LCD MONITOR quick start guide 400DXn ii
Select Language Main Page Model Safety Instructions Introduction Package Contents Your LCD Display Machanical Layout Connections Using the Software Adjusting the LCD Display Troubleshooting Specifications The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.
Batteries (AAA X 2) Remote Control (Not available in all Cover-Hole locations) BNC to RCA Adaptor Jack Semi Stand Screw: 4 EA USB Holder & Screw (1EA) Sold separately Wall Mount KIT Speaker Set BNC Cable LAN Cable DVI Cable Your LCD Display Front 1) MENU Opens the on-screen menu and exits from the menu or closes the adjustment menu.
2) Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values. 3) Adjust buttons (Left-Right buttons)/ Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values. Adjusts the audio volume. 4) ENTER Activates a highlighted menu item. 5) SOURCE Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the LCD Display at the time.
1) POWER S/W ON [ | ] / OFF [O] Switches the LCD Display On/Off. 2) POWER IN The power cord plugs into the LCD Display and the wall plug. 3) REMOTE OUT/IN You can use a wired remote control by connecting it to your monitor.
12) AV AUDIO IN [L-AUDIO-R] (LCD Display Audio Connection Terminal (Input)) 13) AV OUT [VIDEO] (VIDEO Connection Terminal): AV mode (Output) 14) AV IN [VIDEO] (VIDEO Connection Terminal) (Input) 15) AV OUT [S-VIDEO] (S-VIDEO Connection Terminal): S-VIDEO mode (Output) 16) AV IN [S-VIDEO] (S-VIDEO Connection Terminal) (Input) 17) EXT SPEAKER(8 Ω)[- - L - +, - - R - +] (EXT Speaker Connection Terminal) 18) AUDIO OUT [L-AUDIO-R] (LCD Display Audio Connection Terminal (Output)) AUDIO OUT is the terminal for sou
. VOL 8. MUTE 9. TTX/MIX 10. MENU 11. ENTER 12. P.MODE 13. AUTO 14. ENTER/PRE-CH 15 . CH/P 16. SOURCE 17. INFO 18. EXIT 19. Up-Down Left-Right buttons 20. S.MODE 21. STILL 22. FM RADIO 23. P.SIZE 24. 25. SRS DUAL/MTS 26. PIP 27. SOURCE 28. SWAP 29. 30. 31. 32. 33. 1) SIZE REW STOP PLAY/PAUSE FF ON / OFF Turns the LCD Display On/Off. 2) MAGICNET MagicNet Quick Launch Button. 3) MDC MDC Quick Launch Button.
12) P.MODE When you press this button, current picture mode is displayed on the lower center of the screen. AV / S-Video / Component : P.MODE The Monitor has four automatic picture settings that are preset at the factory. Then push button again to circle through available preconfigured modes. ( Dynamic → Standard → Movie → Custom ) PC/DVI/BNC : M/B (MagicBright™) MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching.
Every time you press the button, a PIP screen appears. 27) SOURCE Changes the source of the PIP window signal. 28) SWAP Swaps the contents of the PIP and main image. The image in the PIP window will appear on the main screen, and the main screen image will appear in the PIP window. 29) SIZE Switches the PIP Picture Size. 30) REW Rewind 31) STOP Stop 32) PLAY / PAUSE Play/Pause 33) FF Fast forward © 1995~2007 SAMSUNG.
Select Language Main Page Model Safety Instructions Introduction Connections Installing the Stand KIT Connecting the LCD Display Using the Software Adjusting the LCD Display Troubleshooting Specifications The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement. Connections Information Installing the Stand KIT Appendix Note • Only the supplied bolts should be used.
Connecting the LCD Display Using a Power cord with Earth In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un-wiring the earth lead, make sure to disconnect the AC power in advance. Note • AV input devices such as DVD players, VCR's or camcorders as well as your computer can be connected to the LCD Display.
3) Connect the audio cable for your LCD Display to the audio port on the back of your computer. Note • Turn on both your computer and the LCD Display. Note • The DVI cable or BNC cable is optional. Contact a local Samsung Electronics Service Center to buy optional items. Connecting a VCR 1) AV input devices such as VCRs or Camcorders are connected via the AV IN [VIDEO] or AV IN [S-VIDEO] of the LCD Display using an S-VHS or BNC cable.
