau-table| interface-mtu|all-subn
dhcp Commands dhcp rule debug traceconfig Modify DHCP rule trace configuration SYNTAX: dhcp rule debug traceconfig [state = <{disabled|enabled}]> where: state E-DOC-CTC-20071119-0014 v1.0 Enable/Disable tracing.
dhcp Commands dhcp rule delete Delete a DHCP rule SYNTAX: dhcp rule delete name = <> where: name 144 The name of the DHCP rule. REQUIRED E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp rule flush Flush all DHCP rules E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp rule list List all DHCP rules 146 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server config Print DHCP server configuration settings SYNTAX: dhcp server config [state = <{disabled|enabled}]> where: state E-DOC-CTC-20071119-0014 v1.0 Enable/Disable the DHCP server.
dhcp Commands dhcp server debug clear Clear DHCP server statistics 148 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server debug stats Print DHCP server statistics E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server debug traceconfig Modify DHCP server trace configuration SYNTAX: dhcp server debug traceconfig [state = <{disabled|enabled}]> where: state 150 Enable/Disable tracing. OPTIONAL E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server flush Flush all DHCP server pool and lease entries E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server lease add Add a DHCP server lease SYNTAX: dhcp server lease add clientid = pool = <{LAN_private}> [addr = [offset = [leasetime = [expirytime = [gateway = [macaddr = where: clientid The DHCP client identification string of the host. REQUIRED pool The name of the DHCP server pool. REQUIRED addr The IP address for this client.
dhcp Commands dhcp server lease delete Delete a DHCP server lease SYNTAX: dhcp server lease delete [clientid = [index = [expand = <{disabled|enabled}]> where: clientid The DHCP client identification string. OPTIONAL index The DHCP server lease table index. OPTIONAL expand Expand enabled/disabled. OPTIONAL E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server lease flush Flush all DHCP server leases SYNTAX: dhcp server lease flush [pool = <{LAN_private}]> where: pool 154 The name of the DHCP server pool. Only the leases belonging to this pool will be deleted. OPTIONAL E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server lease list List all DHCP server leases SYNTAX: dhcp server lease list [clientid = [index = [expand = <{disabled|enabled}]> where: clientid The DHCP client identification string. OPTIONAL index The DHCP server lease table index. OPTIONAL expand Expand enabled/disabled. OPTIONAL E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server option flush Flush all DHCP server option templates and instances 156 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server option instadd Add a DHCP server option instance SYNTAX: dhcp server option instadd name = tmplname = <> [policy = <{requested|always|rules}]> [dynamic = <{disabled|enabled}]> [maxuse = [enterprise = [suboption = value = where: name The name of the DHCP server option instance. REQUIRED tmplname The name of the DHCP server option template.
dhcp Commands dhcp server option instdelete Delete a DHCP server option instance SYNTAX: dhcp server option instdelete name = <> [enterprise = [suboption = where: name The name of the DHCP server option instance. REQUIRED enterprise The enterprise number (see http://www.iana.org/ assignments/enterprise- numbers) OPTIONAL suboption The suboption number OPTIONAL 158 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server option instlist List all DHCP server option instances SYNTAX: dhcp server option instlist [name = <]> where: name E-DOC-CTC-20071119-0014 v1.0 The name of the DHCP server option instance.
dhcp Commands dhcp server option ruleadd Add a selection rule to a DHCP server option instance SYNTAX: dhcp server option ruleadd name = <> [key = <{or|and}]> rulename = <> where: name The name of the DHCP server option instance. REQUIRED key The logical key of the selection rule. OPTIONAL rulename The name of the DHCP selection rule. REQUIRED 160 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server option ruledelete Delete a selection rule from a DHCP server option instance SYNTAX: dhcp server option ruledelete name = <> rulename = <> where: name The name of the DHCP server option instance. REQUIRED rulename The name of the DHCP selection rule. REQUIRED E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server option tmpladd Add a DHCP server option template SYNTAX: dhcp server option tmpladd name = optionid = [dynamic = <{disabled|enabled}]> where: name The name of the DHCP server option template. REQUIRED optionid Specify the DHCP server option code. REQUIRED dynamic Enable/Disable option template as dynamic. OPTIONAL 162 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server option tmpldelete Delete a DHCP server option template SYNTAX: dhcp server option tmpldelete name = <> where: name E-DOC-CTC-20071119-0014 v1.0 The name of the DHCP server option template.
dhcp Commands dhcp server option tmpllist List all DHCP server option templates 164 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server policy Print DHCP server policy settings SYNTAX: dhcp server policy [verifyfirst = <{disabled|enabled}]> [trustclient = <{disabled|enabled}]> [rtbehaviour = <{traditional|standard|msft}]> where: verifyfirst Enable/Disable IP address conflict network probing before handing out an address to a client. OPTIONAL trustclient Whether or not the IP address suggested by a DHCP client should be taken into account.
dhcp Commands dhcp server pool add Add a DHCP server pool SYNTAX: dhcp server pool add name = [index = where: name The name of the DHCP server pool. REQUIRED index The number of the pool before which you want the new pool to be added. OPTIONAL 166 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server pool config Configure a DHCP server pool SYNTAX: dhcp server pool config name = <{LAN_private}> [state = <{disabled|enabled}]> [intf = <{Internet|LocalNetwork}]> [index = [poolstart = [poolend = [netmask = [gateway = [server = [primdns = [secdns = [dnsmetric = [primwins = [secwins = [l
dhcp Commands secdns The IP address of the secondary DNS server for DHCP clients. OPTIONAL dnsmetric The DHCP server pool DNS route metric. OPTIONAL primwins The IP address of the primary WINS server for DHCP clients. OPTIONAL secwins The IP address of the secondary WINS server for DHCP clients. OPTIONAL leasetime The time in seconds a client is allowed to use an address (tip: 0 means infinite lease). OPTIONAL renewtime The time in seconds before a client switches to renewing.
dhcp Commands dhcp server pool delete Delete a DHCP server pool SYNTAX: dhcp server pool delete name = <{LAN_private}> where: name E-DOC-CTC-20071119-0014 v1.0 The name of the DHCP server pool.
dhcp Commands dhcp server pool flush Flush all DHCP server pools 170 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server pool list List all DHCP server pools SYNTAX: dhcp server pool list [name = <{LAN_private}]> where: name E-DOC-CTC-20071119-0014 v1.0 The name of the DHCP server pool.
dhcp Commands dhcp server pool optadd Add an option instance to the DHCP server pool SYNTAX: dhcp server pool optadd name = <{LAN_private}> instname = <> where: name The name of the DHCP server pool. REQUIRED instname The name of the DHCP server option instance. REQUIRED 172 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server pool optdelete Delete an option instance from the DHCP server pool SYNTAX: dhcp server pool optdelete name = <{LAN_private}> instname = <> where: name The name of the DHCP server pool. REQUIRED instname The name of the DHCP server option instance. REQUIRED E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server pool rtadd Add a route to the DHCP server pool SYNTAX: dhcp server pool rtadd name = <{LAN_private}> dst = [dstmsk = [gateway = where: name The name of the DHCP server pool. REQUIRED dst The IP destination address of the route for DHCP clients. REQUIRED dstmsk The destination IP address mask. OPTIONAL gateway The IP address of the next hop.
dhcp Commands dhcp server pool rtdelete Delete a route from the DHCP server pool SYNTAX: dhcp server pool rtdelete name = <{LAN_private}> dst = [dstmsk = [gateway = where: name The name of the DHCP server pool. REQUIRED dst The IP destination address of the route for DHCP clients. REQUIRED dstmsk The destination IP address mask. OPTIONAL gateway The IP address of the next hop.
dhcp Commands dhcp server pool ruleadd Add a selection rule to the DHCP server pool SYNTAX: dhcp server pool ruleadd name = <{LAN_private}> [key = <{or|and}]> rulename = <> where: name The name of the DHCP server pool. REQUIRED key The logical key of the selection rule. OPTIONAL rulename The name of the DHCP selection rule. REQUIRED 176 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp server pool ruledelete Delete a selection rule from the DHCP server pool SYNTAX: dhcp server pool ruledelete name = <{LAN_private}> rulename = <> where: name The name of the DHCP server pool. REQUIRED rulename The name of the DHCP selection rule. REQUIRED E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp spoofing add Add a Spoofing-Association SYNTAX: dhcp spoofing add name = pool_name = <{LAN_private}> ifname = <> where: name The name of the Association. REQUIRED pool_name The name of the pool to be associated. REQUIRED ifname The name of the interface on which a DHCP Client is defined. REQUIRED 178 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp spoofing attach Enable a Spoofing-Association SYNTAX: dhcp spoofing attach name = <{|||}> where: name E-DOC-CTC-20071119-0014 v1.0 The name of the Association.
dhcp Commands dhcp spoofing config Display/modify dhcp spoofing state SYNTAX: dhcp spoofing config [state = <{enabled|disabled}]> where: state 180 Enable/Disable spoofing. OPTIONAL E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp spoofing debug traceconfig Display/modify DHCP spoofing trace configuratin SYNTAX: dhcp spoofing debug traceconfig [state = <{disabled|enabled}]> where: state E-DOC-CTC-20071119-0014 v1.0 Enable/Disable tracing.
dhcp Commands dhcp spoofing delete Delete a Spoofing-Association SYNTAX: dhcp spoofing delete name = <{|||}> where: name 182 The name of the Association. REQUIRED E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp spoofing detach Disable a Spoofing-Association SYNTAX: dhcp spoofing detach name = <{|||}> where: name E-DOC-CTC-20071119-0014 v1.0 The name of the Association.
dhcp Commands dhcp spoofing flush Flush all the associations and the options. 184 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp spoofing list List the available Spoofing-Associations SYNTAX: dhcp spoofing list [name = <{|||}]> where: name E-DOC-CTC-20071119-0014 v1.0 The name of the Association.
dhcp Commands dhcp spoofing option-add Add a DHCP Option Code to a Spoofing-Association. SYNTAX: dhcp spoofing option-add name = <{|||}> option = where: name The name of the Association. REQUIRED option The option id. REQUIRED 186 E-DOC-CTC-20071119-0014 v1.
dhcp Commands dhcp spoofing option-delete Delete a DHCP Option Code from a Spoofing-Association. SYNTAX: dhcp spoofing option-delete name = <{|||}> option = where: name The name of the Association. REQUIRED option The option id. REQUIRED E-DOC-CTC-20071119-0014 v1.
dns Commands 188 E-DOC-CTC-20071119-0014 v1.
dns Commands dns Commands dns client config Modify the DNS resolver configuration. see page 190 dns client dnsadd Add a DNS server. see page 191 dns client dnsdelete Delete a DNS server. see page 192 dns client dnslist List all DNS servers. see page 193 dns client flush Remove all DNS servers. see page 194 dns client nslookup DNS lookup for a domain name or an address.
dns Commands dns client config Modify the DNS resolver configuration. SYNTAX: dns client config [timeout = [retry = [search = <{disabled|enabled}]> [list = [trace = <{disabled|enabled}]> where: timeout The query timeout in seconds. OPTIONAL retry The number of query retries before giving up. OPTIONAL search Use the searchlist to construct fully qualified domain names. OPTIONAL list Slash separated list of domain name suffixes.
dns Commands dns client dnsadd Add a DNS server. SYNTAX: dns client dnsadd addr = [port = where: addr The DNS server IP address. REQUIRED port The DNS server port number. OPTIONAL E-DOC-CTC-20071119-0014 v1.
dns Commands dns client dnsdelete Delete a DNS server. SYNTAX: dns client dnsdelete index = where: index 192 The index number (shown by the 'list' command) of the server to delete. REQUIRED E-DOC-CTC-20071119-0014 v1.
dns Commands dns client dnslist List all DNS servers. E-DOC-CTC-20071119-0014 v1.
dns Commands dns client flush Remove all DNS servers. 194 E-DOC-CTC-20071119-0014 v1.
dns Commands dns client nslookup DNS lookup for a domain name or an address. SYNTAX: dns client nslookup host = where: host E-DOC-CTC-20071119-0014 v1.0 The DNS domain name string to query.
dns Commands dns server config DNS server configuration settings SYNTAX: dns server config [domain = [timeout = [suppress = [state = <{disabled|enabled}]> [trace = <{disabled|enabled}]> [syslog = <{disabled|enabled}]> [WANDownSpoofing = <{disabled|enabled}]> [WDSpoofedIP = where: domain The DNS server domain name. OPTIONAL timeout The forwarded DNS query timeout.
dns Commands dns server debug clear Clear the DNS server/forwarder statistics. E-DOC-CTC-20071119-0014 v1.
dns Commands dns server debug spoof clear Clear the intercept cache table 198 E-DOC-CTC-20071119-0014 v1.
dns Commands dns server debug spoof getaddress Get the real ip for the given spoofed ip SYNTAX: dns server debug spoof getaddress addr = where: addr E-DOC-CTC-20071119-0014 v1.0 The spoofed ip to look up.
dns Commands dns server debug spoof getflags Get the error flags for the given spoofed ip SYNTAX: dns server debug spoof getflags addr = where: addr 200 The spoofed ip to look up. REQUIRED E-DOC-CTC-20071119-0014 v1.
dns Commands dns server debug spoof list List the intercept cache table. E-DOC-CTC-20071119-0014 v1.
dns Commands dns server debug spoof update update the intercept cache table 202 E-DOC-CTC-20071119-0014 v1.
dns Commands dns server debug stats Print the DNS server/forwarder statistics. E-DOC-CTC-20071119-0014 v1.
dns Commands dns server flush Flush all local DNS hosts and routes. 204 E-DOC-CTC-20071119-0014 v1.
dns Commands dns server host add Add a local DNS host SYNTAX: dns server host add name = [addr = [ttl = where: name The name of an IP host to add. REQUIRED addr The IP address of the host. OPTIONAL ttl The lifetime of the host. OPTIONAL E-DOC-CTC-20071119-0014 v1.
dns Commands dns server host delete Delete a local DNS host SYNTAX: dns server host delete name = where: name 206 The name of an IP host to delete. REQUIRED E-DOC-CTC-20071119-0014 v1.
dns Commands dns server host flush Flush all local DNS hosts E-DOC-CTC-20071119-0014 v1.
dns Commands dns server host list List all local DNS hosts 208 E-DOC-CTC-20071119-0014 v1.
dns Commands dns server route add Creates a DNS forwarding entry or template SYNTAX: dns server route add dns = [src = [srcmask = [domain = [metric = [label = <{None|DSCP|Interactive|Management| Video|VoIP-RTP|VoIP-Signal|default}]> [intf = <{loop|Internet|LocalNetwork}]> where: dns The IP address of a DNS server. If 0.0.0.
dns Commands dns server route delete Deletes a DNS forwarding entry or template SYNTAX: dns server route delete dns = [domain = [intf = <{loop|Internet|LocalNetwork}]> where: dns The IP address of a DNS server. REQUIRED domain The DNS domain string. OPTIONAL intf The interface associated with the DNS entry or DNS Template. OPTIONAL 210 E-DOC-CTC-20071119-0014 v1.
dns Commands dns server route flush Removes all DNS forwarding entries and templates E-DOC-CTC-20071119-0014 v1.
dns Commands dns server route list Lists all DNS forwarding entries and templates 212 E-DOC-CTC-20071119-0014 v1.
dsd Commands dsd Commands dsd config Display/modify DSD framework configuration see page 214 dsd debug config Display/modify DSD debug settings see page 215 dsd debug connection list Display internal connection pool usage see page 216 dsd debug proxy Display/modify HTTPI fixed proxy settings see page 217 dsd debug recycling Display/modify HTTPI recycling settings see page 218 dsd debug stats Display/clear DSD framework and module statistics see page 219 dsd intercept config Display/modif
dsd Commands dsd config Display/modify DSD framework configuration SYNTAX: dsd config [state = <{disabled|enabled|automatic}]> where: state 214 DSD framework operation mode OPTIONAL E-DOC-CTC-20071119-0014 v1.
dsd Commands dsd debug config Display/modify DSD debug settings SYNTAX: dsd debug config [turbomode = <{disabled|enabled}]> where: turbomode E-DOC-CTC-20071119-0014 v1.
dsd Commands dsd debug connection list Display internal connection pool usage SYNTAX: dsd debug connection list [expand = <{disabled|enabled}]> where: expand 216 Expanded listing. OPTIONAL E-DOC-CTC-20071119-0014 v1.
dsd Commands dsd debug proxy Display/modify HTTPI fixed proxy settings SYNTAX: dsd debug proxy [state = <{disabled|enabled}]> [dest = [port = <{at-echo|at-nbp|at-rtmp|at-zis|auth| bgp|biff|bootpc|bootps|chargen|data|gopher| h323|httpproxy|ike|ils|imap2|imap3|ingresnet|ipcserver|ipx|irc-o|irc-u|kerberos|ldap| login|netbios-dgm|netbios-ns|netbios-ssn| netwall|netware-ip|new-rwho|nfds|nicname|nntp| ntalk|ntp|pcmail-srv|pop2|pop3|printer|qotd| realaudio|rip|rtelnet|rtsp|sip|smtp|snmp| snmptrap|s
dsd Commands dsd debug recycling Display/modify HTTPI recycling settings SYNTAX: dsd debug recycling [state = <{disabled|enabled}]> [interval = [httpidle = [otheridle = where: state Enable/disable stream recycling OPTIONAL interval Time between successive activity checks OPTIONAL httpidle Minimal idle count for recycling (filtered) http streams OPTIONAL otheridle Minimal idle count for recycling other streams OPTIONAL 218 E-DOC-CTC-20071119-0014 v1.
dsd Commands dsd debug stats Display/clear DSD framework and module statistics SYNTAX: dsd debug stats [name = <{intercept|urlfilter|recycling| syslog|all}]> [clear = <{no|yes}]> where: name Specify the name of a module OPTIONAL clear Clear the specified statistics OPTIONAL E-DOC-CTC-20071119-0014 v1.
dsd Commands dsd intercept config Display/modify HTTP Intercept configuration SYNTAX: dsd intercept config [WDSpoofedIP = [servertimeout = [connecterrorurl = [categoryerrorurl = [monitorintercepturl = [unauthorizedrequrl = [imageredirect = <{disabled|enabled}]> [imageredirecturl = [alwaysuseip = <{disabled|enabled}]> where: WDSpoofedIP IP address indicating unavailable WAN connection.
dsd Commands dsd syslog config Display/modify HTTPI logging configuration SYNTAX: dsd syslog config [syslog = <{none|unauthorized|errors| intercepted|all}]> where: syslog E-DOC-CTC-20071119-0014 v1.
dsd Commands dsd syslog list Display HTTPI log file 222 E-DOC-CTC-20071119-0014 v1.
dsd Commands dsd urlfilter config Display/modify url filtering configuration SYNTAX: dsd urlfilter config [state = <{disabled|enabled}]> [blockproxy = <{disabled|enabled}]> [blockipaddress = <{disabled|enabled}]> [blockobscuredip = <{disabled|enabled}]> [defaultaction = <{block|accept}]> where: state Enable/disable url filtering OPTIONAL blockproxy Block HTTP requests via a proxy server OPTIONAL blockipaddress Block HTTP requests if host name is IP address OPTIONAL blockobscuredip Block HTTP re
dsd Commands dsd urlfilter rule add Add a rule SYNTAX: dsd urlfilter rule add url = action = <{block|accept|redirect}> redirect = where: url Definition of the url filter REQUIRED action Action to perform when url matches url REQUIRED redirect Redirection url REQUIRED 224 E-DOC-CTC-20071119-0014 v1.
dsd Commands dsd urlfilter rule delete Remove a rule SYNTAX: dsd urlfilter rule delete index = [url = where: index Insertion position in the list REQUIRED url Definition of the url filter OPTIONAL E-DOC-CTC-20071119-0014 v1.
dsd Commands dsd urlfilter rule flush Remove all current rules 226 E-DOC-CTC-20071119-0014 v1.
dsd Commands dsd urlfilter rule list Display a list of current rules E-DOC-CTC-20071119-0014 v1.
dsd Commands dsd urlfilter rule modify Modify an existing rule SYNTAX: dsd urlfilter rule modify index = [newurl = action = <{block|accept|redirect}> redirect = where: index Insertion position in the list REQUIRED newurl Definition of the new url filter OPTIONAL action Action to perform when url matches url REQUIRED redirect Redirection url REQUIRED 228 E-DOC-CTC-20071119-0014 v1.
dyndns Commands dyndns Commands dyndns add Add a dynamic DNS client. see page 230 dyndns delete Delete a dynamic DNS client. see page 231 dyndns flush Delete all dynamic DNS clients. see page 232 dyndns host add Add a fully qualified host name see page 233 dyndns host delete Delete a host name see page 234 dyndns host flush Delete all host names see page 235 dyndns host list List all host names see page 236 dyndns list List all dynamic DNS clients.
dyndns Commands dyndns add Add a dynamic DNS client. SYNTAX: dyndns add name = where: name 230 The dynamic DNS client name. REQUIRED E-DOC-CTC-20071119-0014 v1.
dyndns Commands dyndns delete Delete a dynamic DNS client. SYNTAX: dyndns delete name = <> where: name E-DOC-CTC-20071119-0014 v1.0 The dynamic DNS client name.
dyndns Commands dyndns flush Delete all dynamic DNS clients. 232 E-DOC-CTC-20071119-0014 v1.
dyndns Commands dyndns host add Add a fully qualified host name SYNTAX: dyndns host add group = <> name = where: group The dynamic DNS host group. REQUIRED name The name of an IP host to add. REQUIRED E-DOC-CTC-20071119-0014 v1.
dyndns Commands dyndns host delete Delete a host name SYNTAX: dyndns host delete name = <> where: name 234 The name of an IP host to delete. REQUIRED E-DOC-CTC-20071119-0014 v1.
dyndns Commands dyndns host flush Delete all host names E-DOC-CTC-20071119-0014 v1.
dyndns Commands dyndns host list List all host names 236 E-DOC-CTC-20071119-0014 v1.
dyndns Commands dyndns list List all dynamic DNS clients. E-DOC-CTC-20071119-0014 v1.
dyndns Commands dyndns modify Modify a dynamic DNS client. SYNTAX: dyndns modify name = <> [intf = <{loop|Internet|LocalNetwork}]> [user = [password = [group = <]> [mx = [backmx = <{disabled|enabled}]> [wildcard = <{disabled|enabled}]> [offline = <{disabled|enabled}]> [service = <{dyndns|statdns|custom|No-IP| DtDNS|gnudip}]> [status = <{disabled|enabled}]> [trace = <{disabled|enabled}]> where: name The dynamic DNS client name.
dyndns Commands dyndns service list List all dynamic DNS services E-DOC-CTC-20071119-0014 v1.
dyndns Commands dyndns service modify Modify specific dynamic DNS service settings SYNTAX: dyndns service modify name = <{dyndns|statdns|custom|No-IP|DtDNS| gnudip}> [server = [port = <{at-echo|at-nbp|at-rtmp|at-zis|auth| bgp|biff|bootpc|bootps|chargen|data|gopher| h323|httpproxy|ike|ils|imap2|imap3|ingresnet|ipcserver|ipx|irc-o|irc-u|kerberos|ldap| login|netbios-dgm|netbios-ns|netbios-ssn| netwall|netware-ip|new-rwho|nfds|nicname|nntp| ntalk|ntp|pcmail-srv|pop2|pop3|printer|qotd| realaudio|rip|
env Commands env Commands env flush Remove all non-system environment variables. see page 242 env get Gets an environment variable. see page 243 env list List all environment variables. see page 244 env set Sets an environment variable. see page 245 env unset Deletes an environment variable. see page 246 E-DOC-CTC-20071119-0014 v1.
env Commands env flush Remove all non-system environment variables. 242 E-DOC-CTC-20071119-0014 v1.
env Commands env get Gets an environment variable.
env Commands env list List all environment variables. 244 E-DOC-CTC-20071119-0014 v1.
env Commands env set Sets an environment variable. SYNTAX: env set var = value = where: var The name of the variable. REQUIRED value A translated quoted string defining the variable value. REQUIRED E-DOC-CTC-20071119-0014 v1.
env Commands env unset Deletes an environment variable.
eth Commands eth Commands eth bridge add Add a new bridge instance. see page 251 eth bridge clear Clear bridge statistics. see page 252 eth bridge config Modify/Display the bridge configuration settings. see page 253 eth bridge delete Delete a bridge instance. see page 254 eth bridge dynvlan actlist Display the active MAC entries for the dynamic VLAN membership. see page 255 eth bridge dynvlan add Add a dynamic VLAN membership entry.
eth Commands eth bridge igmpsnooping list Display bridge instance snooped groups. see page 274 eth bridge list Display the current bridge instances. see page 275 eth bridge macadd Add a static MAC address to a bridge interface. see page 276 eth bridge macdelete Remove a MAC address from the database. see page 277 eth bridge maclist Display the MAC address database. see page 278 eth bridge rule add Add a new constraint to the VLAN learning system.
eth Commands eth bridge xtratag list Display all extra tag mapping entries. see page 296 eth device ifconfig Configure ethernet interface. see page 297 eth device iflist Show status of ethernet interfaces. see page 298 eth flush Flush all ETH interfaces. see page 299 eth ifadd Create a new ETH interface. see page 300 eth ifattach Attach an ETH interface. see page 301 eth ifconfig Modify an ETH interface. see page 302 eth ifdelete Delete an ETH interface.
eth Commands eth switch share list Display shared ports. see page 322 eth switch storm ifconfig Configure per port storm control parameters. see page 323 eth switch storm iflist Display storm control configuration per port. see page 324 eth vlan add Add a new virtual LAN. see page 325 eth vlan delete Delete a virtual LAN. see page 326 eth vlan flush Flush all virtual LAN's. see page 327 eth vlan list Display all virtual LAN's. see page 328 250 E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge add Add a new bridge instance. SYNTAX: eth bridge add brname = where: brname E-DOC-CTC-20071119-0014 v1.0 The name of the new bridge instance.
eth Commands eth bridge clear Clear bridge statistics. SYNTAX: eth bridge clear [brname = <{bridge}]> where: brname 252 The name of a bridge instance. OPTIONAL E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge config Modify/Display the bridge configuration settings. SYNTAX: eth bridge config [brname = <{bridge}]> [age = [filter = <{none|no_WAN_broadcast}]> [vlan = <{disabled|enabled}]> [precedencemap = where: brname The name of a bridge instance. OPTIONAL age The lifetime (in seconds) of a dynamically learned MAC address. OPTIONAL filter The bridge filter to be applied for all WAN bridge interfaces.
eth Commands eth bridge delete Delete a bridge instance. SYNTAX: eth bridge delete brname = <{bridge}> where: brname 254 The name of a bridge instance. REQUIRED E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge dynvlan actlist Display the active MAC entries for the dynamic VLAN membership. E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge dynvlan add Add a dynamic VLAN membership entry. SYNTAX: eth bridge dynvlan add [id = hwaddr = vlan = <{default}> [remvlan = <{default}]> where: id The id of the dynamic VLAN membership entry. OPTIONAL hwaddr The (masked) ethernet MAC address of the dynamic VLAN membership entry. REQUIRED vlan The VLAN for the dynamic VLAN membership entry. REQUIRED remvlan The VLAN that will be removed from the bridge interface.
eth Commands eth bridge dynvlan config Modify the dynamic VLAN membership configuration. SYNTAX: eth bridge dynvlan config [timeout = where: timeout E-DOC-CTC-20071119-0014 v1.0 Timeout in seconds for the dynamic entries.
eth Commands eth bridge dynvlan delete Delete a dynamic VLAN membership entry. SYNTAX: eth bridge dynvlan delete id = where: id 258 REQUIRED E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge dynvlan flush Flush all dynamic VLAN membership entries. E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge dynvlan list Display a dynamic VLAN membership entry. 260 E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge flush Flush all bridge instances with their interfaces and properties. SYNTAX: eth bridge flush [brname = <{bridge}]> where: brname E-DOC-CTC-20071119-0014 v1.0 The name of a bridge instance.
eth Commands eth bridge ifadd Add a new bridge interface. SYNTAX: eth bridge ifadd [brname = <{bridge}]> intf = where: brname The name of a bridge instance. OPTIONAL intf The new bridge interface name. REQUIRED 262 E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge ifattach Attach a bridge interface. SYNTAX: eth bridge ifattach [brname = <{bridge}]> intf = <{}> where: brname The name of a bridge instance. OPTIONAL intf The name of the bridge interface. REQUIRED E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge ifconfig Modify a bridge interface configuration.
eth Commands regenprio The priority regeneration table for tagged ingress packets. OPTIONAL ingressfiltering Enable/disable discard of tagged ingress packets if the interface is not part of the VLAN. OPTIONAL acceptvlanonly Enable/disable receipt of tagged ingress packets. OPTIONAL mcastfilter Enable/disable discard of multicast packets for this interface. OPTIONAL dynvlan Enable/disable dynamic VLAN membership checking for this interface. OPTIONAL wan Enable/disable WAN for this interface.
eth Commands eth bridge ifdelete Delete a bridge interface. SYNTAX: eth bridge ifdelete [brname = <{bridge}]> intf = <{ethport1|ethport2|ethport3|ethport4| WLAN}> where: brname The name of a bridge instance. OPTIONAL intf The name of the bridge interface. REQUIRED 266 E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge ifdetach Detach a bridge interface. SYNTAX: eth bridge ifdetach [brname = <{bridge}]> intf = <{ethport1|ethport2|ethport3|ethport4| WLAN}> where: brname The name of a bridge instance. OPTIONAL intf The name of the bridge interface. REQUIRED E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge ifflush flush the bridge interfaces: detach/delete all interfaces. SYNTAX: eth bridge ifflush [brname = <{bridge}]> where: brname 268 The name of a bridge instance. OPTIONAL E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge iflist Display the current bridge interfaces. SYNTAX: eth bridge iflist [brname = <{bridge}]> [intf = <{OBC|ethport1|ethport2|ethport3| ethport4|WLAN}]> where: brname The name of a bridge instance. OPTIONAL intf The name of a bridge interface. OPTIONAL E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge igmpsnooping clear Clear snooping statistics. SYNTAX: eth bridge igmpsnooping clear [brname = <{bridge}]> [intf = <{OBC|ethport1|ethport2|ethport3| ethport4|WLAN}]> where: brname The name of a bridge instance. OPTIONAL intf The bridge interface currently to be cleared. OPTIONAL 270 E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge igmpsnooping config Configure bridge instance IGMP Snooping flags. SYNTAX: eth bridge igmpsnooping config [brname = <{bridge}]> [state = <{disabled|enabled}]> [floodrp = <{disabled|enabled}]> [floodmcast = <{disabled|enabled}]> where: brname The name of a bridge instance. OPTIONAL state Enable/Disable the IGMP Snooping. OPTIONAL floodrp Enable/Disable flooding reports to all ports. OPTIONAL floodmcast Enable/Disable flooding unregistered multicasts.
eth Commands eth bridge igmpsnooping ifconfig Configure bridge interface IGMP snooping flags and mode. SYNTAX: eth bridge igmpsnooping ifconfig [brname = <{bridge}]> intf = <{OBC|ethport1|ethport2|ethport3| ethport4|WLAN}> [portmode = <{Host|Router|Auto}]> [fastleave = <{disabled|enabled}]> [exptrack = <{disabled|enabled}]> [mrdp = <{disabled|enabled}]> [rgmp = <{disabled|enabled}]> where: brname The bridge instance currently to be configured.
eth Commands eth bridge igmpsnooping iflist Display bridge interface IGMP status. SYNTAX: eth bridge igmpsnooping iflist [brname = <{bridge}]> [intf = <{OBC|ethport1|ethport2|ethport3| ethport4|WLAN}]> where: brname The name of a bridge instance. OPTIONAL intf The name of the bridge interface. OPTIONAL E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge igmpsnooping list Display bridge instance snooped groups. SYNTAX: eth bridge igmpsnooping list [brname = <{bridge}]> where: brname 274 The name of a bridge instance. OPTIONAL E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge list Display the current bridge instances. SYNTAX: eth bridge list [brname = <{bridge}]> where: brname E-DOC-CTC-20071119-0014 v1.0 The name of a bridge instance.
eth Commands eth bridge macadd Add a static MAC address to a bridge interface. SYNTAX: eth bridge macadd [brname = <{bridge}]> intf = <{OBC|ethport1|ethport2|ethport3| ethport4|WLAN}> hwaddr = [vlan = <{default}]> where: brname The name of a bridge instance. OPTIONAL intf The name of the bridge interface. REQUIRED hwaddr The ethernet MAC address of the new entry. REQUIRED vlan The VLAN. OPTIONAL 276 E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge macdelete Remove a MAC address from the database. SYNTAX: eth bridge macdelete [brname = <{bridge}]> hwaddr = [vlan = <{default}]> where: brname The name of a bridge instance. OPTIONAL hwaddr The ethernet MAC address of the entry. REQUIRED vlan The VLAN. OPTIONAL E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge maclist Display the MAC address database. SYNTAX: eth bridge maclist [brname = <{bridge}]> where: brname 278 The name of a bridge instance. OPTIONAL E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge rule add Add a new constraint to the VLAN learning system. SYNTAX: eth bridge rule add type = vlan = [vlan2 [isi = <{shared|independant}> <{default}> = <{default}]> where: type Type of constraint. REQUIRED vlan The VLAN where the constraint belongs to. REQUIRED vlan2 The second VLAN for a shared constraint. OPTIONAL isi The indenpendent set id for an independent constraint. OPTIONAL E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge rule delete Delete a constraint from the VLAN learning system. SYNTAX: eth bridge rule delete index = where: index 280 Index of the constraint. REQUIRED E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge rule flush Flush all constraints from the VLAN learning system. E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge rule list Display all constraints from the VLAN learning system. 282 E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge select Select the default bridge for configuring interfaces from (if not setting SYNTAX: eth bridge select brname = <{bridge}> where: brname E-DOC-CTC-20071119-0014 v1.0 The name of a bridge instance.
eth Commands eth bridge unknownvlan ifadd Add bridge interface to unknown 'VLAN'. SYNTAX: eth bridge unknownvlan ifadd [brname = <{bridge}]> intf = <{OBC|ethport1|ethport2|ethport3| ethport4|WLAN}> [untagged = <{disabled|enabled}]> where: brname The name of a bridge instance. OPTIONAL intf The name of the bridge interface to add to the unknown 'VLAN'. REQUIRED untagged Enable/disable interface as untagged for this unknown 'VLAN'. OPTIONAL 284 E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge unknownvlan ifconfig Modify bridge interface from unknown 'VLAN'. SYNTAX: eth bridge unknownvlan ifconfig [brname = <{bridge}]> intf = <{OBC|ethport1|ethport2|ethport3| ethport4|WLAN}> [untagged = <{disabled|enabled}]> where: brname The name of a bridge instance. OPTIONAL intf The bridge interface from the unknown 'VLAN' to configure. REQUIRED untagged Enable/disable interface as untagged for this unknown 'VLAN'. OPTIONAL E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge unknownvlan ifdelete Delete bridge interface from unknown 'VLAN'. SYNTAX: eth bridge unknownvlan ifdelete [brname = <{bridge}]> intf = <{OBC|ethport1|ethport2|ethport3| ethport4|WLAN}> where: brname The name of a bridge instance. OPTIONAL intf The name of the bridge interface to remove from the unknown 'VLAN'. REQUIRED 286 E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge unknownvlan iflist Display all interfaces of the unknown 'VLAN'. E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge vlan ifadd Add bridge interface to virtual LAN. SYNTAX: eth bridge vlan ifadd name = <{default}> intf = <{OBC|ethport1|ethport2|ethport3| ethport4|WLAN}> [untagged = <{disabled|enabled}]> where: name The VLAN name. REQUIRED intf The name of the bridge interface to add to the VLAN. REQUIRED untagged Enable/disable interface as untagged for this VLAN. OPTIONAL 288 E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge vlan ifconfig Modify bridge interface from virtual LAN. SYNTAX: eth bridge vlan ifconfig name = <{default}> intf = <{OBC|ethport1|ethport2|ethport3| ethport4|WLAN}> untagged = <{disabled|enabled}> where: name The VLAN name. REQUIRED intf The bridge interface from the VLAN to configure. REQUIRED untagged Enable/disable interface as untagged for this VLAN. REQUIRED E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge vlan ifdelete Delete bridge interface from virtual LAN. SYNTAX: eth bridge vlan ifdelete name = <{default}> intf = <{OBC|ethport1|ethport2|ethport3| ethport4|WLAN}> where: name The VLAN name. REQUIRED intf The name of the bridge interface to remove from the VLAN. REQUIRED 290 E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge vlan iflist Display all vitual LAN's. E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge xtratag add Add an extra tag mapping entry. SYNTAX: eth bridge xtratag add [brname = <{bridge}]> intf = <{OBC|ethport1|ethport2|ethport3| ethport4|WLAN}> innervid = <{[1-4094]|all|}> outervid = <{[1-4094]|notag|transparant|}> where: brname The name of a bridge instance. OPTIONAL intf The name of the bridge interface. REQUIRED innervid The inner VLAN id [all,1-4094] (all = all inner vid will be translated to the outer vid).
eth Commands eth bridge xtratag config Configure an extra tag mapping entry. SYNTAX: eth bridge xtratag config [brname = <{bridge}]> intf = <{OBC|ethport1|ethport2|ethport3| ethport4|WLAN}> innervid = <{[1-4094]|all|}> outervid = <{[1-4094]|notag|transparant|}> where: brname The name of a bridge instance. OPTIONAL intf The name of the bridge interface. REQUIRED innervid The inner VLAN id [all,1-4094] (all = all inner vid will be translated to the outer vid).