1) Connect a set of audio cables between the COMPONENT AUDIO IN [L-AUDIO-R] on the LCD Display and the AUDIO OUT jacks on the DVD player. 2) Connect a Component cable between the BNC/COMPONENT IN - PR, Y, PB port on the LCD Display and the PR, Y, PB jacks on the DVD player. Note • Select Component for the connection to a DVD player using the SOURCE button on the front of the LCD Display or on the remote control. • Then, start the DVD Player with a DVD disc inserted.
• The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store.) If your camcorder is stereo, you need to connect a set of two cables. Connecting a DTV Set Top Box Note • The connections for a typical Set Top Box are shown below. 1) Connect a Component cable between the BNC / COMPONENT IN - PR, Y, PB port on the LCD Display and the PR, Y, PB jacks on the Set Top Box.
Note • Connect the speaker connection cable between the speaker connection jack on the back of the SET and the speaker connection jack on the back of the speaker. Note • Do not move the SET while the SET is connected to the speakers. The speaker-bracket for connecting the SET speaker my become damaged. Connecting to an Audio System Note • Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and the AUDIO OUT [L-AUDIO-R] on LCD Display.
Note • You can control your monitor by allowing it to receive the remote control signals of other devices through the REMOTE OUT terminal. • You can control a device by allowing it to receive remote control signals from other devices through the REMOTE IN terminal. Note • Restrictions: Available only if other devices support the wired remote control I/O terminals. Connecting HDMI Note • Input devices such as digital DVD are connected to the HDMI IN terminal of the monitor using the HDMI cable.
1) Connect the LAN cable. Connecting a USB device 1) You can connect USB devices such as a mouse or keyboard. Using a USB Holder When using a small external device such as a portable memory stick and it is connected to the USB terminal at the back of your monitor, it is exposed to the possiblity of theft or loss. By installing a USB holder after the installation of an external device, you can prevent theft or loss.
1) Insert part 2) Align part of your USB holder with the groove at the bottom of part Align part of your USB holder with the bottom of part 3) of your USB holder into the groove in part at the back of your monitor. at the back of your monitor. at the back of your monitor. Insert a screw into the groove aligned in step [2], and fasten it. Align with and use a screw to fix them. © 1995~2007 SAMSUNG.
1) Insert part of your USB holder into the groove in part 2) Align part of your USB holder with the groove at the bottom of part Align part of your USB holder with the bottom of part 3) at the back of your monitor. at the back of your monitor. at the back of your monitor. Insert a screw into the groove aligned in step [2], and fasten it. Align with and use a screw to fix them. © 1995~2007 SAMSUNG.
Select Language Main Page Model Safety Instructions Introduction Connections Using the Software Adjusting the LCD Display Troubleshooting Self-Test Feature Check Check List Q&A Specifications The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.
Maintenance and Cleaning 1) Maintaining the LCD Display Case. Clean with a soft cloth after disconnecting the power cord. • Do not use benzene, thinner or other flammable substances, or a wet cloth. • We recommend that a Samsung cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.
Display is securely connected. The LCD Display screen flickers. (Refer to Connecting a Computer) Problems related to the Screen Note • Problems related to the LCD Display screen and their solutions are listed. Problems The screen is blank and the power Solutions z Ensure that the power cord is firmly connected and the LCD LCD Display is on. indicator is off. (Refer to the Connecting the LCD Display ) "Check Signal Cable" message.
• Problems related to audio signals and their solutions are listed below. Problems No sound. Solutions z Ensure that the audio cable is firmly connected to both the audio-in port on your LCD Display and the audio-out port on your sound card. (Refer to the Connecting the LCD Display ) The sound level is too low. z Check the volume level. z Check the volume level.
Set the resolution in the Control Panel → Appearance and Themes → Display → Settings. z Windows ME/2000: Set the resolution in the Control Panel → Display → Settings. * Contact the video card manufacturer for details. How can I set the Power Saving z Windows XP: Set the resolution in the Control Panel → Appearance and function? Themes → Display → Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual).