eth Commands eth bridge xtratag delete Delete an extra tag mapping entry. SYNTAX: eth bridge xtratag delete [brname = <{bridge}]> intf = <{OBC|ethport1|ethport2|ethport3| ethport4|WLAN}> innervid = <{[1-4094]|all|}> where: brname The name of a bridge instance. OPTIONAL intf The name of the bridge interface. REQUIRED innervid The inner VLAN id [all,1-4094] (all = all inner vid will be translated to the outer vid). REQUIRED 294 E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge xtratag flush Flush all extra tag mapping entries. E-DOC-CTC-20071119-0014 v1.
eth Commands eth bridge xtratag list Display all extra tag mapping entries. 296 E-DOC-CTC-20071119-0014 v1.
eth Commands eth device ifconfig Configure ethernet interface. SYNTAX: eth device ifconfig intf = <{ethif1|ethif2|ethif3|ethif4|wlif1}> [type = <{auto|10BaseTHD|10BaseTFD|100BaseTHD| 100BaseTFD} or number]> [state = <{enabled|disabled}]> where: intf The name of a physical interface. REQUIRED type The ethernet type. OPTIONAL state The interface state. OPTIONAL E-DOC-CTC-20071119-0014 v1.
eth Commands eth device iflist Show status of ethernet interfaces. 298 E-DOC-CTC-20071119-0014 v1.
eth Commands eth flush Flush all ETH interfaces. E-DOC-CTC-20071119-0014 v1.
eth Commands eth ifadd Create a new ETH interface. SYNTAX: eth ifadd intf = where: intf 300 The name for the new ETH interface. REQUIRED E-DOC-CTC-20071119-0014 v1.
eth Commands eth ifattach Attach an ETH interface. SYNTAX: eth ifattach intf = <{}> where: intf E-DOC-CTC-20071119-0014 v1.0 The name of the ETH interface.
eth Commands eth ifconfig Modify an ETH interface. SYNTAX: eth ifconfig intf = <{ethoa_8_35}> [dest = <{bridge|ethoa_8_35}]> [retry = [wan = <{disabled|enabled}]> [priotag = <{disabled|enabled}]> [vlan = <{default}]> where: intf The name of the ETH interface to configure. REQUIRED dest The destination interface for this ETH interface. OPTIONAL retry The number of times the ETH connection setup should retry before giving up.
eth Commands eth ifdelete Delete an ETH interface. SYNTAX: eth ifdelete intf = <{}> where: intf E-DOC-CTC-20071119-0014 v1.0 The name of the ETH interface.
eth Commands eth ifdetach Detach an ETH interface. SYNTAX: eth ifdetach intf = <{ethoa_8_35}> where: intf 304 The name of the ETH interface. REQUIRED E-DOC-CTC-20071119-0014 v1.
eth Commands eth iflist Display the ETH interfaces. SYNTAX: eth iflist [intf = <{ethoa_8_35}]> where: intf E-DOC-CTC-20071119-0014 v1.0 The name of an ETH interface.
eth Commands eth switch group flush To set all ports to the default settings (all ports in group 0). 306 E-DOC-CTC-20071119-0014 v1.
eth Commands eth switch group list List all configured groups. E-DOC-CTC-20071119-0014 v1.
eth Commands eth switch group move Move a specified port to a specified group. SYNTAX: eth switch group move group = port = where: group The group id. REQUIRED port The port. REQUIRED 308 E-DOC-CTC-20071119-0014 v1.
eth Commands eth switch info Display switch capabilities E-DOC-CTC-20071119-0014 v1.
eth Commands eth switch mirror capture Define the specified port to be the Mirror Capture Port. SYNTAX: eth switch mirror capture port = where: port 310 The port. REQUIRED E-DOC-CTC-20071119-0014 v1.
eth Commands eth switch mirror egress Enable or disable the specified port to be a Transmitted Port Mirroring. SYNTAX: eth switch mirror egress port = [state = <{enabled|disabled}]> where: port The port. REQUIRED state Enable/disable state. OPTIONAL E-DOC-CTC-20071119-0014 v1.
eth Commands eth switch mirror ingress Enable or disable the specified port to be a Received Port Mirroring. SYNTAX: eth switch mirror ingress port = [state = <{enabled|disabled}]> where: port The port. REQUIRED state Enable/disable state. OPTIONAL 312 E-DOC-CTC-20071119-0014 v1.
eth Commands eth switch qos config Configure common qos parameters. SYNTAX: eth switch qos config state = <{enabled|disabled}> [nbrOfQueues = [realtime = <{enabled|disabled}]> where: state Enable/disable QoS. REQUIRED nbrOfQueues Number of queues. OPTIONAL realtime Enable/disable realtime. OPTIONAL E-DOC-CTC-20071119-0014 v1.
eth Commands eth switch qos ifconfig Configure per port qos parameters. SYNTAX: eth switch qos ifconfig port = mode = <{none|802.1p|high|diffserv}> [flowcontrol = <{disabled|enabled}]> where: port The port. REQUIRED mode Classifier. REQUIRED flowcontrol Enable/disable flow-control. OPTIONAL 314 E-DOC-CTC-20071119-0014 v1.
eth Commands eth switch qos list Display qos configuration. E-DOC-CTC-20071119-0014 v1.
eth Commands eth switch qos weights Configure the queue weights. SYNTAX: eth switch qos weights queue0 queue1 queue2 queue3 = = = = where: queue0 Weight of queue 0 in WFQ (in %). REQUIRED queue1 Weight of queue 1 in WFQ (in %). REQUIRED queue2 Weight of queue 2 in WFQ (in %). REQUIRED queue3 Weight of queue 3 in WFQ (in %). REQUIRED 316 E-DOC-CTC-20071119-0014 v1.
eth Commands eth switch shaper config Configure common ingress shaper parameters. SYNTAX: eth switch shaper config shaper = [unicast = <{enabled|disabled}]> [multicast = <{enabled|disabled}]> [broadcast = <{enabled|disabled}]> [control = <{enabled|disabled}]> [unknown = <{enabled|disabled}]> [discard = <{enabled|disabled}]> where: shaper The shaper instance. REQUIRED unicast Shape unicast traffic. OPTIONAL multicast Shape multicast traffic.
eth Commands eth switch shaper ifconfig Configure per port shaper parameters. SYNTAX: eth switch shaper ifconfig port = ingress = <{enabled|disabled}> shaper = [state = <{enabled|disabled}]> [speed = [burstsize = <{}]> where: port The port. REQUIRED ingress Ingress port = enabled; egress port = disabled. REQUIRED shaper The shaper instance. REQUIRED state Enable/disable shaping. OPTIONAL speed Speed in bits/sec.
eth Commands eth switch shaper iflist Display shaper configuration per port. E-DOC-CTC-20071119-0014 v1.
eth Commands eth switch share add Add a port to be shared. SYNTAX: eth switch share add port = shared = where: port The port. REQUIRED shared The shared port. REQUIRED 320 E-DOC-CTC-20071119-0014 v1.
eth Commands eth switch share delete Delete a shared port. SYNTAX: eth switch share delete port = shared = where: port The port. REQUIRED shared The shared port. REQUIRED E-DOC-CTC-20071119-0014 v1.
eth Commands eth switch share list Display shared ports. 322 E-DOC-CTC-20071119-0014 v1.
eth Commands eth switch storm ifconfig Configure per port storm control parameters. SYNTAX: eth switch storm ifconfig port = [state = <{enabled|disabled}]> [rate = <{100|200|300|400}]> [burstsize = [broadcast = <{enabled|disabled}]> [multicast = <{enabled|disabled}]> [unknown = <{enabled|disabled}]> where: port The port. REQUIRED state Enable/disable storm control. OPTIONAL rate Rate in 10ths of percent. OPTIONAL burstsize Burst size in KBytes.
eth Commands eth switch storm iflist Display storm control configuration per port. 324 E-DOC-CTC-20071119-0014 v1.
eth Commands eth vlan add Add a new virtual LAN. SYNTAX: eth vlan add name = vid = [addrule = <{disabled|enabled}]> where: name The new VLAN name. REQUIRED vid The new VLAN id. REQUIRED addrule Add the default bridge constraint. OPTIONAL E-DOC-CTC-20071119-0014 v1.
eth Commands eth vlan delete Delete a virtual LAN. SYNTAX: eth vlan delete name = <{default}> where: name 326 The VLAN name. REQUIRED E-DOC-CTC-20071119-0014 v1.
eth Commands eth vlan flush Flush all virtual LAN's. E-DOC-CTC-20071119-0014 v1.
eth Commands eth vlan list Display all virtual LAN's. 328 E-DOC-CTC-20071119-0014 v1.
exit Command exit Command Exits this shell. E-DOC-CTC-20071119-0014 v1.
expr Commands 330 E-DOC-CTC-20071119-0014 v1.
expr Commands expr Commands expr add Add an expression. see page 332 expr delete Delete an expression. see page 335 expr flush Flush all expressions. see page 336 expr list List expressions. see page 337 expr modify Modify an expression. see page 338 E-DOC-CTC-20071119-0014 v1.
expr Commands expr add Add an expression.
expr Commands ftp-data|gopher|h323|httpproxy|ike|ils|imap2| imap3|ingres-net|ipcserver|ipx|irc-o|irc-u| kerberos|ldap|login|netbios-dgm|netbios-ns| netbios-ssn|netwall|netware-ip|new-rwho|nfds| nicname|nntp|ntalk|ntp|pcmail-srv|pop2|pop3| printer|qotd|realaudio|rip|rtelnet|rtsp|sip| smtp|snmp|snmptrap|snpp|sntp|sql*net|sqlnet|sqlserv|sunrpc|syslog|systat|talk|...
expr Commands precedence [!] The precedence in the IP packet (part of tos). OPTIONAL If a value is preceded by a “!”, it means NOT. dscp [!] The diffserv code point in the IP packet (part of tos). OPTIONAL If a value is preceded by a “!”, it means NOT. proto [!] The IP protocol (name or number) in the IP packet. OPTIONAL If a value is preceded by a “!”, it means NOT. srcport [!] The TCP/UDP source port number or range begin. OPTIONAL If a value is preceded by a “!”, it means NOT.
expr Commands expr delete Delete an expression. SYNTAX: expr delete name = <{wan|local|lan|tunnel|dmz|guest| private|ssdp_ip|mdap_ip|icmp|igmp|imaps|pop2| pop3|pop3s|smtp|ssh|dns|nntp|ipsec|esp|ah| ike|DiffServ|sip|h323|dhcp|rtsp|ssdp_serv| mdap_serv|syslog}> [index = where: name The name of an expression to delete. REQUIRED index The index of a subexpression. OPTIONAL E-DOC-CTC-20071119-0014 v1.
expr Commands expr flush Flush all expressions. 336 E-DOC-CTC-20071119-0014 v1.
expr Commands expr list List expressions.
expr Commands expr modify Modify an expression.
expr Commands [dstport [!] = <{at-echo|at-nbp|at-rtmp|atzis|auth|bgp|biff|bootpc|bootps|finger|ftp| ftp-data|gopher|h323|httpproxy|ike|ils|imap2| imap3|ingres-net|ipcserver|ipx|irc-o|irc-u| kerberos|ldap|login|netbios-dgm|netbios-ns| netbios-ssn|netwall|netware-ip|new-rwho|nfds| nicname|nntp|ntalk|ntp|pcmail-srv|pop2|pop3| printer|qotd|realaudio|rip|rtelnet|rtsp|sip| smtp|snmp|snmptrap|snpp|sntp|sql*net|sqlnet|sqlserv|sunrpc|syslog|systat|talk|...
expr Commands tos [!] The Type Of Service specification in the IP packet. OPTIONAL If a value is preceded by a “!”, it means NOT. precedence [!] The precedence in the IP packet (part of tos). OPTIONAL If a value is preceded by a “!”, it means NOT. dscp [!] The diffserv code point in the IP packet (part of tos). OPTIONAL If a value is preceded by a “!”, it means NOT. proto [!] The IP protocol (name or number) in the IP packet. OPTIONAL If a value is preceded by a “!”, it means NOT.
firewall Commands firewall Commands firewall chain add Add a chain. see page 342 firewall chain delete Delete a chain. see page 343 firewall chain flush Flush all chains. see page 344 firewall chain list Display a list of chains. see page 345 firewall clear Clear firewall configuration. see page 346 firewall config Display/Modify firewall configuration. see page 347 firewall debug clear Clear firewall statistics. see page 348 firewall debug stats Display firewall statistics.
firewall Commands firewall chain add Add a chain. SYNTAX: firewall chain add chain = where: chain 342 The name of the chain to add. REQUIRED E-DOC-CTC-20071119-0014 v1.
firewall Commands firewall chain delete Delete a chain. SYNTAX: firewall chain delete chain = where: chain E-DOC-CTC-20071119-0014 v1.0 The name of the chain to delete.
firewall Commands firewall chain flush Flush all chains. 344 E-DOC-CTC-20071119-0014 v1.
firewall Commands firewall chain list Display a list of chains. SYNTAX: firewall chain list [format = <{pretty|cli}]> where: format E-DOC-CTC-20071119-0014 v1.0 The format of the chain list.
firewall Commands firewall clear Clear firewall configuration. 346 E-DOC-CTC-20071119-0014 v1.
firewall Commands firewall config Display/Modify firewall configuration. SYNTAX: firewall config [state = <{disabled|enabled}]> [keep = <{disabled|enabled}]> [tcpchecks = <{none|fast|exact}]> [udpchecks = <{disabled|enabled}]> [icmpchecks = <{disabled|enabled}]> [logdefault = <{disabled|enabled}]> [logthreshold = <{disabled|enabled}]> [tcpwindow = where: state Disable/Enable the firewall. OPTIONAL keep Disable/Enable keeping existing connections when firewall rules change.
firewall Commands firewall debug clear Clear firewall statistics. 348 E-DOC-CTC-20071119-0014 v1.
firewall Commands firewall debug stats Display firewall statistics. E-DOC-CTC-20071119-0014 v1.
firewall Commands firewall level add Add a new security level. SYNTAX: firewall level add name = [index = [readonly = <{disabled|enabled}]> [udptrackmode = <{strict|loose}]> [service = <{disabled|enabled}]> [proxy = <{disabled|enabled}]> [text = [policy = <{default|drop|accept}]> where: name The name of the security level to add. REQUIRED index The index of the security level. OPTIONAL readonly Select whether the security level is readonly.
firewall Commands firewall level delete Delete a security level. SYNTAX: firewall level delete name = where: name E-DOC-CTC-20071119-0014 v1.0 The name of the security level to delete.
firewall Commands firewall level flush Flush security level configuration. 352 E-DOC-CTC-20071119-0014 v1.
firewall Commands firewall level list List all security levels. SYNTAX: firewall level list [format = <{pretty|cli}]> where: format E-DOC-CTC-20071119-0014 v1.0 The format of the security level list.
firewall Commands firewall level modify Modify a security level. SYNTAX: firewall level modify name = [index = [readonly = <{disabled|enabled}]> [udptrackmode = <{strict|loose}]> [service = <{disabled|enabled}]> [proxy = <{disabled|enabled}]> [text = [policy = <{default|drop|accept}]> where: name The name of the security level to modify. REQUIRED index The index of this security level. OPTIONAL readonly Select whether the security level is readonly.
firewall Commands firewall level set Set/Display active security level. SYNTAX: firewall level set [name = where: name E-DOC-CTC-20071119-0014 v1.0 The name of the security level to set active.
firewall Commands firewall list Display firewall configuration. SYNTAX: firewall list [format = <{pretty|cli}]> where: format 356 The format of the firewall list. OPTIONAL E-DOC-CTC-20071119-0014 v1.
firewall Commands firewall rule add Add a rule.
firewall Commands log Disable/Enable logging when this rule applies. OPTIONAL state Disable/Enable this rule. OPTIONAL action The action to be taken when this rule applies ('link' when clink is used). REQUIRED 358 E-DOC-CTC-20071119-0014 v1.
firewall Commands firewall rule delete Delete a rule. SYNTAX: firewall rule delete chain = index = where: chain The name of the chain in which to delete the rule. REQUIRED index The number of the rule in the chain. REQUIRED E-DOC-CTC-20071119-0014 v1.
firewall Commands firewall rule flush Flush all rules. SYNTAX: firewall rule flush [chain = where: chain 360 The name of the chain to flush. OPTIONAL E-DOC-CTC-20071119-0014 v1.
firewall Commands firewall rule list Display a list of rules. SYNTAX: firewall rule list [chain = [format = <{pretty|cli}]> where: chain The name of the chain to list the rules of. OPTIONAL format The format of the rule list. OPTIONAL E-DOC-CTC-20071119-0014 v1.
firewall Commands firewall rule modify Modify a rule. SYNTAX: firewall rule modify chain = [index = [newindex = [name = [clink = [[!]srcintf] = [[!]srcip] = [[!]dstintf] = [[!]dstip] = [[!]serv] = [log = <{disabled|enabled}]> [state = <{disabled|enabled}]> [action = <{accept|deny|drop|reset|count| link}]> where: chain The name of the chain which contains the rule.
firewall Commands state Disable/Enable this rule. OPTIONAL action The action to be taken when this rule applies ('link' when clink is used). OPTIONAL E-DOC-CTC-20071119-0014 v1.
grp Commands 364 E-DOC-CTC-20071119-0014 v1.
grp Commands grp Commands grp config Set the grp configuration settings. see page 366 grp flush Flush grp interface settings and parameters. see page 367 grp rip config Set the RIP configuration settings. see page 368 grp rip flush Flush RIP interface settings and global parameters. see page 369 grp rip ifconfig Configure a RIP interface. see page 370 grp rip show Show the RIP settings and the routes in the RIP database.
grp Commands grp config Set the grp configuration settings. SYNTAX: grp config [cdistance = [kdistance = [rdistance = [trace = <{disabled|enabled}]> where: cdistance Set the distance of the connected route type. Default distance is 0. OPTIONAL kdistance Set the distance of the kernel route type. Default distance is 1. OPTIONAL rdistance Set the distance of the RIP route type. Default distance is 120. OPTIONAL trace Enable/Disable tracing.
grp Commands grp flush Flush grp interface settings and parameters. E-DOC-CTC-20071119-0014 v1.
grp Commands grp rip config Set the RIP configuration settings. SYNTAX: grp rip config state = <{disabled|enabled}> [version = <{rip_unspec|rip_v1|rip_v2}]> [updatetime = where: state Enable/Disable the RIP daemon. REQUIRED version Set the RIP version. OPTIONAL updatetime Set the routing table update timer value. Default is 30 seconds. OPTIONAL 368 E-DOC-CTC-20071119-0014 v1.
grp Commands grp rip flush Flush RIP interface settings and global parameters. E-DOC-CTC-20071119-0014 v1.
grp Commands grp rip ifconfig Configure a RIP interface. SYNTAX: grp rip ifconfig intf = <{LocalNetwork|Internet}> [rip = <{disabled|enabled}]> [rxversion = <{rip_unspec|rip_v1|rip_v2| rip_v1-2}]> [authmode = <{none|cleartext}]> [authstr = [splithorizon = <{disabled|enabled}]> where: intf The name of the RIP interface to configure. REQUIRED rip Enable/Disable the RIP status. OPTIONAL rxversion Set the RIP receive version. OPTIONAL authmode Set the RIP authentication mode.
grp Commands grp rip show Show the RIP settings and the routes in the RIP database. E-DOC-CTC-20071119-0014 v1.
grp Commands grp rtlist Show the current routes in the grp routing table. SYNTAX: grp rtlist [dst = [dstmsk = where: dst The destination IP address using this route. Supports ip/mask notation. OPTIONAL dstmsk The destination IP address mask. OPTIONAL 372 E-DOC-CTC-20071119-0014 v1.
help Command help Command Displays this help information E-DOC-CTC-20071119-0014 v1.
hostmgr Commands 374 E-DOC-CTC-20071119-0014 v1.
hostmgr Commands hostmgr Commands hostmgr add Add host device info to hostmgr see page 376 hostmgr clear Remove all hosts from list see page 377 hostmgr config Config hostmgr parameters see page 378 hostmgr delete Delete host device info from hostmgr see page 379 hostmgr flush Flushes hostmgr configuration (i.e. clean & to defaults) see page 380 hostmgr list List all host devices see page 381 E-DOC-CTC-20071119-0014 v1.
hostmgr Commands hostmgr add Add host device info to hostmgr SYNTAX: hostmgr add mac_addr = [ip_addr = [name = [type = <{generic_device|desktop_computer| laptop_computer|set_top_box|pda| gaming_console|phone|mobile_phone|printer| mass_storage_device}]> [ipintf = <{loop|Internet|LocalNetwork}]> [ethintf = <{bridge|RELAY|ethoa_8_35}]> [physintf = <{ethif1|ethif2|ethif3|ethif4| wlif1}]> where: mac_addr Host MAC address REQUIRED ip_addr Host IP address OPTIONAL
hostmgr Commands hostmgr clear Remove all hosts from list E-DOC-CTC-20071119-0014 v1.
hostmgr Commands hostmgr config Config hostmgr parameters SYNTAX: hostmgr config [state = <{disabled|enabled}]> [scantime = [autosave = <{disabled|enabled}]> [trace = <{disabled|enabled}]> where: state Enable/disable hostmgr deamon OPTIONAL scantime Time between two scans (sec) OPTIONAL autosave Enable/disable automatic saves to flash OPTIONAL trace Enable/disable hostmgr traces OPTIONAL 378 E-DOC-CTC-20071119-0014 v1.
hostmgr Commands hostmgr delete Delete host device info from hostmgr SYNTAX: hostmgr delete mac_addr = where: mac_addr E-DOC-CTC-20071119-0014 v1.
hostmgr Commands hostmgr flush Flushes hostmgr configuration (i.e. clean & to defaults) 380 E-DOC-CTC-20071119-0014 v1.
hostmgr Commands hostmgr list List all host devices SYNTAX: hostmgr list [expand = <{disabled|enabled}]> where: expand E-DOC-CTC-20071119-0014 v1.0 Expanded listing.
ids Commands 382 E-DOC-CTC-20071119-0014 v1.
ids Commands ids Commands ids clear Clear IDS statistics. see page 384 ids config Display/Modify IDS configuration. see page 385 ids parser list Display ids parser configuration. see page 386 ids parser modify Modify ids parser configuration. see page 387 ids pattern clear Reset pattern tracker. see page 388 ids pattern list Display patterns in pattern tracker. see page 389 ids pattern stats Display pattern tracker statistics.
ids Commands ids clear Clear IDS statistics. 384 E-DOC-CTC-20071119-0014 v1.
ids Commands ids config Display/Modify IDS configuration. SYNTAX: ids config [state = <{disabled|enabled}]> where: state E-DOC-CTC-20071119-0014 v1.0 Enable/Disable ids checks.
ids Commands ids parser list Display ids parser configuration. SYNTAX: ids parser list [parser = where: parser 386 The name of the parser. OPTIONAL E-DOC-CTC-20071119-0014 v1.
ids Commands ids parser modify Modify ids parser configuration. SYNTAX: ids parser modify [parser = state = <{disabled|enabled}> where: parser The name of the parser. OPTIONAL state The state of the parser. REQUIRED E-DOC-CTC-20071119-0014 v1.
ids Commands ids pattern clear Reset pattern tracker. 388 E-DOC-CTC-20071119-0014 v1.
ids Commands ids pattern list Display patterns in pattern tracker. SYNTAX: ids pattern list [size = <{10|100|full} or number]> where: size E-DOC-CTC-20071119-0014 v1.0 Modify the size of pattern tracker list.
ids Commands ids pattern stats Display pattern tracker statistics. 390 E-DOC-CTC-20071119-0014 v1.
ids Commands ids signature list Display ids signature configuration.
ids Commands ids signature modify Modify ids signature configuration.
ids Commands ids threshold clear Reset IDS thresholds. E-DOC-CTC-20071119-0014 v1.
ids Commands ids threshold list Display IDS thresholds. 394 E-DOC-CTC-20071119-0014 v1.
ids Commands ids threshold modify Modify IDS threshold. SYNTAX: ids threshold modify index = [window = [limit = [scaling = <{disabled|enabled}]> where: index The index of the threshold. REQUIRED window The time window of the threshold. OPTIONAL limit The limit of the threshold. OPTIONAL scaling Scaling of the threshold window. OPTIONAL E-DOC-CTC-20071119-0014 v1.
igmp Commands 396 E-DOC-CTC-20071119-0014 v1.
igmp Commands igmp Commands igmp host config Display/Modify global IGMP configuration. see page 398 igmp host debug clear Clear IGMP statistics. see page 399 igmp host debug stats Print IGMP statistics. see page 400 igmp host flush Flush the IGMP settings. see page 401 igmp host ifconfig Configure an IGMP interface. see page 402 igmp host iflist Show the configuration of the IGMP interfaces. see page 403 igmp host list Show the IGMP groups.
igmp Commands igmp host config Display/Modify global IGMP configuration. SYNTAX: igmp host config [requirera = <{disabled|enabled}]> where: requirera 398 Enable/Disable the router alert IP option check. OPTIONAL E-DOC-CTC-20071119-0014 v1.
igmp Commands igmp host debug clear Clear IGMP statistics. E-DOC-CTC-20071119-0014 v1.
igmp Commands igmp host debug stats Print IGMP statistics. 400 E-DOC-CTC-20071119-0014 v1.
igmp Commands igmp host flush Flush the IGMP settings. E-DOC-CTC-20071119-0014 v1.
igmp Commands igmp host ifconfig Configure an IGMP interface. SYNTAX: igmp host ifconfig intf = <{loop|Internet|LocalNetwork}> version = <{none|IGMPv1|IGMPv2|IGMPv3}> where: intf The IP interface name. REQUIRED version The IGMP version of the IP interface. REQUIRED 402 E-DOC-CTC-20071119-0014 v1.
igmp Commands igmp host iflist Show the configuration of the IGMP interfaces. SYNTAX: igmp host iflist [expand = <{disabled|enabled}]> where: expand E-DOC-CTC-20071119-0014 v1.0 Expanded listing.
igmp Commands igmp host list Show the IGMP groups. SYNTAX: igmp host list [intf = <{loop|Internet|LocalNetwork}]> [expand = <{disabled|enabled}]> where: intf The IP interface name. OPTIONAL expand Expanded listing. OPTIONAL 404 E-DOC-CTC-20071119-0014 v1.
igmp Commands igmp proxy config Configure the IGMP proxy. SYNTAX: igmp proxy config [state = <{disabled|enabled}]> [qi = [qri = [lmqi = [rv = [advinter = [initadvinter = [initadvcount = [requirera = <{disabled|enabled}]> [localgroup = <{disabled|enabled}]> where: state Enable/Disable the IGMP proxy. OPTIONAL qi The interval in seconds between general queries sent by the querier.
igmp Commands igmp proxy debug clear Clear IGMP proxy statistics 406 E-DOC-CTC-20071119-0014 v1.
igmp Commands igmp proxy debug stats Print IGMP proxy statistics E-DOC-CTC-20071119-0014 v1.
igmp Commands igmp proxy debug traceconfig Modify IGMP proxy trace configuration SYNTAX: igmp proxy debug traceconfig [state = <{disabled|enabled}]> where: state 408 Enable/Disable tracing. OPTIONAL E-DOC-CTC-20071119-0014 v1.
igmp Commands igmp proxy flush Flush all IGMP proxy settings and learned groups E-DOC-CTC-20071119-0014 v1.
igmp Commands igmp proxy grouplist Show the learned groups on an IGMP proxy interface. SYNTAX: igmp proxy grouplist [intf = <{LocalNetwork}]> [expand = <{disabled|enabled}]> where: intf The name of the IGMP proxy interface to be listed. OPTIONAL expand Expanded listing. OPTIONAL 410 E-DOC-CTC-20071119-0014 v1.
igmp Commands igmp proxy ifconfig Configure an IGMP proxy interface. SYNTAX: igmp proxy ifconfig intf = <{LocalNetwork|Internet}> [state = <{inactive|downstream|upstream}]> [version = <{IGMPv1|IGMPv2|IGMPv3}]> [fastleave = <{disabled|enabled}]> [exptrack = <{disabled|enabled}]> [mrd = <{disabled|enabled}]> where: intf The name of the IGMP proxy interface to be configured. REQUIRED state The state of the IGMP proxy interface. OPTIONAL version The IGMP version of the IGMP proxy interface.
igmp Commands igmp proxy iflist Show the configuration of an IGMP proxy interface. SYNTAX: igmp proxy iflist [expand = <{disabled|enabled}]> where: expand 412 Expanded listing. OPTIONAL E-DOC-CTC-20071119-0014 v1.
igmp Commands igmp proxy mbslist Show the IGMP proxy membership database (merge of all learned groups). E-DOC-CTC-20071119-0014 v1.
interface Command 414 E-DOC-CTC-20071119-0014 v1.
interface Command interface Command Display interfaces. SYNTAX: interface list [expand = <{disabled|enabled}]> [reverse = <{disabled|enabled}]> where: expand Expanded listing. OPTIONAL reverse Reverse listing (lower layer iso. upper layer). OPTIONAL E-DOC-CTC-20071119-0014 v1.
ip Commands 416 E-DOC-CTC-20071119-0014 v1.
ip Commands ip Commands ip arpadd Add an entry to the ARP cache of a broadcast IP interface. see page 419 ip arpdelete Delete an ARP entry. see page 420 ip arplist Display the ARP cache. see page 421 ip auto flush Flushes autoIP interfaces. see page 422 ip auto ifadd Creates a new autoIP interface. see page 423 ip auto ifattach Select and assign a link-local address to an autoIP interface. see page 424 ip auto ifconfig Configures an autoIP interface.
ip Commands ip ipadd Assign an IP address to an IP interface. see page 442 ip ipconfig Modify an IP address configuration. see page 443 ip ipdelete Remove an IP address from an IP interface. see page 444 ip iplist Display all configured IP addresses. see page 445 ip mcast flush Flush the multicast routing table. see page 446 ip mcast rtadd Add a multicast route to the multicast routing table. see page 447 ip mcast rtdelete Delete a multicast route from the multicast routing table.
ip Commands ip arpadd Add an entry to the ARP cache of a broadcast IP interface. SYNTAX: ip arpadd intf = <{LocalNetwork}> ip = [hwaddr = where: intf The IP interface name. REQUIRED ip The IP address [range] of the entry to add. REQUIRED hwaddr The hardware address (e.g. Ethernet MAC address) of the entry to add. OPTIONAL E-DOC-CTC-20071119-0014 v1.
ip Commands ip arpdelete Delete an ARP entry. SYNTAX: ip arpdelete intf = <{LocalNetwork}> ip = [hwaddr = where: intf The IP interface name. REQUIRED ip The IP address [range] of the entry to delete. REQUIRED hwaddr The hardware address (e.g. Ethernet MAC address) of the entry to delete. OPTIONAL 420 E-DOC-CTC-20071119-0014 v1.
ip Commands ip arplist Display the ARP cache. E-DOC-CTC-20071119-0014 v1.
ip Commands ip auto flush Flushes autoIP interfaces. 422 E-DOC-CTC-20071119-0014 v1.
ip Commands ip auto ifadd Creates a new autoIP interface. SYNTAX: ip auto ifadd intf = <{loop|Internet|LocalNetwork}> [addr = where: intf The name of the IP interface for which a linklocal address has to be allocated. REQUIRED addr The preferred link-local IP address. OPTIONAL E-DOC-CTC-20071119-0014 v1.
ip Commands ip auto ifattach Select and assign a link-local address to an autoIP interface. SYNTAX: ip auto ifattach intf = <> where: intf 424 The name of the autoIP interface. REQUIRED E-DOC-CTC-20071119-0014 v1.
ip Commands ip auto ifconfig Configures an autoIP interface. SYNTAX: ip auto ifconfig intf = <> [addr = [poolstart = [poolend = [netmask = [claim = [defence = [probe = [interval = where: intf The name of the autoIP interface to configure. REQUIRED addr The preferred link-local IP address.
ip Commands ip auto ifdelete Deletes an existing autoIP interface. SYNTAX: ip auto ifdelete intf = <> where: intf 426 The name of the autoIP interface. REQUIRED E-DOC-CTC-20071119-0014 v1.
ip Commands ip auto ifdetach Release the link-local address for the given autoIP interface. SYNTAX: ip auto ifdetach intf = <> where: intf E-DOC-CTC-20071119-0014 v1.0 The name of the autoIP interface.
ip Commands ip auto iflist Shows the autoIP interfaces. SYNTAX: ip auto iflist [intf = <]> where: intf 428 The name of a autoIP interface. OPTIONAL E-DOC-CTC-20071119-0014 v1.
ip Commands ip config Display/Modify global IP stack configuration.
ip Commands ip debug httpprobe Send HTTP probe to measure the round trip time taken to connect and access SYNTAX: ip debug httpprobe url = [version = <{1.0|1.1}]> where: url The Uniform Resource location identifying the HTTP server. REQUIRED version The version of the HTTP Server. OPTIONAL 430 E-DOC-CTC-20071119-0014 v1.
ip Commands ip debug sendto Send UDP packets. SYNTAX: ip debug sendto addr = [count = [size = [interval = [listen = <{disabled|enabled}]> [dffield = <{disabled|enabled}]> [srcaddr = [srcport = dstport = [dstintf = <{loop|Internet|LocalNetwork}]> where: addr The destination IP address. REQUIRED count The number of datagrams to send. OPTIONAL size The size of the datagram.
ip Commands ip debug stats Display statistics. SYNTAX: ip debug stats proto = <{ip|udp|tcp|icmp}> where: proto 432 The protocol for which to display the statistics. REQUIRED E-DOC-CTC-20071119-0014 v1.
ip Commands ip debug traceconfig Display/Modify IP stack trace configuration. SYNTAX: ip debug traceconfig [input = <{none|label|-telnet|-host|broadcast|all}]> [forward = <{none|label|-telnet|-host|broadcast|all}]> [output = <{none|label|-telnet|-host|broadcast|all}]> [drop = <{none|label|-telnet|-host|-broadcast| all}]> [path = <{none|label|-telnet|-host|-broadcast| all}]> [mode = <{line|dump}]> [arp = <{none|all}]> where: input Define the packets that will be traced.
ip Commands ip flush Flush all static IP parameters. Dynamic info (e.g. from PPP links) remains. 434 E-DOC-CTC-20071119-0014 v1.
ip Commands ip ifadd Create an IP interface. SYNTAX: ip ifadd intf = dest = <{ethoa_8_35}> where: intf An IP interface name. REQUIRED dest An network interface name. REQUIRED E-DOC-CTC-20071119-0014 v1.
ip Commands ip ifattach Attach an IP interface. SYNTAX: ip ifattach intf = <{}> where: intf 436 An IP interface name. REQUIRED E-DOC-CTC-20071119-0014 v1.
ip Commands ip ifconfig Modify an IP interface configuration. SYNTAX: ip ifconfig intf = <{loop|Internet|LocalNetwork}> [mtu = [status = <{down|up}]> [hwaddr = [group = <{wan|local|lan|tunnel|dmz|guest} or number]> [linksensing = <{disabled|enabled}]> [primary = <{disabled|enabled}]> [mcastpromisc = <{disabled|enabled}]> where: intf An IP interface name. REQUIRED mtu The maximum packet size (including IP header) to use on this interface.
ip Commands ip ifdelete Delete an IP interface. SYNTAX: ip ifdelete intf = <{LocalNetwork}> where: intf 438 An IP interface name. REQUIRED E-DOC-CTC-20071119-0014 v1.
ip Commands ip ifdetach Detach an IP interface. SYNTAX: ip ifdetach intf = <{loop|LocalNetwork}> where: intf E-DOC-CTC-20071119-0014 v1.0 An IP interface name.
ip Commands ip iflist Display all IP interfaces. SYNTAX: ip iflist [expand = <{disabled|enabled}]> where: expand 440 Expanded listing. OPTIONAL E-DOC-CTC-20071119-0014 v1.
ip Commands ip ifwait Wait for a status change of an IP interface. SYNTAX: ip ifwait intf = <{loop|Internet|LocalNetwork}> [timeout = [adminstatus = <{down|up}]> [operstatus = <{down|up}]> [linkstatus = <{down|up}]> where: intf An IP interface name. REQUIRED timeout The timeout in seconds. OPTIONAL adminstatus The administrative state of the interface. OPTIONAL operstatus The operational state of the interface. OPTIONAL linkstatus The link state of the interface.
ip Commands ip ipadd Assign an IP address to an IP interface. SYNTAX: ip ipadd intf = <{loop|Internet|LocalNetwork}> addr = [netmask = [pointopoint = [addroute = <{disabled|enabled}]> where: intf The IP interface name. REQUIRED addr The new IP address to add. REQUIRED netmask The subnetmask associated with this address. OPTIONAL pointopoint The remote address in case of a point-to-point link.
ip Commands ip ipconfig Modify an IP address configuration. SYNTAX: ip ipconfig addr = [preferred = <{disabled|enabled}]> [primary = <{disabled|enabled}]> where: addr The IP address to configure. REQUIRED preferred Make IP address the preferred address for that subnet. OPTIONAL primary Make IP address the primary address for the interface. OPTIONAL E-DOC-CTC-20071119-0014 v1.
ip Commands ip ipdelete Remove an IP address from an IP interface. SYNTAX: ip ipdelete addr = where: addr 444 The IP address to delete. REQUIRED E-DOC-CTC-20071119-0014 v1.
ip Commands ip iplist Display all configured IP addresses. E-DOC-CTC-20071119-0014 v1.
ip Commands ip mcast flush Flush the multicast routing table. 446 E-DOC-CTC-20071119-0014 v1.
ip Commands ip mcast rtadd Add a multicast route to the multicast routing table. SYNTAX: ip mcast rtadd srcintf = <{loop|Internet|LocalNetwork}> [src = grp = dstintf = <{loop|Internet|LocalNetwork}> [ttl = [ttlincr = <{disabled|enabled}]> where: srcintf The source IP interface. REQUIRED src The source IP address. OPTIONAL grp The multicast group IP address. REQUIRED dstintf The destination IP interface.
ip Commands ip mcast rtdelete Delete a multicast route from the multicast routing table. SYNTAX: ip mcast rtdelete srcintf = <{loop|Internet|LocalNetwork}> [src = grp = dstintf = <{loop|Internet|LocalNetwork}> where: srcintf The source IP interface. REQUIRED src The source IP address. OPTIONAL grp The multicast group IP address. REQUIRED dstintf The destination IP interface. REQUIRED 448 E-DOC-CTC-20071119-0014 v1.
ip Commands ip mcast rtlist Display the multicast routing table. SYNTAX: ip mcast rtlist [expand = <{disabled|enabled}]> where: expand E-DOC-CTC-20071119-0014 v1.0 Expanded listing.
ip Commands ip rtadd Add a route to the routing table. SYNTAX: ip rtadd dst = [dstmsk = [label = <{None|DSCP|Interactive|Management| Video|VoIP-RTP|VoIP-Signal|default}]> [gateway = [intf = <{loop|Internet|LocalNetwork}]> [srcintf = <{loop|Internet|LocalNetwork}]> [metric = where: dst The destination IP address(es) using this route. Supports ip/mask notation. REQUIRED dstmsk The destination IP address mask.
ip Commands ip rtdelete Delete a route from the routing table. SYNTAX: ip rtdelete dst = [dstmsk = [label = <{None|DSCP|Interactive|Management| Video|VoIP-RTP|VoIP-Signal|default}]> [gateway = [intf = <{loop|Internet|LocalNetwork}]> where: dst The destination IP address specification of the route to delete. Supports ip/mask notation. REQUIRED dstmsk The destination IP address mask. OPTIONAL label The name of a label.
ip Commands ip rtlist Display the routing table. SYNTAX: ip rtlist [expand = <{disabled|enabled}]> where: expand 452 Expanded listing. OPTIONAL E-DOC-CTC-20071119-0014 v1.
ipqos Commands ipqos Commands ipqos config Modify the IP QoS configuration for a given destination of an interface. see page 454 ipqos ef config Modify an IP QoS EF timer configuration for an interface. see page 455 ipqos ef list Display the IP QoS EF timers. see page 456 ipqos ef stats Display the IP QoS EF timer statistics. see page 457 ipqos list Display the IP QoS configuration. see page 458 ipqos queue clear Clear the IP QoS statistics.
ipqos Commands ipqos config Modify the IP QoS configuration for a given destination of an interface.
ipqos Commands ipqos ef config Modify an IP QoS EF timer configuration for an interface. SYNTAX: ipqos ef config intf = <{loop|Internet|LocalNetwork}> [state = <{disabled|enabled}]> [timeout = [mtu = where: intf The IP interface name. REQUIRED state Enable, disable IP QoS EF timer for the interface. OPTIONAL timeout The timeout in mili seconds. OPTIONAL mtu The MTU of the IP interface in case of EF data. OPTIONAL E-DOC-CTC-20071119-0014 v1.
ipqos Commands ipqos ef list Display the IP QoS EF timers. 456 E-DOC-CTC-20071119-0014 v1.
ipqos Commands ipqos ef stats Display the IP QoS EF timer statistics. E-DOC-CTC-20071119-0014 v1.
ipqos Commands ipqos list Display the IP QoS configuration. 458 E-DOC-CTC-20071119-0014 v1.
ipqos Commands ipqos queue clear Clear the IP QoS statistics. E-DOC-CTC-20071119-0014 v1.
ipqos Commands ipqos queue config Modify the IP QoS subqueue configuration. SYNTAX: ipqos queue config dest = <{atm_pvc_8_35}> queue = [propagate = <{disabled|enabled}]> [ecnmarking = <{disabled|enabled}]> [ackfiltering = <{disabled|enabled}]> [maxpackets = [maxbytes = [respackets = [resbytes = [hold = [markprob = where: dest The destination of the interface. Typically, a phonebook entry.
ipqos Commands ipqos queue list Display the IP QoS subqueue configuration. SYNTAX: ipqos queue list [dest = <{atm_pvc_8_35}]> where: dest E-DOC-CTC-20071119-0014 v1.0 The destination of the interface. Typically, a phonebook entry.
ipqos Commands ipqos queue stats Display the IP QoS subqueue statistics. SYNTAX: ipqos queue stats [dest = <{atm_pvc_8_35}]> where: dest 462 The destination of the interface. Typically, a phonebook entry. OPTIONAL E-DOC-CTC-20071119-0014 v1.
label Commands label Commands label add Add a label. see page 464 label chain add Add a chain. see page 465 label chain delete Delete a chain. see page 466 label chain flush Flush all chains. see page 467 label chain list Display a list of chains. see page 468 label delete Delete a label. see page 469 label flush Flush all label. see page 470 label list Display the labels. see page 471 label modify Modify a label configuration. see page 472 label rule add Add a rule.
label Commands label add Add a label. SYNTAX: label add name = where: name 464 The name of a label to add. REQUIRED E-DOC-CTC-20071119-0014 v1.
label Commands label chain add Add a chain. SYNTAX: label chain add chain = where: chain E-DOC-CTC-20071119-0014 v1.0 The name of the chain to add.
label Commands label chain delete Delete a chain. SYNTAX: label chain delete chain = where: chain 466 The name of the chain to delete. REQUIRED E-DOC-CTC-20071119-0014 v1.
label Commands label chain flush Flush all chains. E-DOC-CTC-20071119-0014 v1.
label Commands label chain list Display a list of chains. SYNTAX: label chain list [format = <{pretty|cli}]> where: format 468 The format of the chain list. OPTIONAL E-DOC-CTC-20071119-0014 v1.
label Commands label delete Delete a label. SYNTAX: label delete name = <{DSCP|Interactive|Management|Video| VoIP-RTP|VoIP-Signal|default}> where: name E-DOC-CTC-20071119-0014 v1.0 The name of a label.
label Commands label flush Flush all label. 470 E-DOC-CTC-20071119-0014 v1.
label Commands label list Display the labels. SYNTAX: label list [name = <{DSCP|Interactive|Management|Video| VoIP-RTP|VoIP-Signal|default}]> where: name E-DOC-CTC-20071119-0014 v1.0 The name of a label.
label Commands label modify Modify a label configuration.
label Commands label rule add Add a rule.
label Commands label rule delete Delete a rule. SYNTAX: label rule delete chain = index = where: chain The name of the chain in which to delete the rule. REQUIRED index The number of the rule in the chain. REQUIRED 474 E-DOC-CTC-20071119-0014 v1.
label Commands label rule flush Flush all rules. SYNTAX: label rule flush [chain = where: chain E-DOC-CTC-20071119-0014 v1.0 The name of the chain to flush.
label Commands label rule list Display a list of rules. SYNTAX: label rule list [chain = [format = <{pretty|cli}]> where: chain The name of the chain to list the rules of. OPTIONAL format The format of the rule list. OPTIONAL 476 E-DOC-CTC-20071119-0014 v1.
label Commands label rule modify Modify a rule. SYNTAX: label rule modify chain = [index = [newindex = [name = [clink = [[!]srcintf] = [[!]srcip] = [[!]dstip] = [[!]serv] = [log = <{disabled|enabled}]> [state = <{disabled|enabled}]> [label = <{None|link|DSCP|Interactive| Management|Video|VoIP-RTP|VoIP-Signal| default}]> where: chain The name of the chain which contains the rule.
language Commands 478 E-DOC-CTC-20071119-0014 v1.
language Commands language Commands language config Select a language. see page 480 language delete Delete one or all language archives. see page 481 language list List available languages archives. see page 482 E-DOC-CTC-20071119-0014 v1.
language Commands language config Select a language. SYNTAX: language config [language = [complete = <{yes|no}]> where: language Language code : OSI language code (2 chars) for language (en=English) OPTIONAL complete Enable translation for expert pages. OPTIONAL 480 E-DOC-CTC-20071119-0014 v1.
language Commands language delete Delete one or all language archives. SYNTAX: language delete [file = [all = <{yes|no}]> where: file Filename : name of language archive to delete OPTIONAL all Deletes all languages archives. OPTIONAL E-DOC-CTC-20071119-0014 v1.
language Commands language list List available languages archives. 482 E-DOC-CTC-20071119-0014 v1.
mbus Commands mbus Commands mbus client authenticate Authenticate a session see page 484 mbus client config Modify client parameters see page 485 mbus client exec Execute mbus command see page 486 mbus client register Register cli client to mbus see page 488 mbus client termsession Terminate a session see page 489 mbus client unregister Unregister cli client from mbus see page 490 mbus debug clearstats Reset mbus statistics.
mbus Commands mbus client authenticate Authenticate a session SYNTAX: mbus client authenticate type = <{cleartext|md5|crypt|digest}> username = password = where: type Authentication type REQUIRED username User name REQUIRED password password REQUIRED 484 E-DOC-CTC-20071119-0014 v1.
mbus Commands mbus client config Modify client parameters SYNTAX: mbus client config [writelock = <{enabled|disabled}]> [wlgetimeout = [wlidletimeout = [path = [type = <{indexpath|objidpath|keystrpath}]> [id = where: writelock Get/release mbus writelock OPTIONAL wlgetimeout Writelock get timeout in seconds (forever=-1, *default=nowait=0) OPTIONAL wlidletimeout Writelock idle timeout in seconds (forever=-1, *default=30) OPTIONAL path Fully qualified
mbus Commands mbus client exec Execute mbus command SYNTAX: mbus client exec cmd = <{getpath|getcount|getnames|getvalues| setvalue|addobject|deleteobject|subscribe| unsubscribe|getaccessrights|setaccessrights}> [param = [value = [gettype = <{parameter|path|object}]> [depth = [processcmd = <{enabled|disabled}]> [onerrorrollback = <{enabled|disabled}]> [usecallback = <{enabled|disabled}]> [filter = [path = [flags = <[+/-]flag[+/-f
mbus Commands =, <, <=, >, >=, and, or, not. The left operand is a parameter name. The right operand is a parameter value. For boolean operators the operands are filters. Example: '(== Name eth0)'.
mbus Commands mbus client register Register cli client to mbus SYNTAX: mbus client register [dmtree = <{igd|atomic|system}]> [type = <{indexpath|objidpath|keystrpath}]> [dlink = <{local_ipc|remote_inet}]> [mbusd_addr = [refresolv = <{disabled|enabled}]> where: dmtree Select mbusd datamodel tree.
mbus Commands mbus client termsession Terminate a session SYNTAX: mbus client termsession id = where: id E-DOC-CTC-20071119-0014 v1.
mbus Commands mbus client unregister Unregister cli client from mbus 490 E-DOC-CTC-20071119-0014 v1.
mbus Commands mbus debug clearstats Reset mbus statistics. E-DOC-CTC-20071119-0014 v1.
mbus Commands mbus debug loadobjects Load/sync object instances from plugins SYNTAX: mbus debug loadobjects [dmtree = <{igd|atomic|system}]> [path = [type = <{indexpath|objidpath|keystrpath}]> [flush = <{disabled|enabled}]> where: dmtree Select mbusd datamodel tree. OPTIONAL path Fully qualified mbus path OPTIONAL type Path type (default = indexpath OPTIONAL flush Flush objects before load (default=disabled) OPTIONAL 492 E-DOC-CTC-20071119-0014 v1.
mbus Commands mbus debug stats Display mbus statistics. E-DOC-CTC-20071119-0014 v1.
mbus Commands mbus debug traceconfig Modify mbus trace settings. SYNTAX: mbus debug traceconfig [level = where: level 494 Select mbus trace level (0-4). OPTIONAL E-DOC-CTC-20071119-0014 v1.
mbus Commands mbus debug unloadobjects Unload object instances SYNTAX: mbus debug unloadobjects [dmtree = <{igd|atomic|system}]> [path = [type = <{indexpath|objidpath|keystrpath}]> [flush = <{disabled|enabled}]> where: dmtree Select mbusd datamodel tree. OPTIONAL path Fully qualified mbus path OPTIONAL type Path type OPTIONAL flush Flush objects before load (default=disabled) OPTIONAL E-DOC-CTC-20071119-0014 v1.
mbus Commands mbus listcontexts Display the context instances SYNTAX: mbus listcontexts [dmtree = <{igd|atomic|system}]> [expand = <{disabled|enabled}]> where: dmtree Select mbusd datamodel tree. OPTIONAL expand Details enabled/disabled OPTIONAL 496 E-DOC-CTC-20071119-0014 v1.
mbus Commands mbus listenums Display the registered enumtypes SYNTAX: mbus listenums [dmtree = <{igd|atomic|system}]> [name = [expand = <{disabled|enabled}]> where: dmtree Select mbusd datamodel tree. OPTIONAL name Filter enumtypes by (part of) the name OPTIONAL expand Details enabled/disabled OPTIONAL E-DOC-CTC-20071119-0014 v1.
mbus Commands mbus listobjects Display the object instances SYNTAX: mbus listobjects [dmtree = <{igd|atomic|system}]> [path = [type = <{indexpath|objidpath|keystrpath}]> [output = <{tree|list}]> [showflags = <{disabled|enabled}]> where: dmtree Select mbusd datamodel tree. OPTIONAL path Fully qualified mbus path to list.
mbus Commands mbus listsubscriptions Display the subscription instances SYNTAX: mbus listsubscriptions [dmtree = <{igd|atomic|system}]> where: dmtree E-DOC-CTC-20071119-0014 v1.0 Select mbusd datamodel tree.
mbus Commands mbus listtypes Display the registered objecttypes SYNTAX: mbus listtypes [dmtree = <{igd|atomic|system}]> [path = [expand = <{disabled|enabled}]> where: dmtree Select mbusd datamodel tree. OPTIONAL path Fully qualified mbus path to list. OPTIONAL expand Details enabled/disabled OPTIONAL 500 E-DOC-CTC-20071119-0014 v1.
mbus Commands mbus pluginevent Simulate event from plugin SYNTAX: mbus pluginevent ctxid = type = <{addobj|delobj|updobj}> path = [name = [value = [orivalue = where: ctxid Plugin context id REQUIRED type Event type REQUIRED path Plugin event subpath REQUIRED name Plugin event name OPTIONAL value Plugin event value OPTIONAL orivalue Plugin event orivalue OPTIONAL E-DOC-CTC-20071119-0014 v1.
mbus Commands mbus unregister Unregister a client/plugin context SYNTAX: mbus unregister id = where: id 502 Select message-based client/plugin context id. REQUIRED E-DOC-CTC-20071119-0014 v1.
memm Commands memm Commands memm debug clearstats Clear time statistics. see page 504 memm debug lock stats Display lock statistics. see page 505 memm debug lock traceconfig Modify lock trace settings. see page 506 memm debug stats Display memm time statistics. see page 507 memm debug tag (Un)tag memory manager objects. see page 508 memm debug traceconfig Modify memm trace settings. see page 509 memm listobjects Display objects. see page 510 memm stats Display memm statistics.
memm Commands memm debug clearstats Clear time statistics. 504 E-DOC-CTC-20071119-0014 v1.
memm Commands memm debug lock stats Display lock statistics. E-DOC-CTC-20071119-0014 v1.
memm Commands memm debug lock traceconfig Modify lock trace settings. SYNTAX: memm debug lock traceconfig [level = [name = where: level Select memm trace level (0-4). OPTIONAL name application name filter for lock traces (empty displays all lock traces) OPTIONAL 506 E-DOC-CTC-20071119-0014 v1.
memm Commands memm debug stats Display memm time statistics. SYNTAX: memm debug stats [name = where: name E-DOC-CTC-20071119-0014 v1.
memm Commands memm debug tag (Un)tag memory manager objects. SYNTAX: memm debug tag [name = [tag = <{enabled|disabled}]> where: name Select typename(s) to list (supports partial typename) OPTIONAL tag Set (or unset) the tag OPTIONAL 508 E-DOC-CTC-20071119-0014 v1.
memm Commands memm debug traceconfig Modify memm trace settings. SYNTAX: memm debug traceconfig [level = where: level E-DOC-CTC-20071119-0014 v1.0 Select memm trace level (0-4).
memm Commands memm listobjects Display objects. SYNTAX: memm listobjects [name = [tagged = <{no|yes}]> [hidedeldynstr = <{no|yes}]> where: name Select typename(s) to list (supports partial typename) OPTIONAL tagged Show only tagged (yes) or untagged (no) objects OPTIONAL hidedeldynstr Hide (yes) / show (no) deleted dynstrings (default = show) OPTIONAL 510 E-DOC-CTC-20071119-0014 v1.
memm Commands memm stats Display memm statistics. SYNTAX: memm stats [name = where: name E-DOC-CTC-20071119-0014 v1.
menu Command 512 E-DOC-CTC-20071119-0014 v1.
menu Command menu Command Displays menu E-DOC-CTC-20071119-0014 v1.
mlp Commands 514 E-DOC-CTC-20071119-0014 v1.
mlp Commands mlp Commands mlp debug export Export all scores. see page 516 mlp debug stats Display mlp statisctics. see page 517 mlp debug traceconfig Modify mlp trace settings. see page 518 mlp flush Flush all mlp structures. see page 519 mlp import Import all scores. see page 520 mlp privilege add Add a privilege. see page 521 mlp privilege addzone Add a zone to a privilege. see page 522 mlp privilege config Modify the privilege.
mlp Commands mlp debug export Export all scores. 516 E-DOC-CTC-20071119-0014 v1.
mlp Commands mlp debug stats Display mlp statisctics. E-DOC-CTC-20071119-0014 v1.
mlp Commands mlp debug traceconfig Modify mlp trace settings. SYNTAX: mlp debug traceconfig [trace = <{disabled|enabled|full}]> where: trace 518 Select mlp trace level. OPTIONAL E-DOC-CTC-20071119-0014 v1.
mlp Commands mlp flush Flush all mlp structures. E-DOC-CTC-20071119-0014 v1.
mlp Commands mlp import Import all scores. SYNTAX: mlp import [trace = <{disabled|enabled|full}]> where: trace 520 Select import trace level. OPTIONAL E-DOC-CTC-20071119-0014 v1.
mlp Commands mlp privilege add Add a privilege. SYNTAX: mlp privilege add name = type = <{access|service}> [descr = where: name Privilege name. REQUIRED type Privilege type. REQUIRED descr Privilege description. OPTIONAL E-DOC-CTC-20071119-0014 v1.
mlp Commands mlp privilege addzone Add a zone to a privilege.
mlp Commands mlp privilege config Modify the privilege. SYNTAX: mlp privilege config name = <> [descr = [score = <{hex-word}[:{hex-word}] ex: 'a12:c30f']> where: name Select the privilege by name. REQUIRED descr Set the description. OPTIONAL score Set the score. OPTIONAL E-DOC-CTC-20071119-0014 v1.
mlp Commands mlp privilege delete Delete a privilege. SYNTAX: mlp privilege delete name = <> where: name 524 Privilege name. REQUIRED E-DOC-CTC-20071119-0014 v1.
mlp Commands mlp privilege list Display the privileges. SYNTAX: mlp privilege list [name = <]> [type = <{access|service}]> [verbose = <{minimal|medium|all}]> where: name Privilege name. OPTIONAL type Privilege type. OPTIONAL verbose Limit the output list. OPTIONAL E-DOC-CTC-20071119-0014 v1.
mlp Commands mlp privilege removezone Remove a zone from a privilege.
mlp Commands mlp role add Add a role. SYNTAX: mlp role add name = parent = <> [descr = where: name Role name. REQUIRED parent Parent role name. REQUIRED descr Role description. OPTIONAL E-DOC-CTC-20071119-0014 v1.
mlp Commands mlp role addpriv Add a privilege. SYNTAX: mlp role addpriv name = <{Administrator|LAN_Admin|PowerUser| root|SuperUser|TechnicalSupport|User| WAN_Admin}> access = <{anyaccess|AP1|AP2|AP3|AP4|AP5|AP6| AP7|AP8|AP9}> service = <{anyservice|SP1|SP10|SP11|SP12| SP13|SP14|SP15|SP16|SP17|SP18|SP19|SP2|SP3| SP4|SP5|SP6|SP7|SP8|SP9}> where: name Role name. REQUIRED access Access privilege to add. REQUIRED service Privilege name to add. REQUIRED 528 E-DOC-CTC-20071119-0014 v1.
mlp Commands mlp role config Modify the role. SYNTAX: mlp role config name = <> [parent = <]> [descr = where: name Role name. REQUIRED parent Parent role name. OPTIONAL descr Role description. OPTIONAL E-DOC-CTC-20071119-0014 v1.
mlp Commands mlp role delete Delete a role. SYNTAX: mlp role delete name = <> where: name 530 Role name. REQUIRED E-DOC-CTC-20071119-0014 v1.
mlp Commands mlp role list Display the roles. SYNTAX: mlp role list [name = <]> [verbose = <{minimal|medium|all}]> where: name Role name. OPTIONAL verbose Limit the output list. OPTIONAL E-DOC-CTC-20071119-0014 v1.
mlp Commands mlp role removepriv Remove a privilege. SYNTAX: mlp role removepriv name = <> access = <> [service = <]> where: name Role name. REQUIRED access Access privilege to delete. REQUIRED service Privilege name to delete. OPTIONAL 532 E-DOC-CTC-20071119-0014 v1.
nat Commands nat Commands nat config Modify global NAT configuration. see page 534 nat flush Flush current NAT configuration. see page 535 nat ifconfig Modify address translation on an IP interface. see page 536 nat iflist Display all interfaces. see page 537 nat mapadd Add an address mapping to a nat enabled interface. see page 538 nat mapdelete Delete an address mapping from a nat enabled interface. see page 539 nat maplist Display address mappings.
nat Commands nat config Modify global NAT configuration. SYNTAX: nat config [trace = <{disabled|enabled}]> where: trace 534 Enable/disable traces. OPTIONAL E-DOC-CTC-20071119-0014 v1.
nat Commands nat flush Flush current NAT configuration. E-DOC-CTC-20071119-0014 v1.
nat Commands nat ifconfig Modify address translation on an IP interface. SYNTAX: nat ifconfig intf = <{loop|Internet|LocalNetwork}> translation = <{disabled|enabled|transparent}> where: intf The IP interface name. REQUIRED translation Disabled, enabled or tranparent address translation. REQUIRED 536 E-DOC-CTC-20071119-0014 v1.
nat Commands nat iflist Display all interfaces. E-DOC-CTC-20071119-0014 v1.
nat Commands nat mapadd Add an address mapping to a nat enabled interface.
nat Commands nat mapdelete Delete an address mapping from a nat enabled interface. SYNTAX: nat mapdelete intf = <{loop|Internet|LocalNetwork}> index = where: intf The IP interface name. REQUIRED index The map index as listed by ':nat maplist'. REQUIRED E-DOC-CTC-20071119-0014 v1.
nat Commands nat maplist Display address mappings. SYNTAX: nat maplist [intf = <{loop|Internet|LocalNetwork}]> [expand = <{disabled|enabled}]> where: intf The IP interface name. OPTIONAL expand Expanded listing. OPTIONAL 540 E-DOC-CTC-20071119-0014 v1.
nat Commands nat tmpladd Add an address mapping template.
nat Commands weight 542 The weight to be used for the template instance(s). OPTIONAL E-DOC-CTC-20071119-0014 v1.
nat Commands nat tmpldelete Delete an address mapping template. SYNTAX: nat tmpldelete index = where: index E-DOC-CTC-20071119-0014 v1.0 The template index as listed by ':nat tmpllist'.
nat Commands nat tmplinst Instantiate address mapping templates for a given dynamic address. SYNTAX: nat tmplinst intf = <{loop|Internet|LocalNetwork}> addr_index = dynamic_addr = where: intf The IP interface name. REQUIRED addr_index The outside IP address index/key to instantiate for. REQUIRED dynamic_addr The dynamic address to substitute the index/key with. REQUIRED 544 E-DOC-CTC-20071119-0014 v1.
nat Commands nat tmpllist Display address mapping templates. SYNTAX: nat tmpllist [expand = <{disabled|enabled}]> where: expand E-DOC-CTC-20071119-0014 v1.0 Expanded listing.
ping Command 546 E-DOC-CTC-20071119-0014 v1.
ping Command ping Command Send ICMP ECHO_REQUEST packets. SYNTAX: ping proto = <{ip|atm}> addr = dest = <{atm_pvc_8_35}> [count = [size = [interval(ms) = [DF-bit = <{disabled|enabled}]> [srcaddr = where: proto The interface type to be used. REQUIRED addr The destination IP address. REQUIRED dest The destination address for the request. REQUIRED count The number of pings to send (0 is continuous ping).
ppp Commands 548 E-DOC-CTC-20071119-0014 v1.
ppp Commands ppp Commands ppp flush Flush all PPP interfaces. see page 550 ppp ifadd Create a new PPP interface. see page 551 ppp ifattach Attach a PPP interface. see page 552 ppp ifconfig Modify a PPP interface. see page 553 ppp ifdelete Delete a PPP interface. see page 556 ppp ifdetach Detach a PPP interface. see page 557 ppp iflist Display the PPP interfaces. see page 558 ppp ifscan Scan a PPP interface for available interfaces.
ppp Commands ppp flush Flush all PPP interfaces. 550 E-DOC-CTC-20071119-0014 v1.
ppp Commands ppp ifadd Create a new PPP interface. SYNTAX: ppp ifadd intf = where: intf E-DOC-CTC-20071119-0014 v1.0 The name for the new PPP interface. If not specified, the destination will double as interface name.
ppp Commands ppp ifattach Attach a PPP interface. SYNTAX: ppp ifattach intf = <{Internet}> where: intf 552 The name of the PPP interface. REQUIRED E-DOC-CTC-20071119-0014 v1.
ppp Commands ppp ifconfig Modify a PPP interface.
ppp Commands servicename The service name for a PPP session. OPTIONAL pool Acquire IP subnet and assign it to a free DHCP pool. OPTIONAL pcomp Try to negotiate PPP protocol compression (LCP PCOMP). OPTIONAL accomp Try to negotiate PPP address & control field compression (LCP ACCOMP). OPTIONAL trace Enable verbose console logging. OPTIONAL concentrator The access concentrator is on this side of the PPP connection. OPTIONAL auth Authentication protocol to be used.
ppp Commands dnsmetric DNS route metric to be used for the negotiated DNS servers. OPTIONAL idletime Maximum time the link may be idle (seconds). OPTIONAL idletrigger Consider the link being idle if no traffic is sent and/or received during the idle time. OPTIONAL unnumbered Take local IP address from 'laddr' field and remote IP address from the pool. SVC only. OPTIONAL E-DOC-CTC-20071119-0014 v1.
ppp Commands ppp ifdelete Delete a PPP interface. SYNTAX: ppp ifdelete intf = <{Internet}> where: intf 556 The name of the PPP interface. REQUIRED E-DOC-CTC-20071119-0014 v1.
ppp Commands ppp ifdetach Detach a PPP interface. SYNTAX: ppp ifdetach intf = <{}> where: intf E-DOC-CTC-20071119-0014 v1.0 The name of the PPP interface.
ppp Commands ppp iflist Display the PPP interfaces. SYNTAX: ppp iflist [intf = <{Internet}]> where: intf 558 The name of a PPP interface. OPTIONAL E-DOC-CTC-20071119-0014 v1.
ppp Commands ppp ifscan Scan a PPP interface for available interfaces. SYNTAX: ppp ifscan intf = <{Internet}> [time = where: intf The name of the PPP interface to scan. REQUIRED time The time to scan for services (in seconds). OPTIONAL E-DOC-CTC-20071119-0014 v1.
ppp Commands ppp relay flush Remove all ethernet interfaces from the PPP relay agent list and terminate all 560 E-DOC-CTC-20071119-0014 v1.
ppp Commands ppp relay ifadd Add an ethernet interface to the PPP relay list. SYNTAX: ppp relay ifadd intf = <{}> where: intf E-DOC-CTC-20071119-0014 v1.0 The ethernet intf to be added to the PPP relay agent list.
ppp Commands ppp relay ifconfig Modify an ethernet interface from the PPP relay agent list. SYNTAX: ppp relay ifconfig intf = <{bridge|ethoa_8_35}> hwaddr = where: intf The ethernet intf to be added to the PPP relay agent list. REQUIRED hwaddr The hardware address (e.g. Ethernet MAC address) of this interface. REQUIRED 562 E-DOC-CTC-20071119-0014 v1.
ppp Commands ppp relay ifdelete Delete an ethernet interface from the PPP relay agent list. SYNTAX: ppp relay ifdelete intf = <{bridge|ethoa_8_35}> where: intf E-DOC-CTC-20071119-0014 v1.0 The ethernet intf to be added to the PPP relay agent list.
ppp Commands ppp relay iflist Display all ethernet interfaces added to the PPP relay agent list. 564 E-DOC-CTC-20071119-0014 v1.
ppp Commands ppp relay sesslist Display all active PPP relay sessions. E-DOC-CTC-20071119-0014 v1.
ppp Commands ppp rtadd Add a route to the routing table when PPP link comes up. SYNTAX: ppp rtadd intf = <{Internet}> dst = [dstmsk = [label = <{None|DSCP|Interactive|Management| Video|VoIP-RTP|VoIP-Signal|default}]> [src = [srcmsk = [metric = where: intf The name of a PPP interface. REQUIRED dst The IP destination address specification for the route to be added when the link comes up.
ppp Commands ppp rtdelete Delete the route for a PPP link. SYNTAX: ppp rtdelete intf = <{Internet}> where: intf E-DOC-CTC-20071119-0014 v1.0 The PPP interface name for which to delete the route settings.
pptp Commands 568 E-DOC-CTC-20071119-0014 v1.
pptp Commands pptp Commands pptp flush Flushes the PPTP configuration. see page 570 pptp ifadd Adds a PPTP profile (backwards compatible with previous release, use profiles see page 571 pptp list Shows PPTP configuration. see page 572 pptp profadd Defines a new PPTP profile. see page 573 pptp profdelete Deletes a PPTP profile. see page 574 pptp proflist Lists PPTP profiles. see page 575 E-DOC-CTC-20071119-0014 v1.
pptp Commands pptp flush Flushes the PPTP configuration. 570 E-DOC-CTC-20071119-0014 v1.
pptp Commands pptp ifadd Adds a PPTP profile (backwards compatible with previous release, use profiles SYNTAX: pptp ifadd dest = [rate = [encaps = <{vcmux|nlpid}]> [ac = <{never|always|keep}]> where: dest The WAN destination for this PPTP tunnel. Typically a phonebook name. REQUIRED rate Transmit speed in kbits/s for the WAN link. OPTIONAL encaps The WAN protocol encapsulation. OPTIONAL ac Enable/disable sending address and control field (0xFF03) on the WAN link.
pptp Commands pptp list Shows PPTP configuration. 572 E-DOC-CTC-20071119-0014 v1.
pptp Commands pptp profadd Defines a new PPTP profile. SYNTAX: pptp profadd name = [qos = <{default}]> [encaps = <{vcmux|nlpid}]> [ac = <{never|always|keep}]> where: name The name for the new PPTP profile. REQUIRED qos The name of the qosbook entry, containing the settings for this profile. OPTIONAL encaps The WAN protocol encapsulation to be used with this profile. OPTIONAL ac Enable/disable sending address and control field (0xFF03) on the WAN link.
pptp Commands pptp profdelete Deletes a PPTP profile. SYNTAX: pptp profdelete name = <> where: name 574 The name of the profile to delete. REQUIRED E-DOC-CTC-20071119-0014 v1.
pptp Commands pptp proflist Lists PPTP profiles. E-DOC-CTC-20071119-0014 v1.
ra Commands 576 E-DOC-CTC-20071119-0014 v1.
ra Commands ra Commands ra config Configure remote access parameters. see page 578 ra start Starts temporary mode. see page 579 ra stop Stops temporary mode. see page 580 E-DOC-CTC-20071119-0014 v1.
ra Commands ra config Configure remote access parameters. SYNTAX: ra config [state = <{disabled|enabled}]> [secure = <{enabled|disabled}]> [port = [timeout = [mode = <{Permanent|Temporary}]> [ipintf = [randompassword = <{enabled|disabled}]> [randomport = <{enabled|disabled}]> [group = [user = where: state Enable/disable RAD. OPTIONAL secure Use secure mode (https). OPTIONAL port The port number. OPTIONAL timeout The timeout value.
ra Commands ra start Starts temporary mode. E-DOC-CTC-20071119-0014 v1.
ra Commands ra stop Stops temporary mode. 580 E-DOC-CTC-20071119-0014 v1.
saveall Command saveall Command Saves current configuration. E-DOC-CTC-20071119-0014 v1.
script Commands 582 E-DOC-CTC-20071119-0014 v1.
script Commands script Commands script add Add line to script. see page 584 script delete Delete complete script or line from script. see page 585 script flush Flush scripts. see page 586 script list List script. see page 587 script run Run script. see page 588 E-DOC-CTC-20071119-0014 v1.
script Commands script add Add line to script. SYNTAX: script add name = [index = command = where: name Name of script. REQUIRED index Line number (0 = add). OPTIONAL command Command. REQUIRED 584 E-DOC-CTC-20071119-0014 v1.
script Commands script delete Delete complete script or line from script. SYNTAX: script delete name = <{autopvc_add_qos|autopvc_delete_qos| autopvc_add_bridge|autopvc_delete_pppoerelay| autopvc_add_ipoa|autopvc_delete_ipoa| autopvc_add_ethoa|autopvc_delete_ethoa| autopvc_add_pppoa|autopvc_delete_pppoa| autopvc_add_pppoe|autopvc_delete_pppoe| autopvc_change_qos|wlbrintfadd|wlbrintfdel}> [index = where: name Name of script. REQUIRED index Line number. OPTIONAL E-DOC-CTC-20071119-0014 v1.
script Commands script flush Flush scripts. 586 E-DOC-CTC-20071119-0014 v1.
script Commands script list List script. SYNTAX: script list [name = <{autopvc_add_qos|autopvc_delete_qos| autopvc_add_bridge|autopvc_delete_pppoerelay| autopvc_add_ipoa|autopvc_delete_ipoa| autopvc_add_ethoa|autopvc_delete_ethoa| autopvc_add_pppoa|autopvc_delete_pppoa| autopvc_add_pppoe|autopvc_delete_pppoe| autopvc_change_qos|wlbrintfadd|wlbrintfdel}]> where: name E-DOC-CTC-20071119-0014 v1.0 Name of script.
script Commands script run Run script. SYNTAX: script run name = <{autopvc_add_qos|autopvc_delete_qos| autopvc_add_bridge|autopvc_delete_pppoerelay| autopvc_add_ipoa|autopvc_delete_ipoa| autopvc_add_ethoa|autopvc_delete_ethoa| autopvc_add_pppoa|autopvc_delete_pppoa| autopvc_add_pppoe|autopvc_delete_pppoe| autopvc_change_qos|wlbrintfadd|wlbrintfdel}> pars = where: name Name of script. REQUIRED pars Parameters separated with comma e.q. a,b,c . REQUIRED 588 E-DOC-CTC-20071119-0014 v1.
service Commands service Commands service host add Add a service. see page 590 service host assign Assign a service to a host. see page 591 service host delete Delete a service. see page 592 service host disable Disable a service. see page 593 service host flush Flush all services. see page 594 service host list Display list of services. see page 595 service host rule add Create/define service portmap. see page 596 service host rule delete Delete a service portmap.
service Commands service host add Add a service. SYNTAX: service host add name = [mode = <{server|client|custom}]> where: name The name of the service. REQUIRED mode server, client or custom service ? OPTIONAL 590 E-DOC-CTC-20071119-0014 v1.
service Commands service host assign Assign a service to a host. SYNTAX: service host assign name = <{ABC (Another Bittorent Client)|Age of Empires|Age of Mythology|AIM BitTorrent| Black and White|Call of Duty|Call of Duty - UnitedOffensive|CarbonCopy32|Castle Wolfenstein|Championship Manager 03-04| Checkpoint FW1 VPN|Command and Conquer Generals|Command and ConquerZero Hour|Counter Strike|Cu-SeeMe Cornell|Cu-SeeMe White Pine 3.1.2and 4.
service Commands service host delete Delete a service. SYNTAX: service host delete name = <{ABC (Another Bittorent Client)|Age of Empires|Age of Mythology|AIM BitTorrent| Black and White|Call of Duty|Call of Duty - UnitedOffensive|CarbonCopy32|Castle Wolfenstein|Championship Manager 03-04| Checkpoint FW1 VPN|Command and Conquer Generals|Command and ConquerZero Hour|Counter Strike|Cu-SeeMe Cornell|Cu-SeeMe White Pine 3.1.2and 4.
service Commands service host disable Disable a service. SYNTAX: service host disable [name = <{ABC (Another Bittorent Client)| Age of Empires|Age of Mythology|BearShare| BitTorrent|Black and White|Call of Duty| Call of Duty -United Offensive|CarbonCopy32| Castle Wolfenstein|ChampionshipManager 03-04| Checkpoint FW1 VPN|Command and Conquer Generals|Command and Conquer Zero Hour| Counter Strike|Cu-SeeMe Cornell|Cu-SeeMe White Pine 3.1.2 and 4.
service Commands service host flush Flush all services. 594 E-DOC-CTC-20071119-0014 v1.
service Commands service host list Display list of services. SYNTAX: service host list [name = <{ABC (Another Bittorent Client)| Age of Empires|Age of Mythology|BearShare| BitTorrent|Black and White|Call of Duty| Call of Duty -United Offensive|CarbonCopy32| Castle Wolfenstein|ChampionshipManager 03-04| Checkpoint FW1 VPN|Command and Conquer Generals|Command and Conquer Zero Hour| Counter Strike|Cu-SeeMe Cornell|Cu-SeeMe White Pine 3.1.2 and 4.
service Commands service host rule add Create/define service portmap. SYNTAX: service host rule add name = <{ABC (Another Bittorent Client)|Age of Empires|Age of Mythology|AIM BitTorrent| Black and White|Call of Duty|Call of Duty - UnitedOffensive|CarbonCopy32|Castle Wolfenstein|Championship Manager 03-04| Checkpoint FW1 VPN|Command and Conquer Generals|Command and ConquerZero Hour|Counter Strike|Cu-SeeMe Cornell|Cu-SeeMe White Pine 3.1.2and 4.
service Commands triggerport Defines outbound trigger port. OPTIONAL triggerprotocol Protocol of the trigger port. OPTIONAL E-DOC-CTC-20071119-0014 v1.
service Commands service host rule delete Delete a service portmap. SYNTAX: service host rule delete name = <{ABC (Another Bittorent Client)|Age of Empires|Age of Mythology|AIM BitTorrent| Black and White|Call of Duty|Call of Duty - UnitedOffensive|CarbonCopy32|Castle Wolfenstein|Championship Manager 03-04| Checkpoint FW1 VPN|Command and Conquer Generals|Command and ConquerZero Hour|Counter Strike|Cu-SeeMe Cornell|Cu-SeeMe White Pine 3.1.2and 4.
service Commands triggerport Defines outbound trigger port. OPTIONAL triggerprotocol Protocol of the trigger port. OPTIONAL E-DOC-CTC-20071119-0014 v1.
service Commands service host stats Service statistics. 600 E-DOC-CTC-20071119-0014 v1.
service Commands service host triggerlist List all triggers. E-DOC-CTC-20071119-0014 v1.
service Commands service system ifadd Add an interface to the access list. SYNTAX: service system ifadd name = <{PPTP|HTTP|HTTPs|FTP|TELNET|RIP-Query| DNS-S|SNMP_AGENT|SSDP|MDAP|PING_RESPONDER}> group = <{wan|local|lan|tunnel|dmz|guest} or number> where: name The name of the service for this access list. REQUIRED group The interface group for this access list. REQUIRED 602 E-DOC-CTC-20071119-0014 v1.
service Commands service system ifdelete Delete an interface from the access list. SYNTAX: service system ifdelete name = <{PPTP|HTTP|HTTPs|FTP|TELNET|RIP-Query| DNS-S|SNMP_AGENT|SSDP|MDAP|PING_RESPONDER}> group = <{wan|local|lan|tunnel|dmz|guest} or number> where: name The name of the service for this access list. REQUIRED group The interface group for this access list. REQUIRED E-DOC-CTC-20071119-0014 v1.
service Commands service system ipadd Add an ip address (range) to the access list. SYNTAX: service system ipadd name = <{PPTP|HTTP|HTTPs|FTP|TELNET|RIP-Query| DNS-S|SNMP_AGENT|SSDP|MDAP|PING_RESPONDER}> ip = where: name The name of the service for this access list. REQUIRED ip The ip address (range) for this access list. REQUIRED 604 E-DOC-CTC-20071119-0014 v1.
service Commands service system ipdelete Delete an ip address (range) from the access list. SYNTAX: service system ipdelete name = <{PPTP|HTTP|HTTPs|FTP|TELNET|RIP-Query| DNS-S|SNMP_AGENT|SSDP|MDAP|PING_RESPONDER}> ip = where: name The name of the service for this access list. REQUIRED ip The ip address (range) for this access list. REQUIRED E-DOC-CTC-20071119-0014 v1.
service Commands service system list Display services. SYNTAX: service system list [name = <{PPTP|PPTPD|PPTPGRE|SNTP| SLA_ICMP_PING|SLA_UDP_PING|HTTP|HTTPs|RAD| Dynamic DNS|dyndns|statdns|custom|No-IP|DtDNS| gnudip|DHCP-S|DHCP-R|SNMP_AGENT|SSDP|MDAP| CWMP-C|CWMP-S|RAS|SRAS|IP_COMMANDS|ICMP_PING| SENDTO|PING_RESPONDER|ICMP_TRACEROUTE| UDP_TRACEROUTE|HTTPPROBE}]> [expand = <{disabled|enabled}]> [dynamics = <{disabled|enabled}]> [members = <{disabled|enabled}]> where: name The name of the service.
service Commands service system mapadd Add a port map for a service.
service Commands service system mapdelete Delete a port map for a service.
service Commands service system modify Modify a service.
snmp Commands 610 E-DOC-CTC-20071119-0014 v1.
snmp Commands snmp Commands snmp community add Config an SNMP community string to allow snmp access over IP. see page 612 snmp community delete Delete an SNMP community string to prevent snmp access over IP. see page 613 snmp community list List all SNMP community strings in use for snmp access over IP. see page 614 snmp community modify Modify an SNMP community string to allow snmp access over IP. see page 615 snmp config Configure global SNMP parameters.
snmp Commands snmp community add Config an SNMP community string to allow snmp access over IP. SYNTAX: snmp community add securityname = <{RWCommunity|ROCommunity}> communityname = where: securityname Configure access rights/restrictions control for the community name. REQUIRED communityname Configure SNMP community name. REQUIRED 612 E-DOC-CTC-20071119-0014 v1.
snmp Commands snmp community delete Delete an SNMP community string to prevent snmp access over IP. SYNTAX: snmp community delete securityname = <{RWCommunity|ROCommunity}> where: securityname E-DOC-CTC-20071119-0014 v1.0 Access rights/restrictions control of the community name to be deleted.
snmp Commands snmp community list List all SNMP community strings in use for snmp access over IP. 614 E-DOC-CTC-20071119-0014 v1.
snmp Commands snmp community modify Modify an SNMP community string to allow snmp access over IP. SYNTAX: snmp community modify securityname = <{RWCommunity|ROCommunity}> communityname = where: securityname Configure access rights/restrictions control for the community name. REQUIRED communityname Configure SNMP community name. REQUIRED E-DOC-CTC-20071119-0014 v1.
snmp Commands snmp config Configure global SNMP parameters. SYNTAX: snmp config [sysContact = [sysName = [sysLocation = where: sysContact SNMP System Contact OPTIONAL sysName SNMP System Name OPTIONAL sysLocation SNMP System Location OPTIONAL 616 E-DOC-CTC-20071119-0014 v1.
snmp Commands snmp get Get from supplied object identity. e.g. get objectid=.1.3.6.1.2.1.1.1.0 SYNTAX: snmp get [objectid = where: objectid E-DOC-CTC-20071119-0014 v1.0 Object identity to get from ... must include the instance which is 0 for scalar objects e.g. .1.3.6.1.2.1.1.1.
snmp Commands snmp getnext Get next from supplied object identity. e.g. getnext objectid= SYNTAX: snmp getnext [objectid = where: objectid 618 Object identity to getNext from e.g. .1.3.6.1.2.1.1 system returns sysDescription OPTIONAL E-DOC-CTC-20071119-0014 v1.
snmp Commands snmp ifadd Create a new SNMP interface. SYNTAX: snmp ifadd intf = dest = <{loop|ethif1|ethif2|ethif3|ethif4| wlif1|ceoc|bridge|OBC|ethport1|Internet_ppp| Internet|LocalNetwork}> where: intf The name for the new SNMP interface. REQUIRED dest The destination interface for this SNMP interface. REQUIRED E-DOC-CTC-20071119-0014 v1.
snmp Commands snmp ifattach Attach an SNMP interface. SYNTAX: snmp ifattach intf = <{loop|ethif1|ethif2|ethif3|ethif4| wlif1|ceoc|bridge|OBC|ethport1|Internet_ppp| Internet|LocalNetwork}> where: intf 620 The name of the SNMP interface. REQUIRED E-DOC-CTC-20071119-0014 v1.
snmp Commands snmp ifconfig Modify an SNMP interface. SYNTAX: snmp ifconfig intf = <{loop|ethif1|ethif2|ethif3|ethif4| wlif1|ceoc|bridge|OBC|ethport1|Internet_ppp| Internet|LocalNetwork}> [securityname = <{RWCommunity|ROCommunity}]> [communityname = where: intf The name of the SNMP interface to configure. REQUIRED securityname Configure access rights/restrictions control for the community name. OPTIONAL communityname Configure SNMP community name. OPTIONAL E-DOC-CTC-20071119-0014 v1.
snmp Commands snmp ifdelete Delete an SNMP interface. SYNTAX: snmp ifdelete intf = <{loop|ethif1|ethif2|ethif3|ethif4| wlif1|ceoc|bridge|OBC|ethport1|Internet_ppp| Internet|LocalNetwork}> where: intf 622 The name of the SNMP interface. REQUIRED E-DOC-CTC-20071119-0014 v1.
snmp Commands snmp ifdetach Detach an SNMP interface. SYNTAX: snmp ifdetach intf = <{loop|ethif1|ethif2|ethif3|ethif4| wlif1|ceoc|bridge|OBC|ethport1|Internet_ppp| Internet|LocalNetwork}> where: intf E-DOC-CTC-20071119-0014 v1.0 The name of the SNMP interface.
snmp Commands snmp iflist Display the SNMP interfaces. SYNTAX: snmp iflist [intf = <{loop|ethif1|ethif2|ethif3|ethif4| wlif1|ceoc|bridge|OBC|ethport1|Internet_ppp| Internet|LocalNetwork}]> where: intf 624 The name of an SNMP interface. OPTIONAL E-DOC-CTC-20071119-0014 v1.
snmp Commands snmp walk Walk from supplied object identity. e.g. walk objectid=.1.3.6.1.2.1.1 SYNTAX: snmp walk [objectid = where: objectid E-DOC-CTC-20071119-0014 v1.0 Object identity to walk from e.g. .1.3.6.1.2.1.
sntp Commands 626 E-DOC-CTC-20071119-0014 v1.
sntp Commands sntp Commands sntp add Add NTP server see page 628 sntp config Modify/Display configuration see page 629 sntp debug traceconfig Modify SNTP client trace configuration see page 630 sntp delete Delete NTP server from list see page 631 sntp flush Flush NTP server list and SNTP client configuration see page 632 sntp list List the NTP servers see page 633 E-DOC-CTC-20071119-0014 v1.
sntp Commands sntp add Add NTP server SYNTAX: sntp add [addr = [name = [version = where: addr IP address of NTP server to be added to list OPTIONAL name DNS name of NTP server to be added to list. If both the IP address and the DNS name are provided, the IP address is ignored. OPTIONAL version SNTP version of server (1,2,3 or 4) OPTIONAL 628 E-DOC-CTC-20071119-0014 v1.
sntp Commands sntp config Modify/Display configuration SYNTAX: sntp config [state = <{enabled|disabled}]> [poll = [pollpresync = where: state Enable/Disable SNTP client OPTIONAL poll polling interval (1 min, ... ,10080min(=7days)) OPTIONAL pollpresync polling interval before first sync (1 min, ... ,60min) OPTIONAL E-DOC-CTC-20071119-0014 v1.
sntp Commands sntp debug traceconfig Modify SNTP client trace configuration SYNTAX: sntp debug traceconfig [state = <{disabled|enabled}]> where: state 630 Enable/Disable tracing. OPTIONAL E-DOC-CTC-20071119-0014 v1.
sntp Commands sntp delete Delete NTP server from list SYNTAX: sntp delete [addr = [name = where: addr IP address of NTP server to be removed from list OPTIONAL name DNS name of NTP server to be removed from list OPTIONAL E-DOC-CTC-20071119-0014 v1.
sntp Commands sntp flush Flush NTP server list and SNTP client configuration 632 E-DOC-CTC-20071119-0014 v1.
sntp Commands sntp list List the NTP servers E-DOC-CTC-20071119-0014 v1.
software Commands 634 E-DOC-CTC-20071119-0014 v1.
software Commands software Commands software download Download parameters. see page 636 software upgrade Reboots the modem to initiate the SW upgrade. New software available on a see page 637 software version Displays the software version. see page 638 E-DOC-CTC-20071119-0014 v1.
software Commands software download Download parameters. SYNTAX: software download filetype = <{firmware|configuration}> url = [username = [password = filesize = [targetfilename = where: filetype The type of the file to be downloaded. REQUIRED url Set the HTTP URL where the file is to be found including remote filename. REQUIRED username Set the name to be used to authenticate to the download server.
software Commands software upgrade Reboots the modem to initiate the SW upgrade. New software available on a E-DOC-CTC-20071119-0014 v1.
software Commands software version Displays the software version. 638 E-DOC-CTC-20071119-0014 v1.
system Commands system Commands system config Set or change system config parameters. see page 640 system debug autosave Autosave debugging commands see page 641 system debug stats Cpu and memory statistics see page 642 system dst Set daylight saving values see page 643 system flush Flush system configuration. see page 645 system locale Set/Get regional settings. see page 646 system ra config Configure Remote assistance params. see page 647 system reboot Reboot the modem.
system Commands system config Set or change system config parameters.
system Commands system debug autosave Autosave debugging commands SYNTAX: system debug autosave [trace = <{disabled|enabled}]> where: trace E-DOC-CTC-20071119-0014 v1.
system Commands system debug stats Cpu and memory statistics SYNTAX: system debug stats [reset = <{disabled|enabled}]> where: reset 642 Reset cpu statistics. OPTIONAL E-DOC-CTC-20071119-0014 v1.
system Commands system dst Set daylight saving values SYNTAX: system dst [status = <{Disable|Enable}]> [mode = <{Absolute|Relative}]> [startdate =
- [starttime = [enddate =
- [endtime = [startweekday = <{Monday|Tuesday|Wednesday| Thursday|Friday|Saturday|Sunday}]> [starthour = [startweek = [startmonth = [endweekday = <{Monday|Tuesday|Wednesday| Thursday|Friday|Saturday|Sunday}]> [endhour = [endwe
system Commands endweekday Set the end weekday of the daylight saving in the relative mode OPTIONAL endhour Set the end hour of the daylight saving in the relative mode OPTIONAL endweek Set the end week of the daylight saving in the relative mode OPTIONAL endmonth Set the end month of the daylight saving in the relative mode OPTIONAL 644 E-DOC-CTC-20071119-0014 v1.
system Commands system flush Flush system configuration. E-DOC-CTC-20071119-0014 v1.
system Commands system locale Set/Get regional settings. SYNTAX: system locale [dec_symbol = <{,|.}]> [group_symbol = <{.|,}]> [date_separator = <{/|-|.
system Commands system ra config Configure Remote assistance params. SYNTAX: system ra config [secure = <{disabled|enabled}]> [port = [timeout = where: secure Enable/Disable https. OPTIONAL port Set destination port. OPTIONAL timeout Set connection timeout in minutes. OPTIONAL E-DOC-CTC-20071119-0014 v1.
system Commands system reboot Reboot the modem. 648 E-DOC-CTC-20071119-0014 v1.
system Commands system reset Reset to (factory or ISP) defaults: user specific settings will be cleared ! SYNTAX: system reset factory = <{yes|no}> proceed = <{no|yes}> where: factory Option to reset to factory REQUIRED proceed Confirmation for resetting the modem. REQUIRED E-DOC-CTC-20071119-0014 v1.
system Commands system settime Set/Get date, time, timezone, daylight savings time, uptime. SYNTAX: system settime [time = [timezone = <(+ or -)hh:mm]> [daylightsaving = <{disabled|enabled}]> [geotimezonename = [rtc = <{disabled|enabled}]> where: time Set the system time OPTIONAL timezone Set the system timezone(-12:00...
system Commands system timedreboot Set or change editing mode timed reboot SYNTAX: system timedreboot [state = <{disabled|enabled}]> [time = [date = where: state Enable/Disable timed reboot OPTIONAL time Change default countdown time (Min). OPTIONAL date Set date/time to reboot (DD/MM/YYYY/HH:MM). OPTIONAL E-DOC-CTC-20071119-0014 v1.
systemlog Commands 652 E-DOC-CTC-20071119-0014 v1.
systemlog Commands systemlog Commands systemlog flush Flush all messages in syslog message buffer. see page 654 systemlog send Send messages to remote syslog server. see page 655 systemlog show Show messages in the syslog message buffer. see page 656 E-DOC-CTC-20071119-0014 v1.
systemlog Commands systemlog flush Flush all messages in syslog message buffer. 654 E-DOC-CTC-20071119-0014 v1.
systemlog Commands systemlog send Send messages to remote syslog server. SYNTAX: systemlog send [fac = <{kern|user|mail|daemon|auth|syslog| lpr|news|uucp|cron|security|ftp|local6| local7}]> [sev = <{emerg|alert|crit|err|warning|notice| info|debug}]> [hist = <{disabled|enabled}]> dest = where: fac Syslog facility level. OPTIONAL sev Syslog severity level.
systemlog Commands systemlog show Show messages in the syslog message buffer. SYNTAX: systemlog show [fac = <{kern|user|mail|daemon|auth|syslog| lpr|news|uucp|cron|security|ftp|local6| local7}]> [sev = <{emerg|alert|crit|err|warning|notice| info|debug}]> [hist = <{disabled|enabled}]> where: fac Syslog facility level. OPTIONAL sev Syslog severity level. OPTIONAL hist Syslog display message history (over several bootups) OPTIONAL 656 E-DOC-CTC-20071119-0014 v1.
tls Commands tls Commands tls acs-client cert add Add a new certificate see page 658 tls acs-client cert delete Delete a certificate see page 659 tls acs-client cert list List certificates see page 660 tls acs-client config Display/modify tls settings see page 661 tls https-server cert add Add a new certificate see page 662 tls https-server cert delete Delete a certificate see page 663 tls https-server cert list List certificates see page 664 tls https-server config Display/modify tls
tls Commands tls acs-client cert add Add a new certificate SYNTAX: tls acs-client cert add filename = where: filename 658 name of the certificate file REQUIRED E-DOC-CTC-20071119-0014 v1.
tls Commands tls acs-client cert delete Delete a certificate SYNTAX: tls acs-client cert delete index = where: index E-DOC-CTC-20071119-0014 v1.
tls Commands tls acs-client cert list List certificates SYNTAX: tls acs-client cert list [index = [expand = <{disabled|enabled}]> where: index Certificate index OPTIONAL expand Display more information OPTIONAL 660 E-DOC-CTC-20071119-0014 v1.
tls Commands tls acs-client config Display/modify tls settings SYNTAX: tls acs-client config [state = <{disabled|enabled}]> [auth-serv = <{disabled|enabled}]> [valid-date = <{disabled|enabled}]> [valid-domain = <{disabled|enabled}]> where: state SSL/TLS client for ACS state OPTIONAL auth-serv Request server authentication OPTIONAL valid-date Check certificate validity date OPTIONAL valid-domain Check certificate domain OPTIONAL E-DOC-CTC-20071119-0014 v1.
tls Commands tls https-server cert add Add a new certificate SYNTAX: tls https-server cert add filename = where: filename 662 name of the certificate file REQUIRED E-DOC-CTC-20071119-0014 v1.
tls Commands tls https-server cert delete Delete a certificate SYNTAX: tls https-server cert delete index = where: index E-DOC-CTC-20071119-0014 v1.
tls Commands tls https-server cert list List certificates SYNTAX: tls https-server cert list [index = [expand = <{disabled|enabled}]> where: index Certificate index OPTIONAL expand Display more information OPTIONAL 664 E-DOC-CTC-20071119-0014 v1.
tls Commands tls https-server config Display/modify tls settings SYNTAX: tls https-server config [state = <{disabled|enabled}]> [auth-client = <{disabled|enabled}]> [valid-date = <{disabled|enabled}]> where: state SSL/TLS server for HTTPS state OPTIONAL auth-client Request client authentication OPTIONAL valid-date Check certificate validity date OPTIONAL E-DOC-CTC-20071119-0014 v1.
tls Commands tls self cert list List certificates SYNTAX: tls self cert list [index = [expand = <{disabled|enabled}]> where: index Certificate index OPTIONAL expand Display more information OPTIONAL 666 E-DOC-CTC-20071119-0014 v1.
traceroute Command traceroute Command Send ICMP/UDP packets to trace the ip path. SYNTAX: traceroute addr = [count = [size = [interval = [maxhops = [dstport = [maxfail = [type = <{icmp|udp}]> [utime = <{disabled|enabled}]> where: addr The destination IP address. REQUIRED count The number of times to reissue a traceroute request with the same time to live.
upgrade Commands 668 E-DOC-CTC-20071119-0014 v1.
upgrade Commands upgrade Commands upgrade config Change the upgrade daemon configuration see page 670 upgrade debug sesslist Display the list of sessions see page 671 upgrade debug traceconfig Enable/disable upgrade daemon tracing see page 672 upgrade profile add Add a new file profile description see page 673 upgrade profile delete Delete a file profile description see page 674 upgrade profile list Display a list of the file profile descriptions see page 675 upgrade profile modify Modif
upgrade Commands upgrade config Change the upgrade daemon configuration SYNTAX: upgrade config [state = <{disabled|enabled}]> [protocol = <{tftp|ftp|http|https}]> where: state The upgrade daemon state OPTIONAL protocol The transfer protocol to be used for file download OPTIONAL 670 E-DOC-CTC-20071119-0014 v1.
upgrade Commands upgrade debug sesslist Display the list of sessions E-DOC-CTC-20071119-0014 v1.
upgrade Commands upgrade debug traceconfig Enable/disable upgrade daemon tracing SYNTAX: upgrade debug traceconfig state = <{disabled|enabled}> where: state 672 The upgrade daemon trace state REQUIRED E-DOC-CTC-20071119-0014 v1.
upgrade Commands upgrade profile add Add a new file profile description SYNTAX: upgrade profile add extension = <{sts|ini|bin}> [maxsize(KBytes) = action = <{none|config_load|script_load| reboot|upgrade}> where: extension The extension of the new file profile REQUIRED maxsize(KBytes) The maximum filesize (in KBytes) allowed for files with the extension of this profile OPTIONAL action The action to be done when the file with the extension of this profile is downloaded REQUIRED E-DOC-CTC
upgrade Commands upgrade profile delete Delete a file profile description SYNTAX: upgrade profile delete extension = <{sts|ini|bin}> where: extension 674 The extension of the file profile to be deleted REQUIRED E-DOC-CTC-20071119-0014 v1.
upgrade Commands upgrade profile list Display a list of the file profile descriptions E-DOC-CTC-20071119-0014 v1.
upgrade Commands upgrade profile modify Modify a file profile description SYNTAX: upgrade profile modify extension = <{sts|ini|bin}> [maxsize(KBytes) = action = <{none|config_load|script_load| reboot|upgrade}> where: extension The extension of the new file profile REQUIRED maxsize(KBytes) The maximum filesize (in KBytes) allowed for files with the extension of this profile OPTIONAL action The action to be done when the file with the extension of this profile is downloaded REQUIRED 676
upgrade Commands upgrade start Start a new upgrade SYNTAX: upgrade start protocol = <{tftp|ftp|http|https}> [server = [filename = where: protocol The protocol to be used for the download REQUIRED server The server name or IP address OPTIONAL filename The file to be downloaded OPTIONAL E-DOC-CTC-20071119-0014 v1.
upnp Commands 678 E-DOC-CTC-20071119-0014 v1.
upnp Commands upnp Commands upnp config Config upnp parameter(s) see page 680 upnp flush Flushes upnp config (i.e. to defaults) see page 681 upnp list List all registered devices see page 682 E-DOC-CTC-20071119-0014 v1.
upnp Commands upnp config Config upnp parameter(s) SYNTAX: upnp config [maxage = [writemode = <{full|natonly|readonly}]> [safenat = <{disabled|enabled}]> [preferredaddresses = where: maxage ssdp advertisements MAX-AGE (default = 1800) OPTIONAL writemode Configuration access level for UPnP OPTIONAL safenat Enable / disable check on safe nat entries (limited to own host) OPTIONAL preferredaddresses CSV list of preferred ip addresses for UPnP (1 per lan ip-interface)
upnp Commands upnp flush Flushes upnp config (i.e. to defaults) E-DOC-CTC-20071119-0014 v1.
upnp Commands upnp list List all registered devices SYNTAX: upnp list [verbose = where: verbose 682 Verbose level (default = 1) OPTIONAL E-DOC-CTC-20071119-0014 v1.
user Commands user Commands user add Add a user. see page 684 user config Modify the user. see page 685 user delete Delete a user. see page 686 user flush Flush the users. see page 687 user list Display the users. see page 688 user rights Display session rights. see page 689 E-DOC-CTC-20071119-0014 v1.
user Commands user add Add a user. SYNTAX: user add name = password = role = <> [hash2 = [descr = [defuser = <{disabled|enabled}]> [defremadmin = <{disabled|enabled}]> [deflocadmin = <{disabled|enabled}]> where: name User name. REQUIRED password User password. REQUIRED role Role name. REQUIRED hash2 The MD5 hash. OPTIONAL descr User description. OPTIONAL defuser Set this user as the default user.
user Commands user config Modify the user. SYNTAX: user config name = <{Administrator|tech}> [password = [role = <]> [descr = [defuser = <{disabled|enabled}]> [defremadmin = <{disabled|enabled}]> [deflocadmin = <{disabled|enabled}]> where: name User name. REQUIRED password User password. OPTIONAL role Role name. OPTIONAL descr User description. OPTIONAL defuser Set this user as the default user.
user Commands user delete Delete a user. SYNTAX: user delete name = <{Administrator|tech}> where: name 686 User name. REQUIRED E-DOC-CTC-20071119-0014 v1.
user Commands user flush Flush the users. E-DOC-CTC-20071119-0014 v1.
user Commands user list Display the users. SYNTAX: user list [name = <{Administrator|tech}]> [channel = <{ftp|telnet|http|mdap|serial}]> [origin = <{lan|wan|local}]> [secure = <{disabled|enabled}]> where: name User name. OPTIONAL channel The selected channel. OPTIONAL origin The selected origin. OPTIONAL secure The selected security level. OPTIONAL 688 E-DOC-CTC-20071119-0014 v1.
user Commands user rights Display session rights. E-DOC-CTC-20071119-0014 v1.
wireless Commands 690 E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless Commands wireless debug stats Transfer statistics see page 693 wireless debug txpower TX power override see page 694 wireless ifconfig Configures wireless settings.
wireless Commands wireless secmode config Configure/Show the security mode. see page 718 wireless secmode wep Configure WEP settings. see page 719 wireless secmode wpa-psk Configure WPA-PSK settings.
wireless Commands wireless debug stats Transfer statistics E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless debug txpower TX power override SYNTAX: wireless debug txpower [txpwr = where: txpwr 694 TX power in milliwatt OPTIONAL E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless ifconfig Configures wireless settings. SYNTAX: wireless ifconfig [state = <{enabled|disabled}]> [channel = <{auto|1|2|3|4|5|6|7|8|9|10|11|12| 13}]> [ssid = [any = <{enabled|disabled}]> [interop = <{802.11b|802.11b(legacy)/g| 802.11b/g|802.
wireless Commands wireless macacl add Add an ACL MAC entry SYNTAX: wireless macacl add [ssid_id = hwaddr = permission = <{allow|deny}> [name = where: ssid_id ssid id OPTIONAL hwaddr The Ethernet MAC address of the ACL entry REQUIRED permission The action to be performed on ACL entry REQUIRED name The name of the station OPTIONAL 696 E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless macacl config Access Control List configuration SYNTAX: wireless macacl config [ssid_id = [control = <{lock|unlock|register}]> [regtime = where: ssid_id ssid id OPTIONAL control Access Control List mode OPTIONAL regtime Registration time OPTIONAL E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless macacl delete Delete an ACL MAC entry SYNTAX: wireless macacl delete ssid_id = hwaddr = where: ssid_id ssid id REQUIRED hwaddr hardware address of the ACL entry REQUIRED 698 E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless macacl flush Flushes ACL entries SYNTAX: wireless macacl flush [ssid_id = proceed = <{disabled|enabled}> where: ssid_id ssid id OPTIONAL proceed Confirmation required REQUIRED E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless macacl list Shows a list of all configured ACL entries SYNTAX: wireless macacl list [ssid_id = where: ssid_id 700 ssid id OPTIONAL E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless macacl modify Modify an ACL entry SYNTAX: wireless macacl modify ssid_id = hwaddr = [permission = <{allow|deny}]> [name = where: ssid_id ssid id REQUIRED hwaddr The Ethernet MAC address of the ACL entry REQUIRED permission The action to be performed on ACL entry OPTIONAL name The name of the station OPTIONAL E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless macacl register Start a registration process (only for register mode) SYNTAX: wireless macacl register proceed = <{disabled|enabled}> where: proceed 702 Confirmation required REQUIRED E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless mssid ifadd Add an extra ssid context SYNTAX: wireless mssid ifadd ssid = where: ssid E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless mssid ifattach Attach a ssid context SYNTAX: wireless mssid ifattach ssid_id = where: ssid_id 704 ssid REQUIRED E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless mssid ifconfig Configure a ssid context SYNTAX: wireless mssid ifconfig ssid_id = [ssid = [apisolation = <{disabled|enabled}]> [any = <{disabled|enabled}]> [secmode = <{disable|wep|wpa-psk}]> [WEPkey = [WPAPSKkey = [WPAPSKversion = <{WPA|WPA2|WPA+WPA2}]> [addscript = [delscript = [trace = <{disabled|enabled}]> where: ssid_id ssid id REQUIRED ssid ssid OPTIONAL apisolation ap isola
wireless Commands wireless mssid ifdelete Delete a ssid context SYNTAX: wireless mssid ifdelete ssid_id = where: ssid_id 706 ssid REQUIRED E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless mssid ifdetach Detach a ssid context SYNTAX: wireless mssid ifdetach ssid_id = where: ssid_id E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless mssid iflist Multiple ssid configuration SYNTAX: wireless mssid iflist [ssid_id = where: ssid_id 708 ssid OPTIONAL E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless multiuni add add a multicast to unicat mapping SYNTAX: wireless multiuni add multicast = unicast = where: multicast Multicast MAC REQUIRED unicast Unicast MAC REQUIRED E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless multiuni delete delete all multicast mappings SYNTAX: wireless multiuni delete multicast = where: multicast 710 Multicast MAC REQUIRED E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless multiuni flush flush all multicast to unicast mappings E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless multiuni list show configured multicast to unicast mappings 712 E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless multiuni scanresults display detected multicast mac addresses SYNTAX: wireless multiuni scanresults [rescan = <{no|yes}]> where: rescan E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless qos apacconfig configure AP EDCA parameters SYNTAX: wireless qos apacconfig [class = <{AC_BE|AC_BK|AC_VI|AC_VO}]> [cwmax = <{1|3|7|15|31|63|127|255|511|1023| 2047|4095|8191|16383|32767}]> [cwmin = <{0|1|3|7|15|31|63|127|255}]> [aifsn = [txop = where: class AC class OPTIONAL cwmax CWmax configuration OPTIONAL cwmin CWmin configuration OPTIONAL aifsn Aifsn configuration OPTIONAL txop txoplimit [us] configuration OPTIONAL 714 E-DOC-CTC-200
wireless Commands wireless qos config configure QoS settings SYNTAX: wireless qos config [mode = <{disabled|wmm}]> where: mode E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless qos staacconfig configure STA EDCA parameters SYNTAX: wireless qos staacconfig [class = <{AC_BE|AC_BK|AC_VI|AC_VO}]> [cwmax = <{1|3|7|15|31|63|127|255|511|1023| 2047|4095|8191|16383|32767}]> [cwmin = <{0|1|3|7|15|31|63|127|255}]> [aifsn = [txop = where: class AC class OPTIONAL cwmax CWmax configuration OPTIONAL cwmin CWmin configuration OPTIONAL aifsn Aifsn configuration OPTIONAL txop txoplimit [us] configuration OPTIONAL 716 E-DOC-CTC-
wireless Commands wireless reset Reset Wireless interface settings to defaults SYNTAX: wireless reset proceed = <{disabled|enabled}> where: proceed E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless secmode config Configure/Show the security mode. SYNTAX: wireless secmode config [mode = <{disable|wep|wpa-psk}]> where: mode 718 security mode OPTIONAL E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless secmode wep Configure WEP settings. SYNTAX: wireless secmode wep [encryptionkey = where: encryptionkey E-DOC-CTC-20071119-0014 v1.0 WEP key: expected format 5 or 13 ASCII characters, or 10 or 26 HEX digits.
wireless Commands wireless secmode wpa-psk Configure WPA-PSK settings. SYNTAX: wireless secmode wpa-psk [presharedkey = [version = <{WPA|WPA2|WPA+WPA2}]> where: presharedkey WPA-PSK key: expected format 8 to 63 ASCII characters or 64 HEX digits. OPTIONAL version wpa version OPTIONAL 720 E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless stations list List of the currently associated stations SYNTAX: wireless stations list [hwaddr = [ssid_id = where: hwaddr The MAC address of station OPTIONAL ssid_id Selected BSS OPTIONAL E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless wds add add WDS station SYNTAX: wireless wds add bssid = [name = where: bssid The WDS bssid REQUIRED name A user specified reference name OPTIONAL 722 E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless wds config WDS configuration parameters SYNTAX: wireless wds config [state = <{disabled|enabled}]> where: state E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless wds delete delete WDS station SYNTAX: wireless wds delete bssid = where: bssid 724 The WDS bssid REQUIRED E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless wds flush Flush all wds stations E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless wds list list WDS stations 726 E-DOC-CTC-20071119-0014 v1.
wireless Commands wireless wds scanresults scan all networks SYNTAX: wireless wds scanresults [rescan = <{disabled|enabled}]> where: rescan E-DOC-CTC-20071119-0014 v1.
xdsl Commands 728 E-DOC-CTC-20071119-0014 v1.
xdsl Commands xdsl Commands xdsl config Modify/Display dsl configuration see page 730 xdsl debug bitloadinginfo Displays # bits per tone see page 731 xdsl debug deltconfig Dual Ended Line Testing interface see page 732 xdsl debug deltinfo Dual Ended Line Test result display see page 733 xdsl debug modemoptioninfo The modem options bitmap display see page 734 xdsl debug multimode Config custom multimode see page 735 xdsl debug traceconfig Config the adsl tracelevel see page 736 xdsl inf
xdsl Commands xdsl config Modify/Display dsl configuration SYNTAX: xdsl config [adslmultimode = <{adsl|adsl2|adsl2plus}]> [detect-lop = <{disabled|enabled}]> [syslog = <{disabled|enabled}]> where: adslmultimode Set/Show selected multimode type of the modem OPTIONAL detect-lop Detect Loss Of Power OPTIONAL syslog Log in syslog during showtime OPTIONAL 730 E-DOC-CTC-20071119-0014 v1.
xdsl Commands xdsl debug bitloadinginfo Displays # bits per tone E-DOC-CTC-20071119-0014 v1.
xdsl Commands xdsl debug deltconfig Dual Ended Line Testing interface SYNTAX: xdsl debug deltconfig [state = <{disabled|enabled}]> where: state 732 Enable/Disable dual ended line testing OPTIONAL E-DOC-CTC-20071119-0014 v1.
xdsl Commands xdsl debug deltinfo Dual Ended Line Test result display E-DOC-CTC-20071119-0014 v1.
xdsl Commands xdsl debug modemoptioninfo The modem options bitmap display 734 E-DOC-CTC-20071119-0014 v1.
xdsl Commands xdsl debug multimode Config custom multimode SYNTAX: xdsl debug multimode [config = <[+/-]flag[+/-flag...]{default t1.413issue2 g992.1_annex_a g992.2 g992.5_annex_m}]> where: config E-DOC-CTC-20071119-0014 v1.
xdsl Commands xdsl debug traceconfig Config the adsl tracelevel SYNTAX: xdsl debug traceconfig level = <{0|1|2|3|4}> where: level 736 Trace Level (0=disable tracing; 1=enable dsl manager tracing; 2=enable dsl driver tracing) REQUIRED E-DOC-CTC-20071119-0014 v1.
xdsl Commands xdsl info Displays status information about modem SYNTAX: xdsl info [expand = <{disabled|enabled}]> [g.997.1 = <{disabled|enabled}]> [counter_period_filter = <{current|15_minutes| 24_hours}]> [counters_reset = <{no|yes}]> where: expand Condensed / Expanded listing link information OPTIONAL g.997.
xdsl Commands xdsl version Display xdsl version information. 738 E-DOC-CTC-20071119-0014 v1.
THOMSON Telecom Belgium Prins Boudewijnlaan 47 www.thomson-broadband.com © 2007 Thomson. All rights reserved. E-DOC-CTC-20071119-0014 v1.